|
| 1 | SCHEDULE ‘A’ SECTION-I |
| 2 | Excavation over area not exc 1.50m deep and getting out in soft/loose soil complete all as specified and as directed. |
| 3 | Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 4 | Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed. |
| 5 | Removing excavated soil/material to a distance exc 250 metre but not exc 500 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed. |
| 6 | Supplyand planting of Hedge and Shrubbery (Mehandi, Tikkam & Sehjan and the like) as directed by Engineer-in-Charge including creation of Beds by excavating 60 cm deep and 60 cm wide trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio 8:1 (8 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludge or manure after reduction by 8%) flooding with water filling with earth if necessary, watering and finally fine dressing leveling etc including stacking and disposal of material declaredunserviceable and surplus earth by spreading and leveling as directed within a lead of 50 m and lift up to 1.50 m complete all as specified and as directed. |
| 7 | Supplyand planting of Bougnvillea Hedge as directed by Engineer-in-Charge including creation of Beds by excavating 60 cm deep and 60 cm wide trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio 8:1 (8 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludge or manure after reduction by 8%) flooding with water filling with earth if necessary, watering and finally fine dressing leveling etc including stacking and disposal of material declaredunserviceable and surplus earth by spreading and leveling as directed within a lead of 50 m and lift up to 1.50 m complete all as specified and as directed. |
| 8 | M&L for preparation of ground and plantation of grassing with “Doob” grass (mandouri) including enough watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth as required including supplying and spreading of Neem oil cakes, manure or sludge and chemical required for preparation of the ground for plantation of grass by uprooting vegetation etc, removing boulders, pebbles and leveling the surface flat or in slope complete all as specified and as directed.Note : The payment against this item will not be allowed immediately after plantation of grass. The payment against this item will only allowed after 60 days from date of plantation when the grass forms a thick lawn free from weeds. |
| 9 | Supply and Planting of following plants in poly bags of 0.25m to 0.30m with minimum height 1.2m to 1.50m including digging holes 0.90m dia x 0.90m deep in ordinary soil and refilling the same with the excavated earth mixed with manure of approved quality or sludge in the ratio 2:1 (2 parts of stacked volume of earth after reduction of 20% with 1 part of stacked volume of sludge or manure of approved quality after reduction by 8%), flooding with water and removal of surplus soil, with & including using suitable chemicals or pesticides of approved quality, as required and making ‘Thaola’ complete all as specified and as directed :-Notes :- (i)The contractor’s quoted rates shall be deemed to include for necessary excavation and earth work, necessary manure or sludge and antitermite treatment of soil including necessary chemicals etc.(ii) The excavated earth if found suitable and approved by GE shall be used for filling in the holes after planting of trees/plants.However, in case the excavated earth is not found suitable for refilling and not approved by GE, contractor shall arrange suitable good earth from his own sources as approved by GE and contractor\"s quoted rates shall be deemed to include for arranging and transporting of good earth including filling in the holes and nothing extra shall be admissible on this account. |
| 10 | Neem Plants |
| 11 | Gulmohar Plants |
| 12 | Peepal Plants |
| 13 | Sheesham Plants |
| 14 | Anar Plants |
| 15 | Amla Plants |
| 16 | Beri Plants |
| 17 | Bakul Plants |
| 18 | Bottle Palm Plants |
| 19 | Plumeria Plants |
| 20 | Fox Tail Plam Plants |
| 21 | Supply, install, testing and commissioning of horizontal open well submersible pump electric driven motor 3 HP, 2.25 KW capacity, with supply voltage 415 Volt, 3 Phase, 50 Hz suitable for operation with operating head 10.5-30 Mtr and having capacity to discharge water 830-360 LPM with suction and discharge flanged suction 65x65mm includingsuitable size of strainer mounted withMS bolts, nuts of required size and necessary control valves, properly connected with suction and delivery water lineincluding Submercible three core copper conductor cable from panel to motor as per suitable size including all connected accessories complete all as specified and directed. (Make : CG /Kirloskar/MBH Pumps/KSB/Mather & Platt or eaquivalent). |
| 22 | Supply, install, testing and commissioning of mono block pump set 1 HP, capacity, with supply voltage 415 Volt, 3 Phase, 50 Hz with 3000 RPM in stainless steel body with inlet filter driven by suitable for operation with operating head 28-14 Mtr and having capacity to discharge water 1.9-0.4 LPS with suction and discharge flanged suction 40x40mm includingsuitable size of strainer mounted on suitable for existing surface with MS bolts, nuts of required size and necessary control valves, properly connected with suction and delivery water line including three core copper conductor cable from starter panel to motor as per suitable size including all connected accessories complete all as specified and directed. (Make : CG /Kirloskar/MBH Pumps/KSB/Mather & Platt or eaquivalent). |
| 23 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified and directed.Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 24 | Supply, laying, jointing and testing LT XLPE insulated screened,bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified and directed.Notes :- (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions. |
| 25 | Supply, laying, jointing and testing single core cable multi stranded copper conductor PVC insulated and sheathed copper cable 1100 Volt grade6 sqmm single core including all connection arrangement complete all as specified and directed.Note : Cable connection from star delta starter control panel to motor terminals. |
| 26 | M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed. |
| 27 | M&L for dry sand (Local Tibba sand) and punning for cushioning and cover for protection of under ground electric cable complete all as specified and as directed.Notes :- (i)Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used.(ii) For the purpose of payment, only punned thickness shall be measured. |
| 28 | M&L for Boring of holes under main road, pavement, hard standing, (minimum 1.0m below) etc by trenchless technology using ultra sound technique and necessary machine for accomodate upto 100mm bore GI tube, light grade in the drilled holes, suitable for passing the GI protection pipe / cables, including returning, filling in the end working space including removal of surplus soil and making good the surface complete all as specified and as directed. Note : Actual length of road/ pavement / hard standing will be measured for payment purpose, no extra payment will be admissible for side excavation. |
| 29 | M&L for Cutting/dismantling of PCC hardstanding/ WBM road with soling & premix carpet of any description for laying of cable and disposal of material to a distance not exc 250m and making good the same with & including black top of surface dressing renewal coat by spraying evenly paving bitumen at 12 Kg per 10 sqm chipping @ 0.10 cum per 10 sqm and rolling to required gradient and camber complete all as specified & as directed. |
| 30 | M&L for Galvanized iron tubing, 50mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (25mmx3mm) clamps, bolts, nuts and washers for protection of LT electric cable complete all as specified & as directed. |
| 31 | M&L for Galvanized iron tubing, 50mm bore medium grade, ISI marked, including all fittings and fixed to wall and ceiling or laid in floor including necessary fittings for suction pipe of monoblock pump complete all as specified & as directed. |
| 32 | M&L for Galvanized iron tubing, 40mm bore medium grade, ISI marked, including all fittings and laid in trenches/ under floor/ under road or laid in floor including necessary fittings complete all as specified & as directed. |
| 33 | M&L for Galvanized iron tubing, 20mm bore medium grade, ISI marked, including all fittings and laid in trenches/ under floor/ under road or fixed to wallm ceiling/above trenches including necessary fittings complete all as specified & as directed. |
| 34 | M&L for Earthing to LT Panels with & including galvanised mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 25x4 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to transformer / GOD / Panel / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed.Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. |
| 35 | Supply, installing, commissioning and testing LT panel board (outdoor type) cubical type made out of CRCA sheet 3.15mm thick dust and vermin proof and angle iron of size 40x40x5mm, pedestal frame grouted in PCC (1:2:4) type B-1 20mm graded crushed stone aggregated thimble and cable entry boxes with cable glands. Panel should covered from all sides with front and back lockable door and hinges complete with aluminum bush bar of capacity 63 Amps, TPN, Three phase, 04 wire (in separate chamber) including painting with two coats synthetic enameled paint over a coat of red oxide primer and consisting of the following:-(a) MCCB, 4 Pole, 25 Amps, rupturing capacity 16 KA, 415 Volt grade, AC, 50 Hz, Thermal Magnetic type - 01 No. (Incoming).(b)MCB 16 Amp rating, 3 Pole, rupturing capacity 10 kA, ‘C’ Series - 02 No (Outgoing)(c) Digital Volt meter 0-500 Volt with built in 3 way selector switch - 1 No.(d) Digital Amp meter 0-50 Amp with built in 3 way selector switch including CTs - 2 Nos.(e)Neon Indicator lamps Set RYB, “LED” type (set of three) - 01 Set(f) Single phase preventer suitable for 3 HP submersible pump set - 02 Mos(g) DOL Starter in sheet steel enclosure, suitable for 3 HPelectric Motor, current rating 12 Amp 3 phase, 415 volt, 50 Hz, with over Load Relay range 2.5A to 4 Amp - 02 Nos |
| 36 | Supply and fixing star delta starter control Panel 1.0 HP on wall with all fitting arrangement & comprising of the following accessories complete all as specified and directed :-(a) Star delta Starter motor starter in sheet steel enclosure, suitable for 1 HPelectric Motor, 3 Phase, 415 volt, 50 Hz - 01 Nos(b)MCB 16 Amp rating, TPN, ‘C’ Series - 01 No(c) Digital Volt meter 0-500 Volt with selector switch - 1 No.(d) Digital Amp meter 0-50 Amp with selector switch - 1 No.(e)Neon Indicator lamps Set RYB, “LED” type (set of three) - 01 Set(f) Single phase preventer suitable for 1 HP submersible pump set - 01 Mos |
| 37 | Supply and fixing 5000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed. |
| 38 | S&F MCB, 25 Amps, Four Pole, 415 Volts grade, 10 kA, ‘C’ Curve, with over load and short circuit protection, in existing panel complete all as specified and as directed. |
| 39 | M&L for Valve Pit of internal size 750mm x 750mm x 750mm built in brick masonry complete all as specified in Particular Specifications and as shown on drawing No. BTD-811 Sheet No. 1/2 & 2/2. |
| 40 | S&F 50mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. |
| 41 | S&F 40mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. |
| 42 | S&F 20mm bore Gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete, all as specified & directed. |
| 43 | Supply and fixing portable impact sprinkler (brass) system ISI marked on MS tripod base as per sketch with 20mm dia inlet full, 360 degree coverage and adjustable deflactor flap to adjust throw distance upto 80 feet and height adjsutable complete all as specified and directed. |
| 44 | Supply and fixing PVC flexible pipe 20mm dia for connecting sprinkler system to GI water posts complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 45 | Supply and fixing PVC pipe (6 kg/cm²) IS ; 4985 : 2000 CML No 8652891 size of 75mm dia for sub distribution line in drip irrigation system and including all connected accessories (i.e socket, bend, Elbow, Tee, Reducer, connector, Solvent, etc) complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 46 | Supply and fixing PVC pipe (6 kg/cm²) IS ; 4985 : 2000 size of 63mm dia for sub distribution line in drip irrigation system and including all connected accessories (i.e socket, bend, Elbow, Tee, Reducer, connector, Solvent, etc) complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 47 | Supply and fixing Plain lateral 2.5 kg/cm², Class-II size of 32mm dia, for water distribution line in drip irrigation system andincluding all connected accessories (i.e socket, bend, Elbow, Tee, Reducer, connector, suitable size Grommat Joiner 16mm take off, End cap, etc) complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 48 | Supply and fixing Plain lateral 2.5 kg/cm², Class-II size of 16mm dia for line for water distribution line in drip irrigation system including all connected accessories (i.e Grommat, Lateral cock, End cap for connection in UPVC/ Plain lateral pipe etc) (for trees) complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 49 | Supply and fixing Emitting pipe of dia 16mm, discharge 2 LPH, dripper spacing 30cm. 2.5 Kg/cm², IS:13488, including all connected accessories (i.e socket, bend, Elbow, Tee, connector, suitable size Grommat, Joiner etc for hedge) complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 50 | Supply and fixing Control valve size of 75mm dia for head control unit sub distribution line in drip irrigation system and all connected accessories complete all as specified and directed Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 51 | Supply and fixing Control valve size of 63mm dia for head control unit sub distribution line in drip irrigation system and all connected accessories complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 52 | Supply and fixing Flush valve size of 75x63mm dia for sub distribution line in drip irrigation system complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 53 | Supply and fixing service saddle of 63x32mm dia for water distribution line in drip irrigation system complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 54 | Supply and fixing push type male/ female threaded adopter size of 32mm dia for water distribution line in drip irrigation system complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 55 | Supply and fixing PP control valve (Th. End) size of 32mm dia for sub distribution line in drip irrigation system complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 56 | Supply and fixing Dripper cap 8 LPHfor drip irrigation system and connected accessories complete all as specified and directed. Make : Finolex/ Supreme/ Prince/ Kisan/Tirupati |
| 57 | Supply and fixing Pop-Up Impact sprinkler of heavy duty Plastic, adjustable to full-circle or Part circle with diffuser screw for fine drop lets and throw control, inlet size 3/4\", having radious of throw up to 12 mtrs at pressure 4 Kg/cm² omplete all as specified and directed. Make Aquaturf. |
| 58 | Supply and fixing Swing joint full three way adjustability including neight for Pop-Up Impact Sprinkler, bush with connected accessories, durable polyethylene construction for 3/4\" size. Complete all as specified and directed.Make Aquaturf |
| 59 | Supply and fixing PP Service saddle size 63mmx20mm for jointing of swing joint to PVC Pipe for Pop-up Sprinkler complete all as specified and directed. |
| 60 | Supply and fixing PVC End cap size of 63mm dia for water distribution line in Pop-Up irrigation system and all including complete accessories all as specified and directed. |
| 61 | Supply and fixing Robust top cover with non slippery grip Plastic heavy duty extended bottom keeps the valve box stable and firmly set in the soil with Green Topand black base size 10\" rectangular shape at Pop-up distribution line and including all connected accessories complete all as specified and directed. |
| 62 | Supply and fixing Hydrocyclone filter with 2 solid flange size of75mm dia and capacity of 30 m³/hour for head control unit in drip irrigation system IS 14743:1999 with all connected accessories complete all as specified and directed. Make : Sourabh shaktiman |
| 63 | Supply and fixing PP manifold of size 75mm for Filter Unit of Drip and Pop-up system with connected accessories complete all complete as specified and directed. |
| 64 | Supply, fixing Ventury with Ferttigation Manifold assemble size of 63mm for head control unit IS : 14483:1997 with all acessories complete all as specified and directed. Make : Saurabh Shaktiman |
| 65 | Supply and fixing Air relese valve (plastic) size of 25mm dia for head control unit in drip irrigation system complete all as specified and directed. |
| 66 | Supply and fixing Pressure gauge (glycerine) capacity of 0-7 kg/cm² size of 63mm dia for head control unit in drip irrigation system complete all as specified and directed. |
| 67 | Supply and fixing Screen filter (plastic) with 2 solid flange size of 75mm dia and capacity of 30 m³/hr for head control unit in drip irrigation system IS : 12785:1994 complete all as specified and directed.Make : Saurabh Shaktiman |
| 68 | Supply and fixing PP control valve size of 75mm for controlling water in storage tank for drip irrigation system complete all as specified and directed. |
| 69 | M&L for cutting of existing DI pipe line for making branch connection by inserting DI Tee of size 100x100x50mm dia complete all as specified and directed. Note : (i) Rate for fixing of DI fittings (ISI marked) upto 100mm bore included in the quoted rated of this item.(ii) Earth work fo the same will be measured and paid seperately under relevent item of this Schedule. |
| 70 | S&F tree guard of size 450mm dia x 1.50m height (excluding leg height) made of welded wire mesh of 2.10mm dia with mesh size 50mmx50mm. The welded wire mesh shall be strengthen with 03 Nos circular band made of FI 20x3mm. The leg of tree guard shall be 450mm high made of angle iron of size 25mmx25mmx4mm (03 Nos). The quoted rate deemed to be included painting of the tree guard with two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 71 | S&F tree guard of size 600mm dia x 1.50m height (excluding leg height) made of welded wire mesh of 2.10mm dia with mesh size 50mmx50mm. The welded wire mesh shall be strengthen with 03 Nos circular band made of FI 20x3mm. The leg of tree guard shall be 450mm high made of angle iron of size 25mmx25mmx4mm (03 Nos). The quoted rate deemed to be included painting of the tree guard with two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 72 | SCHEDULE ‘A’ SECTION-II |
| 73 | M&L for maintenance of all Plants, Hedge, shrubbery, Grass, etc provided under Sch \"A Sec-I by weeding, hosing, saucer making once in every month (minimum) for plants /hedge, once in every 15 days for carpet grass/country grass/doob grass, Barmuda grass pruning dried barnches, insect and pest management (as and when required), pruning dried branches once in every week (minimum), depositing the material at place as directed by Engineer-in-Charge and planting the new plants in place of dead plants of same species and height turning without any extra cost to the department including watering of Plants, Hedge grass using own arrangements, complete all as specified and as directed.Note : Contractor shall be responsible for all necessary arrangements for collection and conveyance of water from MES water supply points/source located upto 10 KM from the site for watering of Plants, Hedge, Shrubbery and Grass. Necessary water tanker with tractor, water browser, PVC pipes, etc required for watering purpose shall be contractor’s responsibility and quoted rates of this item shall deemed to include this provision. Manure & pesticide required for maintenance of plant under this item shall be arranged by the contractor at his own cost and cost of the same shall be deemed to included in the rate quoted against this item. |
