Tender For Invitation Of Quotation For Supply Of Cat B Stores-Multi State

Tender For Invitation Of Quotation For Supply Of Cat B Stores; Auto Electric Test Bench Instrumentation: 3 independent ammeters-0-200 amps DC. (For Alternator, Starter and Battery) 1 common voltmeter-0-100 V DC Drive: 5Hp. 1440 RPM 3Phase foot-mounted induction mator Protected with Circuit Motors Protection Main MCB Complete Test Bench protection Built-in overload relay motor protection Electronic Cutt-off Starter short circuit protection MCBS-Starter AC circuit protection Power Requirement: 3ph -5 wire system with 415V/50Hz, 15 Amps capacity-R/Y/B/N with grounded Rugged mounting suitable for all alternators Joke: Dimensions 900 x850 650mm (LBH) Radial Drill Machine Drilling Capacity: 20mm Motor: 1 HP, 3-Phase Spindle Speed: 96-2600 RPM Spindle Travel: 150mm Table Size: 400x300mm Drill Chuck: 13mm Arbor Forward/Reverse Switch V-Bell Drive Alternator/Regulator Tester (Digital 24V) Automatic testing of 12v and 24v regulators for pass or fail results Accurately display the regulating voltage Dynamic mode operation with regulators constantly switching on and off when under test. Ability to test regulators ranging from 6v to 32v Capability to test various types of regulators including A crouit/B circuit, and DP type regulators. Not applicable for mechanical regulators Active Lamp Function under fault conditions such as loss of stator/phase or battery sense lead or overvoltage, triggering a warning lamp and a relay to shed certain loads under demanding conditions In-built DFM (Digital Field Monitor) for replicating the field signal and informing the ECU of Alternator Loading Portable Flood Light with Stand Portability. The light tower should be highly portable with a maximum weight of 55 KG Dimmer Function: Should include a dimmer function allowing for adjustable brightness between 10% and 100% Light Output: Must have output of a minimum of 20000 lumens Height: The height of the light tower should extend to a minimum of 3 meters. Tower Material: The tower should be constructed of durable aluminium Battery Type & Charger The light tower should be powered by a lithium- lon battery and come with a compatible 24V 20 AMP charger, Wind Support: The product should include a wind support mechanism for use in windy conditions. Charging Time: Full charging time should not exceed 12 hours Wheel Size. The product should include at least 8 wheels for mobility. Mast Mechanism: Should incorporate a hand or foot pump mechanism for raising and lowering the mast. Battery Backup: Battery backup for a minimum of 7 hours. The product should come with a rain cover for the light Pneumatic Tool Installation (with Tool, Air Compressor & Pipe 50 Mir) Compressor Technology: Reciprocating Compressor Model Name/Number SCPH-100P Discharge Pressure: 12 bar Air Tank Capacity: 500 Litre Power Source: AC Three Phase Air Quality Standard: Classi Cooling Method: Air Cooled Warranty: 1 year Motor Speed: 720 RPM Frequency 50 Hz Voltage: 380 V Maternal: Mild Steel Free Air Delivery: 31 CFM Piston Displacement: 36.2 CFM Pneumatic connection fitting for 50 meters with four takeoff points with Brass valve MS pipe Rubberised pipe T-joint -Hexagonal nipple Pipe clamps Crimping Machine Hose 1.D. Range: 12 mm to 80 mm Hose OD Range: 12 mm to 102 mm Opening Dia (without Dies): 120 mm Accuracy: 0.01 mm Hydraulic Oil Encio 68 Power: 5 HP, 3 PH, 1440 RPM Standard Voltage: 375-420 V Frequency: 50 Hz Phases: 3 Number of Die Sets 12 nos Hydraulic Tank Capacity: 75 Lirs Crimping Force: 550 Tanne Die Length: 100 mm Dimension of Machine (L x W x H): 1000 x 800 x 1550 mm Weight of Machine: 700 Kg (Approx) Control Panel: PLC Control HMI Display Panel (Digitally Controlled Stroke for Pre- setting of Crimped Dia.) Fully Automatic MPFI injector Tester with Electrical Part Testing Machine Type: The injector tester should be automatic minimizing the need for manual operation Pulse. The tester should have a pulse range from 0 to 20.0 ms, with a step increment of 0.1 ms, allowing for precise control suring injector testing Material. The tester should be constructed from high-quality durable metal suitable for industrial use Length of Cable. The tester should have a cable length of approximately 7.2 meters allowing for flexible use within a spacious area Cooling Mode: The tester should feature a recycle cosing mode for efficient temperature managemant during prolonged use Airflow. The tester should have an airflow sapacity of 48 Lis providing effective ventilation during operation. Function: The tester should have a wet-dry function, providing versatility during different testing scenarios

Refer document

INR 50.19 Lakhs /-