Tender For Addition / Alteration To Bldg No C-1 ( Type-Iii Qtrs ) At Nrml Ambernath; 1 Dismantling Tile Work In Floors And Roofs Laid In Cement Mortar Including Stacking Material Within 50 Metres Lead For Thickness Of Tiles 10 Mm To 25 Mm Complete All As Specified And Directed. 2 Dismantling Dado / Skirting Raking Out Joints And Cleaning The Surface For Plaster Including Disposal Of Rubbish To The Dumping Ground Within 50 Metres Lead Complete All As Specified And Directed. 3 Demolishing Cement Concrete Nominal Concrete 1:4:8 Or Leaner Mix Manually / By Mechanical Means Including Disposal Of Material Within 50 Metres Lead Complete All As Specified And Directed By Engineer - In - Charge. 4 Cement Concrete1:2:4, Using 40Mm Thick With 20Mm Nominal Size Stone Aggregate In Flooringfinished With A Floating Coat Of Neat Cement, Including Cement Slurry, But Excluding The Cost Of Nosing Of Steps Etc. Complete All As Specified And Directed. 5 Providing And Laying Vitrified Floor Tiles 600X600 Mm In Different Sizes ( Thickness Not Less Than 9 Mm ) And Conforming To Is: 15622, Of Approved Make, In All Colours And Shades, Laid On 20Mm Thick Cement Mortar 1:4, Jointing With Grey Cement Slurry @ 3.3 Kg / Sqm Including Grouting The Joints With White Cement And Matching Pigments Etc., Complete All As Specified And Directed. 6 Providing And Laying Vitrified Tiles 600X600 Mm In Different Sizes ( Thickness Not Less Than 9Mm ) And Conforming To I.S. 15622, Of Approved Make, In All Colours & Shades, Laid On 12Mm Thick Cement Mortar1:3, Jointing With Grey Cement Slurry @ 3.3 Kg / Sqm Including Grouting The Joint With White Cement & Matching Pigments Etc. Complete All As Specified And Directed. 7 Providing And Laying Glazed Vitrified Tiles Matt / Antiskid Finish Of Size 300 X 300 Mm In Floor In Different Sizes ( Thickness Not Less Than 7 Mm And Conforming To Is:15622, Of Approved Brand & Manufacturer, In All Colours And Shade, Laid On 20 Mm Thick Cement Mortar 1:4Jointing With Grey Cement Slurry @3.3 Kg / Sqm Including Grouting The Joints With White Cement And Matching Pigments Etc. The Tiles Must Be Cut With The Zero Chipping Diamond Cutter Only . Laying Of Tiles Will Be Done With The Notch Trowel, Plier, Wedge, Clips Of Required Thickness, Leveling System And Rubber Mallet For Placing The Tiles Gently And Easily Complete All As Specified And Directed. 8 Providing And Fixing 1St Quality Ceramic Glazed Wall Tiles Conforming To Is: 15622 ( Thickness Not Less Than 7 Mm, Of Approved Make, In All Colours, Shades Except Burgundy, Bottle Green, Black Of Any Size As Approved By Engineer-In-Charge, In Skirting, Risers Of Steps And Dados, Over 12 Mm Thick Bed Of Cement Mortar 1:3And Jointing With Grey Cement Slurry @ 3.3Kg Per Sqm, Including Pointing In White Cement Mixed With Pigment Of Matching Shade Complete All As Specified And Directed. 9 Dismantling Stone Slab Flooring Laid In Cement Mortar Including Stacking Of Serviceable Material And Disposal Of Unserviceable Material Within 50 Metres Lead Complete All As Specified And Directed. 10 Providing And Fixing 18 Mm Thick Granite Stone Slab Colour Black Area Of Slab Upto 0.50 Sqm Gang Saw Cut, Mirror Polished, Premoulded And Prepolished, Machine Cut For Kitchen Platforms, Vanity Counters, Window Sills, Facias And Similar Locations Of Required Size, Approved Shade, Colour And Texture Laid Over 20 Mm Thick Base Cement Mortar 1:4, Joints Treated With White Cement, Mixed With Matching Pigment, Epoxy Touch Ups, Including Rubbing, Curing, Moulding , Rounding To Edges And Polishing To Edges To Give High Gloss Finish Etc. Complete All As Specified And Directed. 11 Material And Labour For 15 Mm Thick Cement Plaster On The Rough Side Of Single Or Half Brick Wall With Cm 1:4Complete All As Specified And Directed. 12 Providing & Applying Polymer Modified, Flexible Cementatious Negative Side Waterproofing Coating With Elastic Waterproofing Polymers On Interior Wall Plaster Surface In Three Coats @14.35 Kg / 10 Sqm. One Coat Of Self Priming Of Cementatious Waterproofing Polymer ( Dilution With Water In The Ratio Of 1:1 ) And Two Coats Of Cementatious Waterproofing Polymer ( Dilution With Water In The Ratio Of 3:1 ) After Scrapping And Properly Cleaning The Surface To Remove Pre-Existing Paint Film & Loose Particles Till Plaster Is Visible, Complete All As Specified And Directed By Engineer-In-Charge. 13 Providing And Laying In Position Cement Concrete Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level :1:4:8 ( Using Stone Aggregate 40 Mm Nominal Size ) Complete All As Specified And Directed. 14 Dismantling Doors, Windows And Clerestory Windows ( Steel Or Wood Or Pvc ) Shutter Of Area 3 Sq. Metres And Below Including Chowkhats, Architrave, Holdfasts Etc. Complete And Stacking Within 50 Metres Lead Complete All As Specified And Directed. 15 Providing And Fixing Pvc Door Frame Of Size 50X47 Mm With A Wall Thickness Of 5 Mm ( ± 0.2 Mm ) , Made Out Of Single Piece Extruded Pvc Profile, With Mitred Cut Joints And Joint With 2 Nos Of Pvc Bracket Of Size 190 Mm X 100 Mm Long Arms Of Cross Section Size 35 X 15 Mm & Self Driven Self Taping Screws, The Vertical Door Profiles To Be Reinforced With 40X20 Mm M.S. Rectangular Tube Of 0.8 Mm , Including Providing Epdm Rubber Gasket Weather Seal Throughout The Frame, Including Jointing 5 Mm Pvc Frame Strip With Pvc Solvent Cement On The Back Of The Profile. The Door Frame To Be Fixed To The Wall Using 8 X100 Mm Long Anchor Fasteners Complete, All As Per ManufacturerS Specification And Complete All As Specified And Directed By Engineer -In- Charge. 16 Non Decorative Finish ( Matt Finish ) 35 Mm Thick Factory Made Solid Panel Pvc Door Shutter, Made Out Of Single Piece Extruded Soild Pvc Profiles, 5 Mm ( ± 0.2 Mm ) Thick, Having Styles & Rails ( Except Lock Rail ) Of Size 95 Mmx 35 Mm X 5 Mm, Out Of Which 75 Mm Shall Be Flat And 20 Mm Shall Be Tapered ( On Both Side ) , Having One Side Thickness Of 15 Mm Integrally Extruded On The Hinge Side Of The Profile For Better Screw Holding Power, Including Reinforcing With Ms Tube Of Size 40 Mm X 20 Mm X 1 Mm, Joints Of Styles & Rails To Be Mitered Cut & Joint With The Help Of Pvc Solvent Cement, Self Driven Self Tapping Screws & M.S. Rectangular Pipes Bracket Of Size 190 Mm X 100 Mm Of Cross Section Size 35 Mm X 17 Mm X 1 Mm At Each Corner. Single Piece Extruded 5 Mm Thick Solid Pvc Lock Rail Of Size 115 Mm X 35 Mm, Out Of Which 75 Mm To Be Flat And 20 Mm To Be Tapered At Both Ends, Having 15 Mm Solid Core In Middle Of Rail Section Integrally Extruded, Fixing The Styles & Rails With The Help Of Solvent And Self Driven Self Tapping Screws Of 125 Mm X 11 Mm, Including Providing 5 Mm Single Piece Solid Pvc Extruded Sheet Inserted In The Door As Panel, As Per ManufacturerS Complete All As Specified And Directed Of Engineer-In-Charge. 17 Providing Second Class Teakwood Work In Frames Of Doors, Windows, Clerestory Windows And Other Frames, Wrought Framed And Fixed In Position With Hold Fast Lugs Or With Dash Fasteners Of Required Dia & Length ( Hold Fast Lugs Or Dash Fastener Shall Be Paid For Separately ) Complete All As Specified And Directed. 18 Providing And Fixing 30 Mm Thickflush Door Shutters Conforming To Is : 2202 ( Part I ) Non-Decorative Type, Core Of Block Board Construction With Frame Of 1St Class Hard Wood And Well Matched Commercial 3 Ply Veneering With Vertical Grains Or Cross Bands And Face Veneers On Both Faces Of Shutters Including Isi Marked Stainless Steel Butt Hinges Of Suitable Size With Necessary Screws Complete All As Specified And Directed. 19 Providing And Fixing Second Class Teak Wood 30 Mm Thick Wire Gauge Shutters With Isi Marked M.S. Pressed Butt Hinges Bright Finished Of Required Size Using Galvanized M.S. Wire Gauge Of Average Width Of Aperture 1.4 Mm In Both Directions With Wire Of Dia 0.63 Mm, For Doors, Windows And Clerestory Windows With Hinges And Necessary Screws Complete All As Specified And Directed. 20 Providing And Laying In Position Cement Concrete For Hold Fast Of Specified Grade Excluding The Cost Of Centering And Shuttering - All Work Up To Plinth Level : 1:2:4 Type B1 ( Using 20 Mm Graded Stone Aggregate ) Including Manufactured Sand Complete All As Specified And Directed. 21 Providing And Fixing100x75x3.50 Mmisi Marked, Is : 1341, M.S. Butt Hinges With Necessary Screws Etc. Complete All As Specified And Directed. 22 Providing And Fixing 300X16 Mmaluminium Sliding Door Bolts, Isi Marked Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) , Transparent Or Dyed To Required Colour Or Shade, With Nuts And Screws Etc. Complete All As Specified And Directed. 23 Providing And Fixing125 Mm Aluminium Handles, Isi Marked, Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete All As Specified And Directed. 24 Providing And Fixing 200X10 Mmaluminium Tower Bolts, Isi Marked, Anodised ( Anodic Coating Not Less Than Grade Ac 10 As Per Is : 1868 ) Transparent Or Dyed To Required Colour Or Shade, With Necessary Screws Etc. Complete All As Specified And Directed. 25 Providing And Fixing Bright Finished Brass Hanging Type Floor Door Stopper With Necessary Screws, Etc. Complete All As Specified And Directed. 26 Providing And Fixing 150 Mm Oxidised M.S. Hasp And Staple ( Safety Type ) Conforming To Is : 363 With Necessary Screws Etc. Complete All As Specified And Directed. 27 Providing And Fixing Powder Coated Aluminium Frame ( Minimum Thickness Of Powder Coating 50 Micron ) Work For Doors, Windows, Ventilators And Partitions With Extruded Built Up Standard Tubular Sections / Appropriate Z Sections And Other Sections Of Approved Make Conforming To Is: 733 And Is: 1285, Fixing With Dash Fasteners Of Required Dia And Size, Including Necessary Filling Up The Gaps At Junctions, I.E. At Top, Bottom And Sides With Required Epdm Rubber / Neoprene Gasket Etc. Aluminium Sections Shall Be Smooth, Rust Free, Straight, Mitred And Jointed Mechanically Wherever Required Including Cleat Angle, Aluminium Snap Beading For Glazing / Paneling, C.P. Brass / Stainless Steel Screws, All Complete As Per Architectural Drawings And Complete All As Specified And Directed Of Engineer-In-Charge. ( Glazing, Paneling And Dash Fastenersto Be Paid For Separately ) 28 Providing And Fixingpowder Coated Aluminium ( Minimum Thickness Of Powder Coating 50 Micron ) Work Forsiliding Shutters Of Doors, Windows & Ventilators Including Providing And Fixing Hinges / Pivots And Making Provision For Fixing Of Fittings Wherever Required Including The Cost Of Epdm Rubber / Neoprene Gasket Required ( Fittings Shall Be Paid For Separately ) Ventilators And Partitionscomplete All As Specified And Directed By Engineer-In-Charge. ( Glazing, Paneling And Dash Fasteners To Be Paid For Separately ) 29 Providing And Fixing Glazing In Aluminium Door, Window, Ventilator Shutters And Partitions Etc With Float Glass Panes Of 4.0 Mm Thickness ( Weight Not Less Than 10Kg / Sqm ) With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Directions Of Engineer-In-Charge . ( Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item ) 30 Providing And Fixing Fly Proof Stainless Steel With Aluminium Beading Grade 304 Wire Gauge, To Windows And Clerestory Windows Using Wire Gauge With Average Width Of Aperture 1.4 Mm In Both Directions With Wire Of Dia. 0.50 Mm All Complete All As Specified And Directed. 31 Providing And Fixing Glazing In Aluminium Door, Window, Ventilator Shutters And Partitions Etc With Frosted Glass Panes Of 4.0 Mm Thickness ( Weight Not Less Than 10Kg / Sqm ) With Epdm Rubber / Neoprene Gasket Etc. Complete As Per The Directions Of Engineer-In-Charge . ( Cost Of Aluminium Snap Beading Shall Be Paid In Basic Item ) 32 Dismantling Old Plaster Or Skirting Raking Out Joints And Cleaning The Surface For Plaster Including Disposal Of Rubbish To The Dumping Ground Within 50 Metres Lead Complete All As Specified And Directed. 33 Material And Labour For 15Mm Thick External Wall Plaster On Brick Or Concrete Surfacesin Cm 1:4Shall Be Provided In Two Coats Viz 10 Mm First Coat And 5 Mm Second Coat Using W.P.C.And Finished Fair And Even Complete All As Specified And Directed.Note:- Wpc Will Measurement Separately. 34 Material And Labour For 12 Mm Thick Internal Plaster On Brick Or Concrete Surfaces In Cm 1:6 Andfinished Even & Smooth Without Using Extra Cement Complete All As Specified And Directed. 35 Material And Labour For 6 Mm Cement Plaster In 1:3 Finished With A Floating Coat Of Neat Cement And Thick Coat Of Lime Wash On Top Of Walls When Dry For Bearing Of R.C.C. Slabs And Beams Complete All As Specified And Directed. 36 Supply Only Water Proofing Liquid Complete All As Specified And Directed. 37 Preparation Of Newly Plastered Surfaces And Apply Primer Coat Of Wall Andapplying Two Coats Of Distempering With 1St Quality Acrylic Distemper ( Ready Mixed ) Having Voc Content Less Than 50 Gms / Litre, Of Approved Manufacturer, Of Required Shade And Colour Complete, As Per ManufacturerS Specification Over A Coat Of Primer All As Specified And Directed. 38 Preparing New Plastered Surfaceand Apply Primer Coat Of Wall And Applyingtwo Coats Of Exterior Emulsion Paint Over A Coat Of Primer Complete All As Specified And Directed. 39 Material And Labour For Preparation Of Newly Plastered Ceiling And Applying Three Coats Of White Wash Complete All As Specified And Directed. 40 Removing Dry Or Oil Bound Distemper, Water Proofing Cement Paint And The Like By Scrapping, Sand Papering And Preparing The Surface Smooth Including Necessary Repairs To Scratches Etc. Complete All As Specified And Directed. 41 Preparation Of Old Plastered Surfaces And Apply Primer Coat Of Wall And Applying 2 Coats Of Wall Painting With Premium Acrylic Emulsion Paint Of Interior Grade, Having Voc ( Volatile Organic Compound ) Content Less Than 50 Grams / Litre Of Approved Brand And Manufacture, Complete All As Specified And Directed. 42 Removing White Or Colour Wash By Scrapping And Sand Papering Andpreparing The Surface Smooth Including Necessary Repairs Andproviding And Applying Plaster Of Paris Putty Of 2 Mm Thickness Over Plastered Surface To Prepare The Surface Even And Smoothand Apply Two Coat Of Distempering With 1St Quality Acrylic Distember ( Ready Mix ) Having Voc Content Less Than 50 Grams / Litre Of Approved Brand And Manufacture To Give An Even Shade Complete All As Specified And Directed. 43 Material And Labour For Two Coat Of White Wash On Ceiling Including Preparation Of Old Surfaces Complete All As Specified And Directed. 44 Painting With Synthetic Enamel Paint On Steel Surface Of Approved Brand And Manufacture Of Required Colour To Give An Even Shadetwo Coats Onnew Work Complete All As Specified And Directed. 45 Finishing With Deluxe Multi Surface Paint System For Interiors And Exteriors Using Primer As Per Manufacturers Specifications Painting Wood Work With Deluxe Multi Surface Paint Of Required Shade. Two Coats Applied @ 0.90 Ltr / 10 Sqm Over An Under Coat Of Primer Applied @0.75 Ltr / 10 Sqm Of Approved Brand And Manufacture Complete All As Specified And Directed. 46 Applying Priming Coat For New Wood Work With Ready Mixed Pink Or Grey Primer Of Approved Brand And Manufacture On Wood Work ( Hard And Soft Wood ) And Finishing With Deluxe Multi Surface Paint System For Interiors And Exteriors Using Primer Including Painting Wood Work With Deluxe Multi Surface Paint Of Required Shade. Two Coats Applied @ 0.90 Ltr / 10 Sqm Over An Under Coat Of Primer Applied @0.75 Ltr / 10Sqm Of Approved Brand And Manufacture As Per Manufacturers Specifications Complete All As Specified And Directed. 47 Supply And Fix 75 Mm Dia Pvc ( Swr ) Floor Trap With Gratings Including Jointing With Solvent Cement, Including Jointing To Waste Pipe And Fixed Incement Concrete Type B1 1:2:4 Complete All As Specified And Directed. 48 Supply And Fix In Repair On Terrace ( At All Floor Levels ) Polyethylene Water Storage Tank, Is : 12701 Marked, With Cover And Suitable Locking Arrangement And Making Necessary Holes For Inlet, Outlet And Overflow Pipes But Without Fittings And The Base Support For Tank Complete All As Specified And Directed. 49 Providing And Fixing 20 Mm Nominal Bore Ball Valve ( Brass ) Of Approved Quality, High Or Low Pressure, With Plastic Floats Complete All As Specified And Directed. 50 Providing And Fixing Cpvc Gate Valve Of Approved Quality ( Screwed End ) Of 20Mm Dia Bore And Fixed Complete All As Specified And As Directed. 51 Providing And Fixing 610X510 Mm Bowl Depth 200 Mm Kitchen Sink Withoutdrain Board Stainless Steel A Isi 304 ( 18 / 8 ) Kitchen Sink As Per Is:13983 With C.I. Brackets And Stainless Steel Plug 40 Mm, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls Wherever Required Complete All As Specified And Directed. 52 Supply And Fix In Repairs Kitchen Steel Plate Rack Of Size 914 X 914 X 254 Mm Stainless Steel 1.00 Mm Thick Of Standard Quality Complete All As Specified And Directed. 53 Supply And Fix In Repairs Water Closet Squatting Pan ( Indian Type W.C. Pan ) With 100 Mm Sand Cast Iron P Or S Trap, 10 Litre Low Level White P.V.C. Flushing Cistern, Including Flush Pipe, With Manually Controlled Device ( Handle Lever ) Conforming To Is : 7231, With All Fittings And Fixtures Complete, Including Cutting And Making Good The Walls And Floors Wherever Required:White Vitreous China Orissa Pattern W.C. Pan Of Size 680X470 Mm With Integral Type Foot Rests Complete All As Specified And Directed. 54 Providing And Fixing Wash Basin With C.I. Brackets, 15 Mm C.P Pillar Cock, 32 Mm C.P Waste Coupling And Pipe Of Standard Pattern, Including Painting Of Fittings And Brackets, Cutting And Making Good The Walls Wherever Required. White Vitreous China Flat Back Wash Basin Size 550X400 Mm With Single 15 Mm C.P Pillar Cock Complete All As Specified And Directed. 55 Providing And Fixing 600X450 Mm Beveled Edge Mirror Of Superior Glass ( Of Approved Quality ) Complete With 6 Mm Thick Hard Board Ground Fixed To Wooden Cleats With C.P. Brass Screws And Washers Complete All As Specified And Directed. 56 Providing And Fixing 15 Mm Nominal Bore C.P. Brass Stop Cock ( Concealed ) Of Standard Design And Of Approved Make Conforming To Is:8931 Complete All As Specified And Directed. 57 Providing And Fixing Uplasticised Pvc Connection Pipe 45 Cm Length With Brass Unions 15 Mm Nominal Bore Complete All As Specified And Directed. 58 Providing And Fixing C.P. Brass 15 Mm Nominal Borebib Cock Of Approved Quality Conforming To Is:8931 Complete All As Specified And Directed. 59 Providing And Fixing C.P. Brass Shower Rose With 15 Or 20 Mm Inlet :100 Mm Diameter Complete All As Specified And Directed. 60 Providing And Fixing Ptmt Towel Rail Complete With Brackets Fixed To Steel Cleats With Cp Brass Screws With600 Mm Long Towel Rail With Total Length Of 645 Mm, Width 78 Mm And Effective Height Of 88 Mm, Weighing Not Less Than 190 Gms Complete All As Specified And Directed. 61 Dismantling C.I. Or Asbestos Rain Water Pipe With Fittings And Clamps Including Stacking The Material Within 50 Metres Lead :75 To 80 Mm Dia Pipe Complete All As Specified And Directed. 62 Providing And Fixingsingle Socketed Pipes75 Mm Diameter On Wall Face Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, Complete All As Specified And Directed. 63 Providing And Fixingsingle Socketed Pipes110 Mm Diameter On Wall Face Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, Complete All As Specified And Directed. 64 Providing And Fixing75 Mm Bend On Wall Face Unplasticised - Pvc Moulded Fittings / Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion Complete All As Specified And Directed. 65 Providing And Fixing110 Mm Bend On Wall Face Unplasticised - Pvc Moulded Fittings / Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, Complete All As Specified And Directed. 66 Providing And Fixing75 Mm Single Tee With Door On Wall Face Unplasticised - Pvc Moulded Fittings / Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, Complete All As Specified And Directed. 67 Providing And Fixing110 Mm Single Tee With Door On Wall Face Unplasticised - Pvc Moulded Fittings / Accessories For Unplasticised Rigid Pvc Rain Water Pipes Conforming To Is : 13592 Type A, Including Jointing With Seal Ring Conforming To Is : 5382, Leaving 10 Mm Gap For Thermal Expansion, Complete All As Specified And Directed. 68 Supply And Fix Pvc ( Swr ) Vent Cowl 75 Mm Dia Complete All As Specified And Directed. 69 Supply And Fix Pvc ( Swr ) Vent Cowl 110 Mm Dia Complete All As Specified And Directed 70 Dismantling 15 To 40 Mm Dia G.I. Pipe Including Stacking Of Dismantled Pipes ( Within 50 Metres Lead ) Complete All As Specified And Directed By Engineer-In-Charge. 71 Providing And Fixing 15 Mm Nominal Dia Pipeschlorinated Polyvinyl Chloride ( Cpvc ) Pipes Concealed Work, Including Cutting Chases And Making Good The Wall Etc, Having Thermal Stability For Hot & Cold Water Supply, Concealed Work, Including Cutting Chases And Making Good The Walls Etc Including All Cpvc Plain & Brass Threaded Fittings, I / C Fixing The Pipe With Clamps At 1.00 M Spacing. This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement And The Cost Of Cutting Chases And Making Good The Same Including Testing Of Joints Complete All As Specified And Directed By Engineer In Charge. 72 Providing And Fixing For External Work Of 20 Mm Nominal Dia Chlorinated Polyvinyl Chloride ( Cpvc ) Pipes, Having Thermal Stability For Hot & Cold Water Supply Including All Cpvc Plain & Brass Threaded Fittings This Includes Jointing Of Pipes & Fittings With One Step Cpvc Solvent Cement, Trenching, Refilling & Testing Of Joints Complete All As Specified And Directed By Engineer In Charge. 73 Providing And Fixing 15 Mm Nominal Dia Cp Brass Single Lever Telephonic Wall Mixer Of Quality & Make As Approved And Complete All As Specified And Directed By Engineer In Charge. 74 Providing And Fixingmild Steel Cp Of 20Mm External Dia And 1.60 Mm Thick Curtain Rodswith Twobrackets Fixed With Brass Screws And Wooden Plugs Etc. Wherever Necessary Complete All As Specified And Directed. 75 Dismantling Steel Work In Built Up Sections In Angles, Tees, Flats And Channels Including All Gusset Plates, Bolts, Nuts, Cutting Rivets, Welding Etc. Including Dismembering And Stacking Within 50 Metres Lead Complete All As Specified And Directed. 76 Providing And Fixingm.S. Tubehand Rail Of Approved Size By Welding Etc. To Steel Ladder Railing, Balcony Railing, Staircase Railing And Similar Works, Including Applying Priming Coat Of Approved Steel Primer Complete All As Specified And Directed. 77 Providing And Fixing 12 Mm Thick Factory Made Single Extruded Wpc ( Wood Polymer Composite ) Solid Plain White Color Board For Backing Of Cup Boards And Bathroom / Kitchen Cabinets Etc. Of Required Size Comprising Of Virgin Polymer Of K Value 58-60 ( Suspension Grade ) , Calcium Carbonate And Natural Fibers ( Wood Powder / Rice Husk / Wheat Husk ) And Non Toxic Additives ( Maximum Toxicity Index Of 12 For 100 Gms ) Having Minimum Density Of 650 Kg / Cum And Screw Withdrawal Strength Of 1800 N ( Face ) & 900 N ( Edge ) , Minimum Compressive Strength 50 N / Mm2, Modulus Of Elasticity 850 N / Mm2 And Resistance To Spread Of Flame Of Class A Category With Property Of Being Termite / Borer Proof, Water / Moisture Proof And Fire Retardant And Fixing With Stainless Steel Screws Etc. Complete All As Specified And Directed By Engineer-In- Charge. ( Note: Stainless Steel Screws Shall Be Paid Separately ) 78 Material And Labour For Plinth Protection 50Mm Thick Of Cement Concrete 1:3:6 Type C1 ( Using 20 Mm Graded Stone Aggregated ) Over 75Mm Thick Bed Of Dry Brick Ballast 40 Mm Nominal Size, Well Rammed And Consolidated And Grouted With Fine Sand, Including Expansion Joint Every 2M Interewel And Necessary Excavation, Levelling & Dressing & Finishing The Top Smooth Complete All As Specified And Directed. 79 Taking Down Carefully Copper / Aluminum Point Wiring ( Light, Socket Or Power ) Complete And Making Good Disturbed Surfaces Of Walls, Floors, Ceilingsetc Complete All As Specified And Directed And Catered For Schedule Of Credit 80 Taking Down Existing Main Switches, Industrial Plug And Socket & Dbs Along With Mcb / Mccbs Of Any Make, Size And Complete All As Specified And Directed 81 Taking Down And Refixing, Testing And Commissioning Of Ceiling Fan / Exhaust Fan, Including Wiring The Down Rods Of Standard Length ( Upto 30 Cm ) With 1.5 Sq Mm Frls Pvc Insulated, Copper Conductor, Single Core Cable, Including Providing And Fixing Phenolic Laminated Sheet Cover On The Fan Box Etc. As Requiredcomplete All As Specified And Directed. 82 Painting Of Ceiling Fan / Exhaust Fan With One Coat Of Spray Painting With Syntheic Enamel Paint Of Approved Brand And Manufacture To Give An Even Shade, Including Cleaning Of Surface With Detergent Etc. Complete All As Specified And Directed. 83 Dismantling The Existing Sub Main Wiring / Power Point Wiring Of Any Size And Typecomplete All As Directed. 84 Wiring For Circuit / Submain Wiring Alongwith Earth Wire With The 2 X 4 Sq. Mm + 1 X 4 Sq. Mm Earth Wire Of Frls Pvc Insulated Unsheathed Copper Conductor, Single Core Cable Including Surface / Recessed Medium Class Pvc Conduit As Required Complete All As Specified And Directed. 85 Group A Wiring For Light Point With 1.5 Sq Mm Frls Pvc Insulated Unsheathed Copper Conductor Single Core Cable In Surface / Recessed Medium Class Pvc Conduit, With Modular Swtich, Modular Plate, Suitable Gi Box And Earthing The Point With 1.5 Sq Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc Complete All As Specified And Directed. 86 All As Per Item No 85 Here- In-Before But For Fan Point Complete All As Specified And Directed. 87 All As Per Item No 85 Here-In- Before But For Bell Point Complete All As Specified And Directed. 88 All As Per Item No 85 Here-In- Before Butfor 5 Amp Socket Point On Independent Board Complete All As Specified And Directed. 89 Supplying And Drawing 3 X 2.5 Sq Mm Size Of Frls Pvc Insulated Copper Conductor, Single Core Cables In The Existing Surface / Recessed Steel / Pvc Conduit As Required. Complete All As Specified And Directed. 90 Supplying And Fixing 15 / 16 Amps Modular Switch On Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Requiredall As Specified And Directed. 91 Supplying And Fixing 6 Pin 15 / 16 Amps Modular Socket Outlet On Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Required Complete All As Specified And Directed 92 Supplying And Fixing 3 Pin 5 / 6 Amps Modular Socket Outlet On Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. Complete All As Specified And Directed. 93 Supplying And Fixing Two Module Stepped Type Electronic Fan Regulator On The Exising Modular Plate Switch Box Including Connections But Excluding Modular Pate Etc. Complete All As Specified And Directed. 94 Supply And Fixing Modular Bell Push 2 Way On The Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. Complete All As Specified And Directed. 95 Supply And Fixing Bell Dingdong, 230V, Ac, 50 Hz Complete All As Specified And Directed. 96 Supply And Fixing Basic All Purpose Surface And Wall Mounted Led Batten 20 Watt 4 Feet With Aluminum Housing & Integrated Electronic Driver Including 2 Core Copper Wire From Ceiling Rose To Light Fitting. Complete All As Specified And Directed. 97 Supply And Fixing Basic All Purpose Surface And Wall Mounted Led Batten 10 Watt , 2 Feet With Aluminum Housing & Integrated Electronic Driver Including 2 Core Copper Wire From Ceiling Rose To Light Fitting. Complete All As Specified And Directed. 98 Supply And Fixing Environmental Friendly, Ultra Modern, Energy Saving, Surface Mounted, Decorative Hexagon Bulk Head Back-Lit Led Luminaire Comprising Of High Brightness Leds, 10 Watt, Ip-66 Complete All As Specified And Directed. 99 Supply And Fixing New Generation Energy Saving And Environmental Friendly Long Life Led Street Light 25 Watt Made Up Of Pressure Die Cast Aluminium Housing With High Efficiency Led As Lighting Source And Lens Embedded Pc Cover Having Bottom Opening Seperate Driver Compartment With Ip66 Protection And Impact Resistance Of Ik08 Including Gi Bracket 40 Mm Dia Low Grade, 1.2 Meter Length Bent To Shape Of 120 Degree With Gi Strip Clamp 2 Nos And Nut, Bolts And Washers Complete All As Specified And Directed. 100 Supply And Fixing Round Elegantly Designed Sleek Surface Mounted Pressure Die-Cast Aluminium Luminaire 12 Watts In Powder Coated White Finish In Round Profile With Optimized Heat Sink For Efficient Heat Dissipation And Independent Electronic Led Driver And With 2 Core Copper Wire To Light Fitting Complete All As Specified And Directed. 101 Supply And Fixing 3 Pin 5 A Ceiling Rose On The Existing Junction Box / Wooden Block Including Connections Etc. Complete All As Specified And Directed. 102 Supplying And Fixing 4 Way ( 4 + 12 ) , Double Door, Horizontal Type Three Pole And Neutral, Sheet Steel, Mcb Distribution Board, 415V, On Recess, Complete With Tinned Copper Bus Bar, Neutral Bus Bar, Earth Bar, Din Bar, Interconnections, Powder Painted Including Earthing Etc Complete All As Specified And Directed ( But Without Mcb / Rccb / Isolator ) 103 Supplying And Fixing 63A Rating, Four Pole, 415V, Isolator In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. Complete All As Specified And Directed. 104 Supplying And Fixing 8 Way, Double Door, Single Pole And Neutral, Sheet Steel, Mcb Distribution Board, 240V, On Surface / Recess, Complete With Tinned Copper Bus Bar, Neutal Bus Bar, Earth Bar, Din Bar, Internconnections, Powder Painted Including Earthing Etc.Complete All As Specified And Directed.. ( But Without Mcb / Rccb / Isolator ) 105 Supply And Fixing 5 To 32 Amps Rating , 240 / 415V, 10 Ka C Curve, Miniature Circuit Breaker Suitable For Inductive Load Of Single Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioining Etccomplete All As Specified And Directed. 106 Supply And Fixing 40 Amps Rating, Double Pole, 240 Volts, Isolator In The Existing Mcb Db Complete With Connections, Testing And Commissioining Etccomplete All As Specified And Directed. 107 Material And Labour For Earthing With Galvanised Steel Earth Plate Electrode 600Mm X 600Mm X 6 Mm Thick Buried Directly In Ground Earth Pit Not Less Than 2.25 Metre Deep Below Ground Level With Top Edge Of The Plate Not Less Than 1.5 Metre Below Normal Ground Level Connected To Galvanised Strip Earth Wire 4Mm Dia By Means Of Nuts, Bolts, Check Nuts, Washers Of Galvanised Iron Or Steel All As Shown In Electrical Plate No. 03 Of Ssr Part I Connected To Earthing Test Point Including Excavation / Earth Work In Any Type Of Strata, Removal Of Surplus Excavated Material, Gi Pipe For Watering And Funnel, Pcc 1:3:6 Type C1 Use 20 Mm Graded Stone Aggregate Chamber Including Necessary Formwork / Mould For Fair And Even Surfaces, Precast Rcc 1:2:4 Type B0 Use 12.5 Mm Graded Stone Aggregate Chamber Cover Slab, Gi Funnel, With Gi Watering Pipe 20 Mm Bore Medium Graded, Wire Mesh, Protection Pipe 40 Mm Bore Gi Pipe Light Grade For Earth Lead Upto 7.50 Metre Long Salt, Charcoal Including Testing Complete All As Specified And Directed By Engineer-In-Charge.Note : ( I ) Gi Earth Wire Beyond 7.5 Metre Will Be Measured And Paid Sepeartely. 108 Supply, Fixing, Flush To Wall, Fabrication, Expoxy Powder Coating Over A Coat Of Red Oxide Primer For Meter Box 4 Rooms Single Phase Made Up Of Ms Sheet 2 Mm Thick Of Size 0.9 X 0.9 X 0.3 Mtrs Including Concealed In Wall, Ms Angle Irons, Cable Glands For Incomming & Outgoing, Neoprene Gasket For Front Door, Provision For Fixing Of 4 Nos Mcb Spnfor Meter Connection And Taking Down Old Unserviceable Meter Boxcomplete All As Specified And Directed At Site By Engineer-In-Charge 109 Supply And Fixing 20 / 32A, 240V, Spn Industrial Type Socket Outlet, With 2 Pole And Earth, Meal Enclosed Plug Top Alongwith 20 / 32A C Curve, Sp Mcb, In Sheet Steel Enclosure, On Surface Or In Recess, With Chained Metal Cover For The Socket Outlet And Complete Wtih Connections, Testing And Commissioning Etc, As Required Complete All As Specified And Directed 110 Taking Down Old Unserviceable Lt Cables 35 Sq Mm Size From Ducts Including Disconnecting Cables And Stacking Of Cables Within 50 Metres Leadcomplete All As Specified And Directed. 111 Supply Only Xlpe Insulated, Armoured Heavy Duty Electric Cable With Aluminium Conductor, 1100 Volts Grade, Cross-Sectional Area 4 Core X 35 Sq Mmcomplete All As Specified And Directed. 112 Laying And Fixing Of One Number Pvc Insulated And Pvc Sheathed / Xlpe Power Cable Of 1.1 Kv Grade Of 35 Sq Mm ( Clamped With 1 Mm Thick Saddle ) On Wall Surface As Required.Complete All As Specified And Directed. 113 Supplying And Laying Of Size 63 Mm Dia ( Od-63 Mm & Id-51 Mm Nominal ) Dwc Hdpe Pipe Isi Marked Along With All Accessories Like Socket, Bend, Couplers Etc. Conforming To Is 14930, Part- Ii Complete With Fitting And Cutting, Jointing Etc. Direct In Ground ( 75 Cm Below Ground Level ) Including Excavation And Refilling The Trench But Excluding Sand Cushioning And Protective Covering Etc., Complete As Required 114 Laying Of One Number Pvc Insulated Pvc Sheathed / Xlpe Power Cable Of 1.1 Kv Grade Of Upto 35Sq Mm Size In The Existing Rcc / Hume / Dwc / Metal Pipe As Required
