Paschimanchal Vidyut Vitran Nigam Limited has published Tender For Fire Fighting Work And Misc. Civil Work Electricity Store Centre Baghpat, Distt-Baghpat. Submission Date for this Tender is 07-05-2024. Civil Work Tenders in baghpat Uttar Pradesh. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 18-Apr-2024 | DATE EXTENDED-01 | Date | 29-04-2024 |
| 2 | 29-Apr-2024 | DATE EXTENDED-02 | Date | 07-05-2024 |
| FileName | File Description | File Size |
| 939e70ca-3ba7-45f7-bc22-f6e1232a045a.html | Tender Notice | 0 KB |
| BOQ_1587942.xls | Tender Document | 0 KB |
| OTHERTENDERPQC.pdf | Tender Document | 0 KB |
| PQC12TO113.pdf | Tender Document | 0 KB |
| SATANDEREDTENDERDOCUMENT.pdf | Tender Document | 0 KB |
| Tendernotice_1.pdf | Tender Document | 0 KB |
| Sl. No. | Item Description |
| 1 | Complete design & drawing of Fire Fighting System at Store Centre By Authorised Designer as per site Requirments direction of E/I & guide lines provided by CPWD General sepecification of works part-V (Wet Riser & sprinkler system) 2020. NSI |
| 2 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make of 80 MM diaMS pipe Class-C pipe of wall thickness = 4.85 mm (Heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 3 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make 100 mm dia Class "C" pipe of wall thickness = 5.4 mm MS pipe (heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint (P.O. red enamel paint) of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I.NSI |
| 4 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make 150 mm dia Class "C" pipe of wall thickness = 5.4 mm MS pipe (Heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint (P.O. red enamel paint) of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 5 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make200 mm dia Class "C" pipe of wall thicknessMS pipe (Heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint (P.O. red enamel paint) of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I. NSI |
| 6 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make 50 mm dia Class "C" pipe of wall thickness = 4.47 mm MS pipe (heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint (P.O. red enamel paint) of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I.NSI |
| 7 | Supply, Laying and testing of ISI marked Jindal, T.T Swastic, Prakash, Surya, or equivalent make of 25 mm dia Class "C" pipe of wall thickness = 4.05 mmMS pipe (heavy class) (specification as per IS 1239) for hydrant system including transportation of all materials up to worksite, loading, unloading and proper stacking at site, cutting of pipe of required length, edge preparation, welding, fixing and erection of pipes with M.S. flat iron strip & all specials i.e. elbow, bends, tees and flange, rubber gasket, nuts & bolts etc. in proper position and alignment etc. including excavation of trenches and back filling of earth, cutting of walls and floors if required and repair of the same as per direction of E/I and supports of pipe as per layout and jointing by welding, aligning the pipe line painting with a one Coat of primer coat and two coats of fire red colour paint (P.O. red enamel paint) of approved make and Quality & hydraulic testing as per direction of E/I Including cost of all Materials, Labours and T&P etc. as per direction of E/I.NSI |
| 8 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe 80MM dia size in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I. NSI |
| 9 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 200mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I. NSI |
| 10 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 150mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I.NSI |
| 11 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipe size 100mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I.NSI |
| 12 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipesize 50mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I. NSI |
| 13 | Providing and Fixing one coat of 4mm thick ‘PYPKOTE’ or COATEK anti rust pipe protection layer of approved make and quality including approved make primer as per manufactures specification and over lap of 25mm to make an impermeable layer on above MS Pipesize 25mm dia (under ground pipe) in trenches structural/ masonary etc. complete including surface prepration, cost of all Materials, Labours and T&P etc. as per direction ofE/I. NSI |
| 14 | Supply, fixing and testing in position ISI marked and approved make cast iron butter fly valve including all interal fittings of 80MM size withMS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction ofE/I.(ISI marked. Make- Kartar, Castle, Audco)NSI |
| 15 | Supply, fixing and testing in position ISI marked and approved make cast iron wafer type non return valve including all interal fittings of 80mm size withMS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction ofE/I. (ISI marked. Make- Kartar, Castle, Audco) NSI |
| 16 | Supply and installation of two way 63mm instantaneous inlet for fire brigade connection including provision of cast iron Butter fly valve the cost of butter fly valve shall be under separate item and making connection with 100NB fire fighting pipe, painting with fire red paints completing the work in all respect as per the direction of E/I Make- New age, Padmani, Guard, HS. NSI |
| 17 | Supply, fixing, testing and commissioning of single headed 63 mm dia gunmetal/S.S. landing hydrant valve flanged inlet with 63 mm female instantaneous outlet confirming to IS 5290 on the fire wet riser down comer including making 80NB pipe connecting with riser fixing the landing hydrant valves in proper position and alignment including supply of nuts, bolts ,gasket and caps chain etc and testing of the hydrant including cost of all Materials, Labours and T&P etc. as per direction ofE/I.(Make-Newage,Padmani, Getech, HS). NSI |
| 18 | Supply, fixing, testing and commissioning of 20mm dia bore and 30 meter long hose rubber lined Dunlop pipe and hose reel for first aid fire fighting confirming to IS 384 with full swing drum fixing brackets 5 mm dia shut off gunmetal brass nozzle 25 mm dia globe valve connection to the landing valve through adopter or directly from the riser through 25 mm dia GI pipe as required including 25 mm dia pipe length with all sockets, elbows and nipples etc. including providing and operating instruction on a metal plate and fixing it near hose reel The system shall be complete in all respect as per drawing including cost of all Materials, Labours and T&P etc. as per direction ofE/I.(Make-Newage,Padmani, Guard, HS). NSI |
| 19 | Providing and fixing gun metal /S.S. ISI marked 63 mm dia branch pipes and 20 mm dia nozzle as per IS 903 of approved make and quality as required. including cost of all Materials, Labours and T&P etc. as per direction ofE/I.( Make- HS,Newage, Superex, Padmani)NSI |
| 20 | Providing and fixing ISI Marked fire RRL hose pipe 15 meter long and 63 mm dia with ISI marked IS 903 gun metal male and female coupling of approved make and quality as required near wet riser including cost of all Materials, Labours and T&P etc. as per direction ofE/I. (Make- CRC, Newage, Padmani,HS).NSI |
| 21 | Providing and fixing Hose cabinet box size 600X750X250MMmade of16 gauge M.S sheet duly painted with PO red paint 03 coats with central 6mm thick glass door, lock handleand fixing support on wall Including cost of all Materials, Labours and T&P etc. as per direction ofE/I. NSI |
| 22 | Supply, fixing, testing & commissioningof electrical motor driven fire pump suitable for automatic operation of following jockey pump.(Make- Kirloskar, Crompton ) of Model no. D.B. 32/20 horizontal end suction type (a) Horizontally mounted centrifugal fire pump complete for delivery of 180 LPM against a total head of 50 meter with necessary pressure gauge of approved make including by pass arrangement for periodic testing of the working of the pump set with required length and size of pipe.The impeller shall be enclosed type and accurateky balanced dynamically The pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be stainless steel (b) Squirrel cage TEFC induction motor (2900 RPM) Crompton/Kirloskar/ABB as per IS 325-1978 suitable for 415 volt 3 phase 50 HZ (10 HP) for the above pump and flexible coupling with the pump. (c) Common bed plate of fabricated mild steel channel or cast iron type. (d) Suitable. cement concrete pump foundation and vibration clamping arrangement as required. (e) Pressure switch for pump for automatic operation including necessary wiring up to control panel.NSI |
| 23 | Supply, fixing, testing & commissioning of Diesel engine driven fire pump suitable for automatic operation consisting of following for hydrant system. (Make- kirloskar, Crompton) of model no. D.B. 100/32 horizontal end suction type (a) Horizontally mounted centrifugal fire pump model No DB/100/32 complete for delivery of 1850 LPM against a total head of50 meter so asto ensure a minimum pressure of 30 meter at highest and farthest outlet at the specified flow complete with necessary pressure gauge including by pass arrangement for periodic testing of the working of the pump set. The pump casing shall be of cast iron, impeller shall be of bronze and shaft shall be stainless steel. (b) Squirrel cage, TEFC induction diesel engine Model 3R1040 1800RPM 43 BHPfor the above pump and flexible coupling with the pump with 1800 RPM65 % efficiency without negative tabeance (c) Common bed plate of fabricated mild steel channel or cast iron type. (d) Suitable cement concrete pump foundation and vibration clamping arrangement as required. (e) Pressure switch for automatic operation of motor including necessary wiring up to control panel. NSI |
| 24 | Supply, installation, testing & commissioning of Diesel Engine driven pump exhaust M. S. Pipe calss "C" 150mm dia including fittings like flanges, bends, reducers etc. 50mm thick fibre wool insulation aluminium cladding, 21 gauge, necessary excavation, fixing of silender connections at engine exhaust, necessary supports, back filling, cutting and making good, bird proff and weather proof flap complete in all respect. NSI |
| 25 | Supply, installation, testing and commissioning of Monoblock Pump, "KIRLOKSKAR/ CROMPTON" make 44 mt. HEAD, 2900 RPM, TEFC motor, 7.5 HP directly coupled to Pump having 450 LPM discharge with bronze impeller, Mechanical seal and MS shaft, mounted on common base plate with coupling and coupling guard. NSI |
| 26 | Supply & Installation ofsubmersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work (f)three phase 7.5 HP outlet 65 mm dia. or more, Head 57/46, Discharge 24000/30000 LPH. CSI No. 19.32 (f) |
| 27 | Supply, installation, testing and commissioning of standard Fireman"s Axe (tested for 20000 Volts) with heavy insulated rubber handle (ISI marked). NSI |
| 28 | Supply, installation, testing and commissioning of CI Ball Valve, 25mm dia, "KARTAR" make (For Hose Reel). NSI |
| 29 | Supply, Installation, testing & commissioning ofsingle plate Non Return Valve, 150 mm dia, ISI marked, “KARTAR” make with fittings viz. flange, nut-bolt & rubber insertion etc. NSI |
| 30 | Supply, installation, testing and commissioning of Pressure Switch, IPS 100, “INDFOS” make 0 to 7 bar (Adustable) with socket, nipple, ball valve etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 31 | Supply, installation, testing and commissioning of Water cum Foam Monitor, 63mm dia “WIMCO/ NEWAGE/ HD” make complete with aluminum nozzle, made out of seamless hot dip galvanized pipe and gun metal couplings having locking arrangement etc. capable of moving to any direction in 360 degree angle horizontally and 105 degree angle vertically with Reqired sizButterfly Valve, matching flanges, nut bolt etc. (Note: cost oo butter fly Valve is in the separate item), pressure 20 bar , LPM 1750 or more. NSI |
| 32 | Supply, installation, testing and commissioning of gun metal single acting Air Release Valve (Spring loaded)with screwed inlet 25mm dia. Make "KARTAR"K616 or eqivqlent. NSI |
| 33 | Supply, installation, testing and commissioning of 01 Inch stainless steel FB5X Foam making nozzle for pipe size 100mm dia SS grade 304W, flow rate 225 LPM, Length 455 mm and working pressure 8kgf/Sqcm. NSI |
| 34 | Supply, installation, testing and commissioning of Foam chemical, AFFF- 6%, ISI marked, IS: 4989, "FIRECHEM" Make (Available in 20 ltrs. Capactiy PVC drum). NSI |
| 35 | Supply, installation, testing and commissioning of CIDF Sluice Valve, 150mm dia, “KALPANA or KIELOSKAR” brand, ISI marked, Cat No NRSV P.N. 1.0 (12CR12-GM-IS Flanged FF IS 1538 Tbl 4&6 cast Iron body & Wedge Shaft: 12CR12, boady and Wedgw seat: Bronze, Hand operated Wheel operationwith flange, nut-bolts & rubber insertion. (At suction). NSI |
| 36 | Supply, installation, testing and commissioning of Water cum Foam Monitor, 100mm dia “WIMCO/ NEWAGE/ HD” make complete with aluminum nozzle, made out of seamless hot dip galvanized pipe and gun metal couplings having locking arrangement etc. capable of moving to any direction in 360 degree angle horizontally and 105 degree angle vertically with 100mm Butterfly Valve, matching flanges, nut bolt etc. (Note: cost of 100mm butter fly Valve is in the separate item), flow 7Kg/Sqcm, LPM 3750 or more. NSI |
| 37 | Supply, installation, testing and commissioningof Mild steel FB5X Foam making branch pipe, 150 PSI, size standard. NSI |
| 38 | Supply, installation, testing and commissioning of Electric Motor Driven 40 H.P Fire pumping set suitable for automatic operation consisting of the following as per specifications (Make Kirlosker, Crompton) Pump Model DB-80/20:(a) Horizontally mounted, centrifugal type single fire pump having cast iron body, gunmetal/ bronze impeller, stainless steel shaft and capable of delivering 97 m3/ hr(1620 LPM) against a total head of 70 Mtrs. (b)Squirrel cage induction motor totally enclosed fan cooled type suitable for 400/400 volts (+5%) 3 phase, 50 Hz. A. C. supply of suitable capacity of not less than 40 HP for the above pump with synchronous speed of 2900 RPM confirming to IS: 325 and duly coupled with above pump with flexible coupling including earthing as per relevant Indian standard and specifications (c)Common bedplate for mounting pump and motor fabricated of suitable M.S. channel as per manufacturer’s recommendations. NSI |
| 39 | Supply, installation, testing and commissioning of cubical type floor mounted fire pump control panel fabricated from 16 Gauge M.S. sheet duly painted with stove enameled finish of approved make & shade and comprising of: (a)One incoming 250 ampere MCCB switch unit with 250 AMP MCCB AMP Tpn Busbar Volt metre, volt meter, selector switch and indication lights. (b) One 250 AMP MCCB unit with 63 AMP HRC fuses. (c) One 63 AMP MCCB unit with 63 AMP MCCB. (d) One fully automatic star delta starter suitable for main pump with overload relay, timer, push buttons and auto manual selector switch.(e) One fully automatic direct on line starter suitable for motor with O/L relay, Push Button and Auto/ manual selector switch. (f) Three phase indicating lamps. (g)Three panel type ampere meters one for each motor with ASS, CTS etc. (h)Three neon indication lamps. (i)Fully automatic diesel engine starting system with battery charger, indicating lights, transformer, rectifier, timer, voltmeter, Amp. Meter, selector switches, push buttons, auxiliary relay etc. NSI |
| 40 | Supply, installation, testing and commissioning of Pressure Gauge, stainless steel, Glycerin filled, 100mm dia 0-10 kg./cm2 “TIPCO/H-GURU” make with socket, nipple, ball valve, U tube etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 41 | Supply, installation, testing and commissioning of Pressure Switch, IPS 100, “INDFOS” make 0 to 7 bar (Adustable) with socket, nipple, ball valve etc. (One each for Main Electrical, Diesel Engine driven & Jockey Pump at delivery). NSI |
| 42 | Providing and fixing of 6 Sq mm FR PVC insulated 1100 V grade 3 core copper cableof approved make and quality includingits connection to main switch board & electric motor etc complete with testing as per direction by E/I. NSI |
| 43 | Supply, Installation, testing & commissioning of Butter Fly Valve, 100 mm dia, P. N. 1.0 “KARTAR” make, ISI marked, IS: 13095 complete with all fittings viz. Flanges, gasket, nut-bolts etc. NSI |
| 44 | Supply, Installation, testing & commissioning of Butter Fly Valve, 150 mm dia, P. N. 1.0 “KARTAR” make, ISI marked, IS: 13095 complete with all fittings viz. Flanges, gasket, nut-bolts etc. NSI |
| 45 | Supply, installation, testing and commissioning of Four way Fire Brigade Inlet, “NEWAGE” make cast iron comprising of 63mm gun metal instantaneous male inlet coupling with plug and cap chain as per IS: specification with flange, nut bolt, rubber gasket etc. NSI |
| 46 | Supply, fixing and testing in position ISI marked and approved make cast iron dual plate wafer type non return valve (check valve) including all interal fittings of 150 mm size withMS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction ofE/I. (ISI marked. Make- Kartar, Castle, Audco). NSI |
| 47 | Supply, fixing and testing in position ISI marked and approved make cast iron wafer type non return valve including all interal fittings of 100 mm size withMS flange, nuts, bolts and rubber gaskets etc. including its testing and cost of all Materials, Labours and T&P etc. as per direction ofE/I. (ISI marked. Make- Kartar, Castle, Audco) . NSI |
| 48 | Supply, installation, testing and commissioning of Manual Call Point, break glass type The call points should comprises of push button of reputed make enclosed in ABS box with M.S. chain and hammer. The push button will have one pair of normally open and one pair of close contacts. The push button would be on non-shrouded construction. The whole assembly of the push button in ABS box is enclosed on the external ABS front cover, which will be seated in the front means of breakable glass with neoprene gasket. Under normal conditions push button would be in depressed condition so long the front glass cover is broken. The push button will be released by the spring action that should give remote Fire alarm through the contacts. “AGNI” make or Palex. NSI |
| 49 | Supply, installation, testing and commissioning of Optical Smoke Detector, Smoke Detector part of the conventional detectors, "SYSTEM SENSOR" make. This range of detectors has been produced using the latest in manufacturing and design techniques, pushing out the boundaries of existing conventional detector technology. Combined with the latest state of the art optical chamber the detector provides efficient and accurate detection of fires with a high level of resilience to nonfire environmental influences. NSI |
| 50 | Supply, installation, testing and commissioning of Electronic Hooter with Flasher, 24 volt, DC operatable, made out of M.S. sheet heavy duty duly powder coated with epoxy powder coating, plastic body 500 mtrs. audible rangewith built in transformer etc.“AGNI” make. NSI |
| 51 | Supply, installation, testing & commissioning of Air Cushion Tank with air release valve, pressure gauge, drainpipe, drain valve. The air cushion tank shall be made of 250mm dia x 1.5 mtrs. long M.S. pipe 6mm thick, heavy duly C class with suitable stand for fixing on the ground. The air cushion tank shall be duly painted with two coats of red oxide primer & thereafter two coats of P.O. red enamel paint of reputed brand viz. “NEROLAC/ ASIAN / BERGER”. All necessary piping from the outlet of the pump to the air cushion tank shall also be done as per requirements. NSI |
| 52 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 150 mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump-for proper filtration of water) NSI |
| 53 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 100 mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump-for proper filtration of water). NSI |
| 54 | Supply, installation, testing and commissioning of CIDF type Y Strainer, 80mm dia with flange, nut-bolts & rubber insertion. The strainer shall be of reputed make “KARTAR/ BENDCO”. (One each for Electrical & Diesel Engine driven Pump-for proper filtration of water). NSI |
| 55 | Supply, installation, testing and commissioning of 150 mm dia CISprinkler Alarm Valve with water motor gong bell and trims as required, pressure gauges, drain valves, ball valves, check valves, strainers etc. Alarm valve shall be UL Listed (for fire fightingof HD or equivalent make).NSI |
| 56 | Supply, installation, testing and commissioning of 100 mm dia CISprinkler Alarm Valve with water motor gong bell and trims as required, pressure gauges, drain valves, ball valves, check valves, strainers etc. Alarm valve shall be UL Listed (for fire fightingof HD or equivalent make).NSI |
| 57 | Supply, installation, testing and commissioning of Pendent Q. B. Sprinkler, 680 C, “HD/ SPRAYSAFE/AQUA” make or equivalent, UL listed with M.S. Socket 15mm dia, Teflon tape, adhesives etc. NSI |
| 58 | Supply, installation, testing and commissioning of Micro Processor based Fire Alarm Control Panel,Ten Zone “AGNI” make. The panel shall be fully modular in construction with test facility on the front for testing entire circulatory of panel. It shall have glass door locking facility. The control panel shall be compact & lightweight and shall be made out of M. S. sheet heavy duty duly powder coated.The control panel shall be complete with 24 volt battery and battery back up arrangement. The Control Panel shall be having battery charging arrangement, Fire indication, short indication, fault indication, low battery indication, battery charging indication, AC on indication, DC on indication & buzzer.NSI |
| 59 | Supply, Installation, testing & commissioning ofsingle plate Non Return Valve, 100 mm dia, ISI marked, “KARTAR” make with fittings viz. flange, nut-bolt & rubber insertion etc. NSI |
| 60 | P/F openable steel glazed windows and ventilators of standard rolled Z section conforming to IS 7452 1974 and welded with (100×20×5) mm holdfast embedded in C.C. block (23×11.5×7.5) cm size of 1:2:4 proportion of cement, coarse sand, & 20mm graded stone ballast as per drawing etc. complete but excluding S/F of glass panes of 4mm thick with nuts glazing clips with special putty of approved make etc. The fabrication should conform to IS 1038 1975. including cost of all materials, labour & T&P etc. (Rate already Sanction by Agr. No. 20/2017-18)NSI |
| 61 | Same as above in Item no. 60but for fixed portion. (Rate already Sanction by Agr. No. 20/2017-18)NSI |
| 62 | Providing all materials and labour & carrying out water proffing treatment of internal surface (positive surface) of under ground water storage tank of RCC with following process : (a) drilling 10 mm dia and 100 mm deep holes in wall surface with 04 holes per sqm (b) insurting PVC nozzles in each hole (c) injecting water profing material (s) with pressure in each hole with prescribed pressure (d) completing with required layers i.e fibre mess, Pidigrout10M 710 of Dr. Fixit, 113 Fastflex of Dr. Fixit , Pidicrete URP 301 of Dr. Fixit, using cement and course sand etc as per prescribed procedure. NSI |
| 63 | Supply, installation, testing and commissioning of 80 mm dia strainer cum Foot valve along with all accessorieswith all labour and material cost etc. NSI |
| 64 | Supply, installation, testing and commissioning of 100 mm dia strainer cum Foot valve along with all accessorieswith all labour and material cost etc. NSI |
| 65 | Providing and fixing full way 10 mm Dia GM gate valve whith wheel, ISI mark heavy quality including supply of all materials , labour and T&P required for proper completion of work. NSI |
| 66 | Supply, laying, testing and commissioning of heavy duty cable ( aluminium conductor PVC insulated armoured served shethed cable 1100Volts grade at adeo\pth of 750 mm below GL over a cushion of 75 mm. thick sand all around and protected with burnt bricks on side and top. On surface the cable run shall be fixed on MS clamp etc of suitable size or as directed by tge engineer-incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamp etc. B8including necessary support clamp, connection legs complete in all respect. 4 core 50 Sqmm (3-1/2 core). PWD 501 (l) |
| 67 | Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. PWD No. 1149 |
| 68 | Supply and burying of 600mm x 600mm x 3mm copper plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and two earthing lead of two no. 8 SWG copper wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and copper wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. complete in all respect. PWD No. 705 |
| 69 | S/F full way CI Gate valve of 63 mm dia. With wheel , BSI mark heavy quality including supply of all labour , material andT & P for proper completion of work . (CSI No. 28.02) |
| 70 | S/F full way63/65 mm dia Fire hydrant Gun Metal Gate Valve heavy quality including supply of all labour , material andT & P for proper completion of work (CSI No. 28.03) |
| 71 | P/F Male & Female coupling 63/65 mm dia. Gun metal BSI marked confirming to IS:903 heavy quality including supply of all labour , material and T & P for proper completion of work (CSI No. 28.04) |
| 72 | P/F Short Branch pipe Gun Metal BSI marked heavy quality including supply of all labour , material and T & P for proper completion of work.(CSI No.28.05) |
| 73 | P/F 63 mm dia RLL Hose Pipe heavy quality having length 15.0 m including supply of all labour , material andT & P for proper completion of work. (CSI No. 28.06) |
| 74 | P/F MS Hose Box Single Door with stand for 15 mt RRL Hose heavy quality including supply of all labour , material andT & P for proper completion of work. (CSI No. 28.07) |
| 75 | Placing of 10 KL PVCTank over slab of 6 m staging including supply of all labour , material andT & P for proper completion of work. (CSI No.28.08) |
| 76 | Excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.5 Metreand lead upto 30 metreincluding filling, watering, and ramming of excavated earth into the trenches or into the space between the building and the side of the foundation. CSI No. 4.01 |
| 77 | Add to Earth work item (SI No. 4.01 to 4.03) for every additional 30m lead or partthereof or for every additional 1.5M lift or part thereof. CSI No. 4.04 |
| 78 | River Bed Fine Sand filling in plinth including supply of necessary quantity of fine sand from outside the UPPCL premises including watering, dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work CSI No. 4.05 |
| 79 | Earth filling under floors and road including cost of the earth when obtained from outside Corporations area including its carriage loadingunloading watering, ramming in 20cm layers and dressing of earth etc. Rate includingcost of earth, labour ,T&Pand ROYALITY etc.required for proper completion of work. CSI No. 4.10 |
| 80 | Levelling and dressing and making proper slopes including cuttingand filling of earth upto a depth 100mm if so required includingall labour T&P etc. required for proper completion of the work. CSI No. 4.11 |
| 81 | Concrete with 4cm gauge I class brickballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion. CSI No. 5.01 |
| 82 | Concrete with 4cm gaugestone ballast, coarse sand (F.M. 1.8 to 2.5) & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. CSI No. 5.02 |
| 83 | Concrete with 4cm gaugestone ballast, coarse sand(F.M. 1.8 to 2.5) and cement in proportion of 8:4:1 in foundation & under floors including supply of all materials, labour & T&P etc. complete. CSI No. 5.04(a) |
| 84 | Cement concrete with 2cm gauge approved hard stone ballast,coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 4:2:1including supply of all materials, labour,side shuttering ifrequired and T&P etc. required for proper completion of work. CSI No. 5.06 |
| 85 | S/F 40 mm thick precast RCC jali (approx 0.5 Sq.M. Size) ofapproved design with 1:3 cement, coarse sand mortar and 1.6 mm dia M.S.reinforcement with cost of all materials labour and T&Pcomplete including cutting required grooves in walls and grouting. CSI No. 5.17 |
| 86 | Concreting of 40 mm thick RCC trench covers in mild steel framework with RCC 1:1.5:3 in Cement,Chopan coarse sand(F.M. 1.8 to 2.5) and 2cm gaugegraded hard stone ballast with 3mm thick floating coat of neatcement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area. CSI No. 5.18 |
| 87 | Cement concrete with 2cm gauge approved hard stone ballast,coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 3:1.5:1including supply of all materials, labour,side shuttering ifrequired and T&P etc. required for proper completion of work. CSI No. 5.21 |
| 88 | Precast cement concrete door sills, chaukhats boundary posts,shelves and similar small work with cement, approved coarse sand(F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast in the proportion 1:1.5:3, excluding reinforcement but including fixig the same in position including cost of all other material, labor and T&P . CSI No. 5.22 |
| 89 | RCC work with cement, approved coarse sand(F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. CSI No. 5.23 |
| 90 | RCC work with cement, approved coarse sand(F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3inslab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P CSI No. 5.24 |
| 91 | RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3inlighter beams i.e. having span upto6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. CSI No. 5.25 |
| 92 | RCC work with cement, approved coarse sand(F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granitet, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3in heavier beams i.e. having span above6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. CSI No. 5.26 |
| 93 | RCC work with cement, approved coarse sand(F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granite quartzite etc from Dalla, Jhansi or other quarries in proportion1:1.5:3 in raft foundation and footings , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P.CSI No. 5.27 |
| 94 | Same as item no 5.15ain RCC pile caping, gantry walls/columnfoundations and RCC pedestals but in the proportion 1:1.5:3..CSI No. 5.28 |
| 95 | RCC work with cement, approved coarse sand (F.M. 1.8 to 2.5) and2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3in RCC T beam-slab and column, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. CSI No. 5.29 |
| 96 | First class brick work in 1:6 cement and coarse sand(F.M.1.8 to 2.5) mortar in foundation and plinth including supply of allmaterials, labour & T&P etc. required for proper completion of work. CSI No. 6.01 |
| 97 | First class brick work in 1:4 cement and coarse sand (F.M.1.8 to 2.5)mortar in foundation and plinth including supply of allmaterials, labour & T&P etc. required for proper completion of work. CSI No. 6.03 |
| 98 | First class brick (class-150) work in 1:6 cement and coarse sand (F.M. 1.8 to 2.5) mortar in super structure including necessary cutting and moulding of bricks as required and also including honeycomb brick work for wall of one brick thick (230mm) including supply of all materials, labour & T&P etc. required for proper completion of work.CSI No. 6.01+6.07+6.08 |
| 99 | First class brick (class-150) work in 1:4 cement and coarse sand (F.M. 1.8 to 2.5) mortar in super structure including necessary cutting and moulding of bricks as required and also including honeycomb brick work for wall of 1½ brick thick (115mm) including supply of all materials, labour & T&P etc. required for proper completion of work.CSI No. 6.03+6.07+6.09 |
| 100 | Brick work in foundation & plinth with old dismantledbricks (supplied by department free of cost) and coarse sand of F.M. 1.8 to 2.5mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. CSI No. 6.18 |
| 101 | Brick work in super structure for 230 mm thick wall with old dismantledbricks (supplied by department free of cost) and coarse sandmortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. CSI No. 6.19 |
| 102 | Mild Steel or Iron work in heavy sizes such as trusses built upgates, door frames, record, racks roof work gates etc. wrought torequired form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor.CSI No. 9.01 |
| 103 | As in item 9.01 above but when steel is to be provided by the department.CSI No. 9.02 |
| 104 | TMT/Tor steel in plain work such as reinforced concrete orreinforced brick work (when not included in an over all rates)wrought to required shape as necessary including bending forproper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (Steel shall be arranged by the contractor)CSI No. 9.03 |
| 105 | Providing and Fixing barbed iron wire fencing including stretching, fixing into the post including all labour, materials and T&P required for proper completion of work. the weight of hot dipped GI barbed wire having 12 SWG - 2 ply wires and 4 point ordinary barbs @ 150 mm (approx) C/C should be 100 gm per Meter CSI No. 9.07 |
| 106 | Supply and fixing galvanised mosquito proof jali (16x24 gauge) withM.S. flat of 20 x 3 mm. size, on both sides screwed or welded to windowor door frame. CSI No. 9.18 |
| 107 | 12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. CSI No. 11.07 |
| 108 | Rough cast finish to plasters of different mortars,add extra toplaster itemsCSI No. 11.11 |
| 109 | Add for extra labour and materials for plaster over rough face ofone brick thick wall.(CSI No. 11.12) |
| 110 | 2 cm. thick cement plaster in dado or skirting in 1:2 consisting of onepart of cement and two parts of approved coarse sand laid inpanels finished with 3mm.floating coat of neat cement or cementand marble dust in ratio of 5:1 including supply of all materials, labour & T&P etc. required for proper completion of the work. (CSI No.11.13) |
| 111 | Engraving lines in the plaster of the outer face wall verticallyand horizontally to display the surface as stone facing asdirected by the engineer incharge including labour and T&P etc.required for proper completion of the work (Add for extra labour and T&P etc. required for proper completion of the work (Add for extra labour to all items of plaster).(CSI No. 11.14) |
| 112 | S/mixing approved water proofing compound (CICO,DR FIXIT etc) in cementmortar in plaster or concrete work in the proportion as recommended by the manufacturer.(CSI No. 11.15) |
| 113 | Providing (12x15) mm section groove in plasterincluding all material, labour andT&P etc. required for proper completion of the work. (CSI No. 11.16) |
| 114 | Making drip coarse (25x12) mm in 1:2 cement and coarse sandincluding supply of all materials, labour and T&P etc requiredfor proper completion of work. (CSI No. 11.19) |
| 115 | 3 mm thick floating coat of neat cement finish including supply of all materials,labour and T&P etc. required for proper completion of the work.( cement consumption 0.044 bag/Sq.m.) (CSI No. 11.20) |
| 116 | 4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC. (CSI No. 12.04) |
| 117 | Supply and Laying 8 mm thickglazed floor tiles of Somany, Johnson or equivalent make, , laid with1:3 cement and approved coarse sand mortar finished with whitecement slurry, jointing and polishing complete, including supplyof all materials, labour and T&P etc. required for proper completion of the work.(CSI No. 12.11) |
| 118 | Providing and fixing glass strips of 3.15 mm thickness & 40mm depth in jointsof floor and skirting at the time of laying floors, flush withfloor level including supply of all materials, labour& T&P etc. required for proper completion of work. (CSI No. 12.14) |
| 119 | Supply and laying of 80 mm thick I shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200X(160+120 mm) with minimum 5 mm thick toping of O.P.Cement mixed with 25% marble powder. The compressive strength of concrete pavers blocks shall not be less than 30 MPa & 4.5 Kg/No. including cost of all material, labour, T&P etc. required for proper completion of work as directed by Engineer-in-charge but excluding G.S.T. which shall be paid extra as per rules. (CSI No.12.23) |
| 120 | Painting or varnishing new iron work in small areas or new woodwork with one coat of ready mixed priming paint and one coat ofapproved superior quality ready mix paint "Luxol" or equivalentbrand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950.(CSI No. 13.01) |
| 121 | As in item 13.01 above but for every coat after first coat. (CSI No. 13.02) |
| 122 | As in item 13.01 above but for every coat on previously paintedold wood or iron work including its sand papering,rubbing andcleaning as required, for proper completion of work. (CSI No. 13.03) |
| 123 | One priming coat and one coat oil bound distemper on new work includingsupply of all materials,labour and T&P etc. required for propercompletion of the work. (CSI No. 13.08) |
| 124 | As in item 13.08 but for every coat after the first coat. (CSI No. 13.09) |
| 125 | As in item 13.08 but for every coat on previously old oil bound distemper surface. (CSI No. 13.10) |
| 126 | Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work. (CSI No. 13.20) |
| 127 | Painting one coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (CSI No. 13.22) |
| 128 | Same as in item no 13.22 above but for every coat of additional APEX or equivalent brand weather coat paint . (CSI No. 13.23) |
| 129 | Dismantling brick work or stone work in lime or cement mortar andincluding stacking of materials as directed by theEngineer-in-charge within a distance of 60 metres. (CSI No. 15.01) |
| 130 | Dismantling reinforced cement concrete or reinforced brick work,including stacking of dismantled materials as directed by theEngineer-Incharge within a distance of 60 metres.(CSI No. 15.03) |
| 131 | Dismantling cement concrete or brick or granolithic floorsincluding base concrete and including stacking of dismantledmaterials as directed by the Engineer In-charge within a distanceof 60 metres. (CSI No. 15.05) |
| 132 | Providing and laying non-pressure NP3 class RCC pipes with collars with stiff mixture of cement mortar in the proportion 1:2 (1-Cement, 2-Coarse sand) including testing of joints including cost of all material, labour, T&P etc. required for proper completion of the work. (a) 150 mm dia RCC pipe(CSI No. 18.16-A) |
| 133 | Same as item No. 18.16-a but for (b) 300 mm dia RCC pipe (CSI No. 18.16-B) |
| 134 | Developing the tubewell by the air compressor having a capacity of 8.5 CuM or by the borehole pumping set having the capacity of 0.7 CuM/sec as per direction of Engineer I/C. (CSI No. 19.01) |
| 135 | Drilling bore from G.L. to 180 M B.G.L., work to be completed as per direction of Engineer I/C .(E) As per 19.04 above but for 300 mm dia. boring. (i) from 0 M BGL to 90 M BGL. CSI No. 19.04-E(i) |
| 136 | Same as item No. 129above but for (ii) from 90 M BGL to 120 M BGL.CSI No. 19.04-E(ii) |
| 137 | Same as item No. 129 above but for (iii) from 120 M BGL to 150 M BGL.CSI No. 19.04-E(iii) |
| 138 | Development of tubewell by O.P. Unit (5 HP to 10 HP submersible pump set), including bringing Column pipe for the OP unit, assembling, electric connections, running for required period, dismentling and taking out & carrying away and cleaning the site with cost of all labour, materials, T&P and fuel / Electricity Charges etc required for proper completion of work and as per direction of Engineer-in-charge. (CSI No. 19.14) |
| 139 | Supply and fixing of G.I. ("B" class ) column pipes JTC/ JINDAL make with column coupling socket as required for proper completion of workincluding all labour material & T&P. (a)80 mm dia. (CSI No. 19.22-a) |
| 140 | Supply and fixing C.I. non-return valveISI marked and approved make with nuts, bolts, packing etc completeincluding all labour material & T&P. (a)80 mm dia..(CSI No. 19.23-a) |
| 141 | Supply and fixing support clamps for column pipesmade out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (a) 80 mm dia.(CSI No. 19.24-a) |
| 142 | Transportation and installation of tube well drilling Rig m/c, compressure for development and other required equipments and accessories at site of work and dismentlling & taking them back after successful completion of the work including cleaning, levelling - dressing the site properly, also disposing off the surplus earth, silt, sand etc.(CSI No. 19.28) |
| 143 | Supply and installation of 5H.P. Kirloskar or equivalent make single stage, horizontal, self priming,three phase dewatering pumpset of specification Head 14/16 M, Discharge 13.6/10 LPS, solid handle size 15.5 mm, suction 80 mm, delivery 80 mm, RPM 1500 including cost of 80 mm dia G.I. pipe for suction (3M) and delivery (4.5 M).(CSI No. 19.29) |
| 144 | Supply & installation of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser.(d) for 5 H.P pump set three phase(CSI No. 19.31-d) |
| 145 | Supply and fixing of submersible cable Havelsor equivalent make, for submersible pump complete in all respect. (c) 4.0 mm2 for pumpabove 3 HP and up to 7.5 H.P. (CSI No. 19.33-c) |
| 146 | Providing and lowering of 200 mm. Outer dia P.V.C. pipe of ‘Supreme/Astral" or equivalent make (as approved sample by by Engineer-in-charge) 10kg/Sq.Cm pressure pipe confirming to ISI 498S/1988 required cost of all materials, labour and TandP etc. required for proper completion of work. CSI No. 18.08 (As per Old Schedule) |
| 147 | Providing and lowering of P.V.C. strainer pipe of 200 mm. Outer diameter of ‘Supreme, /Astral’ or equivalent make(as approved by Engineer-in-charge) 10kg/Sq.Cm pressure pipe confirming to ISI 498s/1988 with appox. (60x3) mm size slots all over surface of pipe and rolled with best quality plastic mesh binding with plastic wire as per direction of Engineer-in-charge including cost of all materials, labour and TandP ete required for proper completion of work. CSI No. 18.09 (As per Old Schedule) |
| 148 | Providing and fixing of 200/160 mm. dia P.V.C. top or bottom plug/bail plug of ‘Supreme/Astral’ or equivalent make of heavy quality including cost of all materials, labour, TandP etc required for proper completion of work. CSI No. 18.12 (As per Old Schedule) |
| 149 | Providing and fixing 80 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete.(CSI No. 26.01-H) |
| 150 | Providing and fixing 100 mm dia B-class Jindal,JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete.(CSI No. 26.01-i) |
| 151 | Providing and fixing 80 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02-H) |
| 152 | Providing and fixing 100 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02-i) |
| 153 | Providing and fixing full way 80mm dia G.M. gate valvewith wheel, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04-H) |
| 154 | Providing and fixing full way 100mm dia G.M. gate valvewith wheel, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04-i) |
| 155 | Providing & fixing half turn 80mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05-H) |
| 156 | Providing & fixing half turn 100mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05-i) |
| 157 | Providing and fixing NON RETURN REFLEX VALVE, 80 mm dia ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.07-H) |
| 158 | Providing and fixing NON RETURN REFLEX VALVE, 100 mm dia ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.07-i) |
| 159 | P/F GI UNIONS NOMINAL BORE 80 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10-H) |
| 160 | P/F GI UNIONS NOMINAL BORE 100 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10-i) |
| 161 | Providing and fixing SLUICE VALVE, CI 80 mm dia. WITH Wheel. ISS:780 & ISS: 2906 class - I, "MEC" make, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.(CSI No. 26.11a) |
| 162 | Supply and fixing of Syntex or equivalent make water storage tank including all materials, labours, T&P etc required for proper completion of work. (CSI No. 26.12) |
| 163 | P/F 80 mm dia BRASS WHEEL VALVE, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.15-H) |
| 164 | Supply and fixing 24 watt LED tube light Phillips, Havells and equvalent make including its fixing & T&P. NSI |
| 165 | Supply and fixing 100 watt outdoor flood light Havells and equvalent make including its fixing as per direction of E/I. NSI |
| 166 | Supply and stacking pee gravelproperly at levelled ground for measurement as directed by Engineer I/C, including all labour, T&P required for proper completion of work. CSI No. 19.25 |
| 167 | Providing and fixing of self supported arch shaped mechanically seamed trussless galvalume roofing system such as Proflex or similar as approved by Engineer-in charge, made of superior quality structural grade steel, having 350 MPA yield strength, pre coated galvalume sheet as per ASTM A 792 M of base thickness 1.0mm ( tolerance +/- 0.02mm) with minimum coating mass as per AZM 150. Total coated thickness 1.075mm ( tolerance +/- 0.02mm). Roofing should be designed as per ASCE 7-20 international building code 2002. The analysis shall be carried out for span and center arch-rise considering the required live load, wind load, dead load and the seismic factor. The roof panel formation shall be done as per the required length and curvature using hydraulic profile machine to give it the trapezoidal shape in required curvature. In this process the width of the sheet reduces from 0.914 meter to 0.61 meter (tolerance +/- 0.02m). The roof panel shall be lifted using a suitable crane and using a spreader bar and sling evenly placed to ensure no distortion of the panels during lifting and placing. The crane shall hold/support the panel till the alignment is done and completed using a plumb and a water tube and bolted into beam. These curved panels have interlocking formation and are crimped together using mechanical seaming machine, which imposes a load of approximately five tones to ensure the seaming of required rigidity. After seaming, a clear epoxy lacquer is applied on the inner side of panel end in 15cm width to form a protective layer between panel and concrete beam. These panels are installed over existing water proof concrete gutter-beams having beveled edge to receive (support) curved panels. Beam shall design for arch reaction and vertical loads. Plaster shall not be applied on the beam. Schmidt Hammer test of the concrete should be carried out before erection to ensure that the anchor bolt can be securely fixed on support. In case of steel structure a steel runner plate of 6mm thickness and G.I sheet gutter of suitable size shall be provided for installation of panels, G.I anchor bolt of required sizes and type with G.I washer and neoprene washers shall be provided as per design After installation of panels, trapezoidal voids are created between gutter- beam and panels which should be covered by a flashing fabricated or brick masonry included. Area of this roof shall be measured along the periphery of hem-top between end to end of panels. Ridge and valley shall not be taken into consideration for measuring length transverse to periphery. The rate includes supplying, fixing, loading unloading, hire charges of all plants machineries, anchors, fasteners, washers, bolts, epoxy, paint and all wastage etc. complete. Accessories and fixtures like hangers/clamps for installationoflighting/fixtures/utility/duct as per requirement and ventilators, skylight can also be provided at crown/ridge by making cuts into the panels, included. This item shall be executed only by the agency, which has all require manufacturing machineries and necessary expertise as per Direction of E/I. NSI |
| 168 | Supply and Installtion Aluminum Construction, Size 24", Capacity 2300 CFM, With Complete Fixing Accessories of Wind Operated Turbo Ventilators as per E/I.NSI |
| 169 | Supply and Installtion of Skylight Sheet, Size 2X14 Ft, 2MM Thick Polycarbonate Sheet, with Complete fixing accessories as per E/I. NSI |
| 170 | Providing and fixing of 110 mm dia PVC pipe 6 Kg/ Sq.cm forwith special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. (CSI No. 26.17) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
