Cost Of Maintenance Work Of Elephant Proof Trench Andother Work At Mullakudy In Thekkady Range During 2024-2025.
Tender Value
2.18 Lakhs
Estimated cost
Bid Submission
03 Jun 2024
0 days left
EMD
3300
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
thekkady → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
COST OF MAINTENANCE WORK OF ELEPHANT PROOF TRENCH ANDOTHER WORK AT MULLAKUDY IN THEKKADY RANGE DURING 2024-2025.
BOQ
| Sl. No. | Item Description |
| 1 | 2.9.3Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches ordrains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soilsas directed, within a lead of 50 m.Hard rock (blasting prohibited) |
| 2 | 2.31Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared |
| 3 | 2.8.1Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundationtrenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides andramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplusexcavated soil as directed, within a lead of 50 m.All kinds of soil |
| 4 | 60.7.7 Conveyance and dumping of departmental granite stones-Conveyance of departmental granite stone 20to 45 dm3 in size from stack at site and dumping in position (60% 45m3,30%30 to 40dm3 and 10% 20 to30dm3 stones) to lines and levels to from the core of the sea wall as per approved design including allleads and lifts etc. complete as per the direction of the departmental officers at site. |
| 5 | 60.7.8DR with Departmental. Stone - DRY RUBBLE MASONRY _ Dry rubble without concrete levelling courseusing departmental rubble including packing to compactness to lines and levels, labour charges etc.complete as per direction of Departmental officers at site |
| 6 | 5.22.6Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position andbinding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 7 | 4.1.3Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mmnominal size) |
| 8 | 10.16.1Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., includingcutting, hoisting, fixing position and applying a priming coat of approved steel primer, including weldingand bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 9 | od22793/2024_2025Blacksmith 1st class |
| 10 | 12.50Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation asapproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet andpolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum toavoid scratches during transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shape wherever required. |
| 11 | 12.51.1Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinccoating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on bothside of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screwscomplete:Ridges plain (500-600 mm) |
| 12 | Lumpsum for round off |
AI Tender Summary
Tender Timeline
May 25, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedJun 03, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 05, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender