|
| 1 | Item rate |
| 2 | Providing and fixing flamed finish Sadarahalli grey /Red/Raw Silk/an Brown/Kashmir Yellow/ Ikon Brown/ Multi Red/ Blue Pearl/Jet Black granite stone (bull nosed at Plaza edges) of size 1200x600x30 mmfor Plaza Floor,using 5mm thick approved thick bed adhesive as per specification over prepared base on 20mm (average) thick base of cement mortar in 1:4 (1 cement : 4 total aggregate- sand and 10mm single sized aggregate) using 43 grade cement, water reducing admixture as per ISO 9103:1999 and jointing with white cement with matching colour pigment all complete in levelling course laid to proper slopes over screed base including, base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawing and directions of engineer-in-charge.All Light color Granites to be fixed on White Cement.As per Approved Adhesive..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over. |
| 3 | Providing and laying 25mm thick and minimum 1200mm long Sadarahalli flamed finished granite on approx. 300mm wide tread on stairs with and including nosing and 2 Nos. 6x6 anti-slip grooves filled with carborandum powder mixed with Araldite or equal adhesives. (Colour of granite as approved by Engineer) all laid over base cement mortar 1:4, up to 30mm thick with ordinary Portland Cement, fit jointed with/ without groove, with white cement slurry mixed with pigment to match shade of granite including all finishing, all as required, as per specifications and drawings and as directed complete. |
| 4 | Design, supply and installation of Terra Cotta clay tiles NBK,Argeton, Agrob Buchtal or equivalent, 28 mm thickness (Length: max. 1200 mm, Height: 300 mm), back ventilated, with self-draining open joint system in approved color, finish, texture, sizes and profiles. Tiles must have customized enamel based high gloss finish as approved for the project requirement. It shall be double-leaf construction and have labyrinth top and bottom returns to prevent easy water excess behind tiles. The tiles shall be fixed on aluminum support system which includes adjustable aluminumbrackets,heavy duty self standing aluminum tubular studs and frames , extruded aluminum vertical carrier tracks with gaskets, tile clips, and fastening devices for Terra Cotta clay tile elements. Terra Cotta tiles must be removable, without breakage or disruption to adjacent tiles. Tile clips must be concealed and the design system must accommodate thermal movement. Stainless steel screws and metal devices (aluminum support system) attached to steel aupporting structure shall transmit imposed loads from the Terra cotta system to steel support strcuture. |
| 5 | Providing and laying 20mm thick mirror polished Granite Stone in Risers of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in-charge) over 12 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and relevant drawings.All Light color Granites to be fixed on White Cement.As per Approved Adhesive..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over. |
| 6 | Providing & Fixing Polished Granite Coping, bull-nosed over 20 mm thick cement mortar 1:4(1 cement: 4coarse sand) with joint treated with white cement mixed with matching pigment including Rubbing, Curing , Moulding & polishing to edge to give high gloss finish etc. complete.Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124.The flooring shall be covered with POP / Gypsum powder of 12mm thick /Plywood to ensure that the flooring is not damaged till the construction work is completed and handed over. |
| 7 | Providing and laying 65mm polished Red/Raw silk/Black/Tan brown/Blue pearl granite slabs for trench cover with 25mm dia holes @ 75mm c/c spacing complete..Minimum Compressive strength shall be as per IS 1121(part 1) .Water absorption Test shall be carried out as per IS 1124 |
| 8 | Providing and laying 12mm (minimum)thick with 3mm(minimum)thick projection on surface yellow coloured directional vitrified porcelain tactile tile of pelican or equivalent(as per specification)laid on floor with laterite 111 crete filler powder mixed with laterite 73 latex admix and applied to a minimum thickness of 4.5mm(The mixing ratio shall be as follows:20kg bag (laterite 111):5.5 liter (Laterite 73).Spacer of 3mm shall be used between the tiles and joints filled using Laterite Latapoxy SP-100 epoxy grout in Inca Gold colour. The joint depth shall be 6mm.Laticrete product shall be as manufactured by Laterite India Pvt.ltd/Laterite International Inc.)over 20mm thick bed of cement mortar 1:4(1 cement:4 coarse sand) in levelling course laid to proper slopes over screed base including base preparation including movement joint in screed as per specification with 10mm thick compressible filler to edge of screed with two parts polysulphide sealant to top edge as per approved drawings and directions of engineer-in-charge.300X300mm for hazard warning and directional tactile tiles as per approveddrawings |
| 9 | Providing & fixing Toilet Cubicle (of following standard dimension which includes 900mm door size width) made of heat, bacteria, water,chemical,scratch, impact and anti bacterial resistant 12mm thick solid compact laminate panels tested in approved laboratory. Finish of the compact laminate should be Suede, Raw silk model includes doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of stainless steel (Grade 304) as per manufacturers specifications & Architects instructions like (1)Door knob(2)Gravity hinges(3)Thumb turn lockset with occupancy indicators(4)Coat hooks with Door stopper(5)U-channels(6)Adjustable foot/pedestal(7)Top rail with corner connector(8) Rubber noise deafening tape(9)Screws & wall plugs. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel bottom cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height up to 150mm. the top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the SS top rail. Toilet Cubicle with standard dimension of 2025mm Height x 1000mm width x 1550mm Depth, which includes up to 900mm door size width) |
| 10 | Providing , Fabricating, Polishing & Erection of Required Height, Shape and Designing Comprising of 2 mm thick SS Grade 304 Sheet Cladding Over Circular and Rectangular shape,RCC/Steel Column on Aluminum Base frame of 25x35x5mm and 5mm thk & 450 mm width Perforated (6mm perforations @ 12mm c/c) SS Grade 304 Matte Finished Sheet fixed on Frame 2 nos of 50 mm SS Grade 304 Dia Concentric Pipe, Bracing of 2 rings with 12 nos of 50 mm SS Grade 304 Dia pipe fixed on to the RCC /SteelColumn with 3 nos. of 20 mm thick Arched shape Plate to support the Frame As / Drawing (for payment purpose only SS item shall be measured. Aluminum base frame shall be paid extra) |
| 11 | Providing,fabricating and erectingmatte finish grade 304 SS sump/Chamber covers of size 600mmX600mm suitably supported & fixed over MS frame along with granite stone matching with relevant floor finish, lifting hooks/keys etc. complete as per relevant architectural drawing. |
| 12 | Providing & installation of approved quality vertical linear baffle ceiling made out of folded Aluminum. The baffle units shall be in size of 50mm (W) x 150mm (H) and 1000mm x 4500mm x 1mm (thk), non perforated. The ceiling baffle units shall be installed at a distance of 300mm c/c in one direction. The baffle units shall be attached to C-channel carriers spaced at 1200mm c/c. The C- channel carriers shall then be cross connected to perforated L-angle primary grid and suspended with M6 threaded rod hangers spaced at 1200mm and pertaining to Class A Fire Rated, as per ASTM E-84 |
| 13 | Providing and installation of 6mm thick transculent Acryalic sheet with 8mm thick MDF board design of approved shape & size preparation and installation shall be carried out as per manufacturer\"s specifications and instructions,including lazer cutting design of mdf,required adhesive and chemical solutions,fasteners and fixtures,scaffolding etc complete. |
| 14 | Providing and painting Spray Finish Exterior Quality Duco paint of approved shade, on new work ( Metal and Steel ) two or more coats, to given an even shade, including one coat of primer, preparation of surface using automotive putty, thinners etc. surface duly emery papered to give a perfectly smooth and even prepared surface before painting etc. complete |
| 15 | Providing and fixing heavy Duty Stainless steel Fixed base Bollards Outer dia 160mm,wll thickness 5mm and height above finish floor 950mm and en=mbeded height below floor 300 mm in concrete. The installation shall be carried out as per manufacturer\"s instructions and specifications. |
| 16 | Providing and Fixing Stainless Steel 304 Roof Gutter with wall thickness 3mm,width up to 300 mm and depth up to 300mm including SS collar,ss-spouts 150 mm diameer,the joints shall be ss welded,including reqired,fixtures,fasteners,sealent,scaffolding etcc complete. |
| 17 | Providing and fixing full height stainless steel chain 316 grade as downtake for rain water from Roof Gutter Bottom up to Ground Floor iincluding cutting and fixing,fixtures,fasteners,clamps ,scaffolding etc complete. ( Weight of Chain 2 Kg / Rmt ) |
| 18 | Providing and fixing PIR/Puf Panel having thickness 50mm with Top Sheet 0.5mm thick and bottom sheet 0.5mm thick ( TCT ),including PVDF Coated galvalume steel coil with necessary metal self tapping screw of Hilti Make,washers,sealent,mastic tapes,required Flashings,ridges,end trims or end flashings,corners and scaffolding,cranes,hydra,boom lift etc complete. Installation shall be carried out as per manufacturer\"s instructions and specifications. ( Make : Jindal or equavalent with ISI mark ). Detail Shop Drawings shall be submitted by Installers to Architect for approval prior installation. |
| 19 | Providing and constructing Ashlar Laterite Stone masonry in superstructure in C.M 1:4 including manual cutsmooth dressing of all sides of latrite block (size 14 x 10 x 8 inch),Joint width shall be 3mm only, stricking and racking out joints,scaffolding,curing,cleaning etc complete. |
| 20 | Providing and laying sand blasted or rough surfaced Ruby red, jet black, Hasan green granite stone tiles 25 mm to 30 mmthick of an approved quality and size forpaving / flooring including cement mortar bedding of 25 mmthick in 1:4 proportion, cement float, pointing in cement mortar 1:3, cutting, dressing, leveling,jointing, pointing, curing, finishing etc complete asdirected by EngineerIn Charge. |
| 21 | Providing & fixing anti climb fence system with mesh vertical wire dia 6mm,horizontal dia 4mm, mesh size 76mmx12mm panel height 2.15m & post height 2.2m & post section 100 mm dia& 4mm wall thickness with base plate and Chemical Anchor Fasteners 16mm diameter 200mm long four numbers at every 2m interval & hard rubber top cap at top of every steel Post,the steel wire mesh &the vertical posts & cornar posts,strutsshall be hot deep galvanized with polyster power coating RAL 6005 including all necessary fixtures & fastenings. Note : The wire mesh shall be fully tightened . Mode of measurement : Campus outer side face area of the Mesh.( Height of the mesh x entire length of the fence only.). Supply shall be carried out after verificaion & approval of the samples by Engineer incharge. |
