Purvanchal Vidyut Vitaran Nigam Limited has published Tender For Construction Of 33 Kv Line Under Edc Kushinagar. Submission Date for this Tender is 09-04-2024. Transmission Line Tenders in kushinagar Uttar Pradesh. Bidders can get complete Tender details and download the document.
Sl. No. | Item Description |
1 | Work No-1 Part A (Materials Provided by contractor) |
2 | 33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor |
3 | 33 KV ‘XLPE’ C/J Kit 3x300mm ST. through |
4 | Number Plate |
5 | Danger Board with Clamp |
6 | Barbed wire |
7 | Bolts, Nuts, & Washers |
8 | 33 KV Polymer Pin Insulator |
9 | Polymer 33 KV Disc Insulator 70 KN |
10 | Disc fitting B&S Type |
11 | Top Channel 125X65X3200 mm with clamps |
12 | 33 KV V type X-arm |
13 | X-arm clamps. |
14 | Stay Clamp for ST/PCC Pole with Nut and Bolt by 50x8 mm MS Flat Iron make. |
15 | Stay Rod 20x1800 mm |
16 | Stay wire 7/8 SWG |
17 | MS Earthing Rod 20x2500 mm |
18 | P.G. Clamp for DOG |
19 | ‘E’ Bracket for 33 KV |
20 | M.S. Angle Iron 65x65x6mm bracing |
21 | 33 KV M.S. bracing Angle clamp with nut bolt for ST/PCC Pole with nut bolt by 50x8 mm MS flat Iron make |
22 | 33 KV. Top channel (125x65mmX3200 mm (10.7 Kg/m) |
23 | Guarding Channel/Angle 75x40x3010mm |
24 | GI Wire 5 mm 6SWG |
25 | Guarding clamp with Bolt & Nuts |
26 | F Bracket for 33 KV |
27 | Extra angle for cable support |
28 | Clamp for extra angle support |
29 | Al. paint |
30 | Red oxide paint |
31 | PART - B- WORK Shifting, Loading Carriage & Unloading of following materials from store centre Gorakhpur to work site |
32 | 33 KV Line Isolator |
33 | 33 KV Line Isolator Structure |
34 | 33 KV ‘XLPE’ Cable 3x300mm² |
35 | ST Pole 11 M Long |
36 | ACSR Dog Conductor |
37 | PCC Pole 9 M |
38 | MS angle for structure |
39 | Laying of 33 KV 3x300 mm² ‘XLPE’ cable(D/C) by digging pit & making trench in Proper size (1.2M depth x1.2M wide) below ground level by fixing bricks(4½?) on both side of trench wall and 9? brick work at the centre of the trench along the cable. Fixing brick slab on top after filling sand around both the cable including cost of bricks and sand. as per site requirement HDD mathod can be used. |
40 | Jointing charge of 33 KV ‘XLPE’ C/J Kit 3x300 mm² Outdoor/ St. through |
41 | Laying of 33 KV ‘XLPE’ cable in air after providing 6” dia.M.S. pipe 3m long Complete work. |
42 | Special Pipe earthing for 33 KV Jointing Kit. |
43 | Extension of 11 mtr ST pole to 13 mtr all materials with work provided by contractor |
44 | Labour charges for rising of cable through MS Pipe and jumpering with complete work. |
45 | Erection of Single pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (‘V" type cross arm 100 x 50 x 6 mm, clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, barbed wire earthing, etc. complete). |
46 | Erection of Double pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete). |
47 | Erection of Four pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete). |
48 | Erection of Double pole structure on 9 mtr PCC Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete) . |
49 | Erection of Single pole structure on 11mtr ST. (SP-55) Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories ( "V" type cross arm 100 x 50 x 6 mm, clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete). |
50 | Erection of Double pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) . |
51 | Erection of Double pole structure on 11 mtr ST Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) . |
52 | Erection of Four pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) . |
53 | Grouting of stay rods (20 x 1800) mm including all work of excavation, cement concrete in size (0.60 x 0.60 x 0.30) m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg including back filling, proper ramming etc. Fixing tightening &nozzling of stay wire with stay rod with the poles of required tension. |
54 | Chopping of branches of trees of eucalyptus, Neem, Keekar and other kind of trees along the route of the line and disposal of the same at suitable place. (Including existing line) |
55 | Guarding between two poles like single poles, double poles, four poles, etc. to guard LT, 11 KV Line telephone and river crossing, road crossing etc. with G.I. wire no. 6 SWG and G.I. wire no. 8 SWG, cutting, fabrication and fixing of guarding channel 75 x 40 x 3010 mm with clamps nut & bolts etc. |
56 | Erection of Line Isolator Structure and install Line Isolator and earthing complete work. |
57 | Work No-2 Part A (Materials Provided by contractor) |
58 | 33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor |
59 | 33 KV ‘XLPE’ C/J Kit 3x300mm ST. through |
60 | Alluminium Paint |
61 | Red Oxide Paint |
62 | Bolts, Nuts, & Washers |
63 | M.S. Angle Iron 65x65x6mm bracing with clamps |
64 | Top Channel 125X65X3200 mm with clamps |
65 | Polymer 33 KV Disc Insulator 70 KN |
66 | Disc fitting B&S Type |
67 | Polymer 33 KV Pin Insulator |
68 | P.G. Clamp for ‘Dog’ |
69 | ‘E’ Bracket for 33 KV |
70 | Stay Rod 33KV , 20*1800mm |
71 | Stay Clamp 33KV |
72 | Stay wire 7/8 SWG |
73 | G.I. Wire 5mm 6SWG |
74 | Extra angle for cable support |
75 | Clamp for extra angle support |
76 | PART - B- WORK Shifting, Loading Carriage & Unloading of following materials from store centre Gorakhpur to work site |
77 | ST Pole 11 M Long |
78 | STP Pole 9 M |
79 | 33 KV ‘XLPE’ Cable 3x300mm² |
80 | ACSR Dog Conductor |
81 | Laying of 33 KV 3x300 mm² ‘XLPE’ cable by digging pit & making soil trench in Proper size(1M depth x1M wide) below ground level by fixing bricks(4½?) on both side of trench wall and 9? brickat the centre of the trench along the cable.Fixing brick slab on top after filling sand around both the cable including cost of bricks and sand. (as per site requirement HDD mathod can be use). |
82 | Jointing charge of 33 KV ‘XLPE’ C/J Kit 3x300 mm² Outdoor /Straight Through |
83 | Rising of 33 KV ‘XLPE’ cable in air after providing 6” dia.M.S. pipe 3m long Complete work. |
84 | Labour charges for inserting of MS Pipe, Rising of 33 KV cable and jumperingcomplete work. |
85 | Special Pipe earthing for 33 KVJointing Kit. |
86 | cost for laying of 3x300 mm² ‘XLPE’ cable with HDPE Pipe for passing of 33 KV Cableunder road Crossingin the path of Laying of cable.(HDPE pipe & all related materialswith work provided by contractor) |
87 | Erection of Single pole structure on 11mtr ST. (SP-55) Pole for converting S/P to D/Pincluding all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, bolt and nut, composite polymer pin insulator,Polymer Disc Insulator with fitting,danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete). |
88 | Erection of Double pole structure on 9 mtr ST Polefor only cable rising including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) . |
89 | Erection of Double pole structure on 11 mtr ST Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) . |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail