|
| 1 | M&L for comprehensive maintenance and repairs / rectification of deffects by electrically and technicallyby checking all indicators, SMPS, mother board, card , electrical connections and replacement of faulty service parts of complete with wire or wireless fire alarm system of any make and model installed in variours OTM BLDG & MAP md accn of Camero Areaall as specified and as directed by Engineer-in-charge. |
| 2 | NOTE FOR ITEM NO 1ABOVE :- ALL DEFECTIVE PART WHICH ARE REQUIRED TO REPLACE SHALL BE MEASURED AND PAID SEPERATELY UNDER RESPECTIVE ITEMS AS SUPPLY ONLY (a) FIRE ALARM CONTROL PANEL : The functions of controls panel and indicating equipmentwill be checked by the operation of a trigger device in each zone. All fault indicator and their circuits will be checked by stimulation of fault conditions of any type fie alarm panel.(b) HEAT DETECTOR : Heat detectors will be tested by aim a heat lamp, blow-dryer, or heat gun at the heat detector. The detector alarms should sound within three or four seconds after apply the heat source.(c) SMOKE DETECTOR : Smoke detector will be cleaned periodically so as to remove dust or dirt that accumulates on them due to local ambient conditions at least each detector is cleaned once in month. Smokedetectors will be tested by apply a small spray of smoke detector test aerosol. The detector alarms should sound within three or four seconds after apply the heat source. |
| 3 | (d) MANUAL CALL POINT HOOTERS : All manual call points will be operated once a monthly by removing glass or by actual breaking of glass so as to ensure that system is capable of operation under alarm conditions and all hooters give proper sound(e) RESPONSE INDICATORS : All detectors which are placed in side a cabin of room will be tested by initiating the particular detector so as to ensure the proper working of response indicator (f) WIRING & CABLES : A visual inspection will be made so that structure or occupancy changes does not damage cables and sitting of trigger devices (manual call points smoke detector and heat detector.(g) MONTHLY LOG SHEET WILL BE MAINTAINED FOR MONTHLY INSPECTION AND TESTING : Monthly inspection and testing will be done in the monthly maintained log sheet. Log sheet will be produced to the Engineer-in-charge duly complted on Ist day of every month. |
| 4 | NOTE :- (a) Replacement of parts will be measured and paid seperately. (b) If service is not carried out by the contractor on due date Rs 1000.00 per day for each service recovery will be made.(c) Contractor will provide One Technician and One helper from 0900 to 1700 hrs in all working days for day to day services.(d)The maint shall be carried out through manufacturer representative or his authorised rep. |
| 5 | Supply, installation, testing and commissioning in replacement of Intelligent Analog Addressable MuliticriteriaType Detector Complete with Dual LED, Hard Addressable Having rotary decade Address swicthes from 01-99, complete with Mounting Base Complete as required Conforming to BS 5839 Standards and Duly Approved by EN54/LPCB//UL complete all as specified and directed by Engineer-in-Charge. |
| 6 | Supply, installation, testing and commissioning in replacement of fault isolator with base with termination preferably after every 20–30 devices and shall be able to isolate electrical short circuit in the wiring etc. as required complete all as specified and directed by Engineer-in-Charge. |
| 7 | Supply, installation, testing and commissioning in replacement of Intelligent Analog Addressable Type Manual Call Point having Surface or flush mounting Option fully complaint to EN54 having Rotary Decade Swicthes for Addressing from 01-99 complete with Back Box for Mounting Complete as required conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 8 | Supply, installation, testing and commissioning in replacement of Response Indicators for getting fire indications of detectors installed above false ceiling area interconnecting to loop cable complete all as specified and directed by Engineer-in-Charge. |
| 9 | Supply, installation, testing and commissioning in replacement of Intelligent Analog Addressable Type Control/Output Modules having option of RAIL or Surface Mounting with Tri Colour LED status Indicator with Built in Short Circuit Isolators having Visible Rotary Decade Address Swicthes from 01-99, for initiating Hooter/Sounder/Strobes etc dully approved to GEA GE1-082conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 10 | Supply, installation, testing and commissioning in replacement of Intelligent Analog Addressable Type Monitor Modules having option of RAIL or Surface Mounting with Tri Colour LED status Indicator with Built in Short Circuit Isolators having Visible Rotary Decade Address Swicthes from 01-99 dully approved to GEA GE1-082 conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 11 | Supply, installation, testing and commissioning in replacement of Analog Addressable type Active/ Passive Repeater Fire Alarm panel with Backlit LCD Display, having Controls For Reset, Mute, Accept , Silence alarms and Self Test Conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 12 | Supply, installation, testing and commissioning in replacement of Addressable Type Loop Powered Hooter Cum Strobe complete with Mounting Base as required conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 13 | Supply, installation, testing & commissioning in replacement of 5 Loop Micro processor based 2 wire fault tolerant loop, required loop networkable type (each loop accessing maximum 99 detectors and 99 modules ) fire alarm/detection control panel. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes. Further, the panel must be able to automatically switch ON /OFFrespective control module when ever any alarm is triggered. The panel shall have rectifier, Loop cards, 80 character L C D unit to indicate Fire/Fault Signal with address and analog output, external/inbuilt printer to log all fire or fault events complete in all respects.The Panel Shallbe Sheet Steel Painted, selaed to IP30. The Panel Shall have 20 Zones with Individual LEd Indicators, expandable to 80 LED Indicators. The Panel Shall have 3 Serial Ports. The panel shall have a built in power supply and battery charger along with maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable of running for a minimum of 24 hours with battery charger complete as required.and as per specifications. conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 14 | Supply & fix in replacement of4\"x4\" MS junction box for detector mounting complete all as specified and directed by Engineer in Charge. |
| 15 | Supply & fix in replacement ofbattery maintenance free 6 volt 7 AH complete all as specified and directed by Engineer in Charge. |
| 16 | Supply & fix in replacementofzone card for fire alarm panel complete all as specified and as directed by Engineer-in-charge |
| 17 | Supplying, drawing, connecting, testing & commissioning in replacement of 2core, 1.5 sq. mm. stranded copper conductor, pvc insulated PVC sheathed,aluminium myler tape shielded FRLS wire in existing conduit complete all as specified and directed by Engineer-in-Charge. (For Fire Detection & Alarm System) |
| 18 | Supply and laying in position in replacement of the following sizes of 25/20mm Dia PVC. conduits including providing all accessories complete all as specified and directed by Engineer-in-Charge. (For Fire Detection) |
| 19 | S & F in replacement of Loop driver card suitable for fire alarm/detection control panel complete all as specified and directed by Engineer-in-Charge. |
| 20 | S & F in replacement of RS 485 Communication module complete all as specified and directed by Engineer-in-Charge. |
| 21 | S & F in replacement of Internal Printer Module complete all as specified and directed by Engineer-in-Charge. |
| 22 | S & F in replacement of Modbus TCP/IP interface module. Requires an RS485 card to be fitted in the control panel & MI-RJ-45 Cable complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply and fixing in replacement of Photoelectric smoke detector detects the smoke by a couple of infrared diodes. The principle of detection isgranule in the smoke can re act infrared light. In orderto reduce the interference and lower power consumption, the emitting circuit adopts the pulse signal. Theproduct in accordance with the networking approach is divided into 2-wire and 4-wire detectors complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply and fixing in replacement of SITC Red Conventional Call point with LED and Resistor 470 OHM Flush Mounting Flexi Element complete all as specified and directed by Engr-in-charge. |
| 25 | Supply and fixing in replacement of SITC Conventional HOOTER cum Strobe Flush Mounting Flexi Element complete all as specified and directed by Engr-in-charge. |
| 26 | Supply, installation, testing & commissioning in replacement of 2 Loop Micro processor based 2 wire fault tolerant loop, required loop networkable type (each loop accessing maximum 99 detectors and 99 modules ) fire alarm/detection control panel. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes. Further, the panel must be able to automatically switch ON /OFFrespective control module when ever any alarm is triggered. The panel shall have rectifier, Loop cards, 80 character L C D unit to indicate Fire/Fault Signal with address and analog output, external/inbuilt printer to log all fire or fault events complete in all respects.The Panel Shallbe Sheet Steel Painted, selaed to IP30. The Panel Shall have 20 Zones with Individual LEd Indicators, expandable to 80 LED Indicators. The Panel Shall have 3 Serial Ports. The panel shall have a built in power supply and battery charger along with maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable of running for a minimum of 24 hours with battery charger complete as required.and as per specifications. conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA complete all as specified and directed by Engineer-in-Charge. |
| 27 | M & L for Charges for attending and rectifying the Door sensor minor complaints (control panels, motor and all electrical complaints) as and when required for smooth operation of Door sensor as when required to be replace unsvfollowing spare parts after replacement testing shall be carried out as directed by Engineer-in-chargeNote :- Following spare parts shall be measured and paid separately |
| 28 | Supply and fix in replacement of Radar XL-C 4102 A for door sensor for one door including taking down unsv parts and fixing new parts in same position without damaged other itemsall as specified and directed by Engr - In - Charge |
| 29 | Supply and fix in replacement of control unit assembly XL-C 4106 for door sensor for one/two door including taking down unsv parts and fixing new parts in same position without damaged other items all as specified and directed by Engr - In - Charge |
| 30 | Supply and fix in replacement of Motor assembly for 4100 of XL-C 4107 for door sensor for one/twodoor including taking down unsv parts and fixing new parts in same position without damaged other items all as specified and directed by Engr - In - Charge |
| 31 | Supply and fix in replacement of Torroidal transformer XL-C 4108 for door sensor for one door including taking down unsv parts and fixing new parts in same position without damaged other items all as specified and directed by Engr - In - Charge |
| 32 | Supply and fix in replacement of Main roller assembly for 4100 ofXL-C 4109 for door sensor for one door including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut bolt all as specified and directed by Engr - In - Charge |
| 33 | Supply and fix in replacement of counter roller assembly for 4100 ofXL-C 4110 for door sensor for one door including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut bolt all as specified and directed by Engr - In - Charge |
| 34 | Supply and fix in replacement of encoder Cable 450mm XL-C 4111 for door sensor including taking down unsv parts and fixing new parts in same position without damaged other items with proper clamps and securing all as specified and directed by Engr - In - Charge |
| 35 | Supply and fix in replacement of Five position prog switchXL-C 4112 for door sensor including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut boltall as specified and directed by Engr - In - Charge |
| 36 | Supply and fix in replacement of light barrier for 4100 of XL-C 4113 for door sensorincluding taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut bolt all as specified and directed by Engr - In - Charge |
| 37 | Supply and fix in replacement of Timer belt, fixing accessaries of XL-C 4117 for door sensor including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut boltall as specified and directed by Engr - In - Charge |
| 38 | Supply and fix in replacement of Carrier head assembly of XL-C 4119 for door sensor including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut boltall as specified and directed by Engr - In - Charge |
| 39 | Supply and fix in replacement of Floor guide for framed aluminium doorfor door sensor including taking down unsv parts and fixing new parts in same position without damaged other items with proper screwes and nut boltall as specified and directed by Engr - In - Charge |
| 40 | Taking down carefully copper/aluminium point wiring( light ,fan, socket or power) complete,fitting such as switches, ceiling roses,pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc.Complete all as specified and directed by Engineer-in-Charge. |
| 41 | M&L for point wiring with single core of FRLS PVC insulated unsheathed ISI marked 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm drawing through in and including PVC conduit size of not less than 20 mm including conduit fittings and accessories concealed in wall / ceiling wiring on ceiling /wall terminated in flush metal box alongwith outer cover plate for mounting modular/piano switch, socket and electronic regulator along with provn ofearth wire of PVC insulated, unseathed,1100 V grade cable multi stranded FRLS ISI markedcopper conductor of size 1.5 sqmm all asspecified and directed by Engr-in-Charge. For One light point controlled by one switch one way. |
| 42 | All as per srl item38 above but for one ceiling fan / Exhaust fan point controlled by one switch regulator. |
| 43 | All as per item No 38 above but for one 3 pin 5 amps socket outlet on indipendent board with other switchs. |
| 44 | All as per item No 38 above but for one 3 pin 5 amps socket outlet on the same board with other switchs. |
| 45 | All as per item No 38 above but for one light point controlled by two way switches. |
| 46 | All as per item No 38 above but for Call bell controled by one push button in indipendent board . |
| 47 | All as per item No 38 above but with 2.5 Sq mm cable for Independent one 3 pin 15 Amps socket outlet In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire. |
| 48 | M&L for point wiring for one light fitting / one fan point controled by one switch with 1.5 Sq mm PVC insulated copper conductor cable drawing in and including PVC Casing/capping or surface conduit with 1.5 Sq mm PVC insulated copper conductor cable for continuous earth wire connected to main earth dolly with 3mm thick plastic laminated sheet cover completefor one light point controlled by one switch complete all as specified and directed by Engineer in Charge. |
| 49 | All as per srl item45 above but for one fan point controlled by one switch through regulator. |
| 50 | All as per srl item 45 above but for one 5 pin 5 amps socket outlet on the independent board. |
| 51 | All as per item No 45 above but for one 3 pin 5 amps socket outlet on the same board with other switchs. |
| 52 | All as per item No 45 above but for Call bell point. |
| 53 | All as per item No 45 above but with 2.5 Sqmm PVC insulated stranded copper conductor cable for one 3 pin 15 Amps socket outlet. In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire. |
| 54 | M&L for point wiring with 1.5sqmm PVC insulated unsheathed multi stranded copper conductor cable drawing in existingsteel/PVC conduit with 1.5 Sq mm PVC insulated copper conductor cable for continuous earth wire connected to main earth dolly excluding 3mm sheet metal box and hylam sheet completefor one light point controlled by one switch complete all as specified and directed by Engineer in Charge. |
| 55 | All as per srl item51 above but for one fan point controlled by one switch through regulator. |
| 56 | All as per srl item 51 above but for one 5 pin 5 amps socket outlet on the independent board. |
| 57 | All as per item No 51 above but for one 3 pin 5 amps socket outlet on the same board with other switchs. |
| 58 | All as per item No 51 above but for one light point controlled by two way switches. |
| 59 | All as per item No 51 above but for Call bell point. |
| 60 | All as per item No 51 above but with 2.5 Sq mm PVC insulated stranded copper conductor cable for one 3 pin 15 Amps socket outlet. In and including S/C 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR cable for continuous earth wire. |
| 61 | S&Fin replacement switch piano, flush type single pole, one way, 5 Amps, 240 volts all as specified and directed by Eng-in-charge. |
| 62 | S&Fin replacementswitch piano, flush type single pole, one way, 15 Amps, 240 volts all as specified and directed by Eng-in-charge. |
| 63 | S&Fin replacement switch piano, flush type single pole, two way, 5 Amps, 240 volts all as specified and directed by Eng-in-charge. |
| 64 | S&Fin replacement socket16 Amps, 2 in 1, flush type all as specified and directed by Eng-in-charge. |
| 65 | Supply & fix in replacementbell push, flush type, 5 Amps, 240 volts all as specified and directed by Eng-in-charge. |
| 66 | S&Fin replacementFan Regulator step type 120 watt, 240 volt complete. |
| 67 | S & F Modular switch 1 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge. |
| 68 | S & FModular Socket, 6A - 2/3 pin combined 2 module,suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge. |
| 69 | S & F Modular switch 2 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge. |
| 70 | S&FModular switch 1 way 16A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge. |
| 71 | S & FModular Socket, 16A 2/3 pin combined 2 module,suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge. |
| 72 | Supply and fixModular bell push 1 Module 5 Amps suitable for 240 volt Complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply and fixModular electronic Fan Regulator rotary flush step type 120 watt, 240 volt complete |
| 74 | Supply and fix White cover plate with frame,2 module Complete all as specified and directed by Engineer-in-Charge. |
| 75 | Supply and fix White cover plate with frame,3 module Complete all as specified and directed by Engineer-in-Charge. |
| 76 | Supply and fix White cover plate with frame,4 module Complete all as specified and directed by Engineer-in-Charge. |
| 77 | Supply and fix White cover plate with frame,6 module Complete all as specified and directed by Engineer-in-Charge. |
| 78 | Supply and fix White cover plate with frame,8 module Complete all as specified and directed by Engineer-in-Charge. |
| 79 | S & FModular metal flush box 3 module Complete all as specified and directed by Engineer-in-Charge. |
| 80 | S & FModular metal flush box 4 module Complete all as specified and directed by Engineer-in-Charge. |
| 81 | S & FModular metal flush box 6 module Complete all as specified and directed by Engineer-in-Charge. |
| 82 | Supply only in replacement Electric calling Bell Ding Ding Type suitable for 230 volts complete all as specified and directed by Engr-in-charge. |
| 83 | Supply and fixingin replacement ceiling roses, surface bakelite 65x50mm ,3 terminals3 phase, PVC/Polycarbonate, isolated bodyall as specified and directed by Eng-in charge |
| 84 | Supply and fixing in replacementPVC gang box suitable for one switch/socket 5 Amps complete with screw and necessary arrangement complete all as specified and directed by Engineer in Charge. |
| 85 | All as per srl item 81 above but for one 15 amps switch/socket outlet. |
| 86 | Supply & fix in replacementmetal clad socket single pole and neutral sheet metal enclosure with and 20A earth plug and socket complete with one single pole MCB 20 amp 240 Volts all as specified and directed complete all as specified and as directed by Engineer-in- charge. |
| 87 | Supply& fix in replacement of MCCB four Pole 250 Amps, 415 volt thermal release bearing adjestable type breaking cap 36 KA, comlete all as specified and as directed by Engineer-in-Charge. |
| 88 | Supply& fix in replacement of MCCB four Pole 125 Amps, 415 volt thermal release bearing cap 16 KAcomlete all as specified and as directed by Engineer-in-Charge. |
| 89 | M & L for rigid non metalic PVC medium grade conduit including junction boxes, tee, bends, elbows, reducers bell mouth tube ends,fixing accessories such as couplers, lock Nuts, saddle pipe hook etc for 25 mm dia.ISI Marked. |
| 90 | Supply & fix in replacement of Casing capping double lock type supper qualitysize 20 mm width ISI marked with fixing accessoriescomplete all as specified and directed by Engineer in Charge. |
| 91 | Cutting grooves in brick wall, 75 mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 |
| 92 | Taking down of LED/Tube light/CFL fitting of any type of make and removing material to store for keeping in safe costudy or for reuse or taking credit and making good distrub surface of walls,floor etc complete all as specified and directed by the Engineer- In- Charge. |
| 93 | Supply and fixingwall mounted LEDbatten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,20 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cablefrom ceiling rose to fitting,and testing complete all as specified and directed by the Engineer- In- Charge. Make: Havells cat part No-ENDURALINEARNEOBS20WLED865SPCWH or equivalent in Halonix/Crompton Greaves. |
| 94 | Supply and fixingwall mounted LEDbatten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,10 watt LED fitting with 100 lumen/watt, 6000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cablefrom ceiling rose to fitting,and testing complete all as specified and directed by the Engineer- In- Charge. Make: Havells cat part No-ENDURALINEARNEOBS10WLED865SPCWH or equivalent in Halonix/Crompton Greaves. |
| 95 | Supply and fixing ultra slimsurface decorative 15 watt with 100 lumen/watt, 6000 K ,230 volt, LED ceiling fitting,complete with all accessories , connecting up with twin core twisted flexible copper conductor cablefrom ceiling rose to fitting, and testing complete all as specified and directed by the Engineer-In- Charge.-EDGEPRORDDLR15WLED840S or equivalent inHalonix/Crompton Greaves |
| 96 | Supply and fixing wall mounted LED bulk headfittings, 10 watt, warm white, 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cablefrom ceiling rose to fitting, and testing complete all as specified and directed by the Engineer-In- Charge. |
| 97 | S&F in replacement LED Tube rod 20 watt complete fittings all as specified and directed by Engr-in-charge. |
| 98 | S& F in replacement sub main wiringwith two single core PVC insulated unsheathed cable 1100 volts FRLS grade with multi strand copper conductor and drawn through and includingPVC conduit along with continuous earthing wirebut in green colour complete on surface/concealed of size 2.5 Sqmm ( 2 single runof 2.5 Sqmm and one run of 2.5 Sqmm as earth wire) Note : Three run of PVC cable and one run of PVC conduitshall be measured as one unit length. |
| 99 | (a)All as per item No 95 here in before but 4 Sqmm ( 2 single runof 4 Sqmm and one run of 4 Sqmm as earth wire) |
| 100 | (b) All as per item No 95 here in before but6 Sq.mm ( 2 single run of 6 Sqmm and one run of 6 Sqmm as earth wire) |
| 101 | (c) All as per item No 95 here in before but 10 Sq.mm ( 3 single run of 10 Sqmm and one run of 10 Sqmm as earth wire) |
| 102 | Supply and fix in replacement of new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficient LED as lighting source with toughened glass having IP66 protection with high power120 watt LED , 6000K , with electronic driver, general spread of cat Part No 9405 of make Havells and equivelent make of phillips/CG with all accessories pre-wired and electric connection using PVC insulated and sheathed 1100 volts grade cable with copper conductor of size 2.5 sqmm completewith provn ofnuts and bolts fixing on walls/poles etc. complete all as specified. |
| 103 | S&F in replacement of fan capacitor with copper wire plastic body 2.5 mfd complete all as specified and directed by Engr-in-charge. |
| 104 | S&F in replacement of fan capacitor with copper wire plastic body 3.15 mfd complete all as specified and directed by Engr-in-charge. |
| 105 | S&F in replacement of rubber real for ceiling fan complete all as specified and directed by Engineer in Charge. |
| 106 | S&F in replacement of mild steel U clamps including 10 mm dia but, nuts, washers and split pin for ceiling fan complete all as specified and directed by Engineer in Charge. |
| 107 | S&F of LED ceiling light 34 watt 2x2 recess LED, 6000 K luminaire having glare free symmetrical illumination Complete all as specified and directed by Engineer-in-Charge. |
| 108 | S&F in replacement of ceiling fan heady duty 1200 mm sweep including necessary fixing arrangement for proper fixingas per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 109 | M & L for repair to exhaust fan/ wall mounted fan/ pedestal fan of of any size( 200 to 450 mm sweep) by replacingunserviceable ball bearingNo 6201/6202/6203 including neccessary greasing complete all as specified and directed by Engineer-in-Charge. |
| 110 | S&F in replacement of fan capacitor with copper wire plastic body 1.5 to 2.25 mfd. |
| 111 | S&F in replacement of exhaust fan PVC heavy duty non metalic300 mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 112 | S&F in replacement of PVC exhaust fan non metallic type 230-250mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 113 | S&F in replacement of exhaust fan heavy duty metal body type 230 mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Supply& fix in replacement of wall mounting fan heavy duty 300/380 mm sweep complete all as specified and as directed by Engineer-in-Charge. |
| 115 | S&F in replacement of exhaust fan heavy duty plastic body 200 mm sweep including necessary fixing arrangement for proper fixing in wall and making hole as per site requirement complete all as specified and as directed by Engineer-in-Charge. |
| 116 | Supply and fixing in replacement load line vertical distribution board \"A, frame made out of CRCA 2mm thick mild steel sheet,double door, surface mounting TPN 8 way 415 volts 200 Amps rated bus bar and stove enamels dust and vermin proof suitable forTP/FP \"A\" frame MCCB of 125 Amps =01 No MCBfor outgoing comlete all as specified and as directed by Engineer-in-Charge.Note :- MCB shall be measured and paid seperately. |
| 117 | Supply and fixingin replacement MCB distribution board with Bus bar 200A neutral link , earth bar made out of CRCAmild steel sheet surface mounting SPN 8 way 230 volts double door type regal gray horizontal type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately. |
| 118 | S&F in replacement of MCCB 125 Amps 415 volts 3 phase 50 HZ with Adjustable Thermal & adjustable Magnetic setting of rapturing capacity 25 KA. |
| 119 | Taking down old unsv SP/SPN MCBof any size. |
| 120 | S&F MCB SP 6 to 32 Amps 10 KA, 240 volt \"C\" Series all as specified and directed by Engineer-in-charge. |
| 121 | Fixing onlyMCB SPN32/40 Amps 10 KA, 240 volt50 HZrecieved from Sr item No 33 all as specified and directed by Engineer-in-charge. |
| 122 | Supply and fix in replacement of flexible wire twin core 23/.076 approx 90 mtr per roll complete all as specified and as directed by Engr-in- Charge. |
| 123 | Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 1.5 sqmm 90 mtr per roll complete all as specified and as directed by Engineer in Charge. |
| 124 | Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 2.5 sqmm 90 mtr per roll complete all as specified and as directed by Engineer-in- charge. |
| 125 | Supply & fix in replacement PVC FRLS Flexible cable copper conductor, unsheathed , 1100 volts grade confirming to IS:694/1990 of size 4.0 sqmm90 mtr per roll complete all as specified and as directed by Engineer-in- charge. |
| 126 | Supply and fix in replacement of twin core aluminium flexible wire conductor of size 6 sq mm 2 core complete all as specified and as directed by Engr-in- Charge. |
| 127 | Supply and fix in replacement of twin core aluminium flexible wire conductor of size 10 sq mm 2 core complete all as specified and as directed by Engr-in- Charge. |
| 128 | Excavation in trenches in soft soil n exc 1.5 mtr wide and n.exc 1.5 mtr in depth for laying of pipe,foundation for poles, stay, laying cables etc and getting out copmlete all as directed by engineer-in-charge. |
| 129 | Returning filling in including spreading, leveling watering and well ramming in layers n. exc 25 cm in hard/dense soil copmlete all as directed by engineer-in-charge.. |
| 130 | Removing excavated material n.exc 50 meters and depositing where directed at a level n.exc 1.5 meter above the starting point copmlete all as directed by engineer-in-charge. |
| 131 | M&L for Sand cushioning of cables provided with a layer of sand 8 cm deep before laying the cable and 15 cm depth after punning down and stretching the cable copmlete all as directed by engineer-in-charge. |
| 132 | Supply and layingwell burnt sub class ‘B’ bricks old size as mechanicalprotection to under ground cables laying across the cable copmlete all as directed by engineer-in-charge. |
| 133 | Supply and laying GI pipe light grade galvanizedwith all fittings laid in trenches or fix on wall for cable protection of 50 mm bore coomplete all as specified and directed by engineer-in-charge. |
| 134 | Disconnecting,removing & taking out faulty U/G cable off any sizes from trenches,wall and ducts complete all specified and as directed |
| 135 | Supply, Laying, Testing and connecting cable XLPE insulated armoured heavy duty electric cable with stranded aluminium conductor 1100 volts grade cross section area of 50 sqmm x 3.5 core copmlete all as directed by engineer-in-charge. |
| 136 | All as per srl item No 133 above but size 35 Sq mm x 3.5 core copmlete all as directed by engineer-in-charge. |
| 137 | Supply and fixing in replacement of aluminium thimble stud type suitable for size of cable 240 and above sq mm all as specified and directed by engineer-in-charge. |
| 138 | Supply and fixing in replacement of aluminium thimble stud type suitable for size of cable 35 sq mm to 180sq mmall as specified and directed by engineer-in-charge. |
| 139 | Material and labour for cuttingof road/ hard standing up to a size not exceeding 20cm widthand not exceeding 60cm in depth for laying ofcable protection pipe including making good the disturbed road/hard standing by providing PCC (1:2:4) type B1 and block top with black bituminous upto existing surface level complete all as specified and as directed by Engineer-in-charge. |
| 140 | M&L forearthing complete with GI earth plate electrode 60cmx60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25 meter deep below normal ground level) with top edge of the plate not less than 1.5 meter below normal ground level, connected togalvanized earth lead wire4 mm dia by means of GI bolts, nuts, check nuts and washers earth pit surrounded by picked layer of coal dust and 15 mm thick mixture in equal ratio of magnesium sulphate& copper sulphate in all around bottom and top and watering pipe 20mm bore of GI medium grade with funnel all as shown in electrical plateNO 5 of SSR Part I (1991)and connecting to earthing test point, including CI cover, frame and PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in earthing pit with CI cover and framing including necessary earth work etc, complete all asspecifiedNote :- PCC chamber shall be constructed at least one meter away from building shall be provided in slanting manner. Note:- PCC pit cover shall be precast of RCC 1:2:4 type B-I 80 mm thick reinforced with XPM weighting not less than 4 Kg (sqm in liew of CI) |
| 141 | All as per item No 138 here in beforebut using galvanised iron strip 25x4mm as earthhing lead |
| 142 | S & F in repair 4mm dia GI wire complete all as specified and directe by Engr-in-charge. |
| 143 | Material and labour for galvanisediron strip 25 X 4 mm with saddles and fixing screws and connected as per site requirement comlete all as specified and as directed by Engineer-in-Charge. |
| 144 | Supply & fix in replacement LED bulb 12 Watt pin type warm whiteofall as specified and directed by Engineer in charge. |
| 145 | Supply & fix in replacement LED bulb 12 W screw type warm whitewarm whiteall as specified and directed by Engineer in charge. |
| 146 | M& L for Fabricate, supply and install cubicle type, CPRI approved LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with selflocking arrangment made out of MS angle iron frame work, MS flat iron and CRCA sheet of 3.15 mm thick as per IS 5039 duly painted with powder coated paint of approved shade. The panel shall be suitable for 415 volts,50 Hz, 3 phase 4 wire system and shall be complete with 300 amp capacity copper bus bar,wiring the panel board with suitable size of PVC insulated, multi stranded copper cables and all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etcincluding supply and fixingfollowing acessories:- INCOMING :-(a) MCCB 320 Amps, 4 pole,36 KA DPX3 630 cat No 422006- 1 Nomake Legrand and equvilent make of Simens/Schinder (b) Digital type volt meter - set 01(c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01(d) LED type indicator lamp set of red , yellow and blue- set 01OUT GOING (a)MCCB 200 Amps, 4 pole, 36 KA DPX3 250 cat No 420248- 03 Nos(b)MCCB 125 Amps, 4 pole, 25 KA DPX3 160 cat No 422006 - 02 NosFoundation-(i) Plateform for the panelwith PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation brick work in 1:6 with sub class\"B\" old size bricks sith sandering 15mm in CM1:6of exposed surface and 100mmthick PCC padding 1:3:6 type C-1 using 20mm graded crushed stomneaggregate on top plate form shall be such that it is of a height 45cm above nearest road level. |
