Nuclear Fuel Complex has published Tender For Civil, Ph And Electrical Works For Renovation Of Type I Quarters Phase-Iv At Hwpk Housing Colony, Kota Rawatbhata, Rajasthan.. Submission Date for this Tender is 15-05-2024. Electrical Maintenance Tenders in kota Rajasthan. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Felling down carefully trees of girth (measured at a height of 1.0m above ground level) including necessary excavation, removal / destruction of roots, filling the excavated pockets thus formed with good earth, compacting the same, cutting the trunks and branches of trees into suitable pieces, transporting, stacking and disposing the same at the location as directed by Engineer – in – Charge. |
| 2 | Beyond 30 cm girth upto and including 60 cm girth |
| 3 | Beyond 60 cm girth upto and including 120 cm girth |
| 4 | Earth work excavation in overareas/foundations in all soils and ordinary rock up to 1.5m depth including dressing of sides and ramming of bottoms, lifting including getting out the excavated soil , backfilling with useful materialnot exceeding 20cm in depth and disposal of surplus excavated soils as directed, withina distance of 2.0 KM etc., complete. |
| 5 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees andsaplingsof girthupto30cmmeasuredataheightof1maboveground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 6 | Plain Cement Concrete 1:3:6 using Portland PozzolanaCement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Ambuja , make) with crushed sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc.,but excluding Formwork, complete as specified and directed. |
| 7 | Reinforced Cement Concrete by insitu mixing using Weigh Batching or RMC of Ultra Tech, Birla Ready Mix of Grade M - 25 (Minimum Cementitious Content not less than 330 Kg/Cum) up to specified level using Portland PozzolanaCement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Ambujamake) with crushed sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer of brand M/s. Fosroc, Demech, Huntsman, Pidilite, Sunanda Chemicals, Agro Chemicals, MBT in proportion as per Manufacturer"s Specifications, Pumping / Lifting of concrete to the required heights, Concrete laid to properlevel, profile and slope, placing concrete, consolidation, finishing,curing, etc.,but excluding Formwork as specified and directed. |
| 8 | Brick work using quality flyash (nonmodular) bricks of class designation 7.5conforming to IS12894 using cement mortar 1:6 using crushed sand of grade conforming to BIS 2116at and at all depths below plinth level in foundation and in plinth, storm water drains, etc., simultaneous pointing with same mortar below ground level, and ranking out joints above ground level, curing etc.,complete as per specifications and as directed forsub structure etc., |
| 9 | Brick work using quality flyash bricks of class designation 7.5 conforming to IS12894 using cement mortar 1:6 using crushed sand of grade conforming to BIS 2116 at all depths and heights above plinth level including pilasters, steel / tubular scaffolding, rakingout joints, curing etc., complete as per specifications and as directed in super structure. |
| 10 | Half brick masonry using non modular fly ash bricks of class designation 10, conforming to IS :12894 in partition walls in cement mortar 1:4 using crushed sand of grade conforming to BIS 2116at all depths and heights below and above plinth level including scaffolding, raking out joints, curing, etc., complete including providing stiffeners of reinforced cement concrete 1:2:4, 115 mm x 75 mm size at every 900 mm height, necessary formwork, curing, etc., complete as per specifications and as directed but excluding reinforcement. Note:- Reinforcement will be paid under relevant item. |
| 11 | Cement plastering 6 mm thick for ceiling with cement mortar 1:3 finished smooth finish, including hacking of concrete surfaces, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed. |
| 12 | Cement plastering 15 mm thick for internal walls in cement mortar 1:4 finished smooth and at all heights above plinth level over brick walls or concrete surfaces including making necessary grooves in between junctions of brick masonry and RCC and also other places wherever required over brick walls or concrete surface, preparation of surface, steel/tubular scaffolding, curing, etc., complete as directed. |
| 13 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 14 | PaintingwithTwoormorecoatsof synthetic enamelpaint using1stquality synthetic enamel paint of Asian Paints, Berger, Nerolac, Shalimar or equivalent of approvedbrandandmanufacture onwood/steel surfaces of requiredcolour andshade,includingapplyingadditionalcoatswhereverrequiredtoachieve evenshadeandcolour,includingpreparingsurfaces,scaffolding,fillingwith putty wherever required & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge : |
| 15 | Painting (one or more coats) onoldrain water, soil, waste and ventpipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture |
| 16 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge including SS butt hinges and screws |
| 17 | 35 mm thick for Main door with 4 Nos. SS Butt Hinges of size 125x64x1.90 mm confirming to IS: 12817 |
| 18 | 30 mm thick for Main door with 4 Nos. SS Butt Hinges of size 100x58x1.90 mm confirming to IS: 12817 |
| 19 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board 18 mm thick one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge.includingstainless steel piano hinges (size 1mm thick 35mm wide bright finished stainless steel)/soft close clip on concealed hinges complete. |
| 20 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. |
| 21 | 100mm length for cupboard |
| 22 | 125mm length for doors |
| 23 | Providing wood work with CP teakwood in frames for cupboards using II class teakwood at all heights above plinth level wrought framed and fixed in position including providing and fixing with suitable size of coach screws wherever required / M.S. hold fasts of size 40 mm x 3 mm and 200 mm long, bent to shape embedded in cement concrete 1:2:4 blocks for door frames, fixed in position with necessary lugs rawl plugs and screws and coach screws, applying two coat of approved wood primer to the exposed surfaces of door frame and two coats of bituminous paint to the surfaces of frames in contact with masonry/concrete, etc. sealing the gaps if created with silicon sealent, complete as indicated in drawings and as directed. |
| 24 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced withgalvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware,SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleevefor fixing frame to finished wall as perIS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 25 | Casement cum fixed panel window having one single casement panel & one fixed panel with S.S 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. Using R4 series with frame (64mm & above) x (50mm& above) & sash (64mm & above) x (70mm & above) & mullion (64mm & above) x (70mm & above). (Height above 1.8 metre; each openable shutter upto 0.8m width) |
| 26 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias, stairs and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 27 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 28 | Providingandfixingflyproofstainlesssteelgrade304wiregauge,to windowsandclerestorywindowsusingwiregaugewithaveragewidthof aperture1.4mm inbothdirectionswithwireof dia.0.50mm withmatching wood beading in wooden doors, windows and clerestory windows and with nut- bolt/screw/wooden/metalbeadingasperexistingarrangementinsteel doors, windowsandventilatorsincludingremovingtheexistingmeshifany,all complete as per the specification and as directed by EIC. Note: Clear opening area ofpanel inserts (excluding portion inside grooves or rebates) shall only measured for payment. 2.Nut-bolts,screw,beadingrequiredforaboveworkaretobearrangedby contractor at his cost and nothig extra is paid on this account. |
| 29 | Removing of existing glass panes and supplyinh and fixing new glass panes of 4mm float glass in the clerestory windows,including providing necessary screws and washer for fixing the beading again to the window shash, all as directed by EIC |
| 30 | Removing of existing window panes and supplying and fixing new window panes of 3mm ACP sheet in the clerestory windows, including providing necessary screws and washer for fixing the beading again to the window shash, all as directed by EIC |
| 31 | Maintenance of steel windows and mosquito shutter, like oiling of hinges, adjusting the shash and rall of windows to fit in the steel casements, including welding, grinding if required for proper fiting of window in casement. |
| 32 | Removing of old doors and stacking the doors at place near the site location as directed by EIC. |
| 33 | Providing and fixing in position following items including all necessary fixtures, fittings, finishing etc. all complete. |
| 34 | Approved make pressure die cast zinc alloy, chromium plated door handle. 150mm long |
| 35 | Approved quality satin steel aldrop 250mm long, 14mm dia. |
| 36 | Approved quality Stainless steel 304 tower bolts conforming to IS-204, 250 x 10mm. |
| 37 | Approved quality Stainless steel 304tower bolts conforming to IS-204, 150 x 10mm. |
| 38 | Approved quality Godrej Inside Opening 7 Lever Night Latch or equivalent. |
| 39 | Cutting the stile of the steel frame mosquito net door shutter, making the door height short to match the new floor level, welding the bottom rail again to stile of existing door shutter and finishing smooth. |
| 40 | Providing and laying at all floors and levels 6mm (min) thick first quality glossy/ matt / antiskid/rustic / digital collection etc. ceramic tile flooringas per the approved pattern and colour as mentioned below conformingto IS 15622 latest of edition from approved list of maufacturers or equilvalent laid in cement mortar bedding / backing, close jointed and grouted with matching cement slurry to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings/cutout if necessary, wastage and final cleaning of surfaces as required, curing etc.complete all as per drawing specifications & as directed by Engineer in charge. a) In flooring with rustic/matt finished/ 300x300mm, 600 x 600mm or equivalent approved sizes of ceramic tile laid over 20mm thick cement mortar bedding 1:4 ( 1 cement : 4 sand) b) In skirting laid over 12 mm thick CM 1:3 backing. c) Anti skid ceramic tile with 300x300 or equivalent approved sizes of ceramic tile laid over 20/15mm thick cement mortar bedding 1:4.In dado / clading with tile of size 200x300mm or size as per working drawing laid over 12 mm thick CM 1:3 backing for toilets. d) Sand shall be crushed stone sand. e) Tiles shall be of make Kajaria/Regency/Somani/Jhonson & Jhonson Note:i) Quoted rate shall include extra cement mortar required to match the water proofing plaster if any to maintain the lines and plumb of dado. ii) The quoted rate shall include border / combination of tiles as instructed by the Engineer in Charge iii)The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly. |
| 41 | Anti skid ceramic tile with rectified 300x300 or equivalent approved sizes of ceramic tile laid over 20/15mm thick cement mortar bedding 1:4. for toilets |
| 42 | In dado / clading with tile of size rectified 300 X400 mm or size as per working drawing laid over 12 mm thick CM 1:3 backing for toilets. |
| 43 | Providing and laying double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make like Kajaria/Regency/Somani/Jhonson & Jhonson , in all colours and shades, laidcement mortar , jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., completefor entrance foyer, corridors, lobbies, etc. Note: i) Quoted rate shall include extra cement mortar required to match the water proofing plaster if any to maintain the lines and plumb of dado. ii) The quoted rate shall include border / combination of tiles as instructed by the Engineer in Charge iii)The sizes of tiles mentioned are approximate and subject to the availability in market during execution. If the required size is not available the next higher size of tiles shall be used without any extra cost to the Department. The tenderer may note the same and quote accordingly. |
| 44 | In flooring/skirting with rustic/matt finished/ 600X600 mm or equivalent approved sizes of double charged vitrified tile of make Somany/Kajari or approved equivalent laid over 20mm/12mm thick cement mortar bedding 1:4 ( 1 cement : 4 sand) |
| 45 | "Providing & laying homogenous Parking tiles of Kajaria/HR Johnson/Somani/Pavit or any other approved equivalent in footpaths approaches and other location, in approved pattern as shown in drawing and laid over 20mm cement mortar (1 : 4) bedding including cleaning and preparing the surface for bedding, and fixing the tiles over the repaired bedding mortar, finished to level, line, slope andplumb, cutting of tiles, wastage, making openings /cut out if neccesary, final cleaning of surfaces, curing, at all locations, levels and lead etc., complete all as per drawings,specifications & as directed by Engineer inCharge. i) InFlooring with 400x400mm (thickness as per manufacturer"s specifications) size tile laid over 20mm thick cement mortar bedding 1:4 ( 1 cement : 4 coarse sand) |
| 46 | Providing and fixing EUROPEAN WATER CLOSET suite comprising Hind ware or jaguar : a) WASH DOWN PATTERN European water closet best Indian make, in light colour glazed vitreous, with integral ‘P’ or ‘S’ trap. b) Plastic low level flushing cistern of gleaming light colour shade, best quality, champion or approved equivalent, conforming to IS:7231 complete with all internal fittings, matching heavy quality PVC flush bend mounted on a pair of white enamel painted brackets. c) 15 mm n.b. heavy quality PVC inlet of heavy quality connection with CP brass unions connected at ends. d) 15 mm n.b. screw down variety heavy quality C.P. brass stop cock conforming to IS:781. e) Solid plastic heavy quality seat with lid of approved make and colour with C.P. brass pillar hinges, conforming to IS:2548 (Part I&II). f) 15 mm n.b. heavy quality GI overflow pipe with specials from cistern to 150 mm above floor level painted and terminated with mosquito-proof perforated cap. |
| 47 | Providing and fixing wash basinsize 630X450mm ofM/s. Hindware/jaguar or approved equivalentofwith C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, 15 mm n.b. screw down heavy quality C.P. bras stopcock conforming to IS: 781., 32 mm CP brass bottle trap, with extension pieceincluding painting of fittings and brackets, cutting and making good the walls wherever required complete as specified and directed |
| 48 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threadedfittings,i/cfixingthepipewithclampsat1.00mspacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the costofcuttingchasesandmakinggoodthesameincludingtestingofjoints complete as per direction of Engineer in Charge |
| 49 | a) 20 mm nominal outer dia Pipes |
| 50 | b) 32 mm nominal outer dia Pipes |
| 51 | ProvidingandfixingPVCwatertankofsyntexoranyapprovedmakeof capacity500Litresincludingallnecessaryfittings,labouretc.asdirectedby EIC |
| 52 | Providing & fixing 110mmdiaO.D.Size.embeddedPVCrainwaterpipejointedwithbonding solution of approved quality and make confirming to IS 13952 including clamps, connections etc. all as per approved manufacturer"s details |
| 53 | Providing and fixing heavy quality fancy variety C.P. brass screw down BIB TAPS/Push Tap/Two Way Bib Tap of M/S. Jaguar/Hindware make conforming to IS: 8931 |
| 54 | Providing and fixing heavy quality fancy variety C.P. brass screw down CONCEALED TYPE STOP COCKS of Jaguar/ M/s. Bilmat/GEM/ ESSCO/Metro or approved equivalent make conforming to IS:8931 on G.I. lines of size 15 mm for shower. |
| 55 | CP Brass Angle Cock 15NB of M/S. Jaguar/Hindware |
| 56 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink of M/s Nirali or equivalent without drain board with bowl size 610x510mm bowl depth 200mm as per IS:13983 and 15mm CP brass long neck pillar tap, fixing sink with C.I. brackets and stainless steel plug 40 mm and waste coupler, including painting of fittings and brackets, cutting and making good the walls wherever required, fixing in granitic slab, sealing the edges with silicon sealent. |
| 57 | Providingandfixing600x450mmbevelededgemirrorofsuperiorglass(of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 58 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. |
| 59 | NOTE :- 1)The treatment shall be tested by ponding water for a period of 10 days. If due to location of rain water pipes the average thickness of treatment exceeds 110 mm for easy flow of water the extra brickbat coba will be paid as extra item and the rate for the same to be got approved from the Department before execution 2) The waterproofing treatment is to be guaranteed for bone-dry condition for a period of 10 years in the prescribed proforma. 3) The measurement for payment shall be the entire area of terrace covered by the treatment measured between brick/concrete parapets without plaster and the area of vatas calculated by taking the length of vatas and the height above the finished level of the terrace. |
| 60 | Dismantling of brick work in Cement mortar manually/ mechanically with out damagingadjacentstructureincludingstackingofmaterialsanddisposalof unserviceable materials within 50m lead and as directed by EIC. |
| 61 | Demolishingstonerubblemasonrymanually/bymechanicalmeansincluding stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge |
| 62 | Cleaningofchockedsewerlinebydieselrunningvehiclemountinghydraulic operatedhighpressure suctioncum jetting sewer cleaning machine fitted with pumphaving4000litressuctioncapacityand6000litreswaterjettingtank capacityincludingskilledoperator,supervisingengineeretc.forcleaningand partialdesiltingofmanholesanddechockingofsewerlines.Dechockingand flushingofsewerlinefromonemanholetoanotherbyhighpressurejetting systemof2200PSIforsewerlinefrom150mmdiaupto300mmdiaforall depth |
| 63 | Disconnecting Water Tank & Cleaning of Traps |
| 64 | Disconnectingdamagedoverhead/terracePVCwaterstoragetankofanysize fromwatersupplylineandremovingfromtheterraceincludingshiftingat ground level as per direction of Engineer-in-charge. |
| 65 | Cleaninganddesiltingofgullytrapchamber,includingremovalofrubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer- in-charge |
| 66 | Providing PVC Nahani trap of supreme, prince, kasta or equivalent make with SS jali over it. Outlet 75NB |
| 67 | Providing and laying PVC drainage pipe including jointing, sealing, connecting to existing floor trap 75NB |
| 68 | Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shadewith silicon additives. (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 69 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. not less than Two Coats |
| 70 | ELECTRICAL Supply and installation of Legrand/Hager/ Havells/ MDS/Siemens make double door 12 way SPN Distribution board with minimum IP 43 fitted with following components: a. 32A 30mA DP RCBO -1 No Incomer b. 25A SP MCB - 1 No c. 10A SP MCB - 5 No d. 6A SP MCB - 2 No |
| 71 | Supply |
| 72 | Installation |
| 73 | Supply and installation of following light fittings of Philips/Wipro/Bajaj make with all accessories like supporting hard ware, ceiling roses, downrods etc as required to complete the installation in all respects Industrial LED tube light fitting with lumen out put > 2000 Lumens similarto PhilipsTMC 501 batten with LED tube with required hardware to fix the fitting on wall/ceiling |
| 74 | Supply |
| 75 | Installation |
| 76 | Surface mounted LED circular light fittings with lumen output of 1200 lumen similar to philips SM250C LED12S with required hardware for mounting on ceiling |
| 77 | Supply |
| 78 | Installation |
| 79 | Supply and fixing of 230V,1200mm sweep Energy efficient 5 star rated BLDC ceiling fans with required downrods, ceiling roses etc of CG/ Khaitan/Orient/Bajaj/ Almonard/ Usha/ Marathon make with all required accessories. Warranty: 2 Years |
| 80 | Supply |
| 81 | Installation |
| 82 | Supply and fixing of 300mm sweep Single phase exhaust fan with air delivery > 1100 M3/Hr of CG/ Khaitan/ Orient/ Bajaj/ Almonard/ Usha/ Marathon make with all required supports and accessories |
| 83 | Supply |
| 84 | Installation |
| 85 | Supply and fixing of angle/straight bulb hoider with polycarbonate housing of Anchor/Wipro/Havells make with all required accessories |
| 86 | Supply |
| 87 | Installation |
| 88 | Supply and pulling of following sizes of flexible FR copper wires of Polycab/Finolex / L&T/ Anchor /GEM make to be drawn in 2mm thick PVC conduit/channels with ferruling on both ends excluding cost of pipes, channels and switch boards. |
| 89 | 1.5 Sqmm FR Copper wire |
| 90 | Supply |
| 91 | Installation |
| 92 | 2.5 Sqmm FR Copper wire |
| 93 | Supply |
| 94 | Installation |
| 95 | 4 Sq.mm FR Copper wire |
| 96 | Supply |
| 97 | Installation |
| 98 | Supply and installation of DLP plastic trunking system of Legrand/Hager/Schneider make with required clamps for fixing, cover, end caps etc complete including required angles and junctions of following sizes |
| 99 | 32x20 mm |
| 100 | Supply |
| 101 | Installation |
| 102 | 32x12.5 mm |
| 103 | Supply |
| 104 | Installation |
| 105 | Supply and installation of modular surface mounted PVC switch boards (with PVC box), with face plate, frame of following sizes with latest model rugged modular type sparkproof switches and shuttered sockets of Crabtree/ Northwest/ Legrand/ Schneider Electric |
| 106 | 12 Modular Switch Board with 6 Nos 6A switches, 1 No 6A Socket and 2 Nos Step type fan regulators |
| 107 | Supply |
| 108 | Installation |
| 109 | 3 Modular Switch Board with 1 Nos 16A Universal socket and 1 Nos 16 A switch |
| 110 | Supply |
| 111 | Installation |
| 112 | 6 Modular Switch Board with 2 Nos 10A 5 Pin sockets and 2 Nos of 10 A switches |
| 113 | Supply |
| 114 | Installation |
| 115 | 3 Modular Switch Board with 3 Nos 6A switches |
| 116 | Supply |
| 117 | Installation |
| 118 | 2 Modular Switch Board with 1 No of 16A socket |
| 119 | Supply |
| 120 | Installation |
| 121 | 1 Modular Switch Board with 1 No 16A MCB |
| 122 | Supply |
| 123 | Installation |
| 124 | 1 Modular Switch Board with 1 No Bell push button |
| 125 | Supply |
| 126 | Installation |
| 127 | Supply and installation of Musical calling bell of Havells / GM/ Anchor/ GoldMedal make with required battery |
| 128 | Supply |
| 129 | Installation |
| 130 | Supply and installation of maintenance free earthing stations of ASHLOK/ERICO/JEF make with copper bonded steel ground rod with around 20mm dia and 3 Mts long , Ground Enhancing Material (GEM), inter connecting earth tape between earthing stations and back fill material.Construction of masonary chamber of 450 x 450 mm with CI cover, earth station markers etc complete. Pit should be as per IS 3043 Make: Ashlok, Erico, JEF |
| 131 | Supply and fixing of 25 x 6 mm hot dip galvanised GI strip for earthingby clamping on walls/trays/trench/ground with all required accessories |
| 132 | Supply |
| 133 | Installation |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
