|
| 1 | Material and labour in repair / maintenance / servicing / overhauling to DG set having capacity 10 KVA to 100 KVA installed at pump house / site complete with entire cleaning, checking of fuel pipe, lubricant oil pipe, rubber hose, panel wiring, fan belt, earthing strip, nut, bolts, exhaust pipe, battery pads, radiator hose, measuring instruments and tightening all nuts, bolts, mild steel rubber hose clamps and to make the system leak proof and serviceable complete with including painting to entire DG set with heat resistant smoke grey synthetic enamelled paint and base frame channel with black paints including replacement of fuel filter elements all types as under and minor spare parts, nuts, washer, radiator top capacity, battery terminal brass bolts type and changing engine oil including cleaning to oil sump and testing on full load after servicing complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately. |
| 2 | Supply only fuel filter primary with \"O\" ring complete all as specified and as directed. |
| 3 | Supply only fuel filter secondary with \"O\" ring complete all as specified and as directed. |
| 4 | Supply only lubricant oil filter with \"O\" ring complete all as specified and as directed. |
| 5 | Supply only lubricant oil by pass filter with \"O\" ring complete all as specified and as directed. |
| 6 | Supply only air cleaner element complete all as specified and as directed. |
| 7 | Supply only fan belt set for radiator, alternator and water pump etc. complete all as specified and as directed. |
| 8 | Supply only battery lead copper heavy duty having length 1.5 metre each complete with one side banjo bolt and other side brass battery terminal bolt type set of 2 pieces complete all as specified and as directed. |
| 9 | Supply only rubber hose pipe for radiator, water pump, set of 01 RM complete with mild steel clamp of suitable size complete all as specified and as directed. |
| 10 | Repair / servicing of self starter 12 volts DC complete with and including replacement burnt / unserviceable spare parts, clutch assembly, carbon brush, solenoid switch, plunger, armature and refix in repairing for DG set 10 KVA to 100 KVA complete all as specified and as directed. |
| 11 | Dismantling / repair / overhauling of water pump assembly of DG set upto 100 KVA by replacing defective parts like pump, shaft, impeller cast iron, mechanical seal, water set gasket, hub for pulley, set screw, bearing grooves nuts, spacers and spring washer and metling / machine work if any and refix in repairing after repair complete all as specified and as directed. |
| 12 | Dismantling / repair / overhauling of charging alternator (dynamo) of DG set having capacity of 10 KVA to 100 KVA and replacement of unserviceable / defective parts like carbon brushes, bearing, pulley, spacer, commutator assembly, armature, washer etc. and refitting after repair complete all as specified and as directed. |
| 13 | Material and labour in repair of engine oil servo super grade 20/40W of indian oil including cleaning of oil sump thoroughly complete all as specified and as directed. |
| 14 | Dismantling / taking down radiator assembly for repair / servicing of DG set 10 KVA to 100 KVA and carry out complete internal cleaning, brazzing to tubing and rectification of leakage and refitting including replacement of minor spare parts like inlet / outlet rubber hose with mild steel clamps, pipe for thermostat to radiator washer, nut, bolts complete all as specified and directed. |
| 15 | Disconnecting FIP pump of DG set of following capacity and carry out complete servicing / calliberation from authorised service centre and refitting after calliberation including replacement of injector nozzle, delivery valves, gasket, fuel pump gear, flange assembly, plunger, copper washer, adaptor, set both etc. as required to make the FIP serviceable complete all as specified and as directed. |
| 16 | DG set capacity 10 KVA to 63 KVA complete all as specified and directed. |
| 17 | DG set capacity 70 KVA to 100 KVA complete all as specified and directed. |
| 18 | Supply and fixing in repair self starter of 12 volts 180 AH heavy duty suitable for DG set 10 KVA to 63 KVA, 70 KVA to 100 KVA complete all as specified and directed. |
| 19 | Supply and fixing in repair self starter of 24 volts 180 AH heavy duty suitable for DG set 10 KVA to 63 KVA, 70 KVA to 100 KVA complete all as specified and directed. |
| 20 | Supply and fixing in repair of battery charger heavy duty, 150/180 AH, 24 volts with lead, volt/Amp meter complete all as specified and directed. |
| 21 | Supply and fixing in repair set of high pressure of fuel pipe of engine complete nut, set volt, clamp and spring washer etc complete all as specified and directed. |
| 22 | Supply and fixing in repair of oil sump gasket complete all as specified and directed. |
| 23 | Supply and fixing in repair of water temp switch suitable for DG set 10 KVA to 100 KVA complete all as specified and directed. |
| 24 | Supply and fixing in repair of AVR suitable for DG set 10 KVA to 100 KVA complete all as specified and directed. |
| 25 | Supply and fixing in repair of diode and rectifier for alternator suitable for DG set 10 KVA to 100 KVA complete all as specified and directed. |
| 26 | Supply and fixing in repair of OFF load open execution change over switch 4 pole 415 volts 100 Amp in sheet steel enclosure conforming to IS with side operated handle complete with fix in repairing on wall and angle iron bracket of size 40x40x6mm thick as per size requirement or complete all as specified and directed. |
| 27 | Supply and fixing in repair of OFF load open execution change over switch 4 pole 415 volts 160 Amp in sheet steel enclosure conforming to IS with side operated handle complete with fix in repairing on wall and angle iron bracket of size 40x40x6mm thick as per size requirement or complete all as specified and directed. |
| 28 | Supply and fixing in repair of OFF load open execution change over switch 4 pole 415 volts 200 Amp in sheet steel enclosure conforming to IS with side operated handle complete with fix in repairing on wall and angle iron bracket of size 40x40x6mm thick as per size requirement or complete all as specified and directed. |
| 29 | Labour for dismantling to alternator from the engine of capacity 10 KVA to 100 KVA by opening nut and bolt and transport to workshop for repair / maint and rewinding with super enamelled heat resistant copper winding wire of existing size and no\"s of turn complete with insulating material i.e. varnishing, bamboo strips, cotton thread / tape, leather paper etc and drying the winding complete with checking, realignment, welding, grinding, earth work and polishing the alternator rotor shaft and refitting the alternator with engine after repair / rewinding and testing on full load complete all as specified and directed.Note: - Copper winding wire will be measured and paid separately. |
| 30 | Rewinding coil of alternator 10 KVA to 100 KVA with super enamelled heat resistant copper winding wire of existing size and no. of turn conforming to ISI complete all as specified and directed. |
| 31 | Material and labour in repair of unserviceable ball bearing of alternator heavy duty conforming to ISI suitable for DG set alternator 63 KVA to 100 KVA complete all as specified and directed. |
| 32 | Repair / maint / servicing to DG set control AMF panel of capacity 63 KVA to 100 KVA including replacement of internal panel wiring, automatic auto cut switch with relay, sensor unit multifunctional digital meter and make the panel serviceable and testing complete all as specified and directed. |
| 33 | Material and labour in repair of unserviceable battery 12 volt 150 AH suitable for DG set 63 KVA to 100 KVA complete all as specified and directed. |
| 34 | Material and labour in repair of unserviceable battery 12 volt 120 AH suitable for DG set 63 KVA to 100 KVA complete all as specified and directed. |
| 35 | Material and labour in repair of unserviceable speed controller with auto cut sensor unit for DG set capacity 63 KVA to 100 KVA complete all as specified and directed. |
| 36 | Dismantling all incoming / outgoing electric connection carefully of transformer, voltage stabilizer, LT panel, switch, change over etc and repair the cable, fix in repaired properly with proper aluminium thimble / lugs including preparation of cable end for jointing (incoming / outgoing cable connection for each cable will be measured as one job each) thimble shall be measured separately under respective items complete all as specified and directed. |
| 37 | Labour for disconnecting all incoming / outgoing electric connection carefully of fully automatic servo voltage stabilizer having capacity 20 to 100 KVA and transport to workshop for repair / servicing and including dismantling top cover of stabilizer and taking out the coil, drain out the transformer oil and refilling after dehydration of transformer oil, cleaning internally, including replacement of unserviceable body nut, bolts, washers, top gasket of cork sheet 6mm thick, replacement of internal circuit wiring if any suitable size of copper wire and painting of stabilizer with heat resistant smoke grey synthetic enamelled paint including preparation of old rusted surfaces and writing MES NO, SM MES No, capacity, Ser No, Location etc and reinstallation / connecting electric connection with replacement of proper size aluminium lugs and testing on full load at site complete all as specified and directed. |
| 38 | Supply and fixing in repair synchronous motor single phase 230 Volt suitable for servo voltage stabilizer having capacity 20 to 100 KVA complete all as specified and directed. |
| 39 | Supply and fixing in repair PCB suitable for servo voltage stabilizer having capacity 20 to 100 KVA complete all as specified and directed. |
| 40 | Supply and fixing in repair dimmer motor suitable for servo voltage stabilizer capacity 20 to 100 KVA complete all as specified and directed. |
| 41 | Supply and fixing in repair toggle On / Off switches for stabilizer capacity 20 to 100 KVA complete all as specified and directed. |
| 42 | Supply and fixing in repair Volt meter 0-500 Amp 96mm square type 3 phase 230 volt 50 Hz complete all as specified and directed. |
| 43 | Supply and fixing in repair Ampere meter 0-400 Amp, 96mm square type 3 phase 230 volt 50 Hz with CT of suitable ratio complete all as specified and directed. |
| 44 | Supply and fixing in repair selector switch for volt / Ampere meter suitable for capacity upto 100 KVA complete all as specified and directed. |
| 45 | Supply and fixing in repair gun metal gate or globe valve 20 mm for drain out of oil complete all as specified and as directed. |
| 46 | Supply and fixing in repair unserviceable brass / gun metal stud bush suitable for 20 to 100 KVA complete with connecting rod of suitable length and dia with necessary nut, bolt, washer, bushing packing to prevent the leakage from bushes and necessary connection complete all as specified and as directed. |
| 47 | Dehydration of transformer oil and dielectric strength of oil achieved not to be less than 40 KV at 2.5 mm gap complete all as specified and as directed. |
| 48 | Supply and filling of new transformer oil for top up upto automatic servo voltage stabilizer including heating and dielectric strength not to be less than 60 KV complete all as specified and as directed. |
| 49 | Taking out main coil of voltage stabilizer 20 to 100 KVA for repair / rewinding with super enamalled copper winding wire of existing gauge including PVC insulated sheet sleeve, varnishing etc all as required and refix in repairing to the stabilizer after testing all as required at site or all as specified and as directed by Engineer-in-Charge. |
| 50 | Supply and fixing in repair MCCB TPN 250 Amps, 415 Volts, 25 KA, 4 Pole, Ics=100% Icu, overload adjustable short circuit adjustable type including complete connection all as specified and as per directions of Engineer-in-Charge. |
| 51 | Supply and fixing in repair MCCB TPN 160 Amps, 415 Volts, 25 KA, 4 Pole, Ics=100% Icu, overload adjustable short circuit fix in repaired type including complete connection all as specified and as per directions of Engineer-in-Charge. |
| 52 | Supply and fixing in repair MCCB TPN 100 Amps, 415 Volts, 16 KA, 4 Pole, Ics=100% Icu, overload adjustable short circuit fix in repaired type including complete connection all as specified and as per directions of Engineer-in-Charge. |
| 53 | Supply and fixing in repair MCCB TPN 63 Amps, 415 Volts, 10 KA, 4 Pole, Ics=100% Icu, overload adjustable short circuit fix in repaired type including complete connection all as specified and as per directions of Engineer-in-Charge. |
| 54 | Material and labour in repair of earthing complete with galvanized steel plate earth electrode 60cm x 60cm x 6mm thick buried in ground vertically to a depth not less than 1.5 metre below normal ground level connected to galvanized iron strip of 25x4 mm dia earth strip by means of bolts, nuts and washers made of galvanized iron protected by 40mm bore light grade GI pipe up 7.5 RM with earth strip and connected for body earthing of feeder pillar box all as specified and including PCC (1:3:6) type C-2 pit and precast RCC (1:1 ½ : 3) type A-1 pit cover slab of size 300x300x50mm with handle as shown in drawing funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal and salt in alternate layers including necessary earth work and excavation in hard / dense soil and removal etc complete all as specified in electrical plate No 3 of SSR Part - I 2020 all as directed. |
| 55 | Disconnecting and taking out defective underground cable in any size and any type from trenches, pole, pipe, floor, wall etc complete all as specified and as directed. |
| 56 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm 3½ core complete all as specified and as directed. |
| 57 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm 3½ core complete all as specified and as directed. |
| 58 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3½ core complete all as specified and as directed. |
| 59 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3½ core complete all as specified and as directed. |
| 60 | Supply, laying and testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3½ core complete all as specified and as directed. |
| 61 | Repair / maintenance / servicing of 175 KLD sewage treatment plant with dismantling of all connected valves and refix in repair after greasing / oiling, taking down and cleaning of all mild steel / galvanized iron pipes of any size approximate length 150 RM, cleaning of MBBR tanks both cylindrical and rectangular, cleaning bleaching chamber, cleaning of foot valves of sucking monoblock pumps complete all as specified and as directed. |
| 62 | Replacement of multifunctional valve for ACF / DMF midas 50 NB suitable size and make for existing ACF and DMF filters complete all as specified and as directed. |
| 63 | Replacement of mild steel pipe 80mm dia with all connected fittings complete all as specified and as directed. |
| 64 | Replacement of non clog vertical sub pump 3 HP, 230 Volt with chrome steel impeller and cutter, non clog to pass 40 mm size particles, submersible cable 6 Sqmm 2 core - 60 RM, installation with NRV, laying of mild steel pipe 40 mm dia upto MBBR chamber complete all as specified and as directed. |
| 65 | Replacement of brass material butterfly valve 50 mm dia complete all as specified and as directed. |
| 66 | Replacement of brass material butterfly valve 80 mm dia complete all as specified and as directed. |
| 67 | Replacement / repair of ACF / DMF materials suitable for 175 KLD STP including new filling of crushed gravel, pebbles, filtering sand media with anthracite coal, filling of the same, reactivate the ACF / DMF completely after servicing / maintenance complete all as specified and as directed. |
| 68 | Repair of monoblock pumping set including motor upto 3 HP and including replacement of suitable necessary parts like winding, circuits, bearing and other moving parts complete all as specified and as directed. |
| 69 | Repair of compressor system with motor upto 5 HP and including replacement of suitable necessary parts like winding, circuits, fan belts, bearing and other moving parts complete all as specified and as directed. |
| 70 | Removing of sludges / sands / waste particles from primary and secondary chambers, disposal of the waste particles to a distance 100 metre from STP cleaning of the chambers after removal of sludges and clean the entire chamber by using bleaching powder complete all as specified and as directed. |
| 71 | Supply and fixing in repair of altoch dozing system 100 litre / hour capacity installed for pre and post chlorination of treated water from STP complete all as specified and as directed by Engineer-in-Charge. |
| 72 | Material and labour in repair of Altoch Dozing pump, reciprocating chemical feeder for injecting altoch chemical 9 to 15 litre per day with adjustable setting 230 volt, 50 Hz, 1/30 HP including PE tubing of suitable length, NRV complete all as specified and as directed. |
| 73 | Material and labour in repair of Agitator motor for uniform suspension of altoch chemicals in the storage tank, 230 volt, 50 Hz complete all as specified and as directed. |
| 74 | Supply and fixing in repair indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 / 4.0 x 10-50 Sqmm complete all as specified and as directed by Engineer-in-Charge. |
| 75 | Supply and fixing in repair indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 70-150 Sqmm complete all as specified and as directed by Engineer-in-Charge. |
| 76 | Supply and fixing in repair indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 185-300 Sqmm complete all as specified and as directed by Engineer-in-Charge. |
| 77 | Supply and fixing in repair indoor / outdoor end termination joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 400 Sqmm complete all as specified and as directed by Engineer-in-Charge. |
| 78 | Supply and fixing in repair straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 / 4 x 25-50 Sqmm complete all as specified and as directed by Engineer-in-Charge.Note: - Earth work will be measured and paid separately. |
| 79 | Supply and fixing in repair straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 70-150 Sqmm complete all as specified and as directed by Engineer-in-Charge.Note: - Earth work will be measured and paid separately. |
| 80 | Supply and fixing in repair straight through joint heat shrinkable 1100 Volts for XLPE cable of size 3.5 x 185-400 Sqmm complete all as specified and as directed by Engineer-in-Charge.Note: - Earth work will be measured and paid separately. |
| 81 | Material and labour for loose filling with aggregate of gauge 40mm broken stone and boulder deposited, spread, levelling in larger not exceeding 15 cm thick, watered and ramming at E/M installation around 50 metre of transformer complete all as specified and as directed. |
| 82 | Taking down cement plaster of any description on bricks or stone walls or from concrete surface or from concrete surface and similar including racking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside the cantt area complete all as specified and as directed by Engineer-in-Charge. |
| 83 | Material and labour for rendering 10 mm thick (average) in cement mortar (1:4) on concrete surface / brick surface and similar including two or more dubbing coat, surface finished even and fair without using extra cement with necessary frame work, scaffolding for external surface complete all as specified and directed. |
| 84 | Material and labour in repair of galvanised iron pipe light grade 80 mm bore for cable protection as a guard pipe complete all as specified and as directed. |
| 85 | Material and labour in repair of galvanised iron pipe light grade 50 mm bore for cable protection as a guard pipe complete all as specified and as directed. |
| 86 | Material and labour in repair of galvanised iron pipe light grade 40 mm bore for cable protection as a guard pipe complete all as specified and as directed. |
| 87 | Material and labour in repair of tubing galvanised iron \"medium grade\" with flange ends all fittings laid in borewellsincluding taking out old unserviceable pipe of size 100 mm dia complete all as specified and directed. |
| 88 | Material and labour in repair of tubing galvanised iron \"medium grade\" with flange ends all fittings laid in borewells including taking out old unserviceable pipe of size 80 mm (2½\") dia complete all as specified and directed. |
| 89 | Material and labour in repair of tubing galvanised iron \"medium grade\" with flange ends all fittings laid in borewells including taking out old unserviceable pipe of size 63 mm (2½\") dia complete all as specified and directed. |
| 90 | Supply and fixing in repair of fully automatic star delta starter 3 phase, 415 volt, 50 Hz, suitable for submersible pumping set heavy duty with overload relay range suitable for 30 HP MU-G30 model L&T complete with provision of power contactor volt / Amp meter, push ON/OFF switch, selector switch, indicator etc. complete all as specified and as directed. |
| 91 | Supply and fixing in repair of fully automatic star delta starter 3 phase, 415 volt, 50 Hz, suitable for submersible pumping set heavy duty with overload relay range suitable for 40 HP MU-G40 model L&T complete with provision of power contactor volt / Amp meter, push ON/OFF switch, selector switch, indicator etc. complete all as specified and as directed. |
| 92 | Supply and fixing in repair of fully automatic star delta starter 3 phase, 415 volt, 50 Hz, suitable for submersible pumping set heavy duty with overload relay range suitable for 50 HP MU-G50 model L&T complete with provision of power contactor volt / Amp meter, push ON/OFF switch, selector switch, indicator etc. complete all as specified and as directed. |
| 93 | Supply and fixing in repair of fully automatic star delta starter 3 phase, 415 volt, 50 Hz, suitable for submersible pumping set heavy duty with overload relay range suitable for 75 HP MU-G75 model L&T complete with provision of power contactor volt / Amp meter, push ON/OFF switch, selector switch, indicator etc. complete all as specified and as directed. |
| 94 | Supply and fixing in repair of submersible motor rotor for 20 to 25 HP motor complete with bearing upper / lower bearing housing, sleeves, tee bolts and bush complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supply and fixing in repair of submersible motor stator for capacity 20 to 25 HP complete with thrust plate, thrust bearing with housing, studes, water seal, sand guard, rubber diaphragm with plate, sealing bush complete all as specified and directed by Engineer-in-Charge. |
| 96 | Supply and fixing in repair of submersible cable 10 Sqmm 3 core flat copper conductor heavy duty 1100 volts grade confirming to ISI including taking down of old unserviceable submersible cable complete all as specified and directed by Engineer-in-Charge. |
| 97 | Supply and fixing in repair of submersible cable 16 Sqmm 3 core flat copper conductor heavy duty 1100 volts grade confirming to ISI including taking down of old unserviceable submersible cable complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply and fixing in repair of submersible cable 25 Sqmm 3 core flat copper conductor heavy duty 1100 volts grade confirming to ISI including taking down of old unserviceable submersible cable complete all as specified and directed by Engineer-in-Charge. |
| 99 | Transporting air compressor and other allied equipment / material at site of tube well and installation of complete machinery for redevelopment of tube well complete all as specified and as directed by Engineer-in-Charge. |
| 100 | Redevelopment of tube well with air compressor of adequate capacity (not less than 250 Cfm) as per specification till the availability of sand free clear water, subject to minimum of 60 hours of operation of air compressor (60 x 4500) complete all as specified and as directed. |
| 101 | Providing of pea shaped gravel as per specification and gravel shrouding in annular space between well and linearassembly required during re-development complete all as specified and as directed. |
| 102 | Material and labour for strip opening complete submersible pumping set having capacity 20 to 50 HP any stage / discharge and dismantling all spare parts by opening studs complete with machine / lathe work / grinding / polishing and fitting of all spare parts and re-assembling / installation in position after necessary repair / replacement of unserviceable / defective spare parts complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items as under: - |
| 103 | Supply only cast iron stage bowl complete all as specified and as directed. |
| 104 | Supply only cast iron suction discharge chamber complete all as specified and as directed. |
| 105 | Supply only stainless steel neck ring complete all as specified and as directed. |
| 106 | Supply only stainless steel bowl bush complete all as specified and as directed. |
| 107 | Supply only stainless steel coupling sleeves complete all as specified and as directed. |
| 108 | Supply only cast iron impeller with key complete all as specified and as directed. |
| 109 | Supply only body studs fully threaded complete all as specified and as directed. |
| 110 | Supply only stainless steel pump shaft complete all as specified and as directed. |
| 111 | Supply only stainless steel pump shaft coupling with key complete all as specified and as directed. |
| 112 | Supply only cast iron NRV with NRV seat and cone complete all as specified and as directed. |
| 113 | Supply only stainless steel sleeves for bowl complete all as specified and as directed. |
| 114 | Supply only rubber bush complete all as specified and as directed. |
| 115 | Supply only strainer for pump complete all as specified and as directed. |
| 116 | Material and labour for strip opening to submersible motor / VT motor having capacity 20 to 50 HP and rewinding with super enamelled copper winding wire heavy duty heat resistance confirming to IS of same gauge and no\"s of turns complete with realignment of motor slots and insulating materials i.e varnishing, bamboo strips, leather papers, cotton tapes including replacement of unserviceable / defective spare parts and drying complete and re-assembling after repair / rewinding and testing at site on full head complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective item as under: - |
| 117 | Supply only thrust plate with circlip and key complete all as specified and as directed. |
| 118 | Supply only thrust plate bearing housing complete all as specified and as directed. |
| 119 | Supply only bearing for motor complete all as specified and as directed. |
| 120 | Supply only rubber oil seal complete all as specified and as directed. |
| 121 | Supply only cast iron sand guard complete all as specified and as directed. |
| 122 | Supply only rubber diaphragm with plate complete all as specified and as directed. |
| 123 | Supply only stainless steel sealing bush complete all as specified and as directed. |
| 124 | Material and labour for LT panel size (1.2 X 1.2 X 0.6 metre) having thickness of 3.15mm and inner shell made out of 2mm thick mild steel sheet and mild steel angle section 50 x 50 x 6 mm mounted on PCC (1:2:4) type B-1 platform 45 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable / openable by keys having chromium plated 19 mm dia fancy lock, “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust / vermin proof and general construction confirming to IS : 8623/93, including taking down of old unserviceable panels from site complete all as specified and as directed.Incoming: - (i) MCCB, 200 Amps, 4 Pole, 415 V, 25 KA - 01 Each, Al busbar of capacity 250 Amps - Set of three.Outgoing: - (i) MCCB, 100 Amps, 4 Pole, 415 V, 16 KA - 03 Each.(ii) Automatic star delta starter 40 to 63 Amps with SPP, OV, UV, PR, etc. - 02 Set (01 standby).(a) Digital Ammeter 0-250 A of size 96 Sqmm with selector switch - 01 No.(b) Digital Volt meter 0-500 V of size 96 Sqmm with selector switch - 01 No.(c) Indicator lamp RYB 22.5 mm dia LED type 240 volts AC with incoming including back up protection by 2 Amp MCB RYB with holder - 01 set of three.(d) CT coils of suitable ratio - 01 Set. |
| 125 | Material and labour for LT panel of size (1.2 X 1.2 X 0.6 metre) having thickness of 3.15mm and inner shell made out of 2mm thick mild steel sheet and mild steel angle section 50 x 50 x 6 mm mounted on PCC (1:2:4) type B-1 platform 45 cm above and 45 cm below the ground level, frame factory fabricated with front openable double door system and cable alloy (Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable / openable by keys having chromium plated 19 mm dia fancy lock, “U” type gasket shall be used to make the outer shell completely vermin proof suitable for 3 phase 4 wire 415 Volt, 50 Hz, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat painting having thickness not less than 100 microns provided with suitable gasket to make it dust / vermin proof and general construction confirming to IS : 8623/93, including taking down of old unserviceable panels from site complete all as specified and as directed.Incoming: - (i) MCCB, 250 Amps, 4 Pole, 415 V, 25 KA - 01 Each, Al busbar of capacity 315 Amps - Set of three.Outgoing: - (i) MCCB, 160 Amps, 4 Pole, 415 V, 16 KA - 03 Each.(ii) Automatic star delta starter 63 to 100 Amps with SPP, OV, UV, PR, etc. - 02 Set (01 Standby).(a) Digital Ammeter 0-400 A of size 96 Sqmm with selector switch - 01 No.(b) Digital Volt meter 0-500 V of size 96 Sqmm with selector switch - 01 No.(c) Indicator Lamp RYB 22.5mm dia LED type 240 volts AC with incoming including back up protection by 2 Amp MCB RYB with holder - 01 set of three.(d) CT coils of suitable ratio - 01 Set. |
| 126 | Supply and fixing Altoch chemicals of 45 Kg (drum) complete all as specified and as directed. |
| 127 | Dismantling and taking down electric motor of dozing system and shifting in workshop for repair and rewinding with super enamelled copper winding wire of same gauge and no\"s of turns complete with insulated material i.e. varnish, cotton tape, bamboo strips, emory paper and drying including replacement of unserviceable spare parts complete all as specified and as directed.Note: - Spare parts shall be measured and paid separately under respective items: - |
| 128 | Supply only motor seal complete all as specified and as directed. |
| 129 | Supply only motor bearing complete all as specified and as directed. |
| 130 | Supply only motor fan blade complete all as specified and as directed. |
| 131 | Supply only rotor shaft complete all as specified and as directed. |
| 132 | Supply only coupling complete all as specified and as directed. |
| 133 | Dismantling and taking down dozing pumping set and shifting in workshop for repair / maintenance / overhauling and reassembly after necessary repair complete with and including replacement of unserviceable / defective spare parts and testing on load at site complete all as specified and directed.Note: - Spare parts shall be measured and paid separately under respective items: - |
| 134 | Supply only Agitator assembly complete all as specified and as directed. |
| 135 | Supply only Agitator bearing complete all as specified and as directed. |
| 136 | Supply only Agitator shaft with stainless steel blade duty FRP coated complete all as specified and as directed. |
| 137 | Supply only PE tubing 5/8\"\" (8 metre) complete all as specified and as directed. |
| 138 | Supply only solenoid motor complete all as specified and as directed. |
| 139 | Supply only electronic controlled circuit plate complete all as specified and as directed. |
| 140 | Supply only injection check valve (NRV) complete all as specified and as directed. |
| 141 | Supply and fixing in repair suction sweeper head for swimming pool (pool cleaner) 36 inch long complete with wheels, PVC core nylon brush 36 inch NRV complete all as specified and all as directed. |
| 142 | Supply and fixing in repair suction flexible rubber hose pipe 80 mm dia braided type green colour conforming to ISI complete with suitable size mild steel clamp complete all as specified and as directed. |
| 143 | Repair / maintenance / service to swimming pool filteration plant complete with replacement of unserviceable spare parts fitting valves, filter media, PVC strainer, pressure gauge, butterfly valve, air vent pipe complete with cleaning internally including taking out all filter media outside and kept separately each media at site for reuse, preparing external services of filter media and make the surface smooth and applying two coats of synthetic enamel paint and a coat of red oxide compete with suction and discharge pipe and relying all filter media in proper layer duly washed and tested on full load complete all as specified and as directed. |
| 144 | Supply only water pressure gauge 10 Kg 100 mm dia complete with 3/8 inch brass sampling cock complete all as specified and as directed. |
| 145 | Supply only butterfly valve cast iron body with gun metal sheet conforming to IS : 13095 of size 150 mm dia complete all as specified and as directed. |
| 146 | Supply only superior quality copper sulphate complete all as specified and as directed. |
| 147 | Supply only superior quality crystal Alum non-ferric for swimming pool complete all as specified and as directed. |
| 148 | Supply and fixing in replacement PVC insulation patch roll for submersible cable connection complete all as specified and as directed. |
| 149 | Supply and fixing in repair of onload open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 100 Amp confirming to IS complete all as specified and directed by Engineer-in-Charge. |
| 150 | Supply and fixing in repair of onload open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 160 Amp confirming to IS complete all as specified and directed by Engineer-in-Charge. |
| 151 | Supply and fixing in repair of onload open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 200 Amp confirming to IS complete all as specified and directed by Engineer-in-Charge. |
| 152 | Supply and fixing in repair of onload open execution change over switch front handle operated 4 pole, 415 volt, 50 Hz 250 Amp confirming to IS complete all as specified and directed by Engineer-in-Charge. |
| 153 | Material and labour in repair of cast iron sluice valve PN 1.6 with iron wheel head of size 100 mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gasket 3 mm thick conforming to ISI : 14846/2000 complete all as specified and directed. |
| 154 | Material and labour in repair of cast iron sluice valve PN 1.6 with iron wheel head of size 150 mm bore with stainless steel spindle both end flanged complete with nut, bolts, washer and rubber gasket 3 mm thick conforming to ISI : 14846/2000 complete all as specified and directed. |
| 155 | Supply and fixing cast iron non return valve both end flanged and fixed to the existing pipe line including joint with nut, bolt, washers, rubber or fiber board gasket, etc testing complete all as specified and directed including taking down old one complete suitable for 150 mm dia bore of pipes. |
| 156 | Supply and fixing cast iron non return valve both end flanged and fixed to the existing pipe line including joint with nut, bolt, washers, rubber or fiber board gasket, etc testing complete all as specified and directed including taking down old one complete suitable for 100 mm dia bore of pipes. |
| 157 | Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre deep in loose / soft soil and getting out for underground cable / erection of poles, stays etc complete all as specified and as directed by Engineer-in-Charge. |
| 158 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick layers complete all as specified and as directed by Engineer-in-Charge. |
| 159 | Removal of excavated material not exceeding 50 metre away and depositing where directed at a level not exceeding 1.5 metre above from starting point complete all as specified and as directed by Engineer-in-Charge. |
| 160 | NOTE NO 1: -Samples of materials as approved will be kept in GE\"s sample room.NOTE NO 2: -All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE.NOTE NO 3: -Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings. |
