Tender For Various Drg Based Items For Corex - Pr - 33399391 & 33399392 33399391 0001 0001 300836327 SHAFT,DRIVE,DRG:PG-08-0130/ITEM:1 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 1 NO SHAFT TYPE : DRIVE , SIZE : DIA:360 X L: 5089 MM ADDITIONAL INFORMATION : DRAWING NO: PG-08-0130/REV:2,IT:1, FOR CAST HOUSE , DEDUSTING ID FAN,FORGING RATIO: 4:1 Item Details : 1.Drawing <(>&<)> QAP for witness and document submission[Drive Shaft with covers should be 4:1Forged EN24(material standard BS970 817M40 )Volume Hardened <(>&<)> Tempered220 – 250 BHN,UT as per SA 578 level B, after Proof Machining Ultrasound test as per ASTM A609 Level 1 , DP test as per ASTM E 165 ,Stamping, MTC, Balancing, Chemical analysis, Hardness test, impact test with other mechanical and chemical test ,Shaft material standard: material standard BS970 817M40 (EN24) grade] and other relevant quality check to be consider and to be approved by AMNS before start manufacturing. After Casting and Heat Treatment – Integral Test Piece will be identified by AMNS before separating from Casting. 2.All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 3.Final inspection will be as per approved QAP 4. Interchangeability certificate to be provided before dispatch the ready material. 5. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 6.Service engineer will require during installation and commissioning. Item Note : 2 33399391 0002 0002 300836328 HUB,450X345X425MM,DRG:PG-08-0130/ITEM:2 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 1 NO HUB SIZE : OD:450XID:345XL:425 MM ADDITIONAL INFORMATION : DRAWING NO: PG-08-0130/REV:2,IT:2,FAN MOUNTING,FOR CAST , HOUSE DEDUSTING ID FAN Item Details : 1.Drawing <(>&<)> QAP for witness and document submission[Drive Shaft with covers should be 4:1Forged EN24(material standard BS970 817M40 )Volume Hardened <(>&<)> Tempered220 – 250 BHN,UT as per SA 578 level B, after Proof Machining Ultrasound test as per ASTM A609 Level 1 , DP test as per ASTM E 165 ,Stamping, MTC, Balancing, Chemical analysis, Hardness test, impact test with other mechanical and chemical test ,Shaft material standard: material standard BS970 817M40 (EN24) grade] and other relevant quality check to be consider and to be approved by AMNS before start manufacturing. After Casting and Heat Treatment – Integral Test Piece will be identified by AMNS before separating from Casting. 2.All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 3.Final inspection will be as per approved QAP 4. Interchangeability certificate to be provided before dispatch the ready material. 5. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 6.Service engineer will require during installation and commissioning. Item Note : Page 2 of 5 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000106347 Date 15.02.2024 Submission Date 26.02.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Nilesh Jetani Contact Email Nilesh.Jetani@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Material / Service No. Quantity UOM Detail Description Other Details 3 33399391 0003 0003 300836334 COVER,450X351X20MM,DRG:PG-08-0130/IT:3 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 1 NO COVER TYPE : END COVER , SIZE : 450X351X20 MM ADDITIONAL INFORMATION : DRAWING.NO: PG-08-0130/REV:2,IT:3, FOR CAST HOUSE , DEDUSTING ID FAN Item Details : 1.Drawing <(>&<)> QAP for witness and document submission[Drive Shaft with covers should be 4:1Forged EN24(material standard BS970 817M40 )Volume Hardened <(>&<)> Tempered220 – 250 BHN,UT as per SA 578 level B, after Proof Machining Ultrasound test as per ASTM A609 Level 1 , DP test as per ASTM E 165 ,Stamping, MTC, Balancing, Chemical analysis, Hardness test, impact test with other mechanical and chemical test ,Shaft material standard: material standard BS970 817M40 (EN24) grade] and other relevant quality check to be consider and to be approved by AMNS before start manufacturing. After Casting and Heat Treatment – Integral Test Piece will be identified by AMNS before separating from Casting. 2.All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 3.Final inspection will be as per approved QAP 4. Interchangeability certificate to be provided before dispatch the ready material. 5. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 6.Service engineer will require during installation and commissioning. Item Note : 4 33399392 0001 0004 300874098 PIN,CYL,DRG:PG-07-0014/IT-06,STD,90MM,1 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 4 NO PIN,CYLINDRICAL DESIGN TYPE:STANDARD , SIZE:90 MM , LENGTH:144 MM DRAWING DRG NO:PG-07-0014/IT-06 , DRAWING REV NO:00 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : Page 3 of 5 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000106347 Date 15.02.2024 Submission Date 26.02.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Nilesh Jetani Contact Email Nilesh.Jetani@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Material / Service No. Quantity UOM Detail Description Other Details 5 33399392 0002 0005 300874300 PIN,CYL,DRG:PG-07-0014/IT-08,THRD,90MM, Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 4 NO PIN,CYLINDRICAL DESIGN TYPE:THREADED , SIZE:90 MM , LENGTH:324 MM DRAWING DRG NO:PG-07-0014/IT-08 , DRAWING REV NO:00 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : 6 33399392 0003 0006 300874291 PIN,CYL,DRG:PG-07-0014/IT-09,THRD,80MM, Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 4 NO PIN,CYLINDRICAL DESIGN TYPE:THREADED , SIZE:80 MM , LENGTH:324 MM DRAWING DRG NO:PG-07-0014/IT-09 , DRAWING REV NO:00 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : Page 4 of 5 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000106347 Date 15.02.2024 Submission Date 26.02.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Nilesh Jetani Contact Email Nilesh.Jetani@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Material / Service No. Quantity UOM Detail Description Other Details 7 33399392 0004 0007 300874334 BUSH,MTLC,DRG:PG-07-0014/IT-10,PLAIN,80 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 4 NO BUSH,METALLIC TYPE/DESIGN TYPE:PLAIN , SIZE (ID X OD X WIDTH):80X95X62 MM DRAWING DRG NO:PG-07-0014/IT-10 , DRAWING REV NO:00 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : 8 33399392 0005 0008 300874319 BUSH,MTLC,DRG:PG-07-0014/IT-11,PLAIN,90 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 4 NO BUSH,METALLIC TYPE/DESIGN TYPE:PLAIN , SIZE (ID X OD X WIDTH):90X105X62 MM DRAWING DRG NO:PG-07-0014/IT-11 , DRAWING REV NO:00 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : Page 5 of 5 ArcelorMittal Nippon Steel India Limited AM/NS HAZIRA PLANT 27th KM, Surat-Hazira Road,,HAZIRA,394270,Gujarat,India GSTIN 24AAACE1741P1ZN PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000106347 Date 15.02.2024 Submission Date 26.02.2024 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ Mr. Nilesh Jetani Contact Email Nilesh.Jetani@amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Material / Service No. Quantity UOM Detail Description Other Details 9 33399392 0006 0009 300876768 PIN,CYL,DRG:PG-07-0014/IT-07,STD,90MM,2 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 8 NO PIN,CYLINDRICAL DESIGN TYPE:STANDARD , SIZE:90 MM , LENGTH:205 MM DRAWING DRG NO:PG-07-0014/IT-07 , DRAWING REV NO:0 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note : 10 33399392 0007 0010 300891443 LEVER,MTLC,DRG:PG-07-0014/IT-01 Technical Details Name : Amar Dhok Contact : Email : AMAR.DHOK@AMNS.IN 2 NO LEVER,METALLIC ADDITIONAL INFORMATION:WELDED LEVER ASSEMBLY -R H AND LH DRAWING DRG NO:PG-07-0014/IT-01 , DRAWING REV NO:0 Item Details : 1. Drawing will be approved by AMNSIL before start manufacturing. 2. QAP will be approved by AMNSIL before start manufacturing with considering below minimum quality requirements. MOC: Volume Hardened and tempered(forging ratio 4:1) Mechanical properties: UTS,YS, EL, RA, Notch Impact energy, Hardness-Identification and stamping before detaching the integral test bar from forging for axle and separate test bar for wheel after HT / proof machining will be witnessed by AMNSIL. Chemical , Mechanical properties and hardness will be witnessed by AMNSIL during stage inspection. UT(proof machined):SA388-2mm FBH on DGS scale. It will be witnessed by AMNSIL during stage and final inspection. MPT:SA275 acceptance criteria-ASME SEC VII Div 2-clause 7.5.6.2(No linear indication permitted). It will be witnessed by AMNSIL during stage and final inspection. DPT:ASME SEC V. SE165-Acceptance criteria, ASME Sec VII Div.1. Appendix 8. No linear indication permitted. Heat treatment to be done. 3. All NABL certified test reports(UT.RT,MTC,CHEMICAL ANALYSIS, other related reports) to be provided by vendor before dispatch. 4. VALID CALIBRATION CERTIFICATES OF ALL METHODOLOGICAL INSTRUMENTS AND NABL CERTIFICATE OF TESTING LAB . 5. Final inspection will be as per approved QAP. Item Note :
