|
| 1 | Dismantling plain corrugated CGI/PGI sheet in roof covering including redges completeall as specified and directed by Engineer-in-charge. |
| 2 | Supply and fixing 0.63mm thick galvanised, corrugated mild steel sheeting with two corrrugations side lap, fixed with coach screws and washers, in roofs, wall etc. with grade of zinc coating 275 completeall as specified and directed by Engineer-in-charge. |
| 3 | Supply and fixing 0.63mm thick galvanised, plain mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specifiedand directed by Engineer-in-Charge. |
| 4 | Excavation in post holes not exceeding 0.5 cum each getting out , returning filling in and ramming earth around in layers not exceeding 25 cm each all as specified in hard/dense soil including removal of surplus soil upto 50 mtrs distance complete all as specifiedand directed by Engineer-in-Charge. |
| 5 | Material and labour for cement concrete 1:3:6 Type C-2 (using 20mm greded crushed stone aggregate)as in foundations filling and mass concrete complete all as specifiedand directed by Engineer-in-Charge. |
| 6 | Supply and fixing Fe 410-W(Gde E 250)quality B rolled mild steel in roof trusses (framed) trussed, purlins, crane gantries, rails and framing (beam, tee, angle, channel or flat sections) including distance pieaces cleats etc complete all as specifiedand directed by Engineer-in-Charge. |
| 7 | Supply and fixing MS plates Fe 410-W(Gde E 250) quality Aplain or chequered square cut or notched forming holes drilled or welded any thicknesscomplete all as specifiedand directed by Engineer-in-Charge. |
| 8 | Material and labour for framed work such as steel doors, gates or other section or angle, Fe-410-W Gde E-250 of quality \"A\" complete all as specifiedand directed by Engineer-in-Charge. |
| 9 | Material and labour for preparation of new steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer over a coat of moderant solution to remove zinc coating complete all as specified and directed by Engineer-in-Charge |
| 10 | Material and labour for preparation of new steel and iron surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint (camouflaged pattern) over a coat of red oxide primer over a coat of moderant solution to remove zinc coating complete all as specified and directed by Engineer-in-Charge |
| 11 | Taking down chowkats or frames including shutter exc 1.50Sqm but n. exc 4.00Sqm complete all as specifiedand directed by Engineer-in-Charge. |
| 12 | Supply and fixing 35 mm thick plain framed panelled shutters (two planel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of the rail and stile as per IS:1003(Part I), kiln sseasoned and chemically pressure treated, complete all as specifiedand directed by Engineer-in-Charge. |
| 13 | Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cutand fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. and of approved quality with 6 mm thick figured glass and SS wire mesh of 0.36 mm nominal dia and average width of aperture 1.40 mm, complete all as specified and directed by Engineer-in-Charge.Note:- The rate shall also include making all damages/plasteringrepair, leveling and making good in plumb all the cills and jambs of opening before fixing windows and , shall deemed to have been included in the quoted rate and no extra shall be admitted at a laterdate in this respect ,complete all as specifiedand directed by Engineer-in-Charge. |
| 14 | M&L for 5.5 mm thick plain glass fixing and glazing with aluminium beading and rubber gasket including haking out old broken glassin aluminium door and window frame complete all as specified and directed |
| 15 | S&F in repair galvanised mild steel wire cloth nominal dia of wire 0.56mm and average width of aperture 1.00mm in wooden/steel frame complete all as specified and directed |
| 16 | Providing and fixing factory made uPVC white colour casement (Openable) Door made with 3D hinges made of (Big series) frame size 60x58 and sash(67mm x 110mm) and and both having wall thickness of 2.3 +- 0.2mm and single glazing bead of appropriatea dimsion (area updoor up to 2.00 sqm mtr comprising of uPVC mutlichambred frame , sash andmulion (whereever required) . Extruded profiles duly reinforced with 1.6+- 0.2mm thick glavangaded mild steel section made from roll forming process of required lenght (shape and size according to uPVC profile), uPVC extruded glazing bits of the appropriate dimension ,EPDM gasket , zinc alloy ( white powder coated 3D hinges and one handle of each side of pannels alongwith zink plated mild steel multi point blocking having transmission gear , cylinder with keeps and one side key8mm x 100mm long GIfasteners for fixing frame to finished wall and stainless steel screwsetc profile of frame & sash shall bealso fusion welded including drilling of holes for fixing hardwere and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required sizeand of spproved quality complete all as specified and directed by Engineer - in - charge (Glass shall be paid separately) Note: For uPVC frame ,sash and mullion extruted profiles minus 5% tolerance in dimension i.e in depth & width of profile shall be accpatble . Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made,complete all as specifiedand directed by Engineer-in-Charge. |
| 17 | Supply and fixing 20mm thick uPVC panels for fixing to uPVC door framecomplete all as specified and directed by Engineer - in - charge. |
| 18 | Supply and fixing 100 mm butt hinges, heavy weight, cold rolled mild steel and fixed complete all as specified by Engr-in-charge. |
| 19 | Supply and fixing 150 mm size aluminium handles, cast type,anodised complete all as specified by Engr-in-charge. |
| 20 | Supply and fixing 150 mm aluminium anodised barrel tower bolts extruded section fixed complete all as specified by Engr-in-charge. |
| 21 | S&F in repair 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specifiedand directed by Engineer-in-Charge. |
| 22 | Material and labour for brick work with sub class \"B\" bricks in cement motor 1:6, straight or curved on plan exc 6 mtr nean radius, using old size bricks. complete all as specifiedand directed by Engineer-in-Charge. |
| 23 | Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement motor 1:4 finished even and smooth without using extra cement complete all as specifiedand directed by Engineer-in-Charge. |
| 24 | Material and labour for 15mm thick rendering in cement mortar 1:6 on fair faces of brick work surace rendering is to be even and smooth with out using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material and labour for preparation of new plastered surfaces and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/lit and UV resistance as perIS 15489:2004, Alkali and funggal resistance , dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/10 sqm over and including priming coat of exterior primer applieed @0.90litre/10sqm over new surfaces complete all as specifiedand directed by Engineer-in-Charge. |
| 26 | Material and labour for Preparation new surfaces of walls and applying two coats of oilemulsion distemper over a coat of 3 mm thick wall putty complete all as specifiedand directed by Engineer-in-Charge. |
| 27 | Demolition of cement Concrete(unreinforced)in ground floors and pavings not exc 15 cm thickness (below or above ground level) or as in sunken complete all as specifiedand directed by Engineer-in-Charge. |
| 28 | Material and labour for glass dividing strips, 3mm thick(38mm width of strip) complete all as specifiedand directed by Engineer-in-Charge. |
| 29 | Material and labour for 40mm thick PCC(1:2:4) type B-1 using 20mm graded crushed stone aggregate) as in floors complete all as specifiedand directed by Engineer-in-Charge. |
| 30 | Material and labour for 100 mm thick Cement concrete type C-1,1:3:6 (20mm using graded crushed stone aggregate) as in sub base finished even and rough, complete all as specifiedand directed by Engineer-in-Charge. |
| 31 | Supply and fixing vitrified ceramic tiles light shade, 10 mm thick (square/rectangular) polished, area of each tiles notexc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cementto match including 15 mm thick screed bed in cement motor 1:4 complete all as specifiedand directed by Engineer-in-Charge. |
| 32 | Dismantling floor hearth wall tiling (but not backing) removing servicable tiles to store rubbish off the premisses complete all as specifiedand directed |
| 33 | Material and labour for 15mm thick screed bed or bedding layer of cement mortar 1:4 to laying floor finish complete all as specifiedand directed by Engineer-in-Charge. |
| 34 | Material and labour forchequered cement concrete tiles 20cmx20cmx25mm thick, set jointed and pointed in neat cement slurry in floors, with grey cement and pigment complete all as specified and as directed by the Engineer-in-Charge |
| 35 | Material and labour for PCC 1:2:4 Type B1 using 20 mm graded crushed stone aggregate as in wall or retaining wall, any thickness, size or shape including pilasters buttresses columns, pillars boundary pillars andposts (including caps and bases) complete all as specifiedand directed by Engineer-in-Charge. |
| 36 | Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc, verical or to batter, work in rough finished flat surfaces of concrete ccomplete all as specifiedand directed by Engineer-in-Charge. |
| 37 | Supply and fixingPVC (SWR) pipes single socketed, in any length of 110mm bore with rubber ring joints, laid in wall & trenches , complete all as specifiedand directed by Engineer-in-Charge. |
| 38 | Material and labour for broken stone or boulders hand packing ( n exc 63mm thickness), at back of walls over arches etc and raising (or lowering) to the required level complete all as specifiedand directed by Engineer-in-Charge. |
| 39 | Demolition ofBrickwork or Stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed by the Engineer-in-Charge. |
| 40 | Taking down old unserviceable/deteriorated batten/PVC conduit point wiring from existing place i.e.light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets, ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Peris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash complete all as specified and as directed by the Engineer-in-Charge. |
| 41 | Taking down main switch/DB/ change over/AC box of any capacity including fixing accessories of single/three phase complete all as specified and as directed by the Engineer-in-Charge. |
| 42 | Taking down old/unserviceable aluminium/coppersubmain wiring off sizes complete all as specified and as directed by the Engineer-in-Charge. |
| 43 | Material and labour for flameproof concealed point wiring on wall and surface wiring on ceiling / roof with necessary fixing arrangements with stranded PVC-FRLS insulated and unsheathed copper stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including 16 gauge stove enameled ERW rigid steel conduit (metallic) not less than 25 mm dia with all MS conduit accessories/ fittings such as, bends, tee, elbow excludingjunction boxes etc including PVC-FRLS insulated and unsheathed copper stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for one light, fan point controlled by one switch. Note : Junction boxes shall be measured separately |
| 44 | All as per item No 43.00here-in-before but for power point wiring with 2.5 SqmmPVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead. complete all as specified and as directed by the Engineer-in-Charge. |
| 45 | Supply and fixing in 16 Amp flame proof weather proof switch Socket and plug combined in LM 6 cable termination box, 250 V, 2P+earth complete all as specified and as directed by the Engineer-in-Charge. |
| 46 | Supply and fixingflame proof weather proof threaded type 3way/4way junction box 100mm dia in LM 6 aluminium alloywith all accessories complete all as specified and as directed by the Engineer-in-Charge. |
| 47 | Supply and fixingflame proof weather proof metallic hose conduit 3/4 \" dia300 mm longcomplete all as specified and as directed by the Engineer-in-Charge. |
| 48 | Supply and fixing flameproof double compression brass cable gland 3/4\" dia complete with nipples complete all as specified and as directed by the Engineer-in-Charge. |
| 49 | Supply and fixing Flame proof weather proof switch with cable termination in LM 6 cable termination box aluminium alloy housing 16 Amp, single pole 250 volts all as specified and as directed by the Engineer-in-Charge. |
| 50 | Supply and fixing Flame proof, Weatherproof LED light fitting, 1x36 wattIP-65 made of aluminium alloy LM 6 with electronic ballast, bipin holders, connector block etc complete with all accessories prewired and including connecting up with twin core twisted flexiblecopper conductor cable with suitable sizecomplete all as specified and as directed by the Engineer-in-Charge. |
| 51 | Supply & fixing energy efficientFlame proof, Weatherproofheavy duty high speed exhaust fan 380 mm(15\") sweep,matel body rust proof inbuilt safety grill, single phase 230 volts 50 Hz AC,totally enclosed heavy duty motor with die cast rotor mounted on two ball bearings complete with louvers & shutters,including making circular holes suitable for fixing of 380mm sweep exhaust fans by cutting the wall of any thickness/ required circumstances for exhaust of air and including grouting of rag/anchor bolts and nuts complete including finishing of disturbed surfaces by using cement mortar 1:3 complete and connecting electrically using 3 core 0.75 sq mm PVC insulated flexible copper conductor cable over all sheathed complete all as specified and as directed by the Engineer-in-Charge. |
| 52 | Supply and fixing in Flame proof weather proof distribution board 8 way with cable termination in LM 6 cable termination box aluminium alloy housing250 volts, complete all as specified and as directed by the Engineer-in-Charge. |
| 53 | Material and labour for Flameproof Sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 4 sqmm drawn in and including 16 gauge stove enameled ERW rigid steel conduit (metallic) not less than 25 mm dia with all MS conduit accessories/ fittings such as, bends, tee, elbow excludingjunction boxes etc including PVC-FRLS insulated and unsheathed copper stranded conductor of size 4 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for one light, fan point controlled by one switch. Note : Junction boxes shall be measured separately |
| 54 | Supply and fixing Flame proof weather proof LED light fixture of 45 watt LED, 240 Volts new generation energy saving and environmental friendly long life made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having TOP opening seperate driver compartment with IP66 protection and impact resistance of IK07, includingbracket made out of GI pipe of suitable dia medium grade, suitable length as per site requirement bent to shape with welded MS flat 25 x 6 mm for mounting of fitting with FIclamps, nuts, bolts complete all as specified and directed by the Engr-in-charge. |
| 55 | Supply and fixingFlameproof , Weatherproof Sheet metal enclosure TPNMCCB DB 4 Way, 415 Vwith bus bar double door type as per latestIEC standards suitable for flush mounting complete with 200 Amp internal copper bus bar and wiring up to terminals for cable management for DB\"s with and including MCCB4P 63 Amps (as incomer) and MCB SP 6 to 32 Amps -12 Nos (as outgoing) to be used, fixed properly in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as specified and as directed by the Engineer-in-Charge. |
| 56 | Supply and fixingvoltage surge protector in sheet steel enclosure complete, 230/240 volts AC, 1.5 KV protection level type II with remote signalling and indicator completedouble pole (SP+N)with rupturing cacpacity 40 KA including making connection and providing thimbles for out going cables. complete all as specified and as directed by the Engineer-in-Charge. |
| 57 | Supply and fixingvoltage surge protector in sheet steel enclosure complete, 230/240 volts AC, 1.5 KV protection level type II with remote signalling and indicator complete four pole (TP+N)with rupturing cacpacity 40 KA including making connection and providing thimbles for out going cables complete all as specified and as directed by the Engineer-in-Charge. |
| 58 | M&L for Earthing complete with copperearth plate electrode 300x300x3.15 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level) withtop edge of earth plate not less than 1.5 Mtr below normal ground level connected to copper strip 20X3 mm as earth lead by means of bolts, nuts washers and check nutsof steel/GI duly protected with 40 mm bore light grade pipe upto main board , 20mm bore watering pipe light gradewith CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoaldust and common salt after mixing with BFC (Back Fill Compound) inadeqate quantity as recommended by the manufacturer oras diirectred by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel withwire mesh complete and all as specified and as directed by Engr-in-charge. |
| 59 | Supply and fixing copper strip 20x3mm complete with saddles/ insulators made out of PVC or fibre and fixing screws for roof conductor/down conductor including welding or brazing for joints all as required at site or asdirected by Engr-In-Charge. |
| 60 | Material and labourfor air termination single pointed copper rod 12mm dia and 300mm long complete all as specified and as directed by the Engineer-in-Charge. |
| 61 | Material and labourfor test point terminal block made of gun metal or phosphorus bronze of size 75X75X6mm drilled and screwed including 03 Nos 8mm dia 25mm long hexagonal head screw complete all as specified and directed by Engr-in-charge. |
| 62 | Supply and fixing GI tubing light grade25mm dia, cut to size and bent to shape all as required at site including fixing arrangement with necessary clamps of required size at site and providing appropriate size of insulators to pipe from foundation of air termination rod completeall as specified and directed by Engineer-in-charge. |
| 63 | Supply and fixingtesting and connecting 25 Sqmm 4 Core XLPE insulated cable, screened, PVC bedded, galvanized steel strip or wire armoured heavy duty electrical cable with aluminium conductor, 1100 volts grade laid in trenches/ducts/wall or through pipe with suitable size of cable glands, crimping type cable lugs complete all as specified and directed by Engr-in-Charge. |
| 64 | All as per item Srl No 62.00 here-in-before but of size 35 sqmm 3.5 core. completeall as specified and directed by Engineer-in-charge. |
| 65 | All as per item Srl No 62.00 here-in-before but of size 95 sqmm 3.5 core. completeall as specified and directed by Engineer-in-charge. |
| 66 | Supply and fixing ON LOAD change over switch 415 Volt in sheet metal enclosures 4 pole of capacity 200 Amps, completeall as specified and directed by Engineer-in-charge. |
| 67 | Material & labour for tubing GI light grade 50mm bore laid in trenches, ducts, floor for protection of cable,fixed to wall or poles including fixing arrangement all as required and directed by Engineer-in-Charge. |
| 68 | Supply and fixing GI strip 25x4mm complete with saddles/ insulators made out of PVC or fibre and fixing screws for roof conductor/down conductor including connections all as required at site or directed by Engr-in-Charge.. |
| 69 | Material & labour for Earthing complete with galvanised steel earth plate electrode 600x600x3.15 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level ) withtop edge of earth plate not less than 1.5 Mtr below normal ground level connected to GI strip 25X4 mm as earth lead by means of bolts, nuts washers and check nutsof steel/GI duly protected with 40 mm bore light grade pipe upto main board , 20mm bore watering pipe light gradewith CI/MS funnel and wire mesh including excavation, earth work in any type of soil and removing the surplus soil to a distance not exceeding 50 Mtr, add charcoaldust and common saltin adeqate quantity as recommended by the manufacturer oras directed by the Engr-in-charge all as shown in electrical plate No. 03 of SSR part-I 2009 having pit in PCC 1:2:4 type B-1 including angle iron frame made of angle iron of size 40x40x6mm grouted in PCC pit for CI cover of required size, funnel withwire mesh complete and all as specified and as directed by Engr-in-charge. |
| 70 | Supply and fixing Fabrication, supply, installation and testing of Feeder Pillar KIOSK type floor mounted dust/vermin proof indoor type of size 1.2 x 1.5 x 0.6 mtr or as per site requirement, CPRI approved factory fabricated made out of MS sheet of thickness 3.15 mmmounted on angle iron legs made out of angle iron of size 40x40x6 mm with front & rear opening with locking arrangement, containing bus bar chamber to accommodate 3 phase & 1 neutral copper busbar of size 40x10 mm fixed on epoxy based insulators in horizontal position in upper part of panel separate chambers for incoming and outgoing cables & MCCB, MCCB connectedto busbar by copper strip of size 20x5 mm duly drilled hole for cable connection and powder coated with 7 tank process all as required at site or as directed by Engr-in-charge(including the PCC foundation of panel) complete including of following :-(a) MCCB 160 Amps 4P 25 KA (thermal, adjustable type, O/L & S/C Protection) - 01 No (I/C). (b) MCCB 125 Amps 3P 16 KA -02 Nos (O/G) (c) MCCB 63 Amps 3P 16 KA -04 Nos (O/G) (d) ON LOAD change over switch -01 Nos (O/G) (e) Digital Multi-function meter with CT\"s of required cap – 01 No. (f) LED type Indicator lamps (R, Y. B) – 01 Set. All accessories pre wired with suitable size copper conductor cable including making necessary arrangements for fixing all as required at site or directed. NOTE :1) All connections tobe done with proper size copper/ Brass Thimbels. ( 2) Control circuit wiring to be done with S/C copper wire complete all as specified and directed. (3) All incoming and outgoing MCCB to be labelled as per the feeder area with necessary name plates. complete all as specifiedand directed by Engineer-in-Charge. |
