Tender For Balance Work Of 02 Nos. Type Iii Residence At District Jail Kanpur Dehat (U.P.), 1 Balance Work of 02 Nos. Type III Residence at District Jail Kanpur Dehat (U.P.) 2 Wiring points for light with 1.5 sqmm.FR PVC insulated multistrand singlecorecoppercondutorcableinPVCconduit pipepartly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire,piano type switch & ceilingrose/angle/battenholderon3mmthickphenolicpaminated backalitesheetetc.completeinallrespects.asdirectedincludingmatching colour wash. 3 Wiringpointsfortwowaylightwith1.5sqmm.FRPVCinsulated multistrand single core copper condutor cable in PVC conduitpipe partlyconcealedinthewallandpartlylaidinslabalongwiththe reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulatedmultistrandcopperearthcontunitywireandtwonumber twowaypianotypeswitches&ceilingrose/angle/battenholderon 3mmthickphenolicpaminatedbackalitesheetetc.completeinall respects.as directed including matching colour wash. 4 Wiring points for Fan /Fresh air fan (light duty exhaust fan )with 1.5 sqmm.FRPVCinsulatedmultistrandsinglecorecoppercondutor cableinPVCconduit pipepartlyconcealedinthewallandpartly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire,piano type switch & ceiling rose on 3mm thick phenolicpaminatedbackalitesheetetc.completeinallrespects.asdirected including matching colour wash. 5 Wiring points for Plug with 1.5 sqmm.FR PVC insulated multistrand singlecorecoppercondutorcableinPVCconduit pipepartly concealed in the wall and partly laid in slab along with the reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulated multistrand copper earth contunity wire,piano type switch & socket sheetetc.complete inallrespects.asdirectedincludingmatching colour wash. 6 Wiring points for Call bell with 1.5 sqmm.FR PVC insulated multistrand single core copper condutor cable in PVC conduitpipe partlyconcealedinthewallandpartlylaidinslabalongwiththe reinforcement before concreting, complete with 1.5 sq. mm. FR PVC insulatedmultistrandcopperearthcontunitywire,pianotypebell push or 2pin socket etc.complete in all respects.as directedincluding matching colour wash. 7 Supply&wiringofsubmainswith2nos.2.5sq.mm&with1no. earth wire of 1.5 sq.mm FR PVC insulated 1100 V grade single core multistrandcopperconductorcablein PVCconduit pipepartly concealedincludingsupplyofallmaterial,labourandT&Petc. required for proper completion of the work as directed by Engineer I/C. 8 Supply andwiringofsubmainwithtwonumber4sqmm . FR PVC insulated 1100 V grade multistranded single core copper conductor cablein 20mmdiaheavyduty(2mmthick)PVCconduit partly concealedinwallandpartlylaidinslabalongwithreinforcement beforconcretingwithonenumber2.5SqmmFRPVCMultistand copper earth contunity wire including colour wash etc. complete in allrespects. 9 Supply and wiring of submain 2 number 6 sqmm . FR PVC insulated 1100Vgrademultistrandedsinglecorecopperconductorcablein 20mm dia heavy duty (2mm thick ) PVC conduit partly concealed in wall and partly laid in slab along with reinforcement befor concreting withonenumber4.0SqmmFRPVCMultistandcopper earthcontunity wire including colour wash etc. complete in all respects. 10 Supplyandwiringofsubmainwith4number10sqmm.FRPVC insulated 1100 V grade multistranded single core copper conductor cablein 32mmdiaheavyduty(2mmthick)PVCconduit partly concealedinwallandpartlylaidinslabalongwithreinforcement beforconcretingwithtwonumber10SWGcopperearthcontunitywire including colour wash etc. complete in all respects. 11 S/Fofhexagonalfanboxwithhexagonalsideofapprox80mmin lengthfabricatedfrom16SWG MS. Sheet incorporating10mm dia,M.S. round bar duly bent for supporting fan hanger dully painted with redoxide andscrewing arrangementwith wiringconduit laid in theR.C.Croofbeforeconcretingalongwithsupplyofall materials,labour.T&Petc.requiredforpropercompletionofthework. 12 Supply&fixingofsinglewallbracket onmatchingM.D.F.E.G.boardbase etc. complete in all required. 13 Supply and fixing of LED Tube Light batten fitting suitable for up to 1X 22 watt LED tube light on surface complete in all respect. 14 Supply and Fixing of LED Tube Light with batten suitable for up to 1X22wattLEDtubelightcompleteincludingtubeetc.onsurface complete in all respect. 1 X 22 W 15 Supply of Ceilling Fans with fan motor of A.C. Permanent insulation, capacitorratingconformingBEE5starratingandIS:374/79abd alsocomplywithIS:1709/1984withlatestamendment.Therate voltage220/240volts,50Hz,1-phACthefanassembleshould consistofdownrodblades,shacklecanopiesetcandwith double ball bearing system. 16 Supplyfixingofelectronic fan regulator (Modular) 120-280 V. ISI marked,ontheexistingswitchboardincludingmakingconnetion, required material, labour T/P etc for proper completion of work to thesatisfaction of Engineer in charge of work. 17 Supply & erection ofA.C 230/250 Volts,50 Hz exhaust fans including providingm.S bolts,mountingframeand other acessories including connections etc.complete as required300mm sweep as perdirectionof E/I Makebajaj,Cromption or Equivalent. 18 Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve 6 - 32 amps. 19 Supply and fixing of 40/63 Amp MCB(10KA)C Curve 40 Amp. 4 Pole MCB 20 Supply and fixing of 40/63 Amp MCB(10KA)C Curve 63 Amp. 4 Pole MCB C CurvE 21 Supply and fixing of flush/surface mounting distribution boardswithadditional metal door without MCBcomplete in all respects. 4 Way TPN 22 Supply and fixing of flush/surface mounting distribution boardswithadditional metal door without MCBcomplete in all respects. 6 Way TPN 23 Supplyandfixingofpowerplugwith15Amp./250Voltflushtype universalswitchand5pin15A/250V flushtypeuniversal socket switch on concealed M.S. box including supply of all material, labour T&P etc. required for proper completion of work. 24 Supply & fixing of SheetSteelEnclosureSurface/FlushMounting fitted With 20/32 Amp. 2Pin and earth metal clad scraping earth plug and socket complete in allrespects as per direction and satisfactionof engineer-in-charge.-Cat. A 25 Supply and fixing of 63 A 415 V metal clad TPN CFS complete withHRC fuse etc. on angle iron frame complete in all respect . 26 Supply and burying of 600mm x 600 mmx6mm G.I. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm G.I.pipe and funnel for watering and two earthing leads ofNo.8to10SWGG.I.wirein15mmdiaG.I.pipeuptoswitchboard (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mmthick alround etc. complete in all respects. 27 Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose asrequired complete in all respects. 28 Supply & fixing of two number 8 SWG G.I. wire for earthing purposeas required complete in all respects. 29 Supply,installation,testingandcommissioningofelectricalpane, modular type, front accessible only, free floor standing confirming to Minimum IP:43 degree of protection.The panel sheet structure shall undergoseventankpre-treatmentprocessbeforepainting. The sheetsteelshallbeallof2.2mmthickCRCAsheet. Allthe openable compartmentsof the panel shall be completely shrouded andprovidedwithpadlockingarrangementonallcompartments including bus bar and cable alley chambers.The panel height shall notexceed2200mmandthemaximumoperatingheightforany switchgearshallnotbemorethan1700mm. Thepanelshallbe providedwithminimum75mmbasechannelframefabricatedfrom ISMC sections.All bus bar links in the panel shall be solid bus bars with coloured PVC shrinkable sleeves, no wires will be acceptable. Continuous earth bus shall run alround the panel with earthing studs providedat minimum2places. Thecontrolwiringshallbecarried out with minimum 1.5/2.5 sqmm copper wirefter t adequate number of NO/NC, potential free contacts incorporated for remoteoperationofthestarters. Propersizedcabletermination glandplatesshallbeprovidedon cablealleysandknockoutsfor sameshallbeprovidedduringfabricationstageitself. Thepanel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions.A 5A socket service outlet (single phase) shall be provided in one of the compartmentsaserviceoutletinthepanel. Panelshallbeso designed at to have minimum 20% spare feeders/space.Panel shall undergo epoxy powder coated paint, colour as per IS:5 requirement. Allcableterminationsshallbefrom top. The completepanel shall be fuse less type, for control circuits 2A/6A MCBs to be used. All bus bars shall be of aluminium, electrolytic grade only.Maximum designdensity shallnot exceed1Amps/Sqmm. Allbusbars shall be insulated with coloured heat shrinkable PVC sleeved.All bus bar supports shall be non hygroscopic DMC/SMC supports. The panel shall be manufactured in conformance to requirements of local electrical inspector and it shall be contractors responsibility to get initial approvalof drawingsand alsofinal approvalof complete electrical works related to this section. 30 The minimum clearances between bus bars shall be as follows : 31 Phase to phase - minimum 20mm 32 Phase to neutral-minimum 15mm 33 Main L.T.Panel 34 Incoming : 35 One (1) No 200A 4 pole MCCB 36 Metering : 37 One(1) No.(0-500V)96x 96Sqmmvoltmeterwith controlfuse &selector switch. 38 One(1)No.(0-200A)96x96SqmmCToperatedAmmeterwithselector switch, CTs etc. 39 One (1) Set of Phase Indication Lamp. 40 Bus Bar : 41 One (1) No.200 A, TPN aluminimum bus bar of suitable length. 42 Outgoing : 43 Phase indication lamps on each outgoing to be provided. 44 100Amps TPN-2 Nos 45 Outgoing : 46 63 AMP TNP-2 NOS. 47 OR outgoing as per site requirment 48 S/Fof100mmdiaG.IpipeBclassforcablecompletedwith supports by 3 nos. clamp made for 20x30 mm MS flat and suitable size of nutbolt & washer required for proper completion of worh asper direction of E/I. 49 Providingandfixingwaterclosetsquattingpan(IndiantypeW.C. pan) with 100mm sand cast iron P or S trap, 10 litre low levelwhiteP.V.C.flushingcisternwithmanuallycontrolled device (handle lever) conforming to IS : 7231, with all fitting and fixtures completed including cutting and making good the walls and floors wherever required. White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests 50 Providing&fixingwhiteviterouschinawashbasinwithC.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste ofstandard pattern,includingpaintingoffittingandbrackets, cutting & making good the walls wherever required . Flat back Wash Basin size 550X400 mm with single 15mm C. P. brass pillar tap 51 Providing & fixing stainless steel AISI 304 (18/8) kitchen sink withdrainboardasperIS:13983withC.I.brackets and stainlesssteelplug40mmincludingpaintingoffittingsand brackets cutting and making good the walls wherever required. 510x1040 mm bowl depth 200 mm 52 Providing&Fixing600X450mmbevellededgemirrorof superior glass(ofapprovedquality)completewith6mmthick hardboardgroundfixedtowoodencleatswithC.P.brass screws and washers complete. 53 ProvidingandfixingPTMTtowelrailcompletewithbrackets fixedtowoodencleatswithCPbrassscrewswithconcealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms 54 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore 55 Providing & fixing soil, waste and vent pipes. a) 100mm dia centrifugally cast iron S & S pipe. 56 Providing & fixing soil, waste and vent pipes. b)75mm dia centrifugally cast iron S & S pipe. 57 ProvidingleadCaulkedjointstosandcastiron/centrifugally cast (spun) iron pipes & fittings of diameters. 100 mm 58 ProvidingleadCaulkedjointstosandcastiron/centrifugally cast (spun) iron pipes & fittings of diameters. 75 mm 59 Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4mix(1cement:2coarse:4gradedstoneaggregate 20mmnominalsize).Includingcost of cutting holes& making good the walls etc. a) for 100mm dia pipe. 60 Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4mix(1cement:2coarse:4gradedstoneaggregate 20mmnominalsize).Includingcost of cutting holes& making good the walls etc. b) for 75mm dia pipe. 61 Providing & fixingcast iron coller. a) 100mm dia. 62 Providing & fixingcast iron coller. b)75mm dia. 63 Providing and fixing trap of selfcleansing designwith screwed downorhingedgratingwithorwithoutventarmcomplete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet : Sand cast iron S&S as per IS - 3989 110mm dia 64 Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. a) 100mm 65 Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. b) 75mm 66 Providingandfixingcentrifugalycastironsingleequalplain junction of required degree. 100x100x100mm 67 Providingandfixingcentrifugalycastironsingleequalplain junction of required degree. 75x75x75mm 68 Providing and fixingcast iron terminal guard. 100 mm 69 Providing and fixingcast iron terminal guard. 75 mm 70 ProvidingandfixingonwallfaceunplasticisedRigidPVCrain water pipes conforming to IS : 13592 Type A, including jointing withsealringconformingtoIS :5382, leaving10mmgapfor thermal expansion, (i) Single socketed pipes. 71 Providingandfixing GIpipescompletewithGIfittings andclamps,includingcuttingandmakinggoodwallsetc. (internal work).Internal work-Exposed on wall15mm dia nominal bore 72 Providingandfixing GIpipescompletewithGIfittings andclamps,includingcuttingandmakinggoodwallsetc. (internal work).Internal work-Exposed on wall25mm dia nominal bore 73 Providingandfixing GIpipescompletewithGIfittings andclamps,includingcuttingandmakinggoodwallsetc. (internal work).Internal work-Exposed on wall32mm dia nominal bore 74 PaintingGIpipesandfittingswithSYNTHETICenamelpaint overareadymixedprimingcoat,bothofapprovedqualityfor new work. 32mm dia nominal bore 75 Concealedpipeincludingpaintingwithanticorrosivebitumatic paint, cutting chases and making good the wall.(internal work) Exposed on wall a) 15mm dia nominal outer dia pipes 76 Concealedpipeincludingpaintingwithanticorrosivebitumatic paint, cutting chases and making good the wall.(internal work) Exposed on wall B) 20mm dia nominal outer dia pipes 77 Providing&fixinggunmetalgatevalvewithC.I.wheelof approvedquality (screwed end) 25 mm nominal bore 78 Providing&fixinggunmetalgatevalvewithC.I.wheelof approvedquality (screwed end) 32 mm nominal bore 79 Providing and fixing 15 mm nominal bore C.P brass long nose bib cock of approved qualityconforming to IS standardsand weighing notlessthan 810 gms. 80 Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conformingto IS8931. 81 Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable lockingarrangementandmaking necessary holesforinlet, outlet and overflow pipes but without fittingandbasesupport for tank. 1000 litres capacity 82 Excavating trenches in all kind of soil of required width for pipes, cablesetc.includingexcavationforsocketsanddressingof sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, inlayersnotexceeding20cmindepthincludingconsolidating eachdepositedlayerbyramming,watering,etc&disposigof surplus excavated soil as directed within a lead of 50m. a) Pipes 80mm to 300mm diameter. 83 Providing, laying and joining glazed stone ware pipes grade A withstiffmixtureofcementmortarintheproportionof1:1(1 cement : 1 fine sand) including testing of joints etc. complete. 100 mm diameter 84 Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. 100 mm diameter 85 Constructingbrickmasonrymanholeincementmortar1:4(1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundationconcrete1:4:8mix(1cement:4coarsesand:8 gradedstoneaggregate40mmnominalsize)insideplastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels incementconcrete1:2:4(1cement:2coarsesand:4graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With FPS bricks of class designation 75 (i) For Sewer Line 86 Providing and fixing square mouthS. W. Gully trapgrade `A complete with C.I. gratingbrickmasonry chamber with F.P.S bricks and water tight CI cover with frame of 300 x 300 mm size (inside)theweightofcovertobenotlessthan4.50kgand frame to be not less than 2.70 kg as per standard design 180 x 150 mm. size P type 87 G.S.T. Extra as per applicable
