|
| 1 | Equipment & setup required for Electrical Machines I lab. |
| 2 | a. Study of the characteristics of a compound D.C generator (short shunt) [See annexure-1A for detail specification] |
| 3 | b. Measurement of the speed of a D.C series motor as a function of load torque [See annexure-1B for detail specification] |
| 4 | c. Polarity test on a Single- Phase Transformer [See annexure-1C for detail specification] |
| 5 | d. Study of parallel operation of single-phase transformer. [See annexure-1D for detail specification] |
| 6 | e. Determination of temperature rise and efficiency of the transformer (back to back test) [See annexure-1E for detail specification] |
| 7 | f. Study of three-phase transformer connections.[See annexure-1F for detail specification] |
| 8 | Equipment & setup required for Electrical Machines II lab. |
| 9 | a. Different method of starting of 3- Phase Sq. cage induction motor & their comparison (DOL starter, Star-Delta Starter, Auto transformer Starter). [See annexure-2A for detail specification] |
| 10 | b. Study of Performance of Wound Rotor Induction Motor under load. [See annexure-2B for detail specification] |
| 11 | c.Determination of iron loss, friction loss and windage loss of 3-phase induction motor [See annexure-2C for detail specification] |
| 12 | d. Speed control of three phase slip ring Induction motor by rotor resistance control. [See annexure-2D for detail specification] |
| 13 | e. Determination of regulation of synchronous machine by (i) Potierreactance method.(ii) Synchronous Impedance method.[See annexure-2E for detail specification] |
| 14 | f. Determination of equivalent circuit parameters of a single phase Induction motor. [See annexure-2F for detail specification] |
| 15 | g. Load test on single phase Induction motor to obtain the performance characteristics. [See annexure-2G for detail specification] |
| 16 | h. To determine the Direct axis reactance (Xd) & Quadrature axis reactance (Xq) of three phase synchronous machine by slip test.[See annexure-2H for detail specification] |
| 17 | i. Parallel operation of 3 phase Synchronous generators.[See annexure-2I for detail specification] |
| 18 | j. V-curve of Synchronous motor.[See annexure-2J for detail specification] |
| 19 | k. Load test on wound rotor induction motor to obtain the performance characteristics. [See annexure-2K for detail specification] |
| 20 | l. To make a connection diagram of a full pitch & fractional slot winding of an 18 slot Sq. cage induction motor for 6 pole and 4 pole operation. [See annexure-2L for detail specification] |
| 21 | m. To study the performance of the Induction generator.[See annexure-2M for detail specification] |
| 22 | Equipment & setup required for Power System I lab |
| 23 | a. Study of distribution system by DC network analyzer[See annexure-3A for detail specification] |
| 24 | b. Measurement of earth resistance by earth tester [See annexure-3B for detail specification] |
| 25 | c. Determination of dielectric strength ofinsulating oil.[See annexure-3C for detail specification] |
| 26 | d. Determination of breakdown strength of solid insulating material[See annexure-3D for detail specification] |
| 27 | e.Study of active and reactive power control of alternator.[See annexure-3E for detail specification] |
| 28 | f. Determination of dielectric constant, tan delta, resistivity of transformer oil.[See annexure-3F for detail specification] |
| 29 | Equipment & setup required for Power System II lab. |
| 30 | a.Study on the characteristics of on load time delay relay and off load time delay relay [See annexure-4A for detail specification] |
| 31 | b. Test to find out polarity, ratio and magnetization characteristics of CT and PT [See annexure-4B for detail specification] |
| 32 | c. Test to find out characteristics of (a) under voltage relay (b) earth fault relay [See annexure-4C for detail specification] |
| 33 | d. Study of different characteristics of over current relay.[See annexure-4D for detail specification] |
| 34 | Equipment & setup required for Control System lab. |
| 35 | a. Linear System Simulator [See annexure-5A for detail specification] |
| 36 | Equipment & setup required for Power Electronics lab. |
| 37 | a. Study of different triggering circuits of an SCR[See annexure-6A for detail specification] |
| 38 | b. Study of performance of PWM bridge inverter using MOSFET as switch with R and R-L load [See annexure-6B for detail specification] |
| 39 | c. Study of firing circuits suitable for triggering SCR in a single phase full controlled bridge [See annexure-6C for detail specification] |
| 40 | d.Study of the operation of a single phase full controlled bridge converter with R and R-L load [See annexure-6D for detail specification] |
| 41 | e.Study of performance of single phase half controlled symmetrical and asymmetrical bridge converters.[See annexure-6E for detail specification] |
| 42 | f. Study of performance of step down chopper with R and R-L load with Digital display. [See annexure-6F for detail specification] |
| 43 | g. Study of the characteristics of an SCR.V-I characteristics with digital 3 nos meters [See annexure-6G for detail specification] |
| 44 | h. Study of the characteristics of a Triac.V-I characteristics with digital meters. [See annexure-6H for detail specification] |
| 45 | Equipment & setup required for Electrical Design lab. |
| 46 | a. Design a controller for speed control ofDC Machine [See annexure-7A for detail specification] |
| 47 | b. Design a heating element with specified wattage, voltage and ambient temperature.[See annexure-7B for detail specification] |
| 48 | c. Familiarization of construction of single phase Fan |
| 49 | d. Design and fabrication of small single phase transformer, 100VA, 220/12 V [See annexure-7C for detail specification] |
| 50 | e. Hand held LCR meter – 3 nos[See annexure-7Dfor detail specification] |
| 51 | f. AC/DC Clamp Meter- 3nos[See annexure-7E for detail specification] |
| 52 | g. Megger- 3 nos. |
| 53 | Equipment & setup required for Electrical Drives lab. |
| 54 | a. Study of speed control of Chopper fed DC Drive [See annexure-8A for detail specification] |
| 55 | b. Study of speed control of single phase motor using TRIAC & DIAC. [See annexure-8B for detail specification] |
| 56 | c. Study of V/f control of 3phase Induction motor drive[See annexure-8C for detail specification] |
| 57 | d. Study of speed control of Thysistorcontrolled DC Drive [See annexure-8D for detail specification] |
| 58 | e. Study of PC/PLC based AC/DC motor control operation[See annexure-8E for detail specification] |
