Indian Oil Corporation Limited-IOCL has published Tender For Repair And Maintenance Of Civil Works At Ppmc Polymer Terminal, Panipat. Submission Date for this Tender is 23-04-2024. Civil Work Tenders in panipat Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Carriage of lime, moorum, building rubbish and debris including refractory / insulation debris etc. by mechanical transport for following leads or part thereof including loading, unloading and stacking all complete as per the direction of the Engineer-in-Charge (The rates will be applicable to net quantities after deduction of 20 percent for voids): |
| 2 | Upto a lead of 1 km |
| 3 | Lead beyond 1 km but upto 2 km. |
| 4 | Carriage of earth by mechanical transport for following leads or part thereof including loading, unloading and stacking all complete as per the direction of the Engineerin-Charge (The rates will be applicable to net quantities after deduction of 20 percent for voids): |
| 5 | Upto a lead of 1 km |
| 6 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed : All kinds of soil. |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m |
| 8 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil: |
| 9 | Pipes, cables etc. not exceeding 80 mm dia |
| 10 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. |
| 11 | Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level : |
| 13 | 1:1½:3 (1 Cement : 1½ coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 14 | 1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 15 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centring, shuttering and finishing: |
| 16 | 1:1½:3 (1 cement:1½ coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 17 | 1:2:4 (1 Cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 18 | Centring and shuttering including strutting, propping etc. and removal of form work for: |
| 19 | Foundations, footings, bases for columns |
| 20 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 21 | Columns, piers, abutments, pillars, posts and struts. |
| 22 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. Note: The unit "Each" stands for "each cement bag of 50 KG" |
| 23 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 24 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 25 | 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 26 | 1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 27 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level: |
| 28 | Thermo-Mechanically Treated bars |
| 29 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level: |
| 30 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 31 | Providing and filling in position bitumen mix filler of proportion 80 kg. of hot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand for expansion joints. |
| 32 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 33 | Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 34 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 35 | Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 36 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level: |
| 37 | Cement mortar 1:4 (1 cement :4 coarse sand). |
| 38 | Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry. |
| 39 | Stone tile work for wall lining up to 10 m height with special adhesive over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge). |
| 40 | Granite stone of any colour and shade |
| 41 | Raj Nagar plain white marble/ Udaipur green marble/ Zebra black marble |
| 42 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 43 | Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble - Area of slab over 0.50 sqm |
| 44 | Granite of any colour and shade - Area of slab over 0.50 sqm. |
| 45 | Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete. |
| 46 | Providing and fixing expansion hold fasteners on C.C./ R.C.C./ Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Wedge expansion type: |
| 47 | Fastener with threaded dia 10 mm |
| 48 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 49 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : |
| 50 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 51 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I) - On one side only. |
| 52 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) : |
| 53 | Rectangular or square. |
| 54 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with: |
| 55 | With 5.5 mm thick glass panes. |
| 56 | Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : |
| 57 | 25 mm dia (heavy type). |
| 58 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete: |
| 59 | Fixed to openings /wooden frames with rawl plugs screws etc |
| 60 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : |
| 61 | 125x64x2.50 mm. |
| 62 | 100x60x2.50 mm. |
| 63 | 75x50x2.50 mm. |
| 64 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 65 | 300x16 mm. |
| 66 | 250x16 mm. |
| 67 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 68 | 300x10 mm. |
| 69 | 250x10 mm. |
| 70 | Providing and fixing aluminium tee channels (heavy duty)with rollers, stop end in pelmets as curtain rod. |
| 71 | Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door with necessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. |
| 72 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 35 kg and door width up to 700 mm) with necessary accessories and screws etc. complete |
| 73 | Providing and fixing factory made UPVC door frame made of UPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge: |
| 74 | Extruded section profile size 48x40 mm. |
| 75 | Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer"s specifications and direction of Engineer-in-charge: |
| 76 | Decorative finish (both side wood grained finish). |
| 77 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality: |
| 78 | 1.5 mm thick. |
| 79 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 80 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying a priming coat of approved steel primer: |
| 81 | M.S. tube. |
| 82 | G.I. pipes. |
| 83 | Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar including filling the joints with same mortar with common burnt clay F.P.S. (non modular) bricks: |
| 84 | 1:4 (1 cement : 4 coarse sand). |
| 85 | Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar including filling the joints with same mortar with common burnt clay F.P.S. (non modular) bricks: |
| 86 | Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar including filling joints with Jamuna sand (with common burnt clay F.P.S. (non modular) bricks) complete. |
| 87 | Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-incharge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : |
| 88 | Raj Nagar plain. |
| 89 | Udaipur green marble. |
| 90 | Pink plain marble. |
| 91 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. |
| 92 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 93 | 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement :5 coarse sand) with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar: |
| 94 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 95 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption"s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete: |
| 96 | Size of Tile 600x600 mm. |
| 97 | Size of Tile 800x800 mm. |
| 98 | Size of Tile 1000x1000 mm. |
| 99 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge: |
| 100 | Size of Tile 600x600 mm. |
| 101 | Size of Tile 800x800 mm. |
| 102 | Size of Tile 1000x1000 mm. |
| 103 | Deduct for not using 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles. |
| 104 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75mm deep chase. |
| 105 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm or both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 106 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 (Part I) : 2011 (Board with BIS certification marks). |
| 107 | 12.5 mm thick tapered edge gypsum moisture resistant board. |
| 108 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 109 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : |
| 110 | With cement mortar 1:4 (1 cement : 4 fine sand). |
| 111 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 112 | Neat cement punning. |
| 113 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. Note: The unit (Each) EA is to be read as "Per bag of 50 Kg cement used in the mix". |
| 114 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 115 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade - Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture. |
| 116 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade- New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. |
| 117 | Applying a coat of mordant solution on G.S. sheet : |
| 118 | With a solution of 38 gms of copper acetate in a litre of soft water. |
| 119 | Lettering with black Japan paint of approved brand and manufacture. Note: Rate EACH (EA) stands for "Per letter per cm height". |
| 120 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 121 | Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface). |
| 122 | Providing & fixing white vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c media, all complete as per the direction of Engineer-in- charge: |
| 123 | Long pattern W.C Pan of size 580 x 440 mm. |
| 124 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge: |
| 125 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix). |
| 126 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 127 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: |
| 128 | In cement mortar. |
| 129 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: |
| 130 | Of area 3 sq. metres and below. |
| 131 | Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metreslead as perdirection of Engineer-in- charge. |
| 132 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead: |
| 133 | For thickness of tiles 10 mm to 25 mm. |
| 134 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 135 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 136 | 1:4 (1 cement: 4 fine sand). |
| 137 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 138 | Laying water bound macadam sub-base with brick aggregate and binding material, earth etc. including screening, sorting and spreading to template and consolidation with light power road-roller etc. complete.(payment for brick aggregate and moorum etc. to be made separately): |
| 139 | Over burnt (Jhama) brick aggregate 90 mm to 45 mm. |
| 140 | Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting, mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately: |
| 141 | Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer. |
| 142 | Providing and laying in position bitumen hot sealing compound for expansion joints etc. - Using grade ‘A’ sealing compound. Note: Unit "Metre"(M) shall be read as "Per cm depth per cm width per m length". |
| 143 | Providing and fixing water closet squatting pan (Indian type W.C. pan )with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : |
| 144 | White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. |
| 145 | Providing and fixing white vitreous china water closet squatting pan (Indian type): |
| 146 | Long pattern W.C. pan of size 580 mm. |
| 147 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 148 | W.C. Pan with ISI marked white solid plastic seat and lid. |
| 149 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete: |
| 150 | 10 litre capacity - White. |
| 151 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm or 340 x 410 x 265 mm sizes respectively. |
| 152 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 153 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. |
| 154 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 155 | Kitchen sink with drain board - 510x1040 mm bowl depth 250mm. |
| 156 | Providing and fixing 8mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in-charge. |
| 157 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: |
| 158 | Semi rigid pipe - 32 mm dia. |
| 159 | Providing and fixing toilet paper holder : |
| 160 | Vitreous china. |
| 161 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: |
| 162 | Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms. |
| 163 | Providing and fixing PTMT Bottle Trap for Wash basin and sink: |
| 164 | Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms. |
| 165 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour. weighing not less than 105 gms. |
| 166 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour. Weighing not less than 88 gms. |
| 167 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 168 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge: Internal work - Exposed on wall: |
| 169 | 15 mm nominal outer dia pipes. |
| 170 | 20 mm nominal outer dia pipes. |
| 171 | 25 mm nominal outer dia pipes. |
| 172 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge: Concealed work including cutting chases and making good the walls etc: |
| 173 | 15 mm nominal dia pipes. |
| 174 | 20 mm nominal dia pipes. |
| 175 | 25 mm nominal dia pipes. |
| 176 | Providing and fixing brass bib cock of approved quality : |
| 177 | 15 mm nominal bore. |
| 178 | 20 mm nominal bore. |
| 179 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 180 | 25 mm nominal bore. |
| 181 | 32 mm nominal bore. |
| 182 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 183 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 - 15 mm nominal bore. |
| 184 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. - 15 mm nominal bore. |
| 185 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore. |
| 186 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 - 15 mm nominal bore. |
| 187 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore. |
| 188 | Providing and fixing C.P. brass extension nipple (size 15mm x 50mm) of approved make and quality as per direction of engineer-in-charge. |
| 189 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 190 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 191 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete - up to 5mm depth and 5 mm width. |
| 192 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. |
| 193 | Pre-laminated particle board with decorative lamination on both sides. |
| 194 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 195 | With float glass panes of 4.0 mm thickness. |
| 196 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour: |
| 197 | 15 mm nominal bore with 30cm length. |
| 198 | Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg. |
| 199 | VENETIAN BLINDS |
| 200 | Skilled Worker (Plumber/Carpenter etc.)* |
| 201 | Semi-Skilled Worker (Helper to plumber/carpenter etc.) * |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
