}

Repairing Of 2 Nos Of Tube Wells At Barat Ghar And 6 13 Lt Bps Narela Ac 01, Delhi-Delhi

Delhi Jal Board-DJB has published Repairing Of 2 Nos Of Tube Wells At Barat Ghar And 6 13 Lt Bps Narela Ac 01. Submission Date for this Tender is 13-05-2024. Tube Well Tenders in Delhi Delhi. Bidders can get complete Tender details and download the document.




Tender Notice

43320920
Repairing Of 2 Nos Of Tube Wells At Barat Ghar And 6 13 Lt Bps Narela Ac 01
Open Tender
Indian
Delhi
Delhi
13-05-2024

Tender Details

Repairing Of 2 Nos Of Tube Wells At Barat Ghar And 6 13 Lt Bps Narela Ac 01

Key Value

Document Fees
INR 500 /-
EMD
INR 8000.0 /-
Tender Value
Refer document

BOQ Items

Name of Work:Repairing of 2 nos. of Tube wells at Barat Ghar and 6/13 LT BPS, Narela AC 01.
Sl. No. Item Description
1Lifting of p/set by the help of chain pully, clamps and heavy menpower after cuting rusted/wornout and opening of nut bolts to dismental the p/set, pipes etc. This job also i/c the work of installtion of chain pully at upper gadder .
2S/o submersible cable with copper conductor having three core sizes 6 sq. mm working on 1100V. Make:-Finolex/Plaza/Unistar or any other make approved by DJB.
3Making and supply of MS clamp of 500 mm long x 75 width x12 mm thick complete with nut and bolts and washers for holding the 50 mm dia pipe including bending and shaping etc. as required.
4S/o G.I bend 50 mm dia 90deg. Double flange. Heavy class Make: - Ganesh/ ISI
5S/o of 3 mtr. GI pipe 50 mm dia size ,medium class with GI flange welded in both sides 3 Mtr long with ms strips complete with threading work on each side of pipe each flange should be 4 holes and cut for cables. Make :- Jindal / TATA.
6S/o G.I required off size threaded heavy duty nut-bolts of good quality.
7Supply of MS bore cover 4 mm thick suitable for bore size in 2 pieces complete with bolting arrangement angle iron frame and provision of 50 mm diahole in the center.
8S/o pressure gauge of 100 mm dia, 0-30 PSI complete with socket, bush Make:-H-Guru/Fiebig
9Making water sample point with the help of socket, niple, cook valve, Tee and extended pipe etc. of size 1/2 inch.
10Making and Supply of G.I tail piece of 50 mm dia. , one mtr. Long size made out of medium class pipe complete with one end threaded and other end fitted with G.I. flange heavy and cut for submersible cable. Mak of Pipe - Jindal/Tata.
11Supply of Starter panel board suitable upto 12.5 HP Submersible Pump Set for tube wells having following specifications :- 1. Three phase, Star Delta Motor Control Panel, 415 VAC 50 HZ. 2. Digital controlling of parameters i.e Ampere and voltage. 3. PMC Based DC operated 32 Amp. power contractors/micro controller protection unit. 4. Digital Display for Parameters i.e Ampere and voltage & Motor Run Hour. 5. Automatically over load cut off. 6. Under voltage/over voltage automatically cut off. 7. Single phase and reverse phase protection. 8. Auto/manual mode selector switch. 9. MCB- 32 AMP at incomer to interrupt the supply in faulty condition. 10. Programmable Timer, 220 volt AC for auto start and stop. 11. Run hour meter to show the total time of run. 12. IP 56 Protection. Make - Any approved make/ ISI
12Supply ofneoprene rubber sheet having 50% neoprene, 3 mm thick. Make - Jyoti/Worth/DJB approved.
13Supply of electric insulated sheet for AC & DC which is moisture proof, U.V. protected, fire retardant, high di-electric strength, easy to clean, auto glow path, coloured strips on both sides, glow in emergency, CPRI approved, confirming to BISDOC No. ET-02 (5440). Dt: 30-04-04, meeting requirement of IS:3043, IS:5216 (Part 1,2 & 3), IS: 8437 and IEC: 479 PUB-1 tested for breakdown strength tensile, elongation aging properties, insulation resistance effect of acid, alkaline, diesel and transformer oil, leakage current test etc. 1 no. = 1mtr. breadth x 2 mtr. length. Thickness - 3 mm.Make: Electromat/Safevolt
14Installation of all E&M Equipments, lowering pump set into the bore all piping work fixing of valves and accessories executing minor civil works, making electrical connections with cable as required size by the help of chain pulley to lower pump sets testing and commissioning of all E&M equipments at no load and full load conditions as per standard from full satisfaction of Engineer-in-Charge.The job also includes the transportation charges, providing/fixing of required gap piece, for fixing valves, pressure gauge with the help of welding machine etc. Note - The repaired/working submersible p/sets- 2nos shall be provided by the departmentally.
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail