Indian Oil Corporation Limited-IOCL has published Tender For Construction Of Cisf Colony At Nana Kapaya, Mundra. Submission Date for this Tender is 08-05-2024. Road Work Tenders in mundra Gujarat. Bidders can get complete Tender details and download the document.
| FileName | File Description | File Size |
| 627caa1e-ef45-44a4-8ded-4f26592c4f84.html | Tender Notice | 0 KB |
| Annexures.pdf | Tender Document | 0 KB |
| Bidders_help_Document_for_1.pdf | Tender Document | 0 KB |
| BOQ_186756.xls | Tender Document | 0 KB |
| FAQs-IOCL-Online-EMD.pdf | Tender Document | 0 KB |
| Special_Instructions_to_t_2.pdf | Tender Document | 0 KB |
| Techbid.pdf | Tender Document | 0 KB |
| Tender-Acceptance-Format.pdf | Tender Document | 0 KB |
| Tendernotice_1.pdf | Tender Document | 0 KB |
| Sl. No. | Item Description |
| 1 | EXCAVATION :Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. |
| 2 | EARTH FILLING : Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 3 | PCC : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | (a): 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | (b) 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | BBCC |
| 7 | RUBBLE SOLING : Supplying and laying 225mm thick rubble soling including properly packing the stones, filling the interstices with small pieces of stones, stone dust , murrum including ramming, watering , rolling , etc. complete. |
| 8 | CEMENT CONCRETE MIX : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | CEMENT CONCRETE MIX : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | CEMENT CONCRETE MIX : Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 11 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level : Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 12 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works(beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases ,buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc ) above plinth level upto floor V level : Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 13 | REINFORCEMENT : Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth & above plinth level. Thermo-mechanically Treated bars of grade Fe-500D or more |
| 14 | Brick work |
| 15 | 18" Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 16 | 9" Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level inall shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 17 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) |
| 18 | CEMENT PLASTER (IN FINE SAND) |
| 19 | 12 mm cement plaster of mix :1:4 (1 cement : 4 fine sand) |
| 20 | 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement : 4 fine sand) |
| 21 | 20 mm cement plaster of mix :1:4 (1 cement : 4 fine sand) |
| 22 | Waterproof plaster: Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 23 | WATERPROOFING: Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. |
| 24 | STONE / TILE / GRANITE WORK |
| 25 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size : Size of Tile 600 x 600 mm |
| 26 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed vitrified floor tiles polished finish of size : Size of Tile 600 x 1200 mm |
| 27 | Fixing glazed/ Ceramic/ Vitrified tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. |
| 28 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations ofequired size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 29 | KOTA STONE : Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 30 | Glass mosaic: Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge: |
| 31 | Terrace tiles with spacer and epoxy grout Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. |
| 32 | GRANITE DOOR FRAME : Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations ofequired size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 33 | GRANITE WINDOW FRAME : Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations ofequired size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 34 | Granite top : Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations ofequired size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 35 | FABRICATION |
| 36 | M.S. railing : Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 37 | M.S. handrail : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube |
| 38 | Elevation grill |
| 39 | Door frame : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood |
| 40 | Door frame - M.S. |
| 41 | ELECTRIFICATION |
| 42 | Supply, fixing, testing & commissioning of Main LT Panel, 200A MCCB- 1 No. Incomer, 63A FP MCB- 3 Nos. Outgoing, Auxiliary Contact For 63A 4P MCB, Digital Kwh Meter,CL-1 -1 Nos., Three phase Voltmeter 1.0, Three phase Ammeter 1.0, CT,60/5A,CL-1,10VA For Metering-3 Nos., Indication Lamp (R-Y-B-ON-OFF) 6A SP MCB,10 KA- 6 Nos. etc. complete as per detailed dawing and instruction of Architect/EIC. |
| 43 | Supply, fixing, testing & commissioning ofLeGrand MCB( myrious) or equivalentmake 8way TPN DB "Incomer: 32A TPN MCB, Outgoing: 3 Nos. 32A DP RCCB (30 mA) and 18 Nos. 10/20A SP MCBs -10 KA etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 44 | Supply, Installation, testing and commissioning of the following luminaires, fixtures and fittings. The fixtures shall be installed on wall, ceiling etc. and as per the manufacturer instructions. The job also includes the connection of the fixture with outlet point using 3core flexible wire wherever the lighting fixtures are there etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 45 | (a) 18W LED , Surface Mounted downlighter complete with electronic ballast with THD<10% etc. all accessories as required of Philips(Ref. Cat. No. Led DN193-1200) or equivalent make etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 46 | (b) 9W LED bracket light of Philips or equivalent makes with screw etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 47 | (c) 12" exhaust fan of Philips or equivalent make with screw etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 48 | (d) 48" ceiling fan of compton or equivalent make with anchor fastener etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 49 | (e) Concealed night lamp 3 watt led type of Philips or equivalent make with screw etc. complete as per detailed drawing and instruction of Architect/EIC |
| 50 | (f) LED strip light of Philips or equivalent make of approved colour in the coving of false ceiling etc. completeas per detailed drawing and instruction of Architect/EIC. |
| 51 | Circuit Wiring Between Switchboxes using2.5 sq.mm wires for Phase & Neutral conductors and 1.5 Sq.mm wire for Earthing conductor etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 52 | Full points (Primary Points) Average Length of Circuit = 7 meters. Supply of the modular switches, modular Switchboxes, modular Power socket units, Grid, modular Cover Plates, Back Box and accessories is included in the scope. |
| 53 | Half points (Secondary Points) Average Length of Circuit = 5 meters. Supply of the modular switches, modular Switchboxes, modular Power socket units, Grid, modular Cover Plates, Back Box and accessories is included in the scope. |
| 54 | Supply, fixing, testing & commissioning of Main CKT 2.5Sq.mm X 2 Run+ 1.5Sq.mm X 1 Run Earth Wire with PVC conduit & accessories etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 55 | Providing, fixing, testing point Wiring of TV Point having RJ-6 socketwith all Accessories including box and modular cover plates for average length of 7 meter. |
| 56 | Supply and laying of 4 PAIR UTP LAN cable -CAT-6 in underground /wall in 1.5mm thick PVC pipe of 25mm dia. with proper junction box for maintenance purpose from server room to each work station . |
| 57 | Supply and testing of patch cord of Length 1 Meter CAT-6 |
| 58 | Providing and fixing LAN cable Face plate with RJ-45 socket |
| 59 | Supply and laying of 2 pair telephone wire ISI marked PVC Insulated 0.63m sqmm Copper conductor of internal wiring from EPBAX to the various tables as per the requirement complete in all respect as per the drawing and instructions of site engineer/ EIC - (Make D-link) |
| 60 | Providing and fixing of modular plate type telephone outlet on zinc plated & yellow passivated MS box with cover plate, grid plate, screwsetc with connections as required for Supply & installation of RJ - 11type Tel. Socket. (Make: Anchor Roma) |
| 61 | Supply, fixing, testing & commission of DB to 25A, AC Power Socket, using 4 sq. mm wires for Phase & Neutral conductors and 2.5 sq.mm wire for Earthing conductor including all accessories, power socket etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 62 | Supply, fixing and testing exhaust fan points (using 2.5 sq.mm. cu. wires) with 6A modular switch installed on switchboxes as per distributions schedule provided along with the other modular switches and 6A modular plug socket near Exhaust Fan etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 63 | Supply, fixing and testing 6A modular power plug points (with 2.5 sq.mm cu. wires) installed on modularswitchboxes as per distributions schedule provided along with the other modular switches etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 64 | Supply, fixing and testing DB to 16A, independent commercial modular type modular Power Socket, using 4 sq. mm wires for Phase & Neutral conductors and 2.5 sq.mm wire for Earthing conductor etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 65 | Supply, fixing and testing circuit wiring for Ceiling fan points with electronics step type modular regulator (using 2.5 sq.mm. Cu. Wires) installed on modular switchboxes as per distributions schedule provided along with the other switches etc. complete as per detailed drawing and instruction of Architect/EIC. |
| 66 | Supply, fixing and testing two way modular switch (with 1.5 sq.mm cu. wires) installed on modularswitchboxes as per distributions schedule provided etc. complete as per detailed drawing and instruction of Architect/EIC.Supply of the modular Switches, modular Switchboxes, modularSockets, Grid, modular Cover Plates, Back Box and accessories is included in the scope. |
| 67 | SUPPLYING AND FIXING CEILING FAN:- Supply,installation,testing and commissioning of ceiling fans of Bajaj /Crompton Greaves/ Khaitan/ Usha make only including supply and fixing of the electronic regulators with all necessary supports.All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge. 1400 MM SWEEP (WHITE) |
| 68 | SUPPLYING AND FIXING FRESH AIR/EXHAUST FAN :- Supply, installation, testing and commissioning of single phase,Fresh Air Fans/ Heavy duty Exhaust Fans of Bajaj/ Crompton Greaves/Khaitan/Usha make only including supply and fixing with all necessary supports All complete with labour and materials as per drawings,specifications and directions of Engineer-in-Charge.NOTE:Necessary civilworks required for fixing the exhaust fans shall be in the scope of Contractor. |
| 69 | SUPPLY AND FIXING TUBE LIGHT FITTINGS ON WALL:- Supply, fixing and connection of Philips / approved equivalent make tubelight fittings along withtubes(tubes cost will be paid separately) and control gear the necessary control gear fully wired up and fixing on existing TW varnished double board round blocks on wall including supply & fixing of round blocks,lead in wire,nuts,bolts,screws etc.All complete with labour and materials as per directions of Engineer-in-Charge. TYPE TCS 19/136 (HPF) indoor decorative luminaire with opal acrylic diffuser. |
| 70 | SUPPLY AND FIXING TUBELIGHT ON CEILING:- Supply, fixing and connection of Philips /approved equivalent make recessed type tube light fitting along with tubes (tubes cost will be paid separately),ISI markedel ecteronic ballast (wherever applicable) and control gear fully wired up and fixed on ceiling/ flushed with false ceiling including supply of necessary flexible wire and fixing materials.All complete with labour and materials as per directions of Engineer-in-Charge. TYPE TBS 50/ 236 (HPF) indoor decorative "widespread" mirror optics luminaire complete with all accessories. |
| 71 | ERECTION OF WALL BRACKET / CEILING FITTINGS WITH UPTO 2 GLS LAMPS:- Erection of wall bracket /ceiling fitting so fall sizes and shapes containing upto two GLS lamps per fitting,completewithall accessories including connection etc.as required. |
| 72 | Electric substation Supply, Installation, Testing and Commissioning of , Outdoor type EB-DG Panel and Stabilizer panel |
| 73 | PLUMBING & SENETARY FIXTURES |
| 74 | WC : Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 75 | Concealed cistern with stand and flush control plates model for reference: jaquar catalog no. CIS-CHR-31204019or equivalent: Supplying & FixingConcealed cistern with stand and flush control plates of jaquaror equivalent makefixed with Nut Bolts or as per the Manufacturer specification, fixing the cistern on to wall with suitable teak wood Plugs, Sheet Metal screws, Cutting Masonry or concrete surfaces, restoring damaged portions with Cement Mortar (1:4) mixed with polymer & 6mm thk size stone metal, scaffolding, carting away the debris of compound, cleaning etc. complete as per instructions of Architect/EIC. |
| 76 | Urinal : Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 77 | Wash basin model for reference: RUBIC TABLE TOP BASIN ( L610 W385H130 MM or equivalent as approved by Architect ) ( MAKE:SIMPOLO equivalent): providing & fixing glazed vitreous table top wash basin of pattern as approved by Architect of Simpolo or equivalent make as approved by Architect/EIC with necessary waste coupling, wall flange bottle trap of Simpolo/ jaquar or equivalent make with MS or CI brackets painted white, C.P. brass chain with rubber plug, etc. including cutting & making good the walls & floors wherever required complete in all respects inclusive of cost of all required fittings, fixtures, materials, labour, tools, tackles etc. as per specification and instruction of Architect/EIC. |
| 78 | providing & fixing exposed type spout of Kubix-F series of jaquar or equivalent make with necessary wall flange, nipple etc. completeas per detailed drawing and instruction of Architect/EIC. |
| 79 | Providing and fixing single lever tall boy with 200mm extension body fixed spout without Popup waste system with 600mm long braided hoses of Kubix-F series of jaquar Make (Ref. jaquar Cat. No. KUB-35009FB) or equivalent make including cutting and making good the walls where required complete in all respects as per direction of Engineer-in-Charge. |
| 80 | PVC floor trap (NAHAHI TRAP) Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Sand cast iron S&S as per IS - 3989 |
| 81 | Providing and fixing S S Cockroach trap of Jayana or approved make and quality, complete in all respects; inclusive of cost of all materials, labour, tools, tackles etc. as per specifications and direction of EIC. |
| 82 | Providing and fixing copper connection pipe minimum 2 ft long of jaquar or equivalent make for wash basin and geyser connection etc. complete inclusive of all tools, tackles, labour, material etc. as per specification & direction of Architect/EIC. |
| 83 | Providing & Fixing in position heavy duty concealed angular stop cock with wall flange of Kubix-F series of jaquar Make (Ref. jaquar Cat. No. KUB-35053F) or equivalent make including non-return valve, cutting of wall, making good the wall, sealing of joints, taflon taping, testing etc. complete in all respect inclusive of cost of all material, labour, tools, tackles etc. as per instructions of the Architect / EIC. |
| 84 | Providing & Fixing in position extra heavy duty concealed flush cock with wall flange 25mm of Kubix-F series of jaquar Make (Ref. jaquar Cat. No. KUB-35081F) or equivalent make including non-return valve, cutting of wall, making good the wall, sealing of joints, Teflon taping, testing etc. complete in all respect inclusive of cost of all material, labour, tools, tackles etc. as per instructions of the Architect / EIC. |
| 85 | CPVC pipes of dia. 15mm :Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.15 mm nominal dia Pipes |
| 86 | CPVC pipes of dia. 25mm :Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.25 mm nominal dia Pipes |
| 87 | CPVC pipes of 50mm : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge..50 mm nominal dia Pipes |
| 88 | CPVC pipes of 100mm : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.100 mm nominal dia Pipes |
| 89 | 50mm ball cock : Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 50 mm nominal bore, 242mm long, weighing not less than 1240 gms |
| 90 | providing & fixing two way bib cockof Kubix-F series of jaquar Make (Ref. jaquar Cat. No. KUB-35041F) or equivalent approved make by Architect/EIC includingcutting of wall, making good the wall, sealing of joints, Teflon taping, testing etc. complete in all respect inclusive of cost of all material, labour, tools, tackles etc. as per instructions of the Architect / EIC. |
| 91 | Providing & fixing Angle Valve(Ref. Make: JAQUAR, Model: Cat. No. 563 or approved equivalent) and Health Faucet with flexible tube 8mm diameter x 1.5 m long (Ref. Make: JAQUAR, Model: Cat. No. 549 or approved equivalent). |
| 92 | providing & fixing 4 way diverter for concealed fitting with built-in non return valves with divertor handle of Kubix-F series of jaquar Make (Ref. jaquar Cat. No. KUB-35421F) or equivalent approved make by Architect/EIC includingcutting of wall, making good the wall, sealing of joints, Teflon taping, testing etc. complete in all respect inclusive of cost of all material, labour, tools, tackles etc. as per instructions of the Architect / EIC. |
| 93 | Providing & fixing overhead shower 200x200mm square shape single flow( ABS body chrome plated with gray face plate ) with rubit cleaning system of jaquar Make (Ref. jaquar Cat. No. OHS 35497) or equivalent make including shower Arm of 20mm dia. & 600mm Long round shape with 90° bend for wall mounted showers with flange of approved make by Architect/EIC includingcutting of wall, making good the wall, sealing of joints, Teflon taping, testing etc. complete in all respect inclusive of cost of all material, labour, tools, tackles etc. as per instructions of the Architect / EIC. |
| 94 | SINK : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :470x420 mm bowl depth 178 mm WITHOUT DRAIN BOARD |
| 95 | Master cock : supplying and fixing 50 mm master cock |
| 96 | DOORS AND WINDOWS |
| 97 | New wooden doors : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 98 | WINDOWS : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made : Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). |
| 99 | PARTLY FIXED - PARTLY LOUVERS WINDOW ANODIZED FOR TOILETS (Tentative size: 2"0"x 2"0" ): Provide and Fixing aluminum partly fixed adjustable louver (Anodized) made out of 2" X 1 1/2" X 1.6 mm Aluminum Tubular Sections around, center along with 4nos. of 5.5mm thick 4" wide textured glass louvers including louvers frame along with 5.5mm thick shelf design textured glass fixed with 12mm X 12mm X 1.5mm thk aluminum square beading, scaffolding, carting away debris out of compound, cleaning the site etc. complete as per site requirements and the instructions of Architect/EIC. Mode Of Measurement - Length X Width |
| 100 | POP PUNNING Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 101 | COLOR PAINT |
| 102 | LUSTER PAINTING: Providing and Applying3 coats of luster paint of approved make and approved shade on new or old structure, walls, beams, columns, ceilings etc. including scrapping, cleaning and preparing the surfaces with 2 coats of primer along with applying birla putty to the surfaces including scaffolding, cleaning the floors, fittings, furnitures, handles, ladders, glasses, removing of debris out of compound, cleaning the site etc. complete as per the instructions of Architect / EIC. Mode of Measurement - Length X Height |
| 103 | INTERIOR PAINT: Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer. Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour |
| 104 | ENAMEL PAINT: Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work |
| 105 | Exterior paint : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 106 | MODULAR KITCHEN CABINET BELOW PLATFORM (Tentative size per compartment: 2"0"x2"0"x2"6") providing & fixing modular kitchen cabinet with 18mm BWR plyfor verticals, sides, shutters of below counter cabinet including for drawers sides etc. with 1mm thk approved make laminate on all exposed surface and inside surface with 0.8mm thk approved make laminate fixed with approved S. S Hinges, s.s handle, telescopic slides for drawers etc. complete as per detail drawing and instructions of Architect/EIC. ( Mode Of Measurement : Length X Width of front surface ) |
| 107 | Compound wall |
| 108 | Common area plumbing & drainage |
| 109 | Common area electrification, street light etc |
| 110 | Garden & Horticulture |
| 111 | Main gate 1 |
| 112 | Main gate 2 |
| 113 | under ground watertank |
| 114 | Overhead water tanks |
| 115 | Road |
| 116 | Supplying and laying bituminous carpet of 75mm thick for sand pad in two layers using Bitumen of grade VG-10, @100kg/Cum of sand grit of fineness modulus 3.5max. Including making slope in the sand pad including rolling the surface with Hand roller. Item includes laying of 1000 micron (1mm) black LDPE liner as per IS 2508 under the desired layer of sand |
| 117 | Supply and laying of water bound macadam of 100 mm consolidated thickness for subbase with 90 to 45 mm stone aggregate,11.2mm size screenings, chippings of stone and murrum spreading, watering and consolidating in camber with power roller complete as/specifications. |
| 118 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge. |
| 119 | :i) On W.B.M. @ 0.75 Kg / sqm. Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :On W.B.M. @ 0.75 Kg / sqm |
| 120 | ii) On bituminous surface @ 0.50 Kg / sqm. Providing and applying tack coat using hot straight run bitumen of grade VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications : |
| 121 | Providing and laying bitumen mastic wearing course (as perspecifications) with industrial bitumen of grade 85/25 conforming to IS : 702, prepared by using mastic cooker and laid to required level and slope, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of approved size at the rate of 0.005 cum per 10 sqm and at approximate spacing of 10 cm centre to centre in both directions, pressed into surface protruding 1 mm to 4 mm over mastic surface, including cleaning the surface, removal of debris etc. all complete. (Considering bitumen using 10.2% as per MORTH specification). 40 mm thick |
| 122 | SEAL COAT : Providing and laying seal coat over prepared surface of road with bitumen heated in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road surface, including rolling and finishing with power road roller all complete. Note: Seal coat items to be operated only with the prior approval of chief Engineer concerned |
| 123 | Front gate signage & elevation treatment |
| 124 | Backside gate signage & elevation treatment |
| 125 | FORM WORK :Centering and shuttering including strutting, propping etc. and removal of form for all heights : |
| 126 | Foundations, footings, bases of columns, etc. for mass concrete |
| 127 | Suspended floors, roofs, landings, balconies and access platform |
| 128 | Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 129 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 130 | Stairs, (excluding landings) except spiral-staircases |
| 131 | Weather shade, Chajjas, corbels, etc. including edges. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
