Construction Of Rcc Hl Bridge At Ch 2 080 In T12-Kadwara To Ramkhetariya Road
Tender Value
3.54 Crore
Estimated cost
Bid Submission
25 Mar 2024
0 days left
EMD
7.09 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
biraul → Bihar
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Rcc Hl Bridge At Ch 2 080 In T12-Kadwara To Ramkhetariya Road
BOQ
| Sl. No. | Item Description |
| 1 | Excavation for Structures |
| 2 | Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. |
| 3 | I. Ordinary Soil |
| 4 | i) Upto 3m depth |
| 5 | Providing and Constructing Temporary Earth Island (Assuming depth of water 1.0 m and height of island to be 1.25 m including Royality for earth @ Rs. 5526.00 for each Island.) |
| 6 | Providing and constructing one span service road to reach island location from one pier location to another pier location including Royality for earth @ Rs. 225.00 per m for service Road. |
| 7 | Bored cast-in-situ M35 grade R.C.C. Pile excluding Reinforcement complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead upto 1000 m. (II.1200 mm Dia(UsingBatching Plant, Transit Mixer and Concrete Pump)) |
| 8 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (II. PCC Grade M-15 (Levelling Course)) |
| 9 | R.C.C. grade M 30 in Pile Foundation complete as per Dwg & Tech Specification. (Pile Cap in RCC M-30 (UsingBatching Plant, Transit Mixer and Concrete Pump)) |
| 10 | Providing steel liner 10 mm thick for curbs and 6mm thick for steining of wells including fabricating and setting out as per detailed drawing |
| 11 | Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202 |
| 12 | a) Initial Load Test on test pile for 2.5 times the design load specified in Drawings |
| 13 | b) Routine pile load test on pile for 1.5 times the design load specified in Drawings |
| 14 | c) Horizontal pile load test on pile for 1.5 times the design load specified in Drawings |
| 15 | SUBSTRUCTURE |
| 16 | R.C.C. grade M-30 in Substructure complete as per Dwg & Tech Specification |
| 17 | RCC M-30 |
| 18 | i) Upto 5m height (Using Concrete Mixer) |
| 19 | ii) From 5m upto 10m height (Using Concrete Mixer) |
| 20 | R.C.C. grade M-35 in Substructure complete as per Dwg & Tech Specification |
| 21 | RCC M-35 |
| 22 | ii) From 5m upto 10m height (Using Concrete Mixer) |
| 23 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 |
| 24 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 |
| 25 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 |
| 26 | I) Sandy Material |
| 27 | Providing and laying filter media with granular crushedaggregates (Jhama Metal)as per specification to a thickness of not less than 600 mm with smallersize towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specificationClause 1204.3.8 |
| 28 | Supplying,fitting and fixing in position true to line and level POT-PTFE bearing consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cylinder,sealing rings,dust seals,PTFE surface sliding against stainless steel mating surface,completre assembly to be of cast steel/fabricated structural steel,metal and elastomer elements to be as per IRC: 83 part-I & II respectively and other parts conforming to BS: 5400,section 9.1 & 9.2 and clause 2006 of MoRTH Specifications complete asper drawing and approved technical specifications. |
| 29 | Supplying,fitting and fixing in position true to line and level elastomeric bearing conforming to IRC: 83 (Part-II) section IX and clause 2005 of MoRTH specifications complete including all accessories as per drawing and Technical Specifications. |
| 30 | SUPERSTRUCTURE |
| 31 | Providing and laying reinforced cement concrete in superstructure complete as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 |
| 32 | II. RCC M-25 (Height 5m to 10m) |
| 33 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in superstructrue complete as per drawings and technical specification Clauses 1002, 1010 & 1202 |
| 34 | Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 |
| 35 | Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000mm as per drawing and technical specifications Clauses 800, 900 and 1208.3 |
| 36 | Drainage Spouts complete as per drawing and technical specifications Clause 1209 |
| 37 | P.C.C. M-15 ordinary grade (1:2.5:5) levelling course below approach slab complete as per drawing and technical specificatios Clauses 800 & 1211. |
| 38 | Reinforced Cement Concrete M-30 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications Clauses 800 and 1211 |
| 39 | Strip Seal Expansion Joint (Providing and laying of a strip seal expansion joint catering to maximum horizontal movement upto 70 mm,complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer\"s instructions for installation.) |
| 40 | Providing & fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing & Technical Specification. |
| 41 | Providing and fixing in position 20 mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans not exceeding 10 m to cater for a horizontal movement upto 20 mm,covered with sealant complete as per drawing and technical specifications. |
| 42 | PROTECTION WORK |
| 43 | Providing and laying boulder pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302 |
| 44 | Providing and laying boulder apron for bed protection with stone boulders of minimum sizeand weight as per Table 1300.1, no fragment weighing not less than 25 Kg, laid dry complete as per drawing and technical specifications Clause 1301. |
| 45 | I. Rubble stone laid in cement mortar 1:3 |
| 46 | E. APPROCH ROAD |
| 47 | Clearing and Grubbing Road Land ( By manual means)including uprooting wild vegetation , grass ,bushes ,shrubs , saplings and trees ofgirth upto 300mm , removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification - clause 201.1 and direction of E/I |
| 48 | Construction of Embankment with material obtained from borrow pits with a lift upto 1.5 m , transporting to the site spreading , grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 . |
| 49 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. |
| 50 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mounted grader arrangement on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification Clause 401. |
| 51 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with threewheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. |
| 52 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with threewheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. |
| 53 | Providing and applying primer coat with Bitumen emulsion (SS-1)on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502. |
| 54 | Providing and applying tack coat with bitumen emulsion (RS ) using emulsion distributor @ 0.2 to 0.25 kg per sq m on the prepared bituminous surface cleaned with hydraulic broom as per technical specification clause 503. |
| 55 | Providing , laying and rolling of open graded premix carpet of20 mm thickness composed of 13.2 mm to 5.6 mm agreegates either using penetration grade bitumin or emulsion to reqired line grade , and levelto serve as wearing course on a previously prepared base , including mixing in a suitable plant , laying and rolling with a three wheel 80-100 KN static roller capacity , ifnished to required level and grades to be followed by seal coat of either Type A or Type B or Type as per Technical Specification clause 508 |
| 56 | Providing , laying seal coat sealing the voids in a bituminous surface laid to the specified levels ,grades and cross fall using Type B as per the specification in clause 510 ( With Bituminous Binder S-90 ) |
| 57 | Providing and Fixing \"Logo\" of Projectinformayory sign board with Logo as per MORD specifications and drawing.Three MS plates of1.6mm thick, top and middle plate duly welded with MS flat iron 25mm x 5 m size on back on edges.The lower plate will be welded with MS angle ironframe of25mm x 25mm 5mm.The angle iron frame of the lower mostplate and flat iron frame of middle plate will be welded to 2 Nos.75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600 mm,600 mm,600 below ground level.The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12SWG steel plate tube.All M.S will be stove enameled on both sides. Lettering and printing arrows, border etc, will be painted with ready mixed synthetic enamer paint of superior quality in required shade and colour.All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 abd Annexure 1700.1. |
| 58 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. |
| 59 | Providing and erecting a \"W\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810 |
| 60 | LABOUR CESS @ 1 % = |
| 61 | GST @ 18 % |
| 62 | SEIGNIORAGE FEE @ 10 % |
| 63 | Total Cost for 1st Year Maintenance Work |
| 64 | Total Cost for 2nd Year Maintenance Works |
| 65 | Total Cost for 3rd Year Maintenance Works |
| 66 | Total Cost for 4th Year Maintenance Works |
| 67 | Total Cost for 5th Year Maintenance Works |
| 68 | LABOUR CESS @ 1 % = |
| 69 | GST @ 18 % |
| 70 | SEIGNIORAGE FEE @ 10 % |
AI Tender Summary
Tender Timeline
Mar 18, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedMar 25, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 25, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender