|
| 1 | Allen Key set of 12 pieces |
| 2 | Pliers combination |
| 3 | Spanner D.E. set of 12 pieces |
| 4 | Spanner, ring set of 12 |
| 5 | Spanners socket with speed handle, T-bar, ratchet and universal set of 28 pieces with box |
| 6 | Steel rule |
| 7 | Steel tool box with lock and key (folding type) |
| 8 | Wire cutter and stripper |
| 9 | Adjustable spanner (pipe wrench) |
| 10 | Air blow gun with standard accessories |
| 11 | Ammeter DC with external shunt |
| 12 | Air ratchet with standard accessories |
| 13 | Air impact wrench with standard accessories |
| 14 | Anvil with Stand |
| 15 | Battery –charger |
| 16 | Blow Lamp |
| 17 | Belt Tensioner gauge |
| 18 | Caliper inside with Spring |
| 19 | Calipers outside with spring |
| 20 | Car Jet washer with standard accessories |
| 21 | Chain Pulley Block capacity with tripod stand |
| 22 | Chisels cross cut |
| 23 | Circlip pliers Expanding and contracting |
| 24 | Clamps C |
| 25 | Clamps C |
| 26 | Clamps C |
| 27 | Compression testing gauge suitable for diesel Engine with standard accessories |
| 28 | Connecting rod alignment fixture |
| 29 | Copper bit soldering iron |
| 30 | Cylinder bore gauge capacity |
| 31 | Cylinder liner- Dry & wet liner, press fit & slidefit liner |
| 32 | DC Ohmmeter |
| 33 | Depth micrometer |
| 34 | Dial gauge type 1 Gr. A (complete with clamping devices and with magnetic stand) |
| 35 | Different type of Engine Bearing model |
| 36 | Different type of piston model |
| 37 | Dividers with Spring |
| 38 | Drift Punch Copper |
| 39 | Drill point angle gauge |
| 40 | Drill twist (various sizes) |
| 41 | Electric Soldering Iron |
| 42 | Electric testing screw driver |
| 43 | Engineer’s square |
| 44 | Feeler gauge 20 blades (metric) |
| 45 | File, Square |
| 46 | Files assorted sizes and types including safe edge file (20 Nos.) |
| 47 | Flat File , second cut |
| 48 | Flat File , bastard |
| 49 | Fuel feed pump for Diesel |
| 50 | Fuel injection pump dismantling tool kit /Universal Vice |
| 51 | Grease Gun |
| 52 | Grease Gun heavy duty trolley type |
| 53 | Growler |
| 54 | Hacksaw frame |
| 55 | Hammer Chipping |
| 56 | Hammer copper with handle |
| 57 | Hammer Mallet |
| 58 | Hammer Plastic |
| 59 | Hand operated crimping tool |
| 60 | Hand reamers adjustable |
| 61 | Hollow Punch set of seven pieces |
| 62 | Injector – Multi hole type, Pintle type |
| 63 | Left cut snips |
| 64 | Lifting jack screw |
| 65 | Magneto spanner set with 8 spanners |
| 66 | Magnifying glass |
| 67 | Marking out table |
| 68 | Multimeter digital |
| 69 | Oil pump for dismantling and assembling. |
| 70 | Oscilloscope |
| 71 | Outside micrometer |
| 72 | Outside micrometer |
| 73 | Outside micrometer |
| 74 | Outside micrometer |
| 75 | Philips Screw Driver set of 5 pieces |
| 76 | Pipe flaring tool |
| 77 | Piston ring compressor |
| 78 | Piston Ring expander and remover. |
| 79 | Piston Ring groove cleaner. |
| 80 | Prick Punch |
| 81 | Punch Letter 4mm (Number) |
| 82 | Radiator cut section-cross flow |
| 83 | Radiator cut section-down flow |
| 84 | Radiator pressure cap |
| 85 | Right cut snips |
| 86 | Rivet sets snap and Dolly combined |
| 87 | Scraper Triangular |
| 88 | Scriber with scribing black universal |
| 89 | Sheet Metal Gauge |
| 90 | Soldering Copper |
| 91 | Spanner Clyburn |
| 92 | Spark lighter |
| 93 | Starter motor axial type, pre-engagement type & Co-axial type |
| 94 | Steel rule 15 cm inch and metric |
| 95 | Straight edge gauge 2 ft. |
| 96 | Straight edge gauge 4 ft. |
| 97 | Stud extractor set of 3 |
| 98 | Stud remover with socket handle |
| 99 | Surface gauge with dial test indicator plunger type |
| 100 | Taps and Dies complete sets (5 types) |
| 101 | Taps and wrenches - Metric |
| 102 | Temperature gauge with sensor |
| 103 | Thermostat |
| 104 | Thread pitch gauge Metric |
| 105 | Timing lighter |
| 106 | Torque wrenches |
| 107 | Trammel |
| 108 | Tyre pressure gauge with holding nipple |
| 109 | Vacuum gauge |
| 110 | Valve Lifter |
| 111 | Vernier caliper |
| 112 | Water pump for dismantling and assembling |
| 113 | Dual Magnetization Yoke |
| 114 | Grinding machine (general purpose) D.E. pedestal with 300 mm dia. wheels rough and smooth |
| 115 | Chisel cold |
| 116 | scriber |
| 117 | File flat |
| 118 | Steel measuring tape |
| 119 | Plier flat nose |
| 120 | Centre Punch |
| 121 | Electrician Screw Driver |
| 122 | Hammer Ball peen with Handle |
| 123 | Hand filesSecond cut Flat |
| 124 | Screw Driver |
| 125 | Screw Driver |
| 126 | Angle plate adjustable |
| 127 | Angle plate size |
| 128 | File, half round second cut |
| 129 | File, triangular second cut |
| 130 | Glow plug tester |
| 131 | Granite surface plate with stand and cover |
| 132 | Hand Shear Universal |
| 133 | Hand Vice |
| 134 | High rate Discharge tester(Cell Tester) |
| 135 | Insulated Screw driver |
| 136 | Insulated Screw driver |
| 137 | Oil Stone |
| 138 | Pliers round nose |
| 139 | Pliers side cutting |
| 140 | Portable electric drill machine |
| 141 | Set of stock and dies-Metric |
| 142 | Spanner, adjustable |
| 143 | Tachometer |
| 144 | Telescopegauge |
| 145 | V \" Block pair with clamps |
| 146 | Voltmeter |
| 147 | Arbor press hand operated |
| 148 | Working model of Power windows |
| 149 | Hydrometer |
| 150 | Hand operated crimpingtool/wire |
| 151 | Engineers stethoscope |
| 152 | Discrete component trainer discrete componentwith regulated power supply |
| 153 | Suitable work table with vices |
| 154 | Discussion Table |
| 155 | Fire Extinguisher |
