Rural Works Department has published Tender For Construction Of Road And Bridge Work - Ndb-Brrp2-598-Muzaffarpur West. Submission Date for this Tender is 25-03-2024. Road Work Tenders in muzaffarpur Bihar. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | REO Road toHouse of Satendra Mishara - Setting out(i) Construction of Reference & Working Benchmark = 1 Nos. & 2 Nos. RespectivelySOR Item No.-1.16 |
| 2 | (ii) Construction of Reference Pillars/Burjees = 13 NosSOR Item No.-1.16 |
| 3 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.SOR Item No.-2.2 |
| 4 | Excavation for roadway in soil using manual means for carrying of out earth to embankment site with a lift up to 1.5 m and lead up to 50m as per Technical Specification Clause 302.3.SOR Item No.-3.5 (I) |
| 5 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5.SOR Item No.-3.3 |
| 6 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 1000 m as per Technical Specification Clause 301.5SOR Item No.-3.4 |
| 7 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 100 m as per Technical Specification Clause 301.5SOR Item No.-3.5 (ii) |
| 8 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 100 m as per Technical Specification Clause 303.1.SOR Item No.-3.14 |
| 9 | Construction of granular sub-baseby providingwell gradedmaterial (Grading I) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with threewheel 80-100 kN static roller capacity to achieve thedesired density, complete as per Technical Specification Clause 401SOR Item No.-4.1.401(Aii) |
| 10 | WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.80 -100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.SOR Item No.-4.7 (3)(A) |
| 11 | Cement Concrete Pavement Construction ofun-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawingand Technical Specification Clause 1501SOR Item No.-6.4 |
| 12 | Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with threewheel road roller 80-100 kN as per Technical Specification Clause 412SOR Item No.-4.18 |
| 13 | Earthwork excavation for foundation of structures as per drawing and teachnical specification clause 1104 includding setting out, stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved matefial . (A)Ordinary soilSOR Item No.-11.1 (I) |
| 14 | Providing concrete for plain/reinforced concrete in opne foundations complete as per drawwings and technical specifications clause 802,803,1202&1203(I) PCCGrade M-10 Nominal mix 1:2.5:5 with 40mm and down graded metelSOR Item No.-11.4(II) (i) |
| 15 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 PCC M15SOR Item No.-11.4 (II) |
| 16 | Providing concrete for plain/reinforced concrete (M-20 Nominal mix 1:2:4) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203Bed Portion SOR Item No.-11.4 (III) |
| 17 | Brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications clauses 600,900 and 1208.4SOR Item No.-13.9 |
| 18 | Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification clauses 613.4 & 1204SOR Item No.-12.3 |
| 19 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8SOR Item No.-12.10 |
| 20 | Guide PostSOR Item No.- |
| 21 | Bedding for Type - B PCC(M20) Bedding Laying (First Class ) bedding concrete as per clause 1105 (ii)SOR Item No.-9.2 |
| 22 | Providing and Laying Reinforced Cement Concrete Pipe NP3 1000 mm diaas per design in Single Row SOR Item No.-9.3 |
| 23 | Providing and laying reinforced cement concrete pipe NP4 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapaets clause 1106. SOR Item No.-9.3(C) |
| 24 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 SOR Item No.-(I)(II) Ordinary Kilometer Stone (Pre-cast) |
| 25 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 SOR Item No.-10.1(III) 200m Stone (Pre-cast) |
| 26 | Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704At outer side of H-Curve & @ 1.50m c/c both side at heigh embankment SOR Item No.-10.11 |
| 27 | Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level.The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube.All M.S. will be stove enameled on both sides.Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour.All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 SOR Item No.-10.16 |
| 28 | Maintenance Board |
| 29 | MMGSY Logo Board |
| 30 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1)(ii) 600 mm equilateral triangle |
| 31 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1) (v) 600 mmx 450 mm rectangular |
| 32 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. Painting on concrete surface Providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt dust oil grease efflorescence and applying @ of 1 liter for 2 sqm. |
| 33 | Rumble Strips (Provision of 15 nos rumble strips covered with MSS bituminous carpet, 15-20 mm high at center, 250 mm wide placed at 1 m center to center at approved locations to control speed, marked with white strips of road marking paint.) unit is Sqm |
| 34 | Rumble Strips - Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. Unit is Sqm |
| 35 | Add 1% Labour Cess |
| 36 | Add 18% GST |
| 37 | Add 10% Seigniorage Fee |
| 38 | Maintainance for 1st year |
| 39 | Maintainance for 2nd year |
| 40 | Maintainance for 3rd year |
| 41 | Maintainance for 4th year |
| 42 | Maintainance for 5th year |
| 43 | Add 1% Labour Cess |
| 44 | Add 18% GST |
| 45 | Add 10% Seigniorage Fee |
| 46 | REO Roadto Ara Sahni Tola - Setting out(i) Construction of Reference & Working Benchmark = 1 Nos. & 1 Nos. RespectivelySOR Item No.-1.16 |
| 47 | (ii) Construction of Reference Pillars/Burjees = 5 NosSOR Item No.-1.16 |
| 48 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.SOR Item No.-2.2 |
| 49 | Excavation for roadway in soil using manual means for carrying of out earth to embankment site with a lift up to 1.5 m and lead up to 50m as per Technical Specification Clause 302.3.SOR Item No.-3.5 (I) |
| 50 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5.SOR Item No.-3.3 |
| 51 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 1000 m as per Technical Specification Clause 301.5SOR Item No.-3.4 |
| 52 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 100 m as per Technical Specification Clause 301.5SOR Item No.-3.5 (ii) |
| 53 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 100 m as per Technical Specification Clause 303.1.SOR Item No.-3.14 |
| 54 | Construction of granular sub-baseby providingwell gradedmaterial (Grading I) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with threewheel 80-100 kN static roller capacity to achieve thedesired density, complete as per Technical Specification Clause 401SOR Item No.-4.1.401(Aii) |
| 55 | WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.80 -100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.SOR Item No.-4.7 (3)(A) |
| 56 | Cement Concrete Pavement Construction ofun-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawingand Technical Specification Clause 1501SOR Item No.-6.4 |
| 57 | Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with threewheel road roller 80-100 kN as per Technical Specification Clause 412SOR Item No.-4.18 |
| 58 | Earthwork excavation for foundation of structures as per drawing and teachnical specification clause 1104 includding setting out, stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved matefial . (A)Ordinary soilSOR Item No.-11.1 (I) |
| 59 | Bedding for Type - B PCC(M20) Bedding Laying (First Class ) bedding concrete as per clause 1105 (ii)SOR Item No.-9.2 |
| 60 | Providing and laying reinforced cement concrete pipe NP4 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapaets clause 1106. SOR Item No.-9.3(C) |
| 61 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 SOR Item No.-(I)(II) Ordinary Kilometer Stone (Pre-cast) |
| 62 | Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704At outer side of H-Curve & @ 1.50m c/c both side at heigh embankment SOR Item No.-10.11 |
| 63 | Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level.The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube.All M.S. will be stove enameled on both sides.Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour.All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 SOR Item No.-10.16 |
| 64 | Maintenance Board |
| 65 | MMGSY Logo Board |
| 66 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1)(ii) 600 mm equilateral triangle |
| 67 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1) (v) 600 mmx 450 mm rectangular |
| 68 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. Painting on concrete surface Providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt dust oil grease efflorescence and applying @ of 1 liter for 2 sqm. |
| 69 | Rumble Strips (Provision of 15 nos rumble strips covered with MSS bituminous carpet, 15-20 mm high at center, 250 mm wide placed at 1 m center to center at approved locations to control speed, marked with white strips of road marking paint.) unit is Sqm |
| 70 | Rumble Strips - Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. Unit is Sqm |
| 71 | Add 1% Labour Cess |
| 72 | Add 18% GST |
| 73 | Add 10% Seigniorage Fee |
| 74 | Maintainance for 1st year |
| 75 | Maintainance for 2nd year |
| 76 | Maintainance for 3rd year |
| 77 | Maintainance for 4th year |
| 78 | Maintainance for 5th year |
| 79 | Add 1% Labour Cess |
| 80 | Add 18% GST |
| 81 | Add 10% Seigniorage Fee |
| 82 | Dhar Paswan ke gharto Bishar Asthan Reo Road tak Via Agan Badi - Setting out(i) Construction of Reference & Working Benchmark = 1 Nos. & 1 Nos. RespectivelySOR Item No.-1.16 |
| 83 | (ii) Construction of Reference Pillars/Burjees = 6 NosSOR Item No.-1.16 |
| 84 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.SOR Item No.-2.2 |
| 85 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 1000 m as per Technical Specification Clause 301.5SOR Item No.-3.4 |
| 86 | Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5m transporting to site, spreading grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead up to 100 m as per Technical Specification Clause 301.5SOR Item No.-3.5 (ii) |
| 87 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 100 m as per Technical Specification Clause 303.1.SOR Item No.-3.14 |
| 88 | Construction of granular sub-baseby providingwell gradedmaterial (Grading I) , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with threewheel 80-100 kN static roller capacity to achieve thedesired density, complete as per Technical Specification Clause 401SOR Item No.-4.1.401(Aii) |
| 89 | WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smoothwheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.80 -100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.SOR Item No.-4.7 (3)(A) |
| 90 | Prime Coat Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502SOR Item No.-5.1 (i) |
| 91 | Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1)using emulsiondistributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 50SOR Item No.-5.2 (iii) 503 |
| 92 | Mix Seal Surfacing (Waste Plastics) By Mechanical Means (Type-B) Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509SOR Item No.-5.11 |
| 93 | Earthwork excavation for foundation of structures as per drawing and teachnical specification clause 1104 includding setting out, stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved matefial . (A)Ordinary soilSOR Item No.-11.1 (I) |
| 94 | Providing concrete for plain/reinforced concrete in opne foundations complete as per drawwings and technical specifications clause 802,803,1202&1203(I) PCCGrade M-10 Nominal mix 1:2.5:5 with 40mm and down graded metelSOR Item No.-11.4(II) (i) |
| 95 | Providing concrete for plain/reinforced concrete in opne foundations complete as per drawwings and technical specifications clause 802,803,1202&1203(I) PCCGrade M-15 Nominal mix 1:2.5:5 with 40mm and down graded metelSOR Item No.-11.4(II) (i) |
| 96 | Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204P.C.C grade M 15 |
| 97 | Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Cllauses 1002,1010 and 1202 (8.10 + 4.84)SOR Item No.-13.2 |
| 98 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 1204.3.8SOR Item No.-12.10 |
| 99 | Providing weepholes in brick masonry/stone mosonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification clauses 616,709,1204.3.7SOR Item No.-12.90 |
| 100 | RCC GRADE M-25 Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 and 1204 |
| 101 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 @@ 100 kg/cum of RCC + 80 kg/cum of PCC of cutoff wall |
| 102 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smallersize towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specificationClause 1204.3.8 |
| 103 | Drainage spouts complete as per drawing and technical specifications clause 1209SOR Item No.-13.10 |
| 104 | RCC M-25 Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 |
| 105 | Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000mm as per drawing and technical specifications Clauses 800, 900 and 1208.3 |
| 106 | Bedding for Type - B PCC(M20) Bedding Laying (First Class ) bedding concrete as per clause 1105 (ii)SOR Item No.-9.2 |
| 107 | Dismantling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202. By Manual Means Plain Cement Concrete SOR Item No.-2.5 I (B) |
| 108 | Dismantling of Structures Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specification Clause 202. By Manual Means Rubble stone masonry in cement SOR Item No.-2.5 III (B) |
| 109 | Removing all types of Hume pipes and stacking within a lead of 1000 m including Earthwork and Dismantling of Masonry Works as per Technical Specification Clause 202. Upto 600 mm dia Hume pipeSOR Item No.-2.13 A |
| 110 | Providing and laying reinforced cement concrete pipe NP4 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapaets clause 1106. SOR Item No.-9.3(C) |
| 111 | Kilometre Stone Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 SOR Item No.-(I)(II) Ordinary Kilometer Stone (Pre-cast) |
| 112 | Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704At outer side of H-Curve & @ 1.50m c/c both side at heigh embankment SOR Item No.-10.11 |
| 113 | Providing and fixing of typical MMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges.The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level.The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube.All M.S. will be stove enameled on both sides.Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour.All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 SOR Item No.-10.16 |
| 114 | Maintenance Board |
| 115 | MMGSY Logo Board |
| 116 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1)(ii) 600 mm equilateral triangle |
| 117 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as perdrawings and Technical Specification Clause 801 SOR Item No.-10.2 A (1) (v) 600 mmx 450 mm rectangular |
| 118 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. SOR Item No.-8.13 |
| 119 | Rumble Strips (Provision of 15 nos rumble strips covered with MSS bituminous carpet, 15-20 mm high at center, 250 mm wide placed at 1 m center to center at approved locations to control speed, marked with white strips of road marking paint.) unit is Sqm |
| 120 | Rumble Strips - Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 . The finished surface to be level , uniform and free from streaks and holes. Unit is Sqm |
| 121 | Planting of Trees and their Maintenance for one Year Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one |
| 122 | Add 1% Labour Cess |
| 123 | Add 18% GST |
| 124 | Add 10% Seigniorage Fee |
| 125 | Maintainance for 1st year |
| 126 | Maintainance for 2nd year |
| 127 | Maintainance for 3rd year |
| 128 | Maintainance for 4th year |
| 129 | Maintainance for 5th year |
| 130 | Add 1% Labour Cess |
| 131 | Add 18% GST |
| 132 | Add 10% Seigniorage Fee |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
