|
| 1 | I)Repairs of 100 HP Vertical pump set |
| 2 | Bowl assembly S.S. shaft 410 |
| 3 | Bowl assembly gum metal impellers |
| 4 | Neck Ring gun metal impeller |
| 5 | Providing and fixing Bowl assembly gun metal bush |
| 6 | Bowl assembly rubber bush |
| 7 | Line shaft EN.8 |
| 8 | S.S. slues |
| 9 | Line shaft coupling |
| 10 | Gun metal spider |
| 11 | Spider rubber bush |
| 12 | Bowl assembly bolt T.V.S. |
| 13 | Casing pipe nut bolt |
| 14 | Rubber seat |
| 15 | T.T. plate |
| 16 | Gland Nut |
| 17 | Rewinding 100 HP motor |
| 18 | Motor bearing 6316 |
| 19 | Motor bearing 29324 |
| 20 | Transportation arrangement of V.T. pump set for site to work shop and back |
| 21 | Removing of 100 HP pump set for repairs from jack well |
| 22 | Disassembling of V.T. pump set in work shop |
| 23 | Errection of V.T. pump set on jack well after repairs and giving test and trial on load |
| 24 | Errection of 100 HP motor opening & fitting |
| 25 | Bowl assembly new Impeller Bronze |
| 26 | 100 HP Motor opening & fitting |
| 27 | II) 100 HP ATS ( Auto Transformer) |
| 28 | Contactor 225 A. Delta |
| 29 | Contactor150 A. Star |
| 30 | Single phase preventer |
| 31 | Timer |
| 32 | ATS Rewinding 100HP Motor |
| 33 | Contactor 415 MCB panel board |
| 34 | Starter contactor 225 |
| 35 | Starter contactor 150 |
| 36 | Starter contactor 125 |
| 37 | Engine Oil |
| 38 | Kitkat 200 Amp |
| 39 | 100 HP terminal plate |
| 40 | N.O.C. |
| 41 | Relay 100Hp |
| 42 | Copper Luggs 90 mm |
| 43 | Copper Luggs 70 mm |
| 44 | Copper Luggs 50 mm |
| 45 | Copper fuse wire |
| 46 | 100 Hp Contactor 225 |
| 47 | 100 Hp Contactor 150 |
| 48 | 100 Hp Contactor 125 |
| 49 | 200 MCB |
| 50 | 150 MCB |
| 51 | 125 MCB |
| 52 | Copper wire 30mm |
| 53 | Copper wire 20mm |
| 54 | Copper wire 10mm |
| 55 | Brass nut bolt 12 mm |
| 56 | Brass nut bolt 10 mm |
| 57 | NO. NC ( MNX ) |
| 58 | Bus bar copper patty |
| 59 | Bus bar Holder |
| 60 | Over load relay |
| 61 | Transformer oil |
| 62 | Indicator |
| 63 | Push bottom on-off |
| 64 | Sensor rod |
| 65 | Volt meter 4” |
| 66 | Ampere meter 4” 0 to 150 Amp |
| 67 | P.T. coil |
| 68 | C.T. coil |
| 69 | Emergency stop |
| 70 | Controlling wiring |
| 71 | Power wiring for 200 Amp |
| 72 | III) Repairs of 75 HP VT ( Oil Lubricating) pump set |
| 73 | 75 HP Motor opening and fitting |
| 74 | Providing and fixing G.M. screw bearing as per sample with oil grove |
| 75 | Providing and fixing G.M. bearing big size as per sample |
| 76 | Providing and fixing T.T. plate as per sample |
| 77 | Providing and fixing T.T. Plate bushes as per sample |
| 78 | Line shaft cleaning throwing on lathe machine |
| 79 | 50mm dia Tube cleaning throwing in work shop |
| 80 | Providing and fixing rubber spider/ture supported 200mm dia |
| 81 | Providing and fixing TVS not bolts for cloning assembly |
| 82 | Providing and fixing rubber packing/flange rubber joints |
| 83 | Providing and fixing S.S. shaft couplings as per sample |
| 84 | Removing of 75 HP VT pump set for repairs form jack well ( LB-7-P-87 ) |
| 85 | Disassembling of V.T. pump set/Bowl assembly in work shop for repairs ( LB-7-P-87 ) |
| 86 | Providing and fixing impeller neck ring as per sample |
| 87 | Providing and fixing bowl assembly G.M. bushes as per sample |
| 88 | Providing and fixing bowl assembly rubber bushes |
| 89 | Providing and fixing Bowl assembly upper and lower bushes |
| 90 | Providing and fixing of impeller shaft of size s.s. 410 as per sample |
| 91 | Providing and fixing EN 8 top shaft of size as per sample |
| 92 | Providing fixing line shaft EN 8 New 38mm dia 5 feet |
| 93 | Assembly of Bowl assembly/pump in work shop |
| 94 | Errection of VT pump set/moor on jack well after repairs and giving test trial on load |
| 95 | Making transportation arrangement of VT pump set from site to work shop and back |
| 96 | Providing and fixing 50mm dia shaft enclosing tube for top shaft |
| 97 | Rewinding of 75 HP motor ( V.T. ) |
| 98 | 75 HP motor bearing NO. 29324 |
| 99 | 75 HP motor bearing NO. 6316 |
| 100 | Impeller Bowl assembly ( V.T. ) Gun metal emplier |
| 101 | IV) Repairs 75 HP V.T. pump Oil Starter |
| 102 | Contact moveable |
| 103 | Contact fixed |
| 104 | Holding coil 440 V |
| 105 | Transformer Oil |
| 106 | Connection rod |
| 107 | Movable contact patty copper luges |
| 108 | Starter wiring & repairing charges |
| 109 | V) 75 HP submersible motor pumps repairing |
| 110 | Submersible motor rewiding |
| 111 | Rutter bush bronze new |
| 112 | Rutter grinding & cutting |
| 113 | 75 HP motor thrust bearing upper & lower |
| 114 | Pump S.S. sleeves |
| 115 | Boll rubber bush |
| 116 | Gun metal bush |
| 117 | S.S. shaft 410 |
| 118 | Submersible pump opening & refitting |
| 119 | Making transportation arrangement of submersible motor & pump set from site to work shop and back |
| 120 | Errection of submersible pump set/motor on jack well after repairs and giving test trial on load |
| 121 | Pump Impeller |
| 122 | VI) 75 HP submersible motor Starter repairing |
| 123 | Contact moveable |
| 124 | Contact fixed |
| 125 | Holding coil 440 V |
| 126 | Transformer Oil |
| 127 | Connection rod |
| 128 | Movable contact patty copper luges |
| 129 | Starter wiring & repairing charges |
| 130 | VII) 75 HP VT ( Water lubricating ) pump repairing |
| 131 | 75 HP Bowl Assembly SS shaft |
| 132 | 75 HP Bowl Assembly Gunmetal Impeller |
| 133 | 75 HP Impeller neck ring gunmetal |
| 134 | 75 HP Providing and fixing bowl assembly |
| 135 | 75 HP Gunmetal bush |
| 136 | 75 HP Bowl assembly rubber bush |
| 137 | 75 HP SS line shaft |
| 138 | 75 HP SS line shaft sleeve |
| 139 | 75 HP line shaft coupling |
| 140 | 75 HP Gunmetal spider |
| 141 | 75 HP spider rubber bush |
| 142 | 75 HP bowl assembly TVS bolt |
| 143 | 75 HP casing pipe nut bolt TVS |
| 144 | 75 HP casing pipe rubber seat |
| 145 | 75 HP TT plate |
| 146 | 75 HP Gun metal Gland |
| 147 | 75 HP Motor Rewinding( Without Return Copper wire scrap material ) |
| 148 | 75 HP Motor Rewinding(Return Copper wire scrap material ) |
| 149 | 75 HP Motor Bearings 6316 |
| 150 | 75 HP Motor Bearings 29324 |
| 151 | 75 HP Transport VT pump set site to workshop and return to site |
| 152 | ATS Rewinding( Without Return Copper wire scrap material ) |
| 153 | ATS Rewinding(Return Copper wire scrap material ) |
| 154 | VIII) Valve Repairing |
| 155 | 300 MM Sluice valve |
| 156 | 200 MM Sluice valve |
| 157 | 150 MM Sluice valve |
| 158 | 100 MM Sluice valve |
| 159 | IX) 25HP Air blower, Starter and Motor |
| 160 | 25 HP Motor Rewinding( Without Return Copper wire scrap material ) |
| 161 | 25 HP Motor Rewinding(Return Copper wire scrap material ) |
| 162 | 25 HP ATS starter repair |
| 163 | 25 Air blower repair |
| 164 | New Column Pipe with flange 200MM |
