|
| 1 | Taking down the defective motor of centrifugalpump set of any make 415 volt 3 phase by dismantling the electrical connections, removing the motor from bed by decoupling from pump set at site in presence of JE E/M & Engr-in-charge, transporting to workshop, dismantling it completely, removing the burnt out winding, rewinding the same with super enameled copper wire of same gauge and with necessary insulating material, varnishing and re assembling the motor completly with all connections and fixing to the original position and coupling with pump and necessary alignment etc with two coat synthetic enamele paint including scraping old paint complete and writing MES/SM No, testing and commissioning all as directed by Engr-in-charge for following capacity :- Note: (i) A warranty of two year shall be given for satisfactory performance of motor(ii) Alternative arrangement of motor for water supply will be arranged by the contractorif the pump is not repaired within seven days of failure of motor the cost of same will be deemed included in the quoted rate of above item(iii)All the T&P items i.e. chain pully block & tripod shall be arranged by the contractorwithout claiming any extra cost. (iv)Transportation from MES pump house to work shopshall be arranged by the contractor without claiming any extra cost(v)Burnt out removed winding wire shall be property of contractor through schedule of credit. |
| 2 | Electric motor capacity 120 HP |
| 3 | Electric motor capacity 100 HP |
| 4 | Electric motor capacity 75 HP |
| 5 | Electric motor capacity 50 HP |
| 6 | Electric motor capacity 40 HP |
| 7 | Electric induction motor capacity 15 HP |
| 8 | Electric motor capacity5 HP |
| 9 | Servicing of centrifugal pump set by dismantling completely and replacing unserviceable ball bearing, shaft sleeve, gland neck ring gland rope, nut and bolts etc at site in presence of JE E/M / Engr in charge and re-assembling back the complete pump and fixing alignment to the original position and coupling with motor and necessary alignment etc with two coat of synthetic enameled paint including scraping of old paint complete and writing MES/SM No, testing and commissioning all as directed by Engr-in-charge for following capacity :- .Note : (i) Spares shall be measured and paid separatly under relavent items.(ii) A warranty of two yearshall be given for satisfactory performance of motor(iii) Alternative arrangement of pump set for water supply will be arranged by the contractorif the pump is not repaired within seven days of failure of pump the cost of same will be deemed to be included in the above item(iv)All the T&P items i.e. chain pully block & tripod shall be arranged by the contractorwithout claiming any extra cost.(v)Transportation from MES pump house to work shopshall be arranged by the contractorwithout claiming any extra cost.(a)Maintenance schedule :-(i)Checking for looseness of all the foundation and coupling nuts/bolts and rectification.Checking of leakage in gland packing, shifting base, bushes sluice valves, gate valves etc and rectification.(ii)Checking for any undue noise of motor pump and rectification. (iii)Checking for proper aligment and rectification. (iv)Checking for proper lubrication in bearing and lubricating. |
| 10 | 120 HP pump set |
| 11 | 100 HP pump set |
| 12 | 75 HP pump set |
| 13 | 50 HP pump set |
| 14 | 40 HP pump set |
| 15 | 15 HP pump set |
| 16 | 5 HP Gear Box |
| 17 | Supply and fix in repair of impeller with nut and bolt suitable for following capacity pump set. |
| 18 | 120/100 HP pump set |
| 19 | 75 HP pump set |
| 20 | 50/40 HP pump set |
| 21 | 15 HP pump set |
| 22 | 5 HP pump set |
| 23 | M&L for Remetaling of pump Shaftby welding & machining works and finishing complete for following pump set, complete all as specified and directed. |
| 24 | 120/100 HP pump set |
| 25 | 75 HP pump set |
| 26 | 50/40 HP pump set |
| 27 | 15 HP pump set |
| 28 | 5 HP pump set |
| 29 | Supply and fix in repair of the following spares parts as per the existing specification, size and make, complete all as specified and directed. |
| 30 | Love and joy coupling assembly for 75/50/40 HP capacity pump set. |
| 31 | Stud bolt with rubber bush for 120/100 HP capacity pump set |
| 32 | Rubber coupling for 75/50/40 HP capacity pump set. |
| 33 | Ball bearing No- N 308, Make- SKF/Fag/NBC |
| 34 | Ball bearing No- 6306, Make- SKF/Fag/NBC |
| 35 | Ball bearing No- 6308, Make- SKF/Fag/NBC |
| 36 | Ball bearing No- 6408, Make- SKF/Fag/NBC |
| 37 | Ball bearing No- 3307, Make- SKF/Fag/NBC |
| 38 | Repair/overhauling of Gear box of Clarifocculator by dismantling completely and replacing unserviceable ball bearing, shaft sleeve, nut and bolts , Gears, V belt, pulley etc. assembling back the complete Gear box of Clarifocculator and fixing alignment to the original position and necessary alignment etc with two coat of synthetic enameled paint including scraping of old paint complete and written MES/SM No, testing and commissioning, complete all as specified and directed. Note : (i) Spares shall be measured and paid separatly under relavent items.(ii) Painting and writting including item rate. |
| 39 | Gear oil (Recommended oil grade is CASTROL HYOY B90/ SERVO GEAR SUPER90/ HP GEAR OIL X- P90/ BP SPIROL SUPER 90 EP for Gear box of Clarifocculator. |
| 40 | Oil seal , Gasket for gear box of clarifocculator. |
| 41 | V Belt 02 Nos For 5 HP Motor of Gear Box |
| 42 | Lifting/Lowering oftheheavy duty flanged column pipe of 80mm to150 mm bore length not exceeding 100 mtr existing size etc. by dismantling the bolts nuts washers, rubber flangedetc and supply and fixing the serviceable nut, bolts, washer, rubber joint complete with taking out and lowering of submersible pump set along with the submersible cable, complete all as specified and directed. |
| 43 | Supply and fix MS Nuts, bolts & washers of suitable size matching with the existing flange of borewell, complete all as specified and directed. |
| 44 | Suply and fix in repair of Rubber gascket of size 150 mm dia duly drilled holes as per site requirement, complete all as specified and directed. |
| 45 | Suply and fix in repair of Rubber gascket of size 80 mm dia duly drilled holes as per site requirement, complete all as specified and directed. |
| 46 | M&L for Disconnectinng and dismantling unserviceble submersible pumping set of following capacityfrom bore well and dismantling pump motor set at site in presence of JE E/M, Engr-in-charge for checking complete carrying pump motor set to repair workshop for repair of pump set with replacement of unserviceable pump parts/spares parts and fixing serviceable parts complete reassembling & reconnecting to MS column pipes of existing size and testing and commissioning all as directed by Engr-in-charge for following capacity.Note : (i) Spares shall be measured and paid separatly under relavent items.(ii) A warranty of two yearshall be given for satisfactory performance of motor(iii) Alternative arrangement of pump set for water supply will be arrange by the contractorif the pump is not repaired within seven days of failure of pump the cost of same will be deemed to be included in the above item(iv)All the T&P items i.e. chain pully block & tripart shall be arrange by the contractorwithout claiming any extra cost. (v)Transportation from MES pump house work shopshall be arrange by the contractorwithout claiming any extra cost. |
| 47 | 50HP submersible pump |
| 48 | 15 HP submersible pump |
| 49 | 10 HP submersible pump |
| 50 | M&L for Rewinding of Submersible pump motor with heavy duty ISI marked superior quality water proof rewinding wire of suitable gauge for50HP submersible pump set including replacement of insulating materials and water proof cable joint 25 Sqmm 3 core, flat- 02 Nos, complete all as specified and directed. |
| 51 | M&L for Rewinding of Submersible pump motor with heavy duty ISI marked superior quality water proof rewinding wire of suitable gauge for15HP submersible pump set including replacement of insulating materials and water proof cable joint 16 Sqmm 3 core, flat- 02 Nos, complete all as specified and directed. |
| 52 | M&L for Rewinding of Submersible pump motor with heavy duty ISI marked superior quality water proof rewinding wire of suitable gauge for10 HP submersible pump set including replacement of insulating materials and water proof cable joint 16 Sqmm 3 core flat- 02 Nos, complete all as specified and directed. |
| 53 | M&L for Remetaling of pump Shaftby welding & machining works and finishing complete for50HP submersible pump set, complete all as specified and directed. |
| 54 | M&L for Remetaling of pump Shaftby welding & machining works and finishing complete for15 HP submersible pump set, complete all as specified and directed. |
| 55 | M&L for Remetaling of pump Shaftby welding & machining works and finishing complete for10 HP submersible pump set complete all as specified and directed. |
| 56 | M&L for Neckering of pump casing bowl by machining works and finishing complete for50 HP submersible pump set complete all as specified and directed. |
| 57 | M&L for Neckering of pump casing bowl by machining works and finishing complete for 15 HP submersible pump set complete all as specified and directed. |
| 58 | M&L for Neckering of pump casing bowlby machining works and finishingcomplete for 10 HP submersible pump set complete all as specified and directed. |
| 59 | S&F in repair Upper lower bushing suitable for 50 HP submersible pump set, complete all as specified and directed. |
| 60 | S&F in repair Upper lower bushing suitable for 15 HP submersible pump set, complete all as specified and directed. |
| 61 | S&F in repair Upper lower bushing suitable for 10 HP submersible pump set, complete all as specified and directed. |
| 62 | S&F in repair SS key with nut and bolts set suitable for 50 HP submersible pump set, complete all as specified and directed. |
| 63 | S&F in repair SS key with nut and bolts set suitable for 15 HP submersible pump set, complete all as specified and directed. |
| 64 | S&F in repair SS key with nut and bolts set suitable for 10 HP submersible pump set, complete all as specified and directed. |
| 65 | Supply, fixing and testing in repair the ERW Sreel heavy duty suction pipe both end flanged of 150 mm diaset suitable for suction pipe of centrifugal pumps installed at main pump house, complete all as specified and directed. |
| 66 | Supply and fixing in repair Ductile iron fittings for bends, Tapers, Tee pieces (single & double branch) any type and angle/radius and straight connecting pieces but all ends flanged, of size up to 150mm bore, complete all as specified and directed. |
| 67 | Supply and fix in repair DI resilient sluice valve flange type of 300 mm dia PN 1.6 grade with epoxy coated stainless steel spindle& brass check nut (non raising spindle type conforming to IS - 14846) including fixing to pipe line with nuts, bolt and washers, rubber gaseket(neouprene), complete all as specified and directed. |
| 68 | Supply and fix in repair DI resilient sluice valve flange type of 150 mm dia PN 1.6 grade with epoxy coated stainless steel spindle& brass check nut (non raising spindle type conforming to IS - 14846) including fixing to pipe line with nuts, bolt and washers, rubber gaseket(neouprene), complete all as specified and directed. |
| 69 | Supply and fix in repair DI Non return valve (Reflux), flanged ends, swing type of size 150 mm confirming to IS:5312, ISI marked complete fitting item with jointing materials such as nuts, bolts, washers and rubber gasket etc of suitable size, complete all as specified and directed. |
| 70 | Supply and fix in repair DI Non return valve (Reflux), flanged ends, swing type of size 100 mm confirming to IS:5312, ISI marked including complete fitting item with jointing materials such as nuts, bolts, washers and rubber gasket etc of suitable size complete all as direcetd. |
| 71 | Supply and fix in repair DI foot valve (Reflux), flanged ends, ball type of size 150mm confirming to IS:5312, ISI marked including complete fitting item with jointing materials such as nuts, bolts, washers and rubber gasket etc of suitable size complete all as direcetd. |
| 72 | Supply and fix in repair CI wafer type check valve (NRV), single plate, PN 1.6 of size 150mm confirming to IS:5312, ISI markedincluding one no 150mm flange and complete fitting item with jointing materials such as nuts, bolts, washers and rubber gasket etc of suitable size complete all as direcetd. |
| 73 | Repair / overhauling of electrical panel board including replacement of following defective parts such as volt meter Ammeter , starters, indicating lamps with wiring etc |
| 74 | S&F in repair 3 Ph LED Ammeter of flush mounting 96 mm x 96 mm square flush patternwith selector switch, Make L&T, Cat No. WL131010OOOO or equivalent make as specified in CA. |
| 75 | S&F in repair CT cast resin type suitable for 3 Ph LED Ammeter, of suitable VA burden, complete all as specified and directed |
| 76 | S&F in repair 3 Ph LED Voltmeter 0-500 Volts 96 x96 mm square flush patternwith selector switch, complete all as specified and directed. |
| 77 | S&F in repair Indicator lamps of RYB colors with holder 15 mm screw type, complete all as specified and directed |
| 78 | Supply and fix fully automatic star delta starter for 10 HP Motor in sheet - steel enclosure with single phase protection feature (motor rating AC-3 Duty, 415V, 50 Hz, 3-Ph), Relay Max Range 9-14A, complete all as specified and directed. |
| 79 | Supply and fix fully automatic star delta starter for 15 HP Motor in sheet - steel enclosure with single phase protection feature (motor rating AC-3 Duty, 415V, 50 Hz, 3-Ph), Relay Max Range 13-18A, complete all as specified and directed. |
| 80 | Supply and fix fully automatic star delta starter for 50 HP Motor in sheet - steel enclosure with single phase protection feature (motor rating AC-3 Duty, 415V, 50 Hz, 3-Ph), Relay Max Range 28-42A, ML3FASD, complete all as specified and directed. |
| 81 | Supply and fix fully automatic star delta starter for 15 HP SubmersibleMotor in sheet - steel enclosure with single phase protection feature (motor rating AC-3 Duty, 415V, 50 Hz, 3-Ph), Relay Max Range 17.4-24 CPSDPAMN, complete all as specified and directed. |
| 82 | Supply and fix fully automatic star delta starter for 50 HP SubmersibleMotor in sheet - steel enclosure with single phase protection feature (motor rating AC-3 Duty, 415V, 50 Hz, 3-Ph), Relay Max Range 56.4-90A, CPSDPYCT3M, complete all as specified and directed. |
| 83 | Supply and fix 4 Polecontactors ( AC Control) having AC rating 200 A 100% RATED Add on 4 th Pole flexibility(32 A to 80 Amps AC 1), complete all as specified and directed. |
| 84 | Supply and fix 4 Polecontactors ( AC Control) having AC rating 80 A 100% RATED Add on 4 th Pole flexibility(32 A to 80 Amps AC 1), complete all as specified and directed. |
| 85 | Supply & fix in repair MCCB,4 phase, 400 Amps 36 KA for moror back-up protection, fixingto the existing panel board matching withthe existing slots, including any alteration required and with extention links properly connected to the bus bar, complete all as specified and directed. |
| 86 | Supply & fix in repair MCCB,4 phase, 250 Amps 36 KA for moror back-up protection, fixingto the existing panel board matching withthe existing slots, including any alteration required and with extention links properly connected to the bus bar, complete all as specified and directed. |
| 87 | Supply & fix in repair MCCB,4 phase, 160 Amps 36 KA for moror back-up protection, fixingto the existing panel board matching withthe existing slots, including any alteration required and with extention links properly connected to the bus bar, complete all as specified and directed. |
| 88 | Supply & fix single pointed air termination Copper rod 12mm dia, 300 mm long, complete all as specified and directed. |
| 89 | S&F test point terminal block made of gun metal or phosphhorus bronzesize 75x75x25mm, drilled and screwed including 3 Nos, 8mm dia 25mm long hexagonal head brass screws including suitable sheet metal powder coated enclosure, complete all as specified and directed. |
| 90 | Supply & fix Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, complete all as specified and directed. |
| 91 | S&F galvanised iron steel tubing, 40mm bore, light grade with all fittings fixed complete to walls and ceiling or laid under floors complete all as specified and as directed. |
| 92 | M&L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level. connecting to the Galvanised iron earth strip 32x6mm size by means of bolls, nuts, check nuts and washers of galvanised iron and earth wire protected by provision of GI light grade pipe 40mm bore including provision of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agregates with 40mm thick cover of RCC (1:2:4) type B-1 including reinforcement and one handle of 6mm dia MS bar made to shape, GI medium grade 20mm bore pipe for watering , perforated at bottom. 1.75 metre long placed on top edge of earth plate. charcoal and common salt filled 150 mm thick all around the earth plate with fixing arraangement, funnel wire mesh and including excavation earth work in any type of soil returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electical plate 3 of SSR-2009 Part-I and connecting to earth test point all as specified & directed including testing on completion. |
| 93 | Supply and Fix Electric Chain Hoist ,Hook Type Having Capacity 3 Ton and lift 6 Mtrs enclosed in Aluminium alloy body along withn Push button Pendant equpped with phase sequence Protector, complete all as specified and directed. |
| 94 | S&F in repair Flat Three Core PVC Insulated & PVC Sheathed Industrial Cable for Submersible Pump Motors of size 25 sqmm 3 core 1100 volt, confirming to IS 694, complete all as specified and directed. |
| 95 | Schedule of Credit |
