|
| 1 | Reception Center Work |
| 2 | ExcavationEarth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the 2.8.1 All kinds of soil. PWD LUCKNOW SOR-2020-21,I/P-7.2.8.1/10 |
| 3 | PCC for BaseProviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) PWD LUCKNOW SOR-2020-21,I/P-8.4.1.3/12 |
| 4 | Brick SolingLaying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolling the same with three wheel road roller 80-100 KN as per Technical Specification Clause 412. PWD LUCKNOW SOR-2020-21,I/P-25.20.MORD-412 (4.18)/49 |
| 5 | FillingSupplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete. CPWD SOR-2021 Vol-I ,I/P- 2.27/95 |
| 6 | Random Rubble MasonryRandom rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : 7.1.1 Cement mortar 1:6 (1 cement : 6 coarse sand) CPWD SOR-2021 Vol-I ,I/P- 7.1.1/149 |
| 7 | PointingPointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : 13.33.1 Flush/ Ruled pointing. CPWD SOR-2021 Vol-II ,I/P-13.33.1/281 |
| 8 | Brick work with Mud MortorBrick work with common burnt clay bricks of class designation 7.5 in mud mortar. CPWD SOR-2021 VolI-I ,I/P- 14.25/300 |
| 9 | Plastering with mud mortorMud mortar made with local clay good earth.CPWD SOR-2021 VolI-I ,I/P- 14.24/300 |
| 10 | Kota Stone FlooringKota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the stab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand) PWD LUCKNOW SOR-2020-21,I/P-11.26.1/26 |
| 11 | Bathroom FlooringProviding and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. PWD LUCKNOW SOR-2020-21 ,I/P- 11.37/26 |
| 12 | Bathroom DadoProviding and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shadecomplete. UP PWD SSR 2020 ,I/P-11.37A/26 |
| 13 | Waterproofing Treatment to WC and BathProviding and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. CPWD SOR-2021 Vol-I ,I/P- 22.6/470 |
| 14 | Door and Window FrameProviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood.PWD LUCKNOW SOR-2020-21 ,I/P-9.1.1/19 |
| 15 | Door and Window ShutterProviding and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note- Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood.PWD LUCKNOW SOR-2020-21 ,I/P-9.5.1/19 |
| 16 | Flush DoorProviding and fixing ISI marked flush door shutters conforming to IS 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary. PWD LUCKNOW SOR-2020-21 ,I/P-9.21.1/19 |
| 17 | UPVC Door FrameProviding and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. CPWD SOR-2021 Vol-I ,I/P-9.143/207 |
| 18 | UPVC DoorProviding and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge (Single / double glass panes and silicon sealant shall be paid separately) Note For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein shall be made dimension ie in depth & width of profile shall be acceptable Vanation in profile dimension in higher side shall be accepted but no extra payment on this account 9.147 C.2 Casement door with top hung ventilator with 3D and S.S. friction hinges (400 * 19 * 1.9mm) made of (big series) frame 67 * 64 mm, sash 67 x 110 mm & mullion 67 * 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) (Openable Door with Top Fix) PWD LUCKNOW SOR-2020-21,I/P-9.147 C1/20 |
| 19 | UPVC VentilatorProviding and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge (Single / double glass panes and silicon sealant shall be paid separately) Note For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein shall be made dimension ie in depth & width of profile shall be acceptable Vanation in profile dimension in higher side shall be accepted but no extra payment on this account Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9±0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) PWD LUCKNOW SOR-2020-21,I/P-9.147 B.1/20 |
| 20 | LintelProviding Wood work for Lintel (a ) UP Teak Wood (Cut to Size) UP PWD SOR-2020-21,I/P-28(b)/14 |
| 21 | Butt HingesProviding and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete: 9.55.1 125x65x2.12 mm CPWD SOR-2021 Vol-II ,I/P-9.55.1/19 |
| 22 | Door BoltsProviding and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 9.62.1 (300x16 mm) CPWD SOR-2021 Vol-II ,I/P-9.62.1/19 |
| 23 | Tower BoltProviding and fixing ISI marked oxidised M.S. tower boit black finish. (Barrel type) with necessary screws etc complete 9.63 300x10 mm 9.63.1 250x10 mm CPWD SOR-2021 Vol-II ,I/P-9.63.1/19 |
| 24 | Door HandleProviding and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete_ENTI 9.66.1 125 mm CPWD SOR-2021 Vol-II ,I/P-9.66.1/19 |
| 25 | Electrical WorkCeiling FanSupply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. CPWD DSR 2022 E&M (I/P - 19.1/72) |
| 26 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.1.1.3 Group C. CPWD DSR 2022 E&M (I/P - 1.1.3/1) |
| 27 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. CPWD DSR 2022 E&M (I/P - 1.27.5/6) |
| 28 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1.27.5 8 Module (125mm x 125mm) CPWD DSR 2022 E&M (I/P - 1.27.5/6) |
| 29 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.14.15.2 90 mm dia (OD-90 mm & ID-76 mm nominal) CPWD DSR 2022 E&M (I/P - 14.15.2/43) |
| 30 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. CPWD DSR 2022 E&M (I/P - 1.41/7) |
| 31 | Sanitary InstallationsW.C.Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :17.3.1 W.C. pan with ISI marked white solid plastic seat and lid CPWD SOR-2021 Vol-II ,I/P- 17.3.1/356 |
| 32 | Wash BasinProviding and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer. CPWD SOR-2021 Vol-II ,I/P- 17.7A/358 |
| 33 | Bottle TrapProviding and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.CPWD SOR-2021 Vol-II ,I/P- 17.22A/360 |
| 34 | Towel RingProviding and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms. CPWD SOR-2021 Vol-II ,I/P- 17.72/369 |
| 35 | Soap Dish HolderProviding and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms. CPWD SOR-2021 Vol-II ,I/P- 18.65/412 |
| 36 | Bib CockProviding and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 18.50.1 15 mm nominal bore. CPWD SOR-2021 Vol-II ,I/P- 18.50.1/409 |
| 37 | Stop CockProviding and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms. CPWD SOR-2021 Vol-II ,I/P- 18.63/411 |
| 38 | CPVC PipeProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 18.8.2 20 mm nominal dia Pipes. CPWD SOR-2021 Vol-II ,I/P- 18.8.2/400 |
| 39 | Water TapProviding and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7.11 Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap. CPWD SOR-2021 Vol-II ,I/P- 17.7.11/358 |
| 40 | Soak PitConstructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. CPWD SOR-2021 Vol-II ,I/P- 19.33/445 |
| 41 | Brick ChamberConstructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : 19.30.2.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 CPWD SOR-2021 Vol-II ,I/P- 19.30.2.1/445 |
| 42 | RCC Septic Hume PipeSupply of 1200 RCC Septic hume pipe as per the specification. As Per Quotation |
| 43 | RoofingProviding and Installing Thatch Roofing with Bamboo Support at Site of size 11.20 X 6.4 M. As directed by Engineering incharge includingtools and tackles as per drawing and specifications. As Per Quotation |
| 44 | Watchmen Cabin |
| 45 | ExcavationEarth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the 2.8.1 All kinds of soil. PWD LUCKNOW SOR-2020-21,I/P-7.2.8.1/10 |
| 46 | FillingSupplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete. CPWD SOR-2021 Vol-I ,I/P- 2.27/95 |
| 47 | PCC for BaseProviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) PWD LUCKNOW SOR-2020-21,I/P-8.4.1.3/12 |
| 48 | Brick SolingLaying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolling the same with three wheel road roller 80-100 KN as per Technical Specification Clause 412. PWD LUCKNOW SOR-2020-21,I/P-25.20.MORD-412(4.18)/49 |
| 49 | Plinth ProtectionMaking plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. CPWD SOR-2021 Vol-I ,I/P- 4.17/112 |
| 50 | Brick work with Mud MortorBrick work with common burnt clay bricks of class designation 7.5 in mud mortar. CPWD SOR-2021 VolI-I ,I/P- 14.25/300 |
| 51 | Plastering with mud mortorMud mortar made with local clay good earth. CPWD SOR-2021 VolI-I ,I/P- 14.24/300 |
| 52 | Flooring for StepsProviding and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).11.47.2 Size of Tile 600x600 mm. PWD LUCKNOW SOR-2020-21,I/P-9.6.1.1/16 |
| 53 | LintelProviding Wood work for Lintel (b ) Sal wood (Cut to Size). UP PWD SOR-2020-21,I/P-28(b)/14 |
| 54 | Door and Window FrameProviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood. PWD LUCKNOW SOR-2020-21 ,I/P-9.1.1/19 |
| 55 | Door and Window ShutterProviding and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note- Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood. PWD LUCKNOW SOR-2020-21 ,I/P-9.5.1/19 |
| 56 | Butt HingesProviding and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete: 9.55.1 125x65x2.12 mm. CPWD SOR-2021 Vol-II ,I/P-9.55.1/19 |
| 57 | Door BoltsProviding and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 9.62.1 300x16 mm. CPWD SOR-2021 Vol-II ,I/P-9.62.1/19 |
| 58 | Tower BoltProviding and fixing ISI marked oxidised M.S. tower boit black finish. (Barrel type) with necessary screws etc complete 9.63 300x10 mm 9.63.1 250x10 mm. CPWD SOR-2021 Vol-II ,I/P-9.63.1/19 |
| 59 | Door HandleProviding and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete_ENTI 9.66.1 125 mm. CPWD SOR-2021 Vol-II ,I/P-9.66.1/19 |
| 60 | Thatch Roofing with Bamboo Support for Security Cabin Providing and Installing Thatch Roofing with Bamboo Support at Site of size 4 M X 4 M. As directed by Engineering incharge includingtools and tackles as per drawing and specifications. As Per Quotation |
| 61 | Bio - Toilet |
| 62 | ExcavationEarth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the 2.8.1 All kinds of soil. PWD LUCKNOW SOR-2020-21,I/P-7.2.8.1/10 |
| 63 | PCC for BaseProviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) PWD LUCKNOW SOR-2020-21,I/P-8.4.1.3/12 |
| 64 | Brick SolingLaying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolling the same with three wheel road roller 80-100 KN as per Technical Specification Clause 412. PWD LUCKNOW SOR-2020-21,I/P-25.20.MORD-412(4.18)/49 |
| 65 | Brick work in Foundation and PlinthBrick work with common burnt clay (non modular) bricks of class-150 in foundation and plinth in Cement mortar 1:4 (1 cement: 4 coarse sand) PWD LUCKNOW SOR-2020-21,I/P-9.6.1.1/ 16 |
| 66 | Plastering for Brickwork15 mm cement plaster 1:3 (1 cement 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall. PWD LUCKNOW SOR-2020-21,I/P-13.10/30 |
| 67 | Bio ToiletProviding and installing of Bio toilet with MS CONTAINOR Size: 18x6x8 ft , Height 8 ftWestern Style : 2 NosUrinal : 4 NosWith Complete Plumber FittingInside Wooden Work on WallsBase in PlywoodGents Toilet MS CONTAINOR Size: 9x6x8 ftLadies Toilet3 Western CommodWith Complete Plumber FitingAs directed by Engineering incharge includingtools and tackles as per drawing and specifications. As per quotation |
| 68 | Cafeteria Repiar Work |
| 69 | Scrapping of Old White WashScrapping old white or colour wash including disposal of refuse as directed by Engineer-In-charge within a distance of 60 meters (200 feet)UP PWD SSR 2020(Chapter 17 Serial no. 18 /58) |
| 70 | Dismantling of Existing PlasterDismantling existing plaster including disposal of refuse as directed by Engineer-In-Charge within a distance of 60.UP PWD SSR 2020(Chapter 17 Serial no. 16 /58) |
| 71 | BrickworkBrick work with common burnt clay (non modular) bricks of class-150 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement 4 coarse sand) PWD LUCKNOW SOR-2020-21,I/P-9.6.4.1/49 |
| 72 | Plaster, Wall PuttyProviding and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. PWD LUCKNOW SOR-2020-21,I/P-13.26/30 |
| 73 | Ceiling Plaster 6mm Celling plaster 1:3 (1 cement : 3 fine sand) cement & fine sand in F.M. not less than 1.25, 1:3 including chiping of RCC surface before ceiling plaster. The cost of including all material, labour T&P and scafolding etc. complete. UP PWD SSR 2020(Chapter 13 Serial no. 13) |
| 74 | Internal Plaster12mm Cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth.PWD LUCKNOW SOR-2020-21,I/P-13.1/30 |
| 75 | External PlasterWashed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in- charge (payment for providing grooves shall be made separately.UP PWD SSR 2020(Chapter 13 Serial no. 19) |
| 76 | Painting, Intarnal PaintingDistempering (first coat) with oil bound distemper of approved brand and manufacture and of required shade on undercoated wall surface to give an even shade over & including a priming coat with cement primer of approved brand and manufacture such as Berger, J&N, Shalimar, Asian, paints after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even with plaster of approved synthetic material and sand papered smooth including cost of all materials. UP PWD SSR 2020 (Chapter 15 Serial no. 13) |
| 77 | External PaintingFinishing walls with Textured exterior paint @ 3.28 Ltr. per 10Sqm of approved brand and manufacture and of required shade on undacorated wall surface to give even shade over including curing and cost of all material, labour, T&P etc. required for proper completion of work.for two coat.over one coat of primer applied 2.20Ltr 10 Sqm. UP PWD SSR 2020 (Chapter 15 Serial no. 32) |
| 78 | Slab WaterproofingProviding and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1) cement 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fibre cloth With average thickness of 120 mm and minimum thickness at khurra as 65 mm. PWD LUCKNOW SOR-2020-21,I/P-22.27.1/41 |
| 79 | Kota Stone FlooringKota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the stab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement: 4 coarse sand) PWD LUCKNOW SOR-2020-21,I/P-11.26.1/26 |
| 80 | Bathroom FlooringProviding and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. PWD LUCKNOW SOR-2020-21 ,I/P- 11.37/26 |
| 81 | Bathroom DadoProviding and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shadecomplete. UP PWD SSR 2020, I/P-11.37A/26 |
| 82 | Waterproofing Treatment to WC and BathProviding and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. CPWD SOR-2021 VolI-I ,I/P- 22.6/470 |
| 83 | Door and Window FrameProviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood. PWD LUCKNOW SOR-2020-21 ,I/P-9.1.1/19 |
| 84 | Door and Window ShutterProviding and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note- Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood. PWD LUCKNOW SOR-2020-21 ,I/P-9.5.1/19 |
| 85 | Flush DoorProviding and fixing ISI marked flush door shutters conforming to IS 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary.PWD LUCKNOW SOR-2020-21 ,I/P-9.21.1/19 |
| 86 | UPVC Door FrameProviding and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be mitred cut and jointed with plastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profile of Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 125 mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size of anchor dash fastners, all complete as per manufacturer\"s specification and direction of Engineer-in-charge. CPWD SOR-2021 Vol-I ,I/P-9.143/207 |
| 87 | UPVC DoorProviding and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge (Single / double glass panes and silicon sealant shall be paid separately) Note For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein shall be made dimension ie in depth & width of profile shall be acceptable Vanation in profile dimension in higher side shall be accepted but no extra payment on this account 9.147 C.2 Casement door with top hung ventilator with 3D and S.S. friction hinges (400 * 19 * 1.9mm) made of (big series) frame 67 * 64 mm, sash 67 x 110 mm & mullion 67 * 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) (Openable Door with Top Fix) PWD LUCKNOW SOR-2020-21,I/P-9.147C2/20 |
| 88 | UPVC VentilatorProviding and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge (Single / double glass panes and silicon sealant shall be paid separately) Note For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein shall be made dimension ie in depth & width of profile shall be acceptable Vanation in profile dimension in higher side shall be accepted but no extra payment on this account Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9±0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) PWD LUCKNOW SOR-2020-21,I/P-9.147 B.1/20 |
| 89 | LintelProviding Wood work for Lintel (a ) UP Teak Wood (Cut to Size) UP PWD SOR-2020-21,I/P-28(b)/14 |
| 90 | Butt HingesProviding and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete: 9.55.1 125x65x2.12 mm. CPWD SOR-2021 Vol-II ,I/P-9.55.1/19 |
| 91 | Door BoltsProviding and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete 9.62.1300x16 mm CPWD SOR-2021 Vol-II ,I/P-9.62.1/19 |
| 92 | Tower BoltProviding and fixing ISI marked oxidised M.S. tower boit black finish. (Barrel type) with necessary screws etc complete 9.63 300x10 mm 9.63.1 250x10 mm. CPWD SOR-2021 Vol-II ,I/P-9.63.1/19 |
| 93 | Door HandleProviding and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete_ENTI 9.66.1 125 mm. CPWD SOR-2021 Vol-II ,I/P-9.66.1/19 |
| 94 | Electrical WorkWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.1.1.3 Group C. CPWD DSR 2022 E&M (I/P - 1.1.3/1) |
| 95 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. CPWD DSR 2022 E&M (I/P - 1.12/3) |
| 96 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1.27.5 8 Module (125mm x 125mm) CPWD DSR 2022 E&M (I/P - 1.27.5/6) |
| 97 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 14.15.2 90 mm dia (OD-90 mm & ID-76 mm nominal) CPWD DSR 2022 E&M (I/P - 14.15.2/43) |
| 98 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. CPWD DSR 2022 E&M (I/P - 1.41/7) |
| 99 | Ceiling FanSupply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. CPWD DSR 2022 E&M (I/P - 19.1/72) |
