Tender For Supply Of Spares Of Coal Mills (Hp-1103) To Rgtpp, Khedar, Hisar On Annual Rate Contract Basis.

Sharing tender

Supply Of Spares Of Coal Mills (Hp-1103) To Rgtpp, Khedar, Hisar On Annual Rate Contract Basis. , Supply Of Spares Of Coal Mills (Hp-1103)To Rgtpp Khedar Hisar On Annual Rate Contract Basis, For Qty & Detail Please Refer Annexure-1 Of Nit In Detail , Seal Wear Ring Of Coal Mill Journal Assembly Shaft, Od-470 Mm, Id-390 Mm, Width- 102 Mm, Moc-Ss304 , Journal Assembly Top Cover Plate For Coal Mill Hp-1103 , Journal Bearing Keeper Moc: En24 Forged, Od-456Mm, Id-105Mm, Pcd-232 Mm, 8 Nos. Of Holes Of Size M32, Thickness-40Mm , Journal Housing Seal Cover For Journal Assembly Of Coal Mills Moc:Is1020 Cast Steel/En24 , Roller Retainer Ring For Coal Mills Moc: 16Mn , Journal Housing Guard/Liner Lower, Moc- Ss-304 , Journal Housing Guard/Liner Upper, Moc: Cast Steel As Per Is 1030 Grade-2 , Roller Liner Device With Liners For Coal Mill, Base Plate: Ms, Liners : Ni Hard , Liner Rld Type-I, Moc: Ni Hard Along With Their Weld Plugs , Liner Rld Type-Ii, Moc: Ni Hard Along With Their Weld Plugs , Liner Rld Type-Iii, Moc: Ni Hard Along With Their Weld Plugs , Liner Rld Type-Iv, Moc: Ni Hard Along With Their Weld Plugs , Liner Rld Type-V, Moc: Ni Hard Along With Their Weld Plugs , Mill Bowl Hub Clamping Ring Moc- 16 Mn (1 Set=4 Nos.) , Shroud Plate1360x120x10 Ms (1 Set = 8 Nos.) , Air Restriction Ring Large1800x60x28 Ms (1 Set = 8 Nos.) , Air Restriction Ring Small 1800X60x28 Ms (1 Set = 8 Nos.) , Mill Body Deflector Support Base Plate Ms (1 Set = 3 Nos.) , Separator Body Liner-I , Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Il, Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Ill , Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Iv, Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-V, Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Vl, Moc:Ni Hard Along With Their Weld Plugs , Separator Body Liner-Vil, Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Vlil, Moc: Ni Hard Along With Their Weld Plugs , Separator Body Liner-Lx, Moc: Ni Hard Along With Their Weld Plugs , Lower Skirt Carbon Steel, Moc: Carbon Steel ( 1 Set = 4 Nos.) , Bottom Mill Body Side Liners 1Mx1mx12mm, Moc: Ms(1 Set=3 Nos.) , Scrapper With Liner Plate Long, Moc:Is 1030, Gr-Ii, (Cast Steel) Moc Of Liner Iss 276 Astm Grade-3 , Scrapper With Liner Plate, Short, Moc:Is 1030, Gr-Ii, (Cast Steel)Moc Of Liner Iss 276 Astm Grade-3 , Complete Set Of Ventury For Coal Mills Hp-1103 , Set Of Classifier Blades Or Vane Of Deflector Door High Alloying Wear Resistance 55-62 Hrc With 4 Sets Of Ss Nut & Bolts With Each Plate ( 1 Set = 40 Blades) , Mpo Base Plate Liners Ni Hard Along With Their Weld Plugs , 28 Mill Discharge Valve Without Pnuematic Cylinder But With Gland Sealing Rope, Sliding Plate, Plate Guiding Nuts & Fasteners , Metallic Expansion Bellow/ Antiwear Ss 3-D Bellow Expansion Joint For Pf Piping, Specification: 2 Nos. Congulations, (Ss 304, Thickness Of Congulation-2Mm, Thickness Of Inner Sleeve-5 Mm), Medium: Coal+ Hot Air. Maximum Air Flow Per Mill:125 Tonne Per Hour. Pipe Od-710Mm, Thickness Of Connection End-16Mm (Mild Steel). Position Of Fitment: Vertical. , Metallic Expansion Bellow/ Antiwear Ss 3-D Bellow Expansion Joint For Pf Piping, Specification: 4 Nos. Congulations, (Ss 304, Thickness Of Congulation-2Mm, Thickness Of Inner Sleeve-5 Mm), Medium: Coal+ Hot Air. Maximum Air Flow Per Mill:125 Tonne Per Hour. Pipe Od-710Mm, Thickness Of Connection End-16Mm (Mild Steel). Position Of Fitment: Horizontal. , Dresser Coupling With Rubber For Center Feed Pipe Of Coal Mill , Erw Straight Pc Pipe With Id- 684 Mm Od-710 Mm Grade - Api 5L Low Alloy Steel Q345 , Wearable Adjustable Shrink (Adjustable Orifice) For Coal Mill Hp-1103, Coal Pipeod-710Mm, Model-Smk Type-B (Wearable Adjustable Shrinks To Be Supplied With 2 No. Extra Flange For Connection/Installation With Pc Pipe) , L-150 Coupling With Rubber Spider , Priming Valve For Lop Of Coal Mills , Seals Of Hot Shut Off Gate- L2000 Mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Seals Of Hot Shut Off Gate-L1800mm, Width 115Mm, Thickness-1.5Mm, Moc-Ss-304 , Link Rod For Hot Regulating Damper , Aluminum Cover For Hot Air Diaphragm, Moc- Al Sheet, 2Mm, Od-950Mm , Coal Mill Coupling Complete/Coupling K3741.18.0 Hp-1103 , Hexagonal Steel Set (Mill Coupling) Ss-304 , Taper Bolt With Washer & Nut Moc: Medium Carbon Steel, En8 , Seal Set Assembly For Gearbox Of Coal Mills Hp-1103 , Feeder Outlet Hopper Of Rc Feeder , Feeder Outlet Gate Without Actuator , Drive Sprocket Shaft For Feeder Outlet Gate , Gear For Feeder Outletgate , Rc Feeder Gearbox Helical Gear Small De, En 24 Bore Dia:25Mm,No. Of Teeth:26,Face Width:30Mm,Pitch Circle Diameter:57.182Mm, Keyway:8X3mm,Helix Angle:20Deg(Lh) , Rc Feeder Gear Box Helical Gear Nde, En 24 Bore Dia:43Mm,No. Of Teeth:76,Face Width:26Mm,Pitch Circle Diameter:159.68Mm, Keyway:12X3.5Mm,Helix Angle:20Deg(Rh) , Gear For Coc Gearbox De, Gst1661407, Bore Dia:16Mm,No. Of Teeth:21,Face Width:15Mm,Pitch Circle Diameter:34.90Mm, Keyway:5X2.5Mm,Helix Angle:20Deg(Lh), Moc: En-24 , Gear For Coc Gearbox Nde, Gst1661407, Bore Dia:25Mm,No. Of Teeth:80,Face Width:10Mm,Pitch Circle Diameter:128.6Mm, Keyway:6X3mm,Helix Angle:20Deg(Rh) , Moc: En 24 , Coc Gearbox Helical Gear Both End Set , Coc Chain Set (72 Chain Links & 10 Chain Scrappers), Moc: Ms , Cleanout Conveyor Chain Reducer Gear Box Shaft (Coc Reducer Gear Box Shaft) , Moc: En-27 With Heat Treatment , Coupling For Coc Of Rc Feeder , Idler Roller For Rc Feeder Model:Cs2036, 1 Set=12 Nos. , Weighing Roller For Rc Feeder And Coal Millgt1631107 , Tension Roller For Rc Feeder And Coal Millgt1653407 , Bearing Housing For Rc Feeder And Coal Mill Gt1651907 , Eccentric Bearing Housing For Rc Feeder And Coal Mill , Bearing Housing Left For Rc Feeder Model: Cs2036gt1630407 , Bearing Housing Right For Rc Feeder Model: Cs2036gt1630607 , Bearing Housing Assembly & Rode Housing Assembly For Rc Feeder And Coal Millgt1632107 , Take Up Pulley For Rc Feeder Model: Cs2024, Cs2036gt1650307 , Bushing For Rc Feeder , Part Number:Gt1651807 , Take Up Pulley Shaft For Rc Feeder , Pyrite Chute/ Tramp Iron Spoute For Coal Mill Before Pv1, Moc: Ms, Thickness 16 Mm , Collar Of Ventury Outlet Of Coal Mill Hp-1103 , Moc: Carbon Steel , Flange For Hot Air Diaphragm , Wear Resistant Weld Overlay Plate With Carbide Layer Of 6Mm For Coal Mill, Carbide Layer On Inner Side Of Curved Portion Dimensions-Height:1500Mm, Width-1000Mm, Thickness-10Mm (1 Set= 6 Nos.) , Vane Wheel Segment For Coal Mill ( Hp- 1103) ( 1Set = 08 No.)