Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-08-2024 | Due Date Extended for tenders closing on 29-07-2024 | Admin Corrigendum Date Extend | 04-09-2024 |
| 2 | 19-07-2024 | Revised BOQ and other Corrigendum | BOQ | 29-07-2024 |
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed. |
| 2 | M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 3 | M&L for providing reinforced cement concrete(1:2:4) type B-1 using 20 mm graded crushedstone aggregate as in kitchen slab, shelves and manhole cover etc. |
| 4 | M&L for providing reinforced cement concrete(1:2:4) type B-1 using 20 mm graded crushedstone aggregate as in Chajjas complete all as specified and directed. |
| 5 | M&L for providing reinforced cement concrete(1:2:4) type B-1 using 20 mm graded crushedstone aggregate as inBeams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and directed. |
| 6 | Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish flat surface of concrete (the thickness of slab/shelves n.exc.100 mm) complete all as specified and directed. |
| 7 | Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finish flat surface complete all as specified and directed. |
| 8 | Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side MOD land, complete all as specified and directed. |
| 9 | M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length. 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed. |
| 10 | M&L for 75mm thick cement concrete (1:4:8)type D-2,using 40mm graded stone aggregate as in sub base complete all as specified and directed. |
| 11 | M&L Cement concrete1:2:4 type B0(using 12.5mm graded crushedstone agg) asin roof leveling, finished even and fair, complete all as specified and directed |
| 12 | M&L for PCC (1:2:4) Ty B-0 using 12.5mm thick course aggregate as incills, steps, parapets,, copings, andthe like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 13 | M & L 100mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate), as in sub base complete all as specified and directed. |
| 14 | M&L for 75mm thick PCC (1:4:8) ty D-2 using 40mm graded stone aggregates as in levelling course below floor tiles in bathroom and WC complete all as specified and directed. |
| 15 | Demolition of brick work built in cement mortar in any description and position complete all as specified and directed. |
| 16 | M & L brick work with sub class \"B\" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed. |
| 17 | M&L for Brick work with sub clas \"B\" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 completeall as specified and directed. |
| 18 | Dismantling of Cast Iron pipe/PVC pipeup to 100 mm bore complete all as specified and directed. |
| 19 | Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipeup to 150 mm bore complete all as specifiedand directed. |
| 20 | S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/fixtures and clamps out of 50mm x 5 mm flat iron includingbolts and nuts and securing ends of stays to walls or rooffixed on wall or in trenches or in floor complete all as specified and directed. |
| 21 | All as per item No. 20 above but 75mm nominal outside diameter complete all as specified and directed. |
| 22 | S& F PVC (SWR) vent cowl suitable for 75 mm pipe complete all as specified and directed. |
| 23 | S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed |
| 24 | All as per item No. 23 above but 75 mm bore. |
| 25 | S&F in repair PVC (SWR) floor trap/Nahani trap, 75mm dia plain including jointing with solvent cementwith grating includingjointing to waste pipein cement concrete complete all as specified and directed. |
| 26 | S&F in repair PVC branch piece single (equal or unequal) 110 mm bore ordinary or inverted (spigot or sockettype) or with parallel branches incl access door acomplete all as specified and directed |
| 27 | S&F PVC (SWR) reducers 110mm dia, complete all as specified and directed. |
| 28 | M&L for Anti termite Treatment (ATT)the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed. |
| 29 | S&F for PVC (SWR) branch piece, double (double Y) equal or unequal of 75 mm dia complete all as specified and directed. |
| 30 | S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed. |
| 31 | S&F PVC (SWR) 75mm dia (Single T) or unequal provided with access door complete all as specified and directed. |
| 32 | Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed. |
| 33 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed. |
| 34 | M&L Non - skid coloured ceramic glazed rectified tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified anddirected |
| 35 | M&L Coloured ceramic rectifiedtiles 300x600 x 7 to 8mm thick,as in vertical surfaces of wall suchas dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 completeall as specified. |
| 36 | S&Fjoint free non skidceramic tiles coloured of7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed inneat cement slurry and pointed with whiteor coloured cement over and including 15mm thick screed bed in cement mortar 1:6complete all as specified and directed. |
| 37 | All as per item No 36 above but as in skirting over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 38 | M&L for 16-18 mm thick mirror polished Machine cut kota single piece stone slab of size 22\"\"x22\"\" for flooringover cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slablaid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 39 | M&L kota stone mirror polished slab with uniform texture of 16-18 mm thick in trader of steps (to be flushed and provided with three Nos of grooves at the end on each step), riser of steps, skirting, dado and pillarsin one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing andpolishing, bevelled edge of corner etc complete all as specified and directed. |
| 40 | M&Lfor18to20mmthickUdaipurgreenStonefactorymadebullnosed, polished (table rubbed and polished) as injambs, window cills, cookingplatform and the like etc in cement mortar 1:4 including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 including rounding of edges, making hole for gas pipe complete all as specified and directed. |
| 41 | M&L for cleaning of concrete or plasteredsurfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followedevenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thick APP modified polymeric waterproofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weightnot less than160 GmperSqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm asper manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat ofbituminous aluminum paint @ 0.20 kg per Sqm as per manufacturer’s instructions over, complete all as specified & directed. (including removal of existing membrane and removal of scrape from site) |
| 42 | Taking down chowkhat or frames exc.1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed. |
| 43 | Taking down chowkhat or frames not exc. 1.5 Sqmeachwith shutters (without taking off shutters from frames) complete all as specified and directed. |
| 44 | Supply & fixing pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 45 | Supply & fixing pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 105x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 46 | S&F 35mm thick Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified & directed. |
| 47 | S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed. |
| 48 | M&L for built in steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm th with pressed steel shutter 1mm thk Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including ms hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of ms peg set of 3 pegs including spray including locking arrangement painting with two coats of synthetic enamel paint over one coat of red oxide primer with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surface of frame & shutter and making good disturbed portion in cm 1:3 or PCC 1:2:4 complete all as specified & directed. |
| 49 | S&F factory madegauged shutter shall be made outofangle iron 35x35x5mm (outer frame) and 25x25x5mm (middle rail 2 nos, 150 mm apart from each other) and 1.0mm thick steel sheet covering on middle rail, 10mm Square bars @ 100mm C/C fixed vertical as grillcompletewithstainlesssteelflyproof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide as shown on drawing complete all as specified & directed. |
| 50 | S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing offittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 Complete all as specified by the manufacturer complete all as specified & directed.. |
| 51 | S&FFRP doorframesthreelegged of cross section 90x45mm having single rebate 32mmx15mm.The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mmthick, frame shall be covered with fiberglass from all sidesmsflatiron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed. |
| 52 | S&F 100 mm long(size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed. |
| 53 | All as per item No. 52 above but 75 mm long. |
| 54 | S&F 300mm long, stainless steel of AISI 304 grade,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed. |
| 55 | S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed. |
| 56 | All as per item No. 55 above but 75 mm long. |
| 57 | S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm size long complete all as specified and directed. |
| 58 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed. |
| 59 | M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 60 | M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 61 | M&L for powder coated aluminiumanodised window sliding type (3shutters type) with sash bars, aluminium sections weighing 0.55 Kg/m (min) including stainless steel wire mesh, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame complete all as specified & directed. |
| 62 | M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, including S&F 3 to 4 mm thick pin headed glass complete all as specified and directed. |
| 63 | S&F stainless steel (grade-304) grills made of hollow tubes section including welding, grinding, buffing polishing and making curvatures wherever required and fitting the same with necessary holdfasts/ SS dash fastners with nut & bolts of required size, complete all as specified and directed. |
| 64 | S & F 18 mm thick with min density 600 Kg / Cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. |
| 65 | S & F 18 mm thick with min density 600 Kg / cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s instructions complete all as specified and directed. |
| 66 | S & F 6 mm thick with min density 600 Kg / cum LEAD FREE PVC celuka ply fixed with ss screws and solvent cement / adhesive to make wall mount kitchen cabinet back sides complete as per manufacturer’s specifications complete all as specified and directed. |
| 67 | S&F Auto hinges for cabinet case complete all as specified and directed. |
| 68 | S&F 100 mm size stainless steel bright finish handle for cabinet shutter complete all as specified and directed. |
| 69 | S &F for PVC (SWR) branch piece, double (double Y) equal or unequal of 110 mm dia complete all as specified & directed. |
| 70 | Taking down cement plaster, terrazzo dado in any thickness from brick or stonewalls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed. |
| 71 | M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed. |
| 72 | M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed. |
| 73 | M&L Rendering 5 mm thick in cement mortar 1:4 over a layer of 10mm thick rendering in cement mortar 1:6 on fair face of brick work/ concrete surfaces of wall with water proofing admixture finished even and smooth without using extra cement complete all as specified and directed. (WPC will be measured and paid separatly) |
| 74 | Supply only liquid water proofing compound complete all as specified and directed. |
| 75 | Preparation of new plastered surface or old treated surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsiondistemper using roller for painting complete all as specified & directed. |
| 76 | M& L preparing plastered new surfaces of ceiling and applying three coats of white wash on ceiling surface complete all as specified & directed. |
| 77 | S & F for PVC (SWR) couplers of dia 110 mm complete all as specified & directed. |
| 78 | S&F in repair PVC branch piece single (equal or unequal) 75 mm bore ordinary or inverted (spigot or sockettype) or with parallel branches inclaccess door complete all as specified and directed |
| 79 | Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed. |
| 80 | All as per item No. 79 above but 20 mm bore |
| 81 | S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling or laid in floors etc complete all as specified and directed. |
| 82 | All as per item No 81 above but 20 mm bore. |
| 83 | M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed. |
| 84 | Dismantling of RCC/ PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed. |
| 85 | S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings complete all as specified and as directed. |
| 86 | S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed. |
| 87 | S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight210 gms) complete all as specified and directed. |
| 88 | S&F in repair vitreous chinaware white wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed. |
| 89 | S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and floatincluding brackets and flush pipe complete all as specified and directed. |
| 90 | S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 91 | S&F in repairstainless steelsink AISI 316 grade without drainage board of 1 mm thickwith plug, washer and waste, including bedding in cement mortar to dwarf wall or including CP Waste, PVC Down pipe etc andfixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowlsize 410mm x 330mm x 160mm or more complete all as specified & directed. |
| 92 | S&F in repair Chromium platedtubular towel rail, 25mm dia, ‘D’ type 60cm long between flanges of brass chromium platedand with hooks,brackets & End caps fixed with brass screws complete all as specified and directed. |
| 93 | Supply & fix wall mixer chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm borepipes complete all as specified and directed. (Make Jaquar Florentine FLR-CHR-5273 UPR, Pearl GPR-884, CERA-F1017401) |
| 94 | S&FinrepairBrasschromiumplatedshowerrose 125mmsizeallasspecifiedanddirected (make: Jaquar/cera/pearl or equivalent) |
| 95 | S&F in repair Looking mirror 600 x 450 mm beveled edge 5.5 mm thick selected quality glass, mounted on 6 mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washerscomplete all as specified anddirected. |
| 96 | S&F in repair Stainless steel cromium plated Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 97 | S&F in repairs 15mm bore Pillar tap of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed. |
| 98 | Supply and fix glass corner shelf fancy type made of 6 to 7 mm thick sheet glass of size 250mmx250mm fixed with chromium plated brackets complete all as specified and directed. |
| 99 | S&FStainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate,& cutlery stand of size 18x24 inches , fixed to wall plugs andchromium plated brass screws complete all as specified and directed. |
| 100 | S & F in repairs vitreous china wash down water closet pan (Pedestal pattern) white incl \"P\" or \"S\" trap and making good the disturbed surface to match with the existing complete all as specified and as directed. |
| 101 | S&F Magic eye piece to door shutter complete all as specified & directed. |
| 102 | S&F in repair stainless steel peg set of six of size 450x35x2 mm complete all as specified and directed. |
| 103 | S&F in repair 15 mm dia stop cock/angle cockcast copper alloy chromium plated screwed downhigh pressure with crutch or butterfly handle, flenchscrewed both ends for iron or for union.fixed in repair (Make: Cera new cat no F2002201, Jaquar cat no CON-CHR-053 KN, Pearl cat no ARI-004). |
| 104 | S&F in repair bib taps brass cromium plated 15 mm bore size screwed down screwedfor iron pipe or for brass ferrule (make: Cera cat no F1015151, Jaquar cat no continental CON-CHR-047 KN, Pearl cat no ARI-003 ) |
| 105 | S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed. |
| 106 | S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed. |
| 107 | M&L for cutting hole of 230x230x230mm in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mm x6mm, 1m long each incl running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of primer over exposed steel surfaces for cooler stand, complete all as specified and directed |
| 108 | S&F 25mm stainless steel curtain rod with fancy type braket and end caps complete all as specified and directed. |
| 109 | S&F for 25mm thick Flush shutters, solid core construction,with partical board core and plywood face panels, commercial type on both sides complete all as specified & directed. |
| 110 | S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised with width of flap 40mm complete all as specified & directed. |
| 111 | S&F for Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, 100mm complete all as specified & directed. |
| 112 | M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas, wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existingfinihes with andinclmaterialand labore in CM 1:4 mixed with WPC/PCC 1:3:6 type B0/Bk work in CM 1:4 as required at site complete all as specified & directed. |
| 113 | Supply and fixing PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed |
| 114 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in soft loose soil complete all as specified & directed. |
| 115 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft and loose soil complete all as specified & directed. |
| 116 | M & L Hard core of broken bricks, broken to gauge n exc 63 mm complete all as specified & directed. |
| 117 | Supply and laying sand (25 mm thickness ) for cushioning to interlocking paver block complete all as specified and directed. |
| 118 | M&L for 60 mm thick Machine pressed vibrator type precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed. |
| 119 | M&L Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed. |
| 120 | S&F Roof trusses (framed), trussed, purlins, rafter, columncrane gantires, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel hollow M.S. Tube or flat sections) including distance pieces, cleats gusset plateetc. (Fe-410W(GdeE-250) quality B) complete all as specified & directed. |
| 121 | S & F for PVC (SWR) couplers of dia 75 mm complete all as specified & directed. |
| 122 | S & F Health Faucet 8 mm dia 1.2 mtr long flexible tube & wall hook complete all as specified and directed (Model : ALD-573, Make : Jaguar OR MARC, JOHNSON). |
| 123 | Dismantling of floor of WC and bath not exc 500mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat@ 1.50 Kg/Sqm glass fiber reinforcement and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MC Bauchemie India Pvt Ltd.(d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified.(e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall.(f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(g) The area of Each WC portion is n.exc 2.00Sqm each.(h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account. Note : The work will be executed by authorised manufacturers/ applicator. |
| 124 | M&L for Cement concrete (1:2:4) ty B1 using 40mm graded stone aggregate as in foundation,filling and mass concrete complete all as specified & directed.. |
| 125 | S&F in repairs, plastic water closet (EWC) seat cover white closed pattern with flat bottom and cover icluding mild steel chromium plated hinging device complete all as specified and directed |
| 126 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified & directed. |
| 127 | S&F 5.50 mm thick plain sheet glass selected quality, cut to size fixed in aluminium windows by using rubber gasket and aluminium snap beads, complete all as specified & directed |
| 128 | Dismantling structural steel work including doors, gates, railings etc, but excluding framed truss etc complete all as specified & directed. |
| 129 | S&F steel railing, frames, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles complete all as specified and directed |
| 130 | M&L preparation of new plastered surface of wall and applying 2mm thick wall care putty and making the surface smooth and applying and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on wall surfaces complete all as specified and directed. |
| 131 | Demolition and breaking up drain pipes 150mm Dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified & directed. |
| 132 | M&L for concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete (1:3:6) Ty C2 using 40mm graded stone aggregate for 150mm pipe complete all as specified & directed. |
| 133 | M&L for plain cement concrete (1:3:6) ty C-2 using 40mm graded stone aggregate as in foundation in foundations, filling and mass concrete complete all as specified & directed. |
| 134 | M&L for 150mm dia Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified & directed. |
| 135 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete all as specified & directed. |
| 136 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces on wall using water proofing compound. (WPC will be measured and paid saparatly) complete all as specified & directed. |
| 137 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified & directed. |
| 138 | Add or deduct for each 25 mm girth or part there of over or under 30cm ditto |
| 139 | Providing precast cement concrete (1:2:4) Ty B-I using 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified & directed. |
| 140 | S&F for TMT steel bars 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed. |
| 141 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete incl fixtures and fittings suze as swithes, ceiling rose, pendant, regulator, ssockets, light fittingetc. removing materials to store for keeping in safe custody or for taking credit (Credit for above items should be as per conditions separately) and making good disturbed surfaces of walls, floors etc, complete all specified and directed. |
| 142 | Material and labour for point wiring with 1.5 sq mm PVC insulated, unsheathed, stranded copper conductor (FRLS-H) cable single core 1100 Volt grade in and including rigid PVC conduit medium grade 20mm dia or more ISI Marked concealed conduit/ casing caping and conduit accessories and cutting chases of suitable girth where required on brick/concrete surface & making good disturbed surface, provision of GI/Pressed steel terminal switch box with plastic laminated sheet 3 mm thick fixed with brass screw and washers along with 1.5 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLS-H ) as earth wire connected with main common earth dolly complete all as specified and directed for the following :- |
| 143 | One light/fan/bell/exhaust fan point controlled by one, one-way Piano type switch 5/6 Amp complete all specified and directed. |
| 144 | One 3pin/5pin 5/6 Amps socket outlet on same board controlled by one, one-way Piano type switch complete all specified and directed. |
| 145 | One 3pin/5pin 5/6 Amps socket outlet on independent board controlled by one, one-way Piano type switch complete all specified and directed. |
| 146 | S&F switch piano flush type whitefinish 5/6Amps, single pole one way , 230 volts, 50 hz complete all as specified & directed. |
| 147 | S &F socket out let2 pin 5/6 Amps & 3 pin 5/6 Amps flush type, 230 volts, 50 hz all as specified and directed. |
| 148 | M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body all as speccified and directed . |
| 149 | Allas per item No 141 above but with 2.5 Sqmm (nominal area) FRLS-H cable PVC for the 15 Amp 3/5 pinsocket power point including 2.5 Sqmm copper conductor green colour for earth continuity conductor complete all as specified & directed. |
| 150 | S&F socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type, complete all as specified & directed. |
| 151 | S&F switch piano flush type polycarbonate single pole one way 15 Amps complete all as specified & directed. |
| 152 | S&F electronicfan regulator 230 volts , step type (5 step) socket type ,hum free 100/300 watt complete all as specified and directed. |
| 153 | Supply & Fixinglamp holders (metal ring) PVC / polycarbonate type with back plate, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm diacomplete all as specified and directed. |
| 154 | S&F LED bulb 12 watt, 2700 K, 1080 lumen, ISI marked, with B-22 base cap, as per standard specifications, complete all as specified and directed. |
| 155 | S & F Bell electric AC 230 Volts single pole ding dong type, complete all as specified & directed |
| 156 | M&L bell push AC, SP 240 volts flush type 5/6 Amps, 230 volts, 50 hz complete all as specified and directed. |
| 157 | Taking down sub main wiring and S & F Sub main wiring with two runs of single core FRLS-H PVC insulated and unsheathed multistranded, copper conductor cable of size 6.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20mm/approprite dia with accessories and fittings and one run of 2.5 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm/approprite dia shall be measured as one run length, Cable required for connection to DBs shall deemed to be incl and shall not be measured separately. Earth wire shall run inside the conduit pipe(Note :- Extra length of cable required for connection to MCBs shall deemed to be included in unit rate.) |
| 158 | S & F Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar, earth bar, single pole and neutral 250 volts, flush to wall complete all as specified and directed. |
| 159 | Supply & fixing MCB, SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified and directed. |
| 160 | Supply & fixing MCB, SP, AC, 240 volts of 40 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified and directed. |
| 161 | Supply & fixing MCB, SPN, AC, 240 volts of 40 Amps capacity 10KA, \"B\" series and making connections with suitable size of copper lugs complete all as specified and directed. |
| 162 | S&F LED tube light batten 20 watts 4 fts extruded polycarbonate housing, translucent diffuser with LED light source, 2000 lumen, natural white, surge protection range- 2KV, voltage protection range 120-280 VAC with intergrated driver and surge protection complete all as specified and directed. |
| 163 | Supply and fix LED 25 watt Building security light fitting with IP 66 protection mounting type made out of one piece in pressure die-cast aluminium housing with high efficient LED as lighting source and PC Cover separate compartment for driver, including bracket clamp and fixing accessories complete with electronic driver and all accessories, duly prewired complete all as specified and directed. |
| 164 | Supply and fix ventilating / PVC exhaust fans fancy square type 250 mm sweep with plastic fiber body heavy duty 230 Volt AC, single phase complete with plastic louvers and including making suitable size of holes in wall for fixing the fan & making good including making electrical connection with ceiling rose complete all as specified and directed. |
| 165 | Supply and fix steel body exhaust fans 300 mm sweep heavy duty 230 Volt AC, single phase complete with plastic louvers and including making suitable size of holes in wall for fixing the fan & making good including making electrical connection with ceiling rose complete all as specified and directed. |
| 166 | S & F in replacement of old unserviceable distribution board (DB) VTPN 4 way made out of sheet metal enclosure (CRCA sheet) dust and vermin proof IP 43 (double door) with 250 Amps rated copper bus bar neutral bar, earth bar, triple pole and neutral, with provision for 160A MCCB as incomer and MCBs TP/DP/SP as outgoing, flush to wall complete all as specified and directed. |
| 167 | S & F in replacement of unserviceable MCCB 100 Amp four pole, 415 volt, 25kA adjustable thermal and manetic setting including necessary connection complete all as specified and directed. |
| 168 | M&L for maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed,CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 50kg/pit(resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7.The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270 x 240 x 200mm) andFRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including medium grade rigid PVC conduit upto 10 mtr incl cutting and chases on wall / floor and making good using PCC work, including transport, labour etc, complete all as specified and directed. |
| 169 | Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories (without remote), 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00, BEE Five star rated with brushless direct current motor (BLDC), complete all as specified and directed. |
| 170 | Supply and fix electric water heater storage type, capacity 25 litres, BEE 5 star rated, ISI marked, and all connected accessories complete all as specified and directed. |
| 171 | S&F PVC Stainless Steel Connection Pipe, of length 18 Inch, suitable for geyser connection, as per standard specifications, complete all as specified and directed. |
| 172 | S & F Single pole and Neutral enclosure with a two pin and earth plug and socket complete with single pole MCB 20 amp complete all as specified and directed. |
| 173 | S & F angle stop valve of size 15 mm dia, CP Brass Angle valve screwed for iron pipe and fixed complete all as specified and directed. |
| 174 | Supply and fix GI tubing medium grade ISI marked of 15 mm bore dia with all fittings to wall, floor etc complete all as specified and directed. |
| 175 | M & L for Circuit/submain wiring withsingle core FRLS-H PVC insulated copper stranded conductor cable drawing into existing PVC rigid conduitsurface /concealed/ casing caping as required of 1.5 Sqmm for Inverter wiring complete all as specified and directed. |
| 176 | Dismantling & taking out old unserviceable LT UG cable & Supplying, laying, jointing and testing LT underground cableof size 25 Sqmm 4 core, heavy duty, 1100 Volts, PVC insulated and sheathed, armoured with multi-stranded aluminium conductor cable conforming to latest IS, laid in trenches/ducts or fixed to poles/walls or laid under roads /paths /drains / culverts. |
| 177 | Excavation in trenches in soft/disintegrated soil not exc 1.5 m wide and not exceeding1.5m in depth forlaying UG cable/foundation etc complete all as specified and directed. |
| 178 | Returning filling in soft/disintegrated soil including spreading levelling watering and well ramming in layers n.exc 25cm each layer complete all as specified and directed. |
| 179 | Removal of excavated surplus soft/disintegrated soil to a distance not exc 50 mtrand depositing where directedat a level not exc 1.5 mtr above the starting point complete all as specified and directed. |
| 180 | Material and labour for double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etcfor protection of LT cable XLPE grade 1100 volts complete all as specified and directed. |
| 181 | Labour and T&P for horizontal boring of hole passing through pavement/ road/ hardstanding by manual or mechanical means suitable for 50mm bore complete all as specified and directed |
| 182 | Supply and laid GI medium grade pipe for cable protection of size 40 mm dia complete all as specified and directed |
| 183 | Taking up or down galvanised steel tubing of size 20mm bore and connections complete all as directed. |
| 184 | Supply and fix 20mm bore galvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in floor fixed on wall or ceiling complete all as specified and drected. |
| 185 | Supply and fix or lay in trenchesgalvanised steel water tubing medium grade including all fittings such as bends, elbows, tees, reducers, sockets, union etc and laid in trench complete all as specified and drected of size 20 mm bore complete all as specified and directed. |
| 186 | Drilling and tapping GI water mains 50mm bore (in position) for branch connections of the internal dia 20mm, complete all as specified and directed. |
| 187 | S&F straight plain brass ferrules (or connecting screws) screwed both ends and fixed to water mains for tapping branch connection of 20 mm bore pipe, complete all as specified and directed. |
| 188 | S&F gun metal globe or gate valves for 20mm nominal bore (Class-1) with iron wheel head, srewed both ends for iron pipe ISI marked, complete all as specified and directed. |
| 189 | Oxygen Base Unit (CE Marked): Supply, installing, testing and commissioning of Oxygen Base Unit comprising of following works :-(A)OxygenManifold 4+4 cylinders configration : - The oxygen manifold would be of above size of bulk oxygen cylinders. It is suitable to with-stand a pressure of 2400 psi. The main frame made out of 50 X 50 X 6 mm angle iron and bottom frame of 20 X 20 mm MS hollow square section, installed in such a way that the cylinders must be stayed for use in upright position and are not fell down under any circumstances.The gases passed through inter-connecting tail pipes duly fitted with suitable bull nose and nut adopter for cylinder valve and tube size is 10 mm OD Copper tube duly annealed having wall thickness 1.5 mm in spiral shape and the other end of the tail pipe are fixed with non-return valve. The non return valves are fixed in brass block of size 25 mm square vertically which are fitted with high pressure copper tube of size 15mm OD having wall thickness 1.5 mm. Both the arms of manifold further fixed in automatic control panel. All the joints of copper tube, brass block and inter connecting tubes are welded with silver brazing. Pressure release safety valve also provided. The manifold is fabricated in such a way to give distribution flow of 1500 Ltrs per minute. The manifold would be degreased and purged with inert gas before commissioning. The manifold would be enamel painted as per colour code. All above work would be done strictly as per specification and entire satisfaction of Engineer in-Charge. |
| 190 | S&F Oxygen Emergency Point CE Marked with the following :-SPECIFICATION:- In case of emergency, the supply of medical oxygen is restored immediately with this system. The emergency system would be consists of 04 No. cylinders - configuration. This would be suitable to withstand a pressure of 2400 psi. This wouldbe inter connected with high pressure, high flow, double stage control regulator duly fitted with cylinder contents as well as line pressure gauges of 50mm dial size. Pressure release safety valves are also to be provided in this system, so that it would release the pressure beyond 70 PSI. The outlet point of pressure regulator would be connected with emergency point of oxygen pipe line with the help of inter-connecting adopters complete all as specified and directed. |
| 191 | S&F OXYGEN CONTROL PANEL FULLY AUTOMATIC CE Marked WITH FOLLOWING :- Fully Automatic Control Panel SPECIFICATION:The control panel would be supplied as a pre-tested and pre-sated self-contained unit. The control panel is installed in the middle of both arms of manifold and fabricated in such a way that it would withstand of working pressure 2400 psi and test pressure would be 3500 psi.It would also supply a flow of 1500 Ltrs per minute at a pressure of 4 bar (60 psi) constantly on either bank.FEATURES • Electric audio- visual indicators for each bank status.• Electrically audio-visual indicators at the time of manual changeover.• Impact and weather resistance coloured cover.• Independent gauges and indicators.• Manual change over from on line bank to reserve bank and vise versa.• In built low-pressure audio visual alarm. |
| 192 | Supply, laying, testing and commissioning of 12mm bore Copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition complete with necessary fixing and clamping arrangement to wall/ ceiling/ false ceiling all as specified and as directed. |
| 193 | Supply, laying, testing and commissioning of 15mm bore Copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition complete with necessary fixing and clamping arrangement to wall/ ceiling/ false ceiling all as specified and as directed. |
| 194 | Supply, laying, testing and commissioning of 22 mm bore Copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition complete with necessary fixing and clamping arrangement to wall/ceiling/false ceiling all as specified and as directed. |
| 195 | Supply, laying, testing and commissioning of 28mm bore Copper tube of soiled drawn seamless deoxidized, non-arsenical, half hard, tempered and degreased as per BS EN 13348:2001 duly supported with manufacturer test certificates for physical properties and chemical composition complete with necessary fixing and clamping arrangement to wall/ceiling/false ceiling all as specified and as directed. |
| 196 | Supplying, installing, testing and commissioning Oxygen Gas Terminal Units (Oxygen Gas Outlets) with adaptors/probe for oxygen, compressed air and vacuum: Matching adaptors to the gas outlet mentioned above i.e. adaptor for oxygen, air and vacuum. The terminal units would have following features :-(a)It would be front insertion type.(b)Terminal unit would have mechanism with check valve.(c)Allow single hand operation. (d)On first insertion of probe the probe shall sit in a standby position. At the stage there shall be no gas flow. (e)Only on pressing the probe second time, the gas supply would start.(f)They would close automatically when connected apparatus is removed.(g)For allowing on line maintenance the terminal unit would be equipped with a check valve for all positive pressure gases for closing gas supply whenever the outlet point is opened.(h)The outlet would be non inter-changeable for specific gas and it would accept only correct medical gas adopter/Probe.(i) It would be colour coded as per HTM 2022(j) The design of this outlet would be compatible to installed vertical on valve horizontally on ICCU panel and area servicing unit and also vertical to fit in pendants.(k)It would only supply with correct probe/ adopter. |
| 197 | Supply and fix isolation valves (CE Marked)to control the pressure as well as for maintenance quarter turn open at 90-degree ball type valves would be provided. These valves would be of nickel-plated brass body having PTFE seat and inner outer seals. These valves would have stainless steel ball of specific ID clearance so that line pressure would not drop. For installation only PTFE gaskets would be used in between nuts and valves to prevent leakage.All the nuts for fixing the ball valve would be of brass with brass nozzles for easily brazing with copper tube. All ball valve assemblies would be on approachable height for easy operation of following sizes: |
| 198 | 12 mm |
| 199 | 15 mm |
| 200 | 22 mm |
| 201 | 28 mm |
| 202 | Supply, install, testing and commissioning of Isolation Valve Assembly: CE marked, ISO 9001-2008, for Oxygen gas comprising of following:-SPECIFICATION: To control the pressure as well as for maintenance quarter turn open at 90-degree ball type valves would be provided. These valves would be of nickel-plated brass body having PTFE seat and inner outer seals. These valves would have stainless steel ball of specific ID clearance so that line pressure would not drop. For installation only PTFE gaskets would be used in between nuts and valves to prevent leakage.All the nuts for fixing the ball valve would be of brass with brass nozzles for easily brazing with copper tube. All ball valve assemblies would be on approachable height for easy operation and enclosed in powder quoted visible box.TECHNICAL SPECIFICATION1. Leakage Clause : 12. Temperature range: Ambient3. Working Pressure: 7.5 bar maximum4. Test pressure : 50 bar maximum5. Standard : As per HTM 20226. Size : 15mm to 28 mm |
| 203 | Supply, installing, testing and commissioning of Oxygen Gas Monitoring Alarm System : CE Marked (AREA-WISE/MAIN)SPECIFICATION:- A Gas failure Alarm would be provided which must be capable of monitoring all the Medical Gases. This alarm would be of ELECTOMECHANCIAL TECHNOLOGY to detect the fault, pressure sensors, which detect deviation from the normal operating limits, would be installed. Each pressure Gas would be displayed by coloured LEGEND\"S to show normal and ‘Low’ conditions. At the time of receiving the fault the normal window/indicator stop indication and other window would blink and it also gives audio alarm. The alarm panel would have a test facility to check the internal circuits, mute facility for making silent the buzzer, acknowledgement facility for receiving the fault and reset facility for resetting the alarm after rectifying the fault.TECHNICAL SPECIFICATIONS1. NO/NC type Selectable : DIP switches/ sensor.2. Contacts : Volt free3. Input voltage : 240 volt AC4. Input circuit : Optocouped by using isolating Device5. Output Circuit: 12 volt DC.6. Contact rating : 1 Amp/240 volt AC.7. Window size: 26 mm/ indication lamps. 8. Colour : Bright Red/ Yellow/ Green.9.Lead Life : More than 800 hrs.10.Flash rate : 50 / Min.11. Power consumption: 1.5 Wt. Maximum12. Mounting: wall mounted 13. Temperature limit: 60 oC14. Humidity Limit : 95 % RH15. Power supply : AC/240 Volt+ 10% |
| 204 | Supply, installing, testing and commissioning of Bed Head Panel CE MARKED AS PER HTM 2002 : The modular medical bed head panel1200 mm long:would be fabricated of aluminous die pressed 1.6 mm thick imported laminated sheet in such a way to provide 100% safe and efficient means to deliver all the gases as well as electrical to the patient/staff in intensive care conditions. To enclosed all piping, electrical wires, monitor wire etc would be fitted continuously running on wall. The design of modular BHU would consist of aluminum section to meet the requirement of HTM 2002, NFPA and other international standard. It would have separate duct for medical gases as well as electrical. There would be no sharp edges having smooth finish and without any visible screwetc. It would be having ability to fix medical gas outlets, electrical sockets, It would also have colour code around the specific gas outlet and a slide rail for focus lamp. It would be polyester powder coating finish on all external surfaces and would be fitted to wall with the help of 8mm fasters at specific height. It would be fixed in such a manner that it could be removed easily for servicing and repair. It would be long and continuous to fix for any distance. Following accessories to be fixed on Pendant:1. 02 Nos5 Amps Sockets along with switch ,2. 02 Nos5/15 Amps Sockets along with switch;2. 01 NoI.V Hook. |
| 205 | Supply, installing, testing and commissioning of BPC (Back Pressure Compensated) Flow meter with humidifier bottle CE MARKED- would be BPC single type Pipeline Flow Meter unit duly fitted with the fine adjustment valve. It would be back pressure compensated to bear and control the Oxygen Pressure approx 60 psi. Flow meter unit would be consisting of double wall rotta-meter has range of flow 0 to 13 ltrs. per minute with fine adjustment valve. The rotta meter and humidifier bottle would be made of clear, impact resistance polycarbonate (duly graduated). This unit would be having attachment to fit humidifier bottle of capacity 100 Ml. consist of clear, impact resistance polycarbonate jar. This would also have Reciprocating on top for flow meter/plastic cap having nozzles for outlet tubes and the inlet tube end would be multi function combination bubblier/ nebulizer to add the humidity and create an aerosol in Medical Gas min marks would be on jar. This unit would be supplied with PVC Clear green tube of 1.5mtr long duly fitted with disposable Oxygen mask. |
| 206 | Material and labour for submain wiring with two runs of single core FRLS-H PVC insulated and unsheathed multistranded copper conductor cable of size 2.5 Sqmm LT, 1100 V grade drawn through and including adequate size PVC non metallic conduit 20mm or more of appropriate dia with accessories and fittings and one run of 2.5 Sqmm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and as directed.Note:Two runs of cable one run of earth wire and one run of non metallic PVC conduit of approproae dia shalol be measured as one run length of sub main wiring. |
| 207 | Material and labour for submain wiring with two runs of single core FRLS-H PVC insulated and unsheathed multistranded copper conductor cable of size 4.0 Sqmm LT, 1100 V grade drawn through and including adequate size PVC non metallic conduit 20mm or more of appropriate dia with accessories and fittings and one run of 4.0 Sqmm single core multi stranded copper conductor cable as earth continuity conductor complete all as specified and as directed.Note:Two runs of cable one run of earth wire and one run of non metallic PVC conduit of approproae dia shall be measured as one run length of sub main wiring. |
| 208 | Supply and fixing sheet metal enclosure double door type for MCBs DB SPN (Single pole and neutral) 240V AC 4 way with 200 Amps rated busbar all as specified and directed. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
