|
| 1 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) n.exc 1.50 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc. 1.50 Sqm n.exc 4 Sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each complete all as specified and directed. |
| 4 | Taking down shutters of any descriptionexc 2 Sqm each complete all as specified and directed. |
| 5 | S&F 2nd class hardwood plain solid, straight chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed. |
| 6 | Preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treating with tar or coal tar black paint at ends of post back of chowkats etc complete all as specified and directed. |
| 7 | S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 8 | M&L PCC 1:2:4 type B1(20 mm graded stone aggregate) as in bed block for embedding hold fast of doors, window frames or chowkats including necessary form work complete all as all as specified directed. |
| 9 | M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and as directed. |
| 10 | S&F 35 mm thick flush shutters solid core construction, with particle board core and ply wood face panels commercial type on both sides complete all as specified and as directed.Note :-The rate for flush shutters include for provision of suitable blocks for taking mortice locks, latches or other fittings complete. |
| 11 | S&F 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours, articles n. exc 200 Cucm each complete all as specified and directed. |
| 12 | Supply only MS butt hinges medium weight cold rolled 50 mm size all as specified and directed. |
| 13 | S&F MS butt hinges medium weight cold rolled of size 100 mm complete all as specified and as directed. |
| 14 | S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as directed. |
| 15 | S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 16 | S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . |
| 17 | S&F 150 mm SS handles cast type polished brightcomplete all as specified and directed. |
| 18 | Supply and fix in repairs door closer hydraulically regulated designation No. 3 universal type aluminium body, (diecast) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kgcomplete all as specified and directed |
| 19 | S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150 mm complete all as specified directed. |
| 20 | S&F in repairs 100 mm SS handles cast type polished brightcomplete all as specified and directed . |
| 21 | S&F in repairs 250 mm long aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 22 | S&F in repairs and stick solar control film 50 microns thick reflective type sticked to glass panes as per instructions of manufacturerscomplete all as specified and as directed. |
| 23 | S&F heavy duty floor door spring including cutting hole into the floor and packing for making good with the existing floor complete all as specified and directed including taking out old one. |
| 24 | M&L forpreparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 25 | M&L forPreparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed. |
| 26 | M&L Veneered decorative plywood 4mm thick, grade 1 (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work or fixed with adhesive ( Fevicol)complete all as specified and directed including taking out old one.. |
| 27 | M&L for french polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wooden filler on new works with two or more coats complete all as specified and directed. |
| 28 | Supply & Fix powder coated Aluminium window frame 2/3 track outer frame 92 mm x 31.75 mm x1.50 mm and guide rail of section Nos size 92 x 31.75 x1.50mm and shutter section 40 x 18 x 1.550 mm sliding type including necessary jointing cleats, glazing clips, rubberpacking handles and anodised aluminium snab beading screws etc., complete all as specified and as directed |
| 29 | S&F anodised aluminium grill, having mess size 100mmx100mm made out 6mm wide & 3mm thick aluminium section complete all as specified and directed. |
| 30 | S&F aluminium door shutter with chowkats made out of hollow aluminium sections as mentioned below, each shutter having 2 Nos ‘D’ type aluminium handles of 200mm long 2 Nos aluminium tower bolts of 150 mm long and 1 No brass mortice lock of 6 lever with key in duplicate. Shutter shall be partly glazed with 5 mm thick sheet glass ordianry quality and partly panelled with 12mm thick particle board, pre-laminated interior grade, prelaminated one side with decorative choicelamination, on other side balancing light grey lamination fixed with glazing clips, rubber beadings and aluminium beadingscomplete all as specified and directed.Chowkat size : 101.60 x 44.45 x 2.40 mm (1.608 Kg/RM appx)ShutterTop rail: 114.30 x 2.15 mm thick (1.836 Kg/RM appx)Bottom rail: 150.00 x 2.20mm thick (2.376 Kg/RM appx)Middle rail: 83.50 x 1.70 mm thick (1.243 Kg/RM appx)Vertical rail :85.00 x 1.80 mm thick(1.302 Kg/RM appx) |
| 31 | Taking down aluminnium shutters ofwindows, ventilators etcof any description not exc 1 Sqm each and refixing the same in the same opening after replacing of unserviceable screws, cleat, rubber packing, aluminum snap beading etc, and tightening complete all as specified and directed ( Note:- 1.. Quted rateis inclusive costof rubber beading, aluminum snap beading, screws, cleat etc whatever requires at site) |
| 32 | Taking down aluminnium shutters of doors, windows of any description exc 1 Sqm but not exceeding 2 sqm eachand refixing the same in the same opening after replacing of unserviceable screws, cleat, rubber packing, aluminum snap beading etc, and tightening complete all as specified and directed.Note:- .Quoted rateis inclusive costof rubber beading, aluminum snap beading, screws, cleat etc whatever requires at site) |
| 33 | Dismantling of Wall and ceiling boards/ wall partition (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets / aluminium frame workcomplete all as specified and directed. |
| 34 | M&L for partition walls with panels of 1.44 sqm (appx.) made out of aluminium anodisedhollow sections of size 63.50x38.10x1.95mm thick ,snap grid beading, rubber gasket, 5 mm thick sheet glass and 12mm thick prelaminated particle board interior grade, prelaminated one side with decorative choicelamination, on other side balancing light grey lamination fixed with aluminium beadings complete all as specified and directed.Note :-The scope work incude for taking down existing damaged aluminium door/ window/grill/panels and the unit rate quoted shall be deemed to include for the same. |
| 35 | S&F Anodised Aluminium Frame Work (snap grid) for false ceiling Work made from Anodised Aluminium main /cross tee of size not less than 38 mm x 24 mm x 1.5 mm thick and 28 mm x 24 mm x 1.5 mm thick respectively for false ceiling of grid size 600 mm x 600 mm including necessary hanging arrangement comprising of 6 mm dia MS rod, \"J\" bolts with necessary bolts, nuts and washer all as per manufacturer\"s instruction. The snap grid (main & cross section) shall be supported at ends all along the wall with Anodised Aluminium angle of size 40mmx25mmx2mm, weighing 0.36 Kg / RM. The main and cross tees shall be jointed at junction / crossings with anodized aluminium angle bracket of size 15mmxl5mmx1.5mm, weighing 0.12 Kg per running metre, fixed with suitable size mild steel, bolts nuts and washers complete as permanufacturer\"s instruction and as specified anddirected. |
| 36 | S&F12mm thick perforated particle board 60cm x60 cm in size for insulation and acoustic purposefixed with aluminium frame work in ceilingwith screws or with staples on snap grid as per manufacturer\"s instruction complete all as specified and as directed. |
| 37 | Dismantling wrought iron or MS work of any description not otherwise provided, complete all as specified and directed. |
| 38 | S&F M.S. framed work such as grills gratings etc with end of bars shouldered/or riveted or forged into spikes framed guard bar, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar works steel quality conformingto Fe-290, Grade E- 165 complete all asspecified directed . |
| 39 | M&L preparation of new or previously untreatedsteel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 40 | M&L preparation of old painted steel surface over 10 cm width or girth not otherwise described and applying a coat of synthetic enamel paint complete all as specified and directed |
| 41 | S&F for 12 mm thick toughened glassas in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes requiredcomplete all as specified and as directedincluding taking out old one. |
| 42 | Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 43 | M&L for pre-cast cement concrete 1:3:6 type C1(using 20 mm graded crushedstone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed. |
| 44 | Demolition of cement concrete( un reinforced) in ground floors and paving n exc 15 cm thickness (below or above ground level) including removingdebris out side ND(V)complete all as specified and directed. |
| 45 | M&L 75 mm thick cement concrete 1:3:6 Type C2 (using 40 mm graded crushed stone aggregate) in floors (plinth protection) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 46 | Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 47 | M&L rendering 10 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement all as specified and directed. |
| 48 | M&L rendering 15 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 49 | M&L 10 mm thick plastering in cement mortar 1:3on concrete surfaces of ceiling and finishing the surfaces fair and even without using extra cement all as specified and directed. |
| 50 | M&L for preparing newly plastered and unplastered surfaces of ceiling and applying three coats of white washing complete all as specified and directed. |
| 51 | M&L forpreparing new surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer complete all as specified and directed. |
| 52 | M & L forpreparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primercomplete all as specified and directed. |
| 53 | M & L for preparation of newly plastered surfaces of walls and applyingtwo coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primerover a coat of cement based wall putty minimun thickness 1.5mm and cutting to smooth surfaces by sand paper complete all as specified and directed. |
| 54 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises all as specified and directed. |
| 55 | Material & Labour for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match laid over and including cement screed 10 mm thick in 1:4complete all as specified and as directed. |
| 56 | Material& Labour for coloured glazed ceramic tiles (300 x 450)x 7-8 mmthickin dado set and jointed in neat cement slurry and pointed in coloured cement to match fixed over & including rendering in CM 1:3, 10 mm thick complete all as specified and as directed. |
| 57 | M&L forlight shed vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.18 sqm but notexceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 15 mm thick 1:6 cement morter including roughning surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3 kg of cementper sqmcomplete all as specified and as directed |
| 58 | M&L light shed vitrified ceramic tiles 10 mm thick (square/ rectangular) polished as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 10 mm thick 1:4 cement mortercomplete all as specified and as directed |
| 59 | M&L Granite (of any type) slab, 18 to 20 mm thick machine cut in skirting/dado laid over 15 mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishing complete all as specified and directed |
| 60 | Material & labour for rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc., complete all as specified and as directed. |
| 61 | M&L for acid resistant tiles 15mm thick vitreous unglaged, set jointed and pointed in chemical resistant mortar, resin type in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15mm thick cement mortor (1:6) screed bed complete all as specified and directed. |
| 62 | M&L for decorative (Endura tiles / stair tiles) 7 to 8 mm thickas in treads/ rise / landing of stair laid over 15 mm thick cement screed (1:6) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the tilescomplete all as specified and directed. |
| 63 | S&F aluminium composite panel of 3mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwtiched by 2.5mm polythene core with PVDF coating of 30 micron, face fully covered with high intensity prismatic (Type-IV) sheeting conforming to type-III of ASTM-D 4956-01 and fixing the same to the structural frame work by means of suitable self tapping screws, rivets or bolts and nuts and erecting in position as in roof covering, walling, column /beametc covering complete all as specified and directed.including taking out old one.Note:- Cost of aluminium frame work is deemed tobe included in the quoted rate |
| 64 | S&F factory made UPVC white colour sliding window three track of area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67 mm). Sliding mesh Sash (42mm x 57mm) sliding interlock (one vertical lenght in each shutters) (45.5mm x 28mm), Glazing bead (24.5mmx 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 + - 0.2mm thick galvanised steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware (Touch Lock of zinc alloyed (white powder coated ), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Note: the unit rate quoted by the contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose. |
| 65 | S&F coloured tinted glass 4.0 mm thick ordinary quality fixed with aluminium/PVC/wooden beads in squares/rectangular shape as fit in existing shutters/frame work of area exc 0.5 sqm but n.exc 2 sqm complete all as specified and directed. |
| 66 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia or wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified and directed |
| 67 | Refixingceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets including taking down thesame complete all as specified and directed. |
| 68 | S&F for 4mm thickfigured glass ordinary quality and glazing in frame in square butnexc 0.5 sqm in each pane , complete all as specified and directed. |
| 69 | M&L for complete removal of existing treatment on walls and applying two coatsof distemper oil emulsion over one coat ofprimer with 3mm thick wall care putty on wallcomplete all as specified and directed. |
| 70 | Complete removal of existing treatment on walls and M&L for applying Two or more coatsof 100% Premium acrylic emulsion painthaving VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces with one coat of birla putty complete all as specified and directed. |
| 71 | Taking down cement plaster on brick or concrete wall etc including racking out joint hacking for key, scrubbing down with water etc. complete all as specified and as directed. |
| 72 | M&L forrendering 15 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 73 | M&L forrendering 10 mm thick in CM 1:4 on brick/concrete wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement all as specified and directed. |
| 74 | M&L forrendering 5mm thick cement plaster 1:3 on fair faces of brick work or concrete surfaces of ceilings finished even & smooth(without using extra cement) all as specified and directed. |
| 75 | M&L fir preparation of newplastered surfaces of wall and applying two coatsof distemper oil emulsionover a coat of primer with 3mm thick wall care putty on wallcomplete all as specified and directed. |
| 76 | M & L for preparation of newly plastered surfaces of walls and applying two coats of exterior emulsion paint (weather coat) over a coat of alkali resistance primercomplete all as specified and directed. |
| 77 | M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed |
| 78 | M&L for Partition walls with panels of 1.44 sqm (appx.) made out of aluminum powder coatedhollow sections 63.50x38.10x1.95mm thick ,snap fit beading ,rubber gasket ,5mm thick sheet glass and 12mm thick prelaminated particle board interior grade ,prelaminated one side with decorative chioce lamination and other side balancing light grey lamination including dismantling the damaged partition complete all as specified and directed. |
