|
| 1 | ROAD PAVEMENT WORK ( BT ) |
| 2 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specifications Clause 201 for Rural Roads of MORD.By Manual Means-In area of non-thorny jungle |
| 3 | Constructions of Subgrade and Earthen ShouldersConstructions of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1 for Rural Roads of MORD. (Borrow pit /pre work post work measurement) |
| 4 | Extra for carriage of all kinds of earth by MechanicalTransport: (b) Carriage up to total lead of 2.0 km. |
| 5 | Hard Shoulder with MoorumSupplying, spreading and consolidating Moorum to a depth of 75 mmat desired density and C.B.R. as per specification with power roller to proper gradient and camber including watering as necessary, and lighting, guarding, barricading and making adequate earthen bundh where necessary to protect the edges and curing with water for 2 to 3 days, mending cracks by rolling where necessary including all incidental charges of roller, cost of fuel & lubricants etc. complete as per specification. |
| 6 | GSB : Granular Sub-base with Graded Material - By Mix in Place Method Construction of granular sub-base by providing graded material, mixing by mix in place method with Rotavator at OMC, spreading in uniform layers with Motor grader on prepared surface in proper grade and camber, compacting with vibratory roller to achieve the desired density, including lighting, guarding, barricading, including cost of all materials, machinery, tools and plants including cost of quality control complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).GSB Grading-II: |
| 7 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate, watering including lighting, guarding, barricading and making necessary earthen bundh of one metre width on each side and preparing the bed by necessary cutting or filling, including cost of all materials and hire and labour charges of all men and machinery and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).WBM: BY MANUAL MEANS:- GRADING-I Aggregate (63 mm to 45 mm) Using Stone Screening Type B (11.2 mm) & without Binding MaterialUSING PAKUR VARIETY STONE AGGREGATES |
| 8 | WBM: BY MANUAL MEANS:- GRADING-II Aggregate (53 mm to 22.4mm) Using Stone Screening Type B (11.2 mm) & without Binding Material USING PAKUR VARIETY STONE AGGREGATES¦ MATERIALS REQUIRED PER CUM OF WBM GRADE-II:- 1.45 cum i) Grading-II Aggregate (53mm to 22.4mm) : 1.21 cum ii) Stone Screening Type-B (11.2 mm): 0.24 cum |
| 9 | PRIME COATProviding and applying primer coat with Cationic Bitumen Emulsion of approved grade conforming to IS: 8887-1978 and requisite quantity on prepared surface of granular base including cleaning of road surface and spraying primer using Mechanical means including cost and carriage of bitumen emulsion and all other incidental costs of work complete as per Clause 502 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). For WBM/WMM Surface: with primer @ 0.85 kg/sqm Cationic Bituminous Emulsion Slow Settinggrade SS-1 recommended for prime coat application (Bituminous Emulsion (PACKED) MS Type from Dhulagarh) |
| 10 | TACK COATProviding and applying tack coat with Cationic Bitumen Emulsion of approved grade conforming to IS: 8887-1978 on the prepared surface cleaned with Hydraulic broom, moistening the surface including cost and carriage of emulsion, hire charges of machinery and labour, cost of fuel and lubricants all complete as per Clause 503 of Specifications for Road & Bridge Works of MoRT&H (5th Revision)On Granular surfaces treated with primer (Using Bitumen emulsion @ 0.275 kg /sqm.) Cationic Bituminous Emulsion Rapid Setting grade RS- 1 recommended for tack coat(Bituminous Emulsion (PACKED) MS Type from Dhulagarh) |
| 11 | 20MM THICK PREMIX CARPET USING VG-30 GRADE BITUMEN & MIXING WITH MOBILE HOT MIX PLANT (LIGHT DUTY) Providing, laying and rolling of Open - graded premix surfacing of 20 mm thicknesscomposed of 13.2 mm (@ 0.018 m³ per m²) and 11.2 mm (@ 0.009 m³ per m²) size stone aggregates, including thoroughly cleaning of the surface, screening, cleaning and pre-heating stone chips and fully pre-coating the same either using viscosity grade paving bitumen or cut-back or emulsion, carrying the mixture by any suitable arrangements, laying the mixture uniformly over the surface, including line, grade and level to serve as wearing course on a previously prepared base, including mixing in Mobile Hot Mix Plant (Light Duty) and thoroughly rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades including the cost and carriage of stone chips and matrix, heating the matrix, preheating the aggregates to required temperature and including the hire charges of Mobile Hot Mix Plant (Light Duty) and other machinery, pay of operators, cost of fuel and lubricants etc. complete to be followed by seal coat of either Type A or Type B as per Technical Specification Clause 508 for Rural Roads of MORD. |
| 12 | SEAL COATProviding and laying Premixed Seal Coat (Type B) with approved quality sand/grit @ 0.6 m3/ 100 m2 and bitumen binderon thoroughly cleaned black top surface coated with tack coat, including heating and mixing cleaned sand/grit (100 % passing through 2.36 mm sieve and retained on 180 micron sieve) uniformly with bitumen binder, laying and spreading the mix at an uniform rate using suitable means, brushing the surface, if necessary, to ensure uniformity, followed by rolling with power roller including the cost and carriage of binder and aggregates, cost of heating the binder and aggregates and all other incidental charges, cost of fuel and lubricants, including hire charges of machineries, tools & plants required for construction and quality control complete as per Clause 511 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).By Manual Means : Seal coat: Type B With Hot Bitumen Binder @ 6.80 kg /10 sqm [BITUMEN: VG-30 (PACKED) FROM IOCL REFINERY HALDIA] |
| 13 | ROAD PAVEMENT WORK ( CC ) |
| 14 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specifications Clause 201 for Rural Roads of MORD.By Manual Means-In area of non-thorny jungle |
| 15 | Box cutting or filling in Road embankment in all sorts of soil including spreading the spoils properly over the flank as necessary or on berm to approximate grade & camber and rolling the sub-grade with power roller to proper camber and grade as per direction and satisfaction of Engineer-in-charge including uprooting and removing plants and jungles when and where necessary.Preparation of Subgrade with Embankment & Shoulder Construction: For depth upto 300mm(a) Depth0 to 150 mm |
| 16 | (b) for depth 150 to 300 mm |
| 17 | GSB : Granular Sub-base with Graded Material - By Mix in Place Method Construction of granular sub-base by providing graded material, mixing by mix in place method with Rotavator at OMC, spreading in uniform layers with Motor grader on prepared surface in proper grade and camber, compacting with vibratory roller to achieve the desired density, including lighting, guarding, barricading, including cost of all materials, machinery, tools and plants including cost of quality control complete as per Clause 401 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). (USING PAKUR VARIETY STONE AGGREGATES) GSB Grading-II: |
| 18 | Plain / Reinforced Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications.E PCC Grade M30M-30 GRADE - USING CONCRETE MIXER: USING PAKUR VARIETY STONE AGGREGATES |
| 19 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 20 | JOINT SEALING COMPOUNDProviding and filling joint sealing compound as per drawings and technical specifications with coarse sand and 6% bitumen by weight |
| 21 | Dismantling of Cement Concrete Pavements Dismantling of cement concrete pavements bymechanical means using pneumatic tools breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials upto a lead of 1000 m, stacking serviceable and unserviceable materials separately as per Technical Specification Clause 202 for Rural Roads of MORD. |
| 22 | Removal of Unserviceable Soil with Disposal upto 1000 metres Removal of unserviceable soil including excavation, loading and disposal upto 1000 metres lead but excluding replacement by suitable soil which shall be paid separately as per Technical Specification Clause 302.3.11 for Rural Roads of MORD. (Mode of measurement: pre works and post works) |
| 23 | TRAFFIC SIGN & ROAD SAFETY WORK |
| 24 | Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc. |
| 25 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as perapproved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).The retro reflective sheeting used on the signs shall consist of white or coloured sheeting having a smooth outer surface which has the property of retro reflection over its entire surface. It shall be weather resistant and exhibit colour fastness.60 cm equilateral triangle : for Cautionary/Warning Signsfor Signage like Left/Right Curve, Hairpin Bend, Narrow Bridge, School Ahead, Series of Bends etc.: with red border and black symbol in white background[600mm side with 45mm wide border & Distance of sign from hazard =45m] |
| 26 | 60 cm Circular : for Mandatory/ Regulatory Signsfor Signage like Speed limit, Maximum load limit etc. |
| 27 | 90 cm high Octagon : Mandatory/ Regulatory Signsfor Octagonal red STOP sign |
| 28 | 60 cm x 45 cm rectangular : for Informatory/Guide SignsFacility Information: symbol within a rectangular board with blue background.For Direction and Place Identification signs: used with destination names and distances with arrows indicating the direction. White Background with Black Arrows/Border/Letters |
| 29 | R.C. Guard postSupplying fitting and fixing R.C. guard post 1.37m longwith C.C. 1:2:4 with graded stone chips of 13.2mm down casting , curing complete including cost ofproviding 4nos.of 12mm dia. rod of length 1.54m as main reinforcement and 6 nos. of round shaped 8mm dia rods used as binders; the placing of the first binder should be at 75mm below the top finished surface and the other 5 nos of binders should be placed at 245mm c/c ; the guard post is of octagonal section with inscribed circle of dia 24cm at the base tapering to corresponding dimensions of 16cm at the top including two coats of painting with best quality synthetic enamel paint of approved make and grade to form 6 nos. horizontal alternate bands in white/tannery yellow and black to 90 cm length standing up above ground after mending good damages if any during striking off shuttering, making hole in ground of47cm depth and 30cm. minimum dia, fixing the guard posts in the same holes and repacking the earth properly so as to keep the guard posts standing properly erect in correct position true to line and length including carriage of R. C. Guard Post with due care to the site including loading into the truck and unloading at site complete in all respect.With Pakur variety stone chips |
| 30 | Citizen\"s information BoardProviding and erecting direction and place identification retro- reflectorised signas per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing and Clause 801 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).Direction and Place Identification Signs with size more than 0.9 sqm size : for Citizen\"s information BoardCost of item for 2 Nos. Board at both end of the road |
| 31 | GUARD WALL |
| 32 | Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 for Rural Roads of MORD including setting out, construction of shoring and racing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. |
| 33 | Sand filling in foundation trenches and at the backof abutments, wing-walls etc. with good local sand free from earth in layers not exceeding 15 cm. including inundating each layer by profuse water and poking and ramming layer by layer complete including supply of sand. Quality of sand is to be approved by the Engineer-in-charge. |
| 34 | Supplying and laying Polythene Sheet (150mm /sq.mm) over dump proof course below floring or roof trenching or in foundation or in foundation trenches. |
| 35 | Plain / Reinforced Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement A) PCC Grade M20 Using concrete mixer. |
| 36 | Providing weep holes in Brick masonry / Plain / Reinforced concrete abutment, wing wall / returnwall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications |
| 37 | 600mm DIA PIPE CULVERT |
| 38 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD.By Manual Means - Cement Concrete |
| 39 | Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202 for Rural Roads of MORD. Upto 600 mm dia Hume pipe |
| 40 | Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 for Rural Roads of MORD including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. |
| 41 | Providing and laying Design Mix concrete for plain/ reinforced concrete work in any part of bridge (excluding bottom plugging) with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete but excluding cost of labour and materials for formwork & reinforcement works. M-15 GRADE - USING CONCRETE MIXER[Stone aggregate of Pakur variety] |
| 42 | M-20 GRADE - USING CONCRETE MIXER[Stone aggregate of Pakur variety] |
| 43 | BEDDING FOR PIPEi) Type A (Concrete Cradle) BeddingLaying concrete cradle bedding with M15 Grade Cement Concrete as per Clause 1105 (i) for Rural Roads of MORDM-15 GRADE - USING CONCRETE MIXER[Stone aggregate of Pakur variety] |
| 44 | Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single RowProviding and laying reinforced cement concrete pipe NP3 with spigot socket for culverts on first class bedding of granular material in single row including fixing with cement mortar 1:2 as per Technical Specification Clause 1106 for Rural Roads of MORD.Cost of 600mm dia NP3 Pipe |
| 45 | Supplying, spreading and compacting Sand to required thickness, in layers not exceeding 150 mm to proper gradient and camber, inundating each layer by water and packing and ramming layer by layer to achieve desired compaction, including lighting, guarding, barricading and making adequate earthen bundh where necessary, curing with water as per direction, mending cracks and depressions by ramming wherever necessary. |
| 46 | Hire and labour charges for Shuttering with or without staging upto 4.0 m height using approved stout props with wooden planks/ply wood/steel sheet plate with required bracing for any kind of plain or reinforced concrete works in all sorts of minor structure including culvert, box culvert, cross-drain etc. The rate is inclusive of fitting, fixing and striking out after completion of work as per specification and direction.SHUTTERING WORK WITH PLY/ STEEL SHEET PLATE |
| 47 | WEEP HOLESProviding weep holesin Brick masonry / Plain / Reinforced concrete abutment, wing wall / return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V:20H towards drawing face. Complete as per drawing and Technical specifications. |
| 48 | BOX CULVERT |
| 49 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removing, spreading or stacking of spoils within a lead of 150 m. as directed and including trimming the sides of the trenches, leveling, dressing and ramming the bottom, and backfilling with approved material complete as per direction of the Engineer-in-Charge .In all sorts of soil excluding marshy soil & rocks (soft or hard) by mechanical means (using excavator of suitable capacity).For depth up to 3m: Without pumping out water |
| 50 | Providing and laying Design Mix concrete for plain/ reinforced concrete work in any part of bridge (excluding bottom plugging) with coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete but excluding cost of labour and materials for formwork & reinforcement works. PCC M-15 GRADE - USING CONCRETE MIXER- WITH PAKUR VARIETY STONE AGGREGATES |
| 51 | Plain / Reinforced Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications.RCC M-25 GRADE - USING CONCRETE MIXER- WITH PAKUR VARIETY STONE AGGREGATES |
| 52 | Plain / Reinforced Cement Concrete in Substructurewith coarse aggregates of appropriate nominal size and grading, fine aggregate (sand) conforming to proper grading zone, both of approved quality, cement and water reducing admixtures, as necessary, including labour, cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge and cost for quality control, sampling, testing etc. all complete as per drawing and technical specification including the cost of necessary form work and staging complete as per drawing and technical specifications.RCC M-25 GRADE : (i) Height upto 5m - Using concrete mixer : WITH PAKUR VARIETY STONE AGGREGATES |
| 53 | Supplying, fitting and placing HYSD bar reinforcement in Bridge Foundation including initial straightening, straightening of coils bars, removal of loose rust (if any), cutting to requisite length bending, binding with annealed wire not less than 1 mm in size and conforming to IS 280 at every intersection hooked and bent to correct shape and placed on forms etc. including cost of black annealed wire and cost of loading, unloading, carriage of all steel materials complete as per drawing and technical specifications.Tor Steel rods / HYSD bars / TMT bars(SAIL/TATA/RINL) (Fe 415 /Fe 500 /Fe 500D conformsto IS: 1786) |
| 54 | Supplying, fitting and placing HYSD bar reinforcement in Bridge Sub-structure including initial straightening, straightening of coils bars, removal of loose rust (if any), cutting to requisite length bending, binding with annealed wire not less than 1 mm in size and conforming to IS 280 at every intersection hooked and bent to correct shape and placed on forms etc. including cost of black annealed wire and cost of loading, unloading, carriage of all steel materials complete as per drawing and technical specifications.Tor Steel rods / HYSD bars / TMT bars(SAIL/TATA/RINL) (Fe 415 /Fe 500 /Fe 500D conformsto IS: 1786 |
| 55 | Hire and labour charges for Shuttering with or without staging upto 4.0 m height using approved stout props with wooden planks/ply wood/steel sheet plate with required bracing for any kind of plain or reinforced concrete works in all sorts of minor structure including culvert, box culvert, cross-drain etc. The rate is inclusive of fitting, fixing and striking out after completion of work as per specification and direction.Using Ply wood (12mm thk.)/ Steel sheet plate with required bracing Where staging is not required |
| 56 | Sand filling in foundation trenches and at the backof abutments, wing-walls etc. with good local sand free from earth in layers not exceeding 15 cm. including inundating each layer by profuse water and poking and ramming layer by layer complete including supply of sand. Quality of sand is to be approved by the Engineer-in-charge. |
| 57 | Add GST@18% |
| 58 | Add Cess @1% |
