|
| 1 | Part A :- PUMPING MACHINERY At Headworks and Water Treatment Plant Dismantling & overhauling of 90 HP Vertical Turbine pumps from the position with cleaning, checking, aligning, assembling i.e., refitting, commissioning with trial run on no load & full load for at least 30 minutes including replacement of spare parts, fastners etc. complete as per site requirements. |
| 2 | Complete Repairs to 90 HP VT Pump including all spares required including all material and labour etc. complete with test & trial. |
| 3 | Servicing and overhauling of 90 HPmotors, including removing from location, dismantling cleaning the winding, drying, applying, varnish, baking, changing the bearing if necessary greasing the bearing, assembling, and giving satisfactory trials on No load and full load etc. |
| 4 | Providing, erecting Pressure gauge Bourdon\"s type of 100 mm dia. as per IS 3624:1987 of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I.Pipe. Pressure gauge shall be installed as directed,with tapping on rising main. Mounting - Direct bottom, Stainless Steel body, Toughened glass window. |
| 5 | Providing & erecting 3 Pole MCCB 415V, 400/500A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure /panel as per specification no. SW-SWR/MCCB. |
| 6 | Supplying and erecting of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity 99.9% aluminium purity with E91E Grade as per IS 5082 & Current Density 0.8 A per sq. mm. with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCPBB. |
| 7 | Providing erecting and giving test and trial of Fully Automatic, Auto Transformer Starter with Air Break Contactor, assembled locally with contactors of approved make in 14 SWG sheet steel fabricated, floor mounted type cubical panel, suitable for operation on 380 - 440 Volts, 3 Phase, 50 Hz, fitted with accessories as below. The incoming and outgoing cable end boxes shall be on either sides of main panel. The cable entries from auto transformer shall be totally enclosed in sheet metal. The starter shall have screened louvers on both sides. Cubical Panel Size 1.25 m height X 0.75 m width X 0.45 m deep Starter for Motor HP / Contactor Rating \" Main/ Start/ Run\"90/100 HP (200 / 110 / 110) |
| 8 | Supplying & erecting HRC fuse cartridge 415V, 300A |
| 9 | Internal wiring of LT panel including all material & labour. |
| 10 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 11 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 12 | Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP |
| 13 | Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification No EA-EP. |
| 14 | Dismantling & overhauling of 30 HP Centrifugal pumps from the position with cleaning, checking, aligning, assembling i.e., refitting, commissioning with trial run on no load & full load for at least 30 minutes including replacement of spare parts, fastners etc. complete as per site requirements. |
| 15 | Complete Repairs to 30 HP Centrifugal pumps including all spares required including all material and labour etc. complete with test & trial. |
| 16 | Servicing and overhauling of 30 HPmotors, including removing from location, dismantling cleaning the winding, drying, applying, varnish, baking, changing the bearing if necessary greasing the bearing, assembling, and giving satisfactory trials on No load and full load etc. |
| 17 | Rewinding of 30 HP electric motor three phase up to 1400 RPM of all types and makes with copper wire, overhauling with minor repairs, lubricating of ball bearings & bush bearing, and replacing screws etc. testing for the original speed and no load consumption with guarantee for one year. |
| 18 | Providing, erecting Pressure gauge Bourdon\"s type of 100 mm dia. as per IS 3624:1987 of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I.Pipe. Pressure gauge shall be installed as directed,with tapping on rising main. Mounting - Direct bottom, Stainless Steel body, Toughened glass window. |
| 19 | Supplying and erecting bank of All Polypropylene capacitors with the standard capacities of 1, 2, 3, 5, 7, 12.5, 15, 20 and 25 KVAR units of power factor correction for operation on 3 phase, 50 Hz, 400 V+/- 10% with externally discharging resistances, earthing terminals and built on angle iron or and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested. |
| 20 | Providing erecting and giving test and trial of Fully Automatic, Auto Transformer Starter with Air Break Contactor, assembled locally with contactors of approved make in 14 SWG sheet steel fabricated, floor mounted type cubical panel, suitable for operation on 380 - 440 Volts, 3 Phase, 50 Hz, fitted with accessories as below. The incoming and outgoing cable end boxes shall be on either sides of main panel. The cable entries from auto transformer shall be totally enclosed in sheet metal. The starter shall have screened louvers on both sides. Cubical Panel Size 1.25 m height X 0.75 m width X 0.45 m deep Starter for Motor HP / Contactor Rating \" Main/ Start/ Run\"30 HP (110 / 40 / 40) |
| 21 | Supplying & erecting HRC fuse cartridge 415V, 100A |
| 22 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 23 | Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP |
| 24 | Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification No EA-EP. |
| 25 | Dismantling & overhauling of 100 HP Vertical Turbine pumps from the position with cleaning, checking, aligning, assembling i.e., refitting, commissioning with trial run on no load & full load for at least 30 minutes including replacement of spare parts, fastners etc. complete as per site requirements. |
| 26 | Complete Repairs to 100 HP VT Pump including all spares required including all material and labour etc. complete with test & trial. |
| 27 | Servicing and overhauling of 100 HPmotors, including removing from location, dismantling cleaning the winding, drying, applying, varnish, baking, changing the bearing if necessary greasing the bearing, assembling, and giving satisfactory trials on No load and full load etc. |
| 28 | Rewinding of 100 HP electric motor three phase up to 1400 RPM of all types and makes with copper wire, overhauling with minor repairs, lubricating of ball bearings & bush bearing, and replacing screws etc. testing for the original speed and no load consumption with guarantee for one year. |
| 29 | Providing, erecting Pressure gauge Bourdon\"s type of 100 mm dia. as per IS 3624:1987 of required range complete with syphon tube, isolating cock suitable for 12 mm dia G.I.Pipe. Pressure gauge shall be installed as directed,with tapping on rising main. Mounting - Direct bottom, Stainless Steel body, Toughened glass window. |
| 30 | Supplying, installing, testing and commissioning air circuit breaker manual fixed type, non-drawout type, 650V, 800A, rated at 50º C without deration, 12kV Impulse, 4 pole (100% Neutral Protection), 50 kA (Ics=Icu=Icw for 1s), with standard accessories with ready to close, individual fault trip, alarm and trip indications, mechanical and electrical anti pumping, soft/ hard rating plug (including hard rating plug CT) with Micro-processer based LCD display release with LSIG and temperature rise protection & with 4 C/O contacts for On-Off-Trip indication, min. 5 event and trip history on breaker display on provided iron frame as per specification no. SW-SWR/ACB. |
| 31 | Supplying and erecting bank of All Polypropylene capacitors with the standard capacities of 1, 2, 3, 5, 7, 12.5, 15, 20 and 25 KVAR units of power factor correction for operation on 3 phase, 50 Hz, 400 V+/- 10% with externally discharging resistances, earthing terminals and built on angle iron or and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested. |
| 32 | Supplying and erecting of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity 99.9% aluminium purity with E91E Grade as per IS 5082 & Current Density 0.8 A per sq. mm. with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCPBB. |
| 33 | Part B :- Electrification Works At Headworks and Water Treatment Plant Building Premicess Supplying and erectingPVCtrunking (PVCcasing-n-capping)ofsize25 mm. with accessorieson wall/ceiling as per specification No: WG-MA/CON. |
| 34 | Supplying & erecting mains with 2x1.5 sq.mm. FRLSH copperPVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 35 | Supplying & erecting mains with 1x1.5 sq.mm. FRLSH copperPVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 36 | Supplying & erecting mains with 2x2.5 sq.mm. FRLSH copperPVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 37 | Supplying & erecting mains with 1x2.5 sq.mm. FRLSH copperPVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 38 | Supplying and erecting mains with ISI mark WP 2 x 4 sq. mm.1100 V grade aluminium PVC insulated and PVC sheathed wires on G.I. bearer wire No. 8 SWG complete erected with required size of porcelain reel insulators and 16 SWG G.I.binding wire. |
| 39 | Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete. |
| 40 | Supplying and erecting modular type switch 16Aduly erected on provided plate and box with wiring connections complete. |
| 41 | Supplying and erecting modular type 3 pin 6Amulti socket safety shutter duly erected on provided plate and box with wiring connections complete. |
| 42 | Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter duly erected on provided plate and box with wiring connections complete. |
| 43 | Supplying and erecting PVC Surface modular switch box with double mounting plate for 4module duly erected. |
| 44 | Supplying and erecting PVC Surface modular switch box with double mounting plate for 8module duly erected. |
| 45 | Supplying and erecting PVC Surface modular switch box with double mounting plate for 12module duly erected. |
| 46 | Point wiring for light/ fan/ bell in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW |
| 47 | Wiring for plug on board with flush switch socket, copper wiring and earthing as per specification No:WG-PW/SW |
| 48 | Supplying and erecting Street light bracket for erection of side entryfitting on pole with 40 mm. dia. ‘B’ grade G.I. pipe of required length complete as per specification no. FG-BKT/SLB |
| 49 | Supplying and erecting integrated LED street light fitting 40 to 50 Watt IP 65 and 1K08 class having single piece pressure die cast aluminium housing, having system lumens output of Min. 4400 Lumens, min. efficiancy of 110 lumens/W, CRI>70, CCT upto 6500K, THD<10%, p.f.>0.95, operating range of 140-270V, inbuilt surge protection of 10kv, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2. |
| 50 | Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 6600 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2. |
| 51 | Supplyinganderecting 10-12Watt, 230voltintegral type LED Lamp suiable for B-22/E-27 base. |
| 52 | Supplying & erecting ready to use Retrofit T8 LED 18 / 20 W tube lightwith polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary. |
| 53 | Supplying, erecting & marking SPMCB 6A to 32A, B- series with rated short circuit breaking capacity (Icn) 10 KA in provided distribution boardas per specification No. SW-SWR/MCB |
| 54 | Supplying, erecting & marking DPMCB 6A to 32A, B- series with rated short circuit breaking capacity (Icn) 10 KA in provided distribution boardas per specification No. SW-SWR/MCB |
| 55 | Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB |
| 56 | Providing earthing with Galvanised cast iron earth platesize 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification No. EA-EP |
