Tender For Under The Development Of Tourist Places Of Jhansi District, Tourism Development Work Of Kila Lahar Thakur Pura Complex, Driveway (1500sqm), Pathway (500 Sq.mt),Parking Area (500Sqmt) STONE BENCH (14nos), DUSTBIN (4nos) & SIGNAGE (2nos) & INFORMATION BOARD (2NOS), Clearing jungle including uprooting of rank vegetation. grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area deared. Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan). including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. PCC WORK Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level: 1:4.8 (1 cement: 4 coarse sand (zone-i) derived from natural sources: B graded stone aggregate 40 mm nominal size derived from natural sources) Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work sile, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 Brick work with common bunt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand) Brick work with common burnt clay F.P.S. (non modular bricks of dass designation-7.5 in Super Structure above plinth level upto floor V level in all shapes and size in Cement mortar 14 (1 cement: 4 coarse sand) Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cernent mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement 2 stone dust) with an admixture of pigment matching the stone shade (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately): Red sand stone exposed face fine dressed with rough backing 30 mm thick, Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Fastener with threaded dia 12 mm, Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required, Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cerment 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete st all levels Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm. Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Engraving letters in hard stone Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement: 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement 2 stone dust) with an admixture of pigment matching the stone shade Red sand stone Extra for stone work ashlar sunk or moulded or sunk and moulded or carved in: Triangular or Square or rectangular pillars Extra for stone work ashlar sunk or moulded or sunk and moulded or carved in: Circular or polygonal pillars Extra for stone work ashlar sunk or moulded in cornices. FLOORING WORK 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement: 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattem, finishing and sweeping extra sand complete all as per direction of Engineer-inCharge. 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattem., Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-charge). Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied 1.67 Itr/10 sqm over and including priming coat of exterior primer applled @ 0.90 litre/10 sqm) Finishing walls with textured exterior paint of required shade New work (Two or more coats applied @ 3.28 /10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm ELCTRICAL WORK Supply & fixing of 7mtr Gl octagonal Pole having top dia 70mm, bottom dia 130mm and base plate thickness 16mm and having sheet thickness of 3mm with single arm bracket, base plate 220 x 220 x 16mm, 4Nos foundation bolt 750mm length, Dia 24mm RCC foundation including the cost of foundation, foundation bolts, as required, complete in all respect as per UPPWD Schedule.(PWD S.L. No. 641), Supply of Solar AIO Single piece High pressure Die cast (LM6 Alloy) Aluminium housing appearance of Solar AIO shall be traditional Street Light, IP65 & IK08, suitable for OD 50/60mm bracket, having Min 3000 lumens, suitable for 24hrs (2 Nights) Autonomy and its backup calculation sheet shall be approved by Consultant Dimming Profile : • From Dusk – First 05hours sensor enabled with 30% brightness level • Next 05Hours sensor disabled and fixed at 30% Brightness level • Next 2hours/dawn- Sensor enabled with 30% brightness level Lithium pherrophosphate Battery capacity min 20Ah@12.8V or 256 watt hour & shall be of fresh manufactured battery (Not reused cells) Battery Temp range -20-+60°C and panel capacity min 35Wp, CRI >=70, Efficacy Min >175lm/W is MUST, system wattage should not be more than 17W ± 5%, if wattages increases then the size of battery & panel shall also be increased in similar percentage to maintain equal autonomy of the system. Life class of LED System 50000hrs@L70, LED Make - CREE/NICHIA/LUMILEDS/OSRAM. CE Certified, charger efficiency >90% and standards IEC62109-1, IEC61547, CISPR15, IEC62093, IEC61347-2-13, EN50530, IEC62384 The PV module should be made up of crystalline silicon solar cells Mono-Crystalline and must have a certificate of testing conforming to IEC 61215 Edition II / BIS 14286 & IEC 61730-1,2 IEC60598, Operating temp 0 Degree C to 50 Degree C, certifying above given prameters all reports shall be from In-house NABL or IECQ or any international accredited Laboratory, Complete luminaire/battery/panel/charge controller must be BIS accredited (If applicable) and as per UPPWD Approved Product List. Philips Model : SunStay or similar in OSRAM, Lighting technology and Trilux., TOTAL COST OF SOLAR LIGHT WORK,
