To Provide Safety Measures By Fabrication And Fixing Various Allied Works On Emergency Basis At Bharatratna Dr. Babasaheb Ambedkar Mun. Gen. Hospital, Kandivaliwest, In Rs Ward.- 1 PVC Telephone Cable – 50 pair R3-ME-12-2-e 2 SITC of Push Button telephone instrument desktop / wall mount unit R3-ME-12-1-k 3 Providing and fixing G.I. crimpedwire meshofrequiredopenings of size 25 mm x25 mm or of any size with main and cross wires of 10gauge approved type as per manufacture’s specifications with necessary fittings including painting with one coat of one coat of red oxide zinc chromate primer and two coats of approved synthetic enamal paint etc. completeasdirectedby Engineer In Charge. (Iron works will be paid separately. The clearvisibleareaofthewire mesh exclusive overlap will be paid for).R3-CS-SS-14 4 Providing and fixing aldrops of 16 mm diameter bars manufactured as per IS:2681-1991, wherever they apply for doors and windows with necessary materials and labour etc. complete, 300 mm long R3-CS-HW-06-d-2 5 Providing and fixing double / single acting spring hinges as described below manufactured relevant standards for doors with all labour, materials and necessary fixtures etc. complete, 150 mm long. R3-CS-HW-10-a-3 6 Exhaust fan of 305mm sweep, 900/1400RPM, with 750 CFM free air delivery, AC 230V/415V , 50 Hz, single phase / three phase complete with all necessary accessories forcompleting installation.R3-ME-4-12-I 7 Providing, detailing, fabricating and fixing at desired location using hot rolled sections and MS Plates of grade Fe 250 as per specifications and approved fabrication drawings (which are to be prepared by Contractor and got approved from Engineer), transporting to site and erecting structural steel members for all heights & at all levels including provision of necessary erection bolts, fixing bolts, nuts, washers, cleats, stiffeners, gussets, base plate, and all necessary fixtures and operations like preheating as per specifications, straightening, bending, cutting, drilling, grinding, machining if specified, welding, grinding and removing the welding burr and preparing surface for painting with wire brush cleaning and applying two coats of epoxy red oxide zinc phosphate primer of 30 microns each and two coats of Epoxy Corrosion Resistant Enamel paint of 30 microns after fabrication including touching up with spray painting after erection etc complete as directed by Engineer In Charge. (The qty. for this item shall be measured for gusset plates, base plates, bolts in M.T.) R3-CS-SS-01 8 Point wiring by using PVC insulated copper conductors (alongwith same size of pvc insulated copper conductor for earthing & 3 plate ceiling rose) : PVC conduit concealed with modular switches & FR wires. (SP-ME-TS- 12) Light /Fan / Ex. fan Points Concealed Manner with Modular switches & FR wires R3-ME-3-13-a 9 Providing and fixing in position aluminum folding door fully panelled with 6mm thk. Novapan BSL and made up of extruded and anodised aluminium sections of approved make and of size 63.5 mm x 38.10 mm x 2.0 mm thk (wt. 1.054 kg/Rm) for outer frame, 47.62 mm x 10.16 mm x 1.74 mm thk (wt. 0.881kg/Rm) for top rail, 95.25 mm x 25.40 mm x 2.0 mm thk(wt. 1.519 kg/Rm) for bottom rail, 25.0 mm x 44.45 mm x 2.40 mm thk (wt. 0.918 kg/Rm) for lock rail, 47.62 mm x 44.45 mm x 1.8 mm thk (wt. 0.943kg/Rm) for shutter vertical hinges side, 47.62 mm x 44.45 mm x 1.95 mm thk (wt. 0.936 kg/Rm) shutter vertical latch side, clip weighing 0.097 kg/Rm including neoprene gasket, fixtures, fastenings and accesories like hinges, locking arrangement, door closer etc. complete as directed by Engineer In Charge. (Note: anodic film must not be less than 15 microns i.e. AC-15 as per IS, the anodizing must be scaleted by keeping the anodized section in boiling de-anodized water for a period of one hour) R3-CS-AW-13 10 Providing and Fixing MS Safety grill of weight specified below for windows as per design including fabricating the grill using M.S. square / round bar, flats and angles including painting with one coat of red oxide zinc chromate primer and two coats of synthetic enamel paint of approved colour and brand etc complete as directed, Grill weighing 20 to 25 kg / sqm R3-CS-SL-12-c 11 Revolving Patient Stool - Type: Revolving Patient StoolMaterial: Stainless steel top, stainless steel frameBase: Four legsSeat Height Adjustment: 18-23 inchesSeat Diameter: 16 inchesWeight Capacity: 250 lbsCasters: Smooth-rolling
