Urban Local Bodies has published Tender For Beautification And Naming Of The Park At Model Town Pehowa As Neta Ji Ishwar Dayal Garg Park Mc Pehowa. Submission Date for this Tender is 27-03-2024. Gardening Tenders in pehowa Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | [10.1]Providing and laying of base course of floors consisting of 100 mm thickcement1:8:16and100mmsandor stone filling. |
| 2 | [10.50.1]Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 1. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 3 | [10.51]Providing and fixing granite stone in all shades 15mm to 18 mm thickin skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade ofGranite including labour for fixing cramps pins and dowels etc. |
| 4 | [10.8]Providing and laying of conglomerate floor 40mm thick cement concrete topping 1:2:4 |
| 5 | [11.5.4]12 mm cement plaster of mix : 4. 1:6 (1 cement: 6 fine sand) |
| 6 | [11.6.1]15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) |
| 7 | [11.64.1]Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 8 | [11.72.2]Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : 2. Two coats |
| 9 | [11.9.1]15 mm cement plaster on rough side of single or half brick wall of mix: 1. 1:4 (1 cement: 4 coarse sand) |
| 10 | [12.158.1]Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. 1. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 11 | [13.29.2]Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 12 | [13.3.1.1]Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 1.1. Profile B Fixing with adjustable lugs with split end tail to each jamb |
| 13 | [13.41]Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 14 | [20.71.1]Supply, erection, testing of Ceiling fansIS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge 1. 48" (1200mm) |
| 15 | [20.72]Supplying, errection, testing of Exhaustfan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structureconfirming to latest IS specificationscomplete in all respect to satisfaction of Engineer-in-charge. |
| 16 | [22.1.3]Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 3. White vitreous chinaware Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 17 | [22.103.1]Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1. 15 mm nominal bore |
| 18 | [22.105.1]Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 1. 15 mm nominal bore |
| 19 | [22.107.1]Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1. 15 mm nominal bore |
| 20 | [22.122.1]Providing and fixing PTMT urinal cock of approved quality and colour. 1. 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms |
| 21 | [22.124.3]Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 3. 25 mm nominal bore, 152mm long, weighing not less than 440 gms |
| 22 | [22.14.2.1]Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 2.1. Flexible pipe 32 mm dia |
| 23 | [22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 24 | [22.210.4]Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 4. Rectangular shape 1500x450 mm |
| 25 | [22.22.1]Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1. White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 26 | [22.23.1]Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 1. W.C. pan with ISI marked white solid plastic seat and lid |
| 27 | [22.39.1]Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 1. 10 litre capacity - White |
| 28 | [22.44]Providing and fixing 32 mm diameter Gl. extension pipe for Indian type Water Closet suite complete with accessories(as approved by the Engineer -in-charge) |
| 29 | [22.50.1.1.1]Providing and fixingpartitions for different type of urinals. 1.1.1. Vitreous Chinaware Partition plate. Small size 680mm x 330 mm White |
| 30 | [22.81.2]Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 2. 75 mm dia |
| 31 | [22.87.3]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings This includes jointing of pipes and fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge. External work 3. 25 mm nominal outer dia Pipes |
| 32 | [23.22.1.4]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.4. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 125 to 160 Amp, 25 KA |
| 33 | [23.22.2.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 2.1. MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings MCCB up to 125 A FP |
| 34 | [23.3.6.7]COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS) 6.7. Wiring main and sub mains in twosingle core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 2 run of Size 2.50 Sqmm(1.1.80mm) |
| 35 | [23.7.1.1]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 1.1. PVC CONDUIT and MS/GIBOX only for LIGHT/FAN/Call bell point wiring Group A |
| 36 | [23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. |
| 37 | [23.8.1.12]FITTING AND ACCESSORIES 1.12. Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Bakelite angle/straight button holder large size. |
| 38 | [23.8.11.1]FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch |
| 39 | [23.8.11.4]FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket |
| 40 | [23.8.3.3]FITTING AND ACCESSORIES 3.3. Supply and erection of suitable MS/GI Box covered with 5 mm thick Bakelite sheetas below 180 mm X 100 mm X 60 mm deep M.S. Box |
| 41 | [24.10.1]CIVIL ITEMS (USED COMMONLY IN ELECTRICAL WORKS) 1. Digging & refilling of trench 30 cm wide below ground level for erection of pipe/cable (up depth of 1 Metre. underground cable excluding the cost of cable/pipe complete in all respect. |
| 42 | [24.5.1.2]MISCELLANEOUS ITEMS 1.2. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 2.5 sqmm |
| 43 | [24.5.2.1]MISCELLANEOUS ITEMS 2.1. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 40/32 mm outer dia/ inner dia |
| 44 | [24.8.1]RCC FOUNDATIONS FOR OCTAGONAL POLES 1. Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 3m high pole |
| 45 | [28.39]Water proofing of roof terraces, Basements, Retaining Walls, Water tanks etc with Zydex Zycoprime / Elastobar / Equivalent solution so as to form a water-resistant cementitious bonding coat and to form on-site seamless cross-linked elastomeric membrane on the concrete surface to reduce its porosity. Creating a cementitious elastomeric polymeric membrane of 2 coats of Elastobar and Zycoprime/Equivalent after application of Zycosil and Zycoprime Solution in New Construction. Take equal parts of Elastobar and Cement and form a paste. Add little water to the paste to make it brush able. Apply the paste on surface with brush. Leave the surface for drying for at least 4 - 6 hours to getelastomeric membrane. After this application, make one more layer of rough cementitious membrane using mixture of 1 Part of Zycoprimeplus1 Part of Cementplus1 Part of fine sand. Apply paste on the surface with a brush to make a rough texture. Now your surface is ready to bond well with tiles/screed. |
| 46 | [4.14.1]Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil. |
| 47 | [6.1.2]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 48 | [6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 49 | [6.14.1]Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 50 | [6.16]Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 51 | [6.30.1]Centering and shuttering including strutting, propping etc. and removal of form for 1. Foundations, footings, bases of columns, etc. for mass concrete |
| 52 | [6.30.3]Centering and shuttering including strutting, propping etc. and removal of form for 3. Suspended floors, roofs, landings, balconies and access platform |
| 53 | [6.30.5]Centering and shuttering including strutting, propping etc. and removal of form for 5. Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 54 | [6.30.6]Centering and shuttering including strutting, propping etc. and removal of form for 6. Columns, Pillars, Piers, Abutments, Posts and Struts |
| 55 | [6.33.3]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level 3. Cold twisted bars |
| 56 | [7.20.1]Brick work with common burnt clay modular bricks of class designation 10.5 in foundation and plinth in: 1. Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 57 | [7.22.1]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 1. Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 58 | [9.14.1]Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 1. With common burnt clay non-modular brick tiles of class designation 10 |
| 59 | [9.17.1]Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 1. In 75x75 mm deep chase |
| 60 | [9.18]Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 61 | [9.47.3]Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main `T` runner with suitably spacedjoints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross `T` of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main `T` at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross `T` of length 600 mm and size 24x25 mm made of0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main `T` runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 3. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 62 | [9.57.3]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 3. 150 mm diameter |
| 63 | Supply and fixing of 40 watt tube light(MAKE-WIPRO,SYSKA,PHILIPS,ORIENT) |
| 64 | Earth filling with a lead of 10 km including loading unloading and shifting complete in all respect |
| 65 | Ring 12 feet dia SS 304 fabrication,water pattern using multiple clea tream nozzles mounted on a single ring.The direction adjustment o he nozzles can create various effects such as inward crown,outwarc crown,vertical crown,inward Weave or outward weave.To be installed n a way that the ring is either embedded in the civil structure or it below the water and individual nozzle are visible above the water Make reliable |
| 66 | Ring 8 feet dia SS 304 fabrication,water pattern using multiple clea stream nozzles mounted on a single ring.The direction adjustment of the nozzles can create various effects such as inward crown,outward crown,vertical crown,inward Weave or outward weave.To be installed in a way that the ring is either embedded in the civil structure or is below the water and individual nozzle are visible above the water. Make reliable |
| 67 | Straight jet nozzlesDescription -Smooth bore single clear stream jet with adjustabledirection.Normally used in groups to form a circle or straight line of jets.Sizes -Available from 12mm to 50mm inlet sizes with a variety of bore sizes.Custom -Custom inlets,or threads are possible.Type - Water level independent (no change in water effect with varying water level)brass chrome plated make reliable décor |
| 68 | 3 Sut Gate Valve Brass Chrome Plated The handle of the Brass Ball Valve lies flat in alignment with the flow when open.Can Handle High Pressure and Temperature (Working temperature -10 to 100 deg C). Application:Water/Gas/Oil.Thread Ends Comply Per ANSI B1.20.1. Full Port.Rated Pressure Bar 40 Bars. |
| 69 | SS Nipple and Sockets Corrosion Free Make Reliable Decor |
| 70 | Submersible pump open well 3.0 hp Three Phase Minimum varlations in efficlency during entire operating range Increases the utility of pumpset for varlable conditions.The motor is designed to withstand wide voltage fluctuations from 350 to 440 volts and reduces motorburning in case of low voltage.Protection:IP 44/IP 55,Sync Speed. 3000 rpm.Make Kirlosekar |
| 71 | Submersible pump open well 5.0 hp Three Phase Minimum varlations in efficlency during entire operating range increases the utility of pumpset for varlable conditions.The motor is designed to withstand wide voltage fluctuations from 350 to 440 volts and reduces motorburning in case of low voltage.Protection:IP 44/IP 55,Sync Speed-3000 rpm.Make Kirlosekar |
| 72 | Underwater light (DMX controlled)(warm white)/RGB IP 6818valt DC shockproof make by reliable decor Epoxy encapsulated compression type cable entry glands for complete water protection.Noryl body for 100%corrosion free life even in seawater applications.Make reliable décor,make premium Low Voltage for safety.And shockproof.MakeReliableDécor |
| 73 | SS Underwater light Stand Corrosion Free Make Reliable Décor |
| 74 | Drives for Underwater Light programmer make reliable décor |
| 75 | SS Screen good filter These filters provide large filtration capacity for residential,commercial,and municipal drip applications.This meansess cleaning and lower maintenance costs.The filter body and cover are made of high impact thermal plastic.Make Reliable decor |
| 76 | Sequencing Control panel operating for each pump hp Electrical pane cubical type wall /floor mounted the panel shall be fabricated out of 2.0 mm thick CRCA MS sheet,duly stove enameled with synthetic paint of approved shade over a coat of red oxide primer.(all accessories are of reputed make)i./c MCBs,main switches change overs etc.as per requirements.Contractor,rely Protection from:1)Motor Overloads- Pump Protection for when the pump motor current is above its Full Load Amp rating.2)Temperature Sensors-Pump Protection when the pump or motor are above their Temperature rating.3)Level Sensors-Pump control and protection to insure the pump doesnand#39:t run dry.4) Flow Sensors-Used to verify the pump is moving fluid 5)Pressure Sensors-Used for pump control and to adjust speed Make reliable décor,make premier |
| 77 | Installation Charges: Pluming Charges:-Installation 2”,1`pipe,union elbow with fitting charges Necessary plumbing work such as pipes finolex /prince/supreme)andsuitable for the respective,working pressure with allfitting coupling,tee,bends ,Reducers,bushes,male andfemale threads ,screwed Adopter etc ,joining with solvent chemicals. (Material with Installation) |
| 78 | Electric fitting to Connecting starter andlight Wiring,Installation of Underwater Light on Water distributer with Necessary Wiring,Taping Joints of wiring,Connecting light wiring with Underwater Light Programmer and Control Panel.(Installation with Material |
| 79 | FRP Floater Setup 4.5 ft dia with 12 mm FRP Finish layer.Made of high Quality FRP Material.Natural abstract FRP with underwater RGB 8 colored light highly effected grace at night.Fire resistance,shock proof light,DC Operating Lights,Highly Durable |
| 80 | Sand Fiiter Fibreglass Top Mount 500 mm dia Capacity Per Hr Turnover:10800LValve:50mm Max operating pressure:36 psi /2.5 bar Max temperature of 43?(109*F) Sand Reguired:85 Kg Make Emauy |
| 81 | Motor pump 1HP 220V/50Hz,Single phase ”Flange,IPx5 Waterproof standard,Ring Lock design,Testing Pressure 50PSI (3.5 Bar),Waterflow:19m³/hr,S S316 Shaft andMechanical SealMake Emaux |
| 82 | Sand media (For Sand Filter)A sand media filed with silica sand or crushed granite.Contaminants are filtered from the water as it flow through the filtering media.Multiple tanks of sand media are used to obtain sufficient filtration at the design flow rate of the Swimming Pool 0.3-0.6 mm Size Sand media |
| 83 | Floor Inlet 2`for concrete Pool UV Resistance and better grade of ABS used gives longer life span.Different options of fitment (e.g)Press fit in 1.5”PVC pipe,2`.FTR or Pentair standard wall conduit gives freedom of installation to installer.Adjustability gives options to vary the flow as required in different sizes of pools MakeEmaux |
| 84 | Installation/Plumbing Chargers:Plumbing 2”,1.5`pipe PVC union valve,elbow with fitting charges Necessary plumbing work such as pvc pipes (finolex/prince/supreme)andsuitable for the respective,working pressure with all fitting coupling,tee,bends,Reducers,bushes,male and female threads,screwed Adopter etc,joining with solvent chemicals(Including Material) |
| 85 | Providing and fixing of multi play station with complete in all respect |
| 86 | Providing and fixing arch swing (air spring double) with complete in all respect |
| 87 | Providing and fixing of spring rider duck with complete all respect |
| 88 | Providing and fixing of sea saw single with complete all respect |
| 89 | Blue and green rectangular park plastic dustbin, for outdoor |
| 90 | S/E Of 10 watt led decorative post top fixture fitting made corrosion resistant dia cast aluminium inner dia 76mm decorative aluminium hat is also ussed rubber gas kits are provided at appropirate location for dust and water protection diffuser is is made in |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
