Tender For Construction Of Girls And Boys Seprate Toilets Blocks At Govertment Girls Inter College Babai Jalaun
Tender Value
19.16 Lakhs
Estimated cost
Bid Submission
23 Feb 2024
0 days left
EMD
40000
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
babai → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Girls And Boys Seprate Toilets Blocks At Govertment Girls Inter College Babai Jalaun
BOQ
| Sl. No. | Item Description |
| 1 | Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-20 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm dia piles. as per DSR-20.3.1 |
| 2 | Extra / additional over single under ream for providing additional bulbs in under reamed piles, under specified diameter(only the nos. of extra bulbs are to be paid) 300 mm dia piles.As per Specification DSR-20.4.1 |
| 3 | Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge .Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) . load bearing capicitty not less then 2.5 times ofPile load .Initial Testas per Specification DSR-20.6.1.1 |
| 4 | Vertical load testing of piles in accordance with I. S. 2911 ( part iv ) including installation of loading plateform & preperation of pile head or construction of test cap & dismantling of test cap after test etc. complete as per specification and the direction of Engineer - in - Charge . load bearing capicitty not less then 1.5 times ofPile load .Initial Testas per Specification DSR-20.6.2.1Routine Test |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. 2.6.1 All kinds of soil. As per specification DSR-Item no-2.6.1 |
| 6 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.As per specification DSR-Item no-2.25 (A) |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from natural sources) As per specification DSR-Item no-4.1.8+(4.1.5-4.1.6) |
| 8 | Supplying and filling in plinth withsand under floors, including watering, ramming, consolidating and dressing complete. As per spefication DSR-2.27 |
| 9 | Providing andinjectingchemical emulsionforpreconstructional antitermite treatment andcreatinga chemical barrier underand alroundthe column pits wall trenchesbasement excavation top surface if plinth filling junctionofwall and floor, alongthe the externalperimeter ofbinding expansionjoints,surrounding ofpipes andconduits etc, complete (plinth area of the building at groundflooronly shall be measured as per I.S.6313 ( Part II 1981 ) Alderine emulsifiable concentrate or any other approved materialsuch as Heptrachlor or chordancewill be used. Therateofapplication ofchemical emulsion shallbe asfollows : (1 Treatment for masonary & foundation 5 liters pe r/ 100 Sqm.(2) Back fill inimmediate contact with foundation 7.5 liters / 100 Sqm. (3) Treatment of topsurfaceof plinth filling 5 liters / 100 Sqm. (4)Treatmentjunction of wallandthe floor 7.5 liters / 100 Sqm. (5)Treatmentofsoilalong external perimeter of building 7.5liters / 10 Sqm.(6) Treatment of soil under apronalong external perimter 5 liters / 100 Sqm. |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).bands. As per Specification DSR-5.3 |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). slab As per Specification DSR-5.3 |
| 12 | Brick work with common burnt clay(non modular) bricks of class designation 150 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) including all material labour, T&P required for proper completion of work . As per specification DSR.-6.1.2 |
| 13 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) all material labour, T&P required for proper completion of work . As per specification DSR.-4.10 |
| 14 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.all material labour, T&P required for proper completion of work . As per specification DSR.-4.13 |
| 15 | Brick work with common burnt clay(non modular) bricks of class designation 150 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)all material labour, T&P required for proper completion of work . As per specification DSR.-6.4.2 |
| 16 | Brick work with common burnt clay(non modular) bricks of class designation 150 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) .all material labour, T&P required for proper completion of work . As per specification DSR.-6.4.1 |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.all material labour, T&P required for proper completion of work . As per specification DSR.-5.22 |
| 18 | 12 mm cement plaster of mix 1:6 (1 cement: 6 coarse sand) Including all material labour, T&P required for proper completion of work . As per specification DSR13.4.2 |
| 19 | Making grooves 10 to 12mmwide x 8 mm deep inplaster of the walls or in ceiling vertically or horizontally as required. As per specification DSR-5.30 |
| 20 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade completeDSR-8.31 |
| 21 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. DSR-11.27 |
| 22 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. As per specification DSR-11.37 |
| 23 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate Including all material labour, T&P required for proper completion of work . As per specification DSR 11.30 |
| 24 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer.Including all material labour, T&P required for proper completion of work . As per specification DSR13.41 |
| 25 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm).primer.Including all material labour, T&P required for proper completion of work . As per specification DSR13.14.1 |
| 26 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.primer.Including all material labour, T&P required for proper completion of work . As per specification DSR13.80 |
| 27 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes |
| 28 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:Applying a slurry coat of neat cement using 2.75 kg/sqm ofcement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using brokenricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat ofcement slurry using 2.75 kg/ sqm of cement admixed with water proofingcompound conforming to IS : 2645 and approved by Engineer-in-charge. primer.Including all material labour, T&P required for proper completion of work . As per specification DSR 22.70 |
| 29 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work primer.Including all material labour, T&P required for proper completion of work . As per specification DSR13.52.1 |
| 30 | Finishing with Deluxe Multi surface paint system for interiors and exteriorsusing Primer as per manufacturers specificationsPainting wood work with Deluxe Multi Surface Paint of requiredshade. Two or more coat applied @ 0.90 ltr/10 sqm over anunder coat of primer applied @0.75 ltr/10 sqm of approvedbrand and manufacture |
| 31 | Construction of drain of size of size 150 x 150 mm along with apron including excavation,base concrete 1:4:8 in thickness of 7.5cm of and brick work in foundation 1:4( 1 cement : 4 coarse sand) and brickwork in half brick thick in foundation 25mm thick cement concrete (1:2:4 mix) flooring base and 20mm thick plaster (1:2) finished with neat cement. (Analysis) |
| 32 | Centering and shuttering including strutting, propping etc. and removal of form work for : Suspended floors, roofs, landings, balconies and access platform as per specification DSR-5.9.3 |
| 33 | Centering and shuttering including strutting, propping etc. and removal of form work for : Lintels, beams, plinth beams, girders, bressumers and cantileversas per specification DSR-5.9.5 |
| 34 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.DSR-9.21.1 |
| 35 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Providing & fixing of hold fast for chaukhatsof doors and windows. DSR-10.1 |
| 36 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Providing & fixing of door / windows grill. DSR-10.1 |
| 37 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Z-Section steel windows DSR-10.1 |
| 38 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Providing & fixing of hold fast for chaukhatsof doors and windows. DSR-10.1 |
| 39 | Fixingofsteelorwoodenchaukhats in position. (a) Door chaukhats |
| 40 | Fixingofsteelorwoodenchaukhats in position. (c) Ventilator chaukhats |
| 41 | Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete |
| 42 | Providing and fixing stainless steel handles with screws etc. complete (a) 150 mm |
| 43 | Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . |
| 44 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests . As specification DSR-17.1.1 |
| 45 | Providing and fixing white vitreous china pedestal type water closet( European type W.C. pan ) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid. As specification DSR-17.2.1 |
| 46 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require a)White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap. As specification DSR-17.7.4 |
| 47 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Felxible pipe b) 40mm dia . As per specification 17.28.2.2 |
| 48 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. As per specification DSR17.31 |
| 49 | Providing & fixing PTMT towl rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing not less than 190 gms.As per specification -17.73.2 |
| 50 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms |
| 51 | Providing and fixing ofupvc SWR ring fit pipe of class B of ISI mark Confirming to IS code 13592 (make prince, supreme finolex) in internal works of toilet and RWP etc. including fixing with rubber rings etc. including cost of all material, labour etc. complete.including excavation & trenches etc complete a) 110mm diameter.Approved make approved by Engineer -in-charge. |
| 52 | Haunching of SWR pipe 90mm or 110mm with pcc 1:5:10 cement concrete ( 1 cement:2 coarse sand:4 stone grit) ch-25 item no.2 .Approved make approved by Engineer -in-charge. |
| 53 | Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.(ch-23 sec 34) .Approved make approved by Engineer -in-charge. |
| 54 | Supply and fixing of UPVC S.W.R. Cowel confirming to IS-14735.(ch-23 item no.38) Size 75/90 mm .Approved make approved by Engineer -in-charge. |
| 55 | Supply and fixing of UPVC S.W.R. Cowel confirming to IS-14735.(ch-23 item no.38) Size Size 110 mm .Approved make approved by Engineer -in-charge. |
| 56 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.a) 110mm.As per specification DSR.12.22 |
| 57 | Providing and fixing unplasticised -PVC pipe clips of approved designto unplasticised - PVC rain water pipes by means of 50x50x50 mmhard wood plugs, screwed with M.S. screws of required length,including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete DSR-12.43.2 |
| 58 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work-Exposed on wall .As per specification DSR.18.7.3 .25mm dia nominal outer dia pipes |
| 59 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. DSR-12.41.2 |
| 60 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 16mm dia nominal dia pipesDSR-18.11.1 |
| 61 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 16mm dia nominal dia pipesDSR-18.11.1 |
| 62 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.45 cm length i) 15mm nominal bore. As per specification DSR-18.21.2.1 |
| 63 | Providing & fixing CP brass bib cock of approved quality conforming to IS 893115mm nominal bore . as per specification 18.49.1 |
| 64 | Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. .15mm nominal bore as per specification 18.51.1 |
| 65 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore as per specification 18.53 |
| 66 | Providing and fixing brass stop cock of approved quality. 15mm nominal Dsr-18.16.1 |
| 67 | Providing and fixing brass stop cock of approved quality. 20mm nominal boreDsr-18.16.2 |
| 68 | Providing and fixing gun metal gate valve with wheel of approved quality(screwed end).. 25mm dia nominal bore as per specification 18.17.1 |
| 69 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore.as per specification 18.18.3 |
| 70 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 71 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. a) Pipes 80mm to 300mm diameter. DSR-2.10.1.2 |
| 72 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard designInside size 900x800mm and 500mm deep including CI cover with frame With FPS bricks of class designation 75 DSR-19.7.1.1 |
| 73 | Extra for depth of man hole size 900x800mm |
| 74 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar DSR-19.15.1 |
| 75 | Providing and fixing of UPVC SWR ring fit pipe of class B of ISI mark Confirming to IS code 13592 (make prince, supreme finolex) in internal works of toilet and RWP etc. including fixing with rubber rings etc. including cost of all material, labour etc. complete including excavtion trenches etc comp. a) 110mm diameter |
| 76 | Providing and fixing of UPVC SWR ring fit pipe of class B of ISI mark Confirming to IS code 13592 (make prince, supreme finolex) in internal works of toilet and RWP etc. including fixing with rubber rings etc. including cost of all material, labour etc. complete including excavtion trenches etc comp. b) 160mm diameter |
| 77 | Haunching of SWR pipe 90mm or 110mm or 160mm with pcc 1:5:10 cement concrete ( 1 cement:2 coarse sand:4 stone grit) AR |
| 78 | Wiring for light point/fan point/exhaust fan point/call bell pointwith 1.5 sqmm FR PVC insulatedcopper conductor single core cable in surface / recessed PVC conduit,with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable etc. as required. Group ASI no-1.10.1 |
| 79 | Wiring for twin control light point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, 2 way modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sqmm FR PVC insulated copper conductor single core cable etc. as required. SI no-1.11 |
| 80 | Wiring forcircuit / submain wiring alongwith earth wire withthe following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 2.5 sq.mm. + 1 x 2.5 sq.mm. Earth wire DSR-1.14.2 |
| 81 | Wiring forcircuit / submain wiring alongwith earth wire withthe following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 4 sq.mm. + 1 x 4 sq.mm. Earth wire SI -1.14.3 |
| 82 | Wiring forcircuit / submain wiring alongwith earth wire withthe following sizes of PVC insulated,copper conductor single core cable in surface/ recessed PVC conduit as required. 2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire SI no-1.14.4 |
| 83 | Supply and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required : 20 mm. SI no-1.21.1 |
| 84 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 pair SI no-1.18.2 |
| 85 | Supplying and fixing metal box of following size (nominal size) on surface or recess with suitable size of phenolic laminated sheet cover in fromt including paintingetc. as required. 75 mm x 75 mm x 60 mm deep SI no-1.22.1 |
| 86 | Supplying and fixing following size / modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75 mmX75 mm) SI -1.27.1 |
| 87 | Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. SI no-1.26 |
| 88 | Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing3 pin 5/6 amps. modular socket outlet and 5/6 amps. modular switch, connection, painting etc. as required.SI -1.31 |
| 89 | Supply and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps. modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required. SI no-1.32 |
| 90 | Supplying and fixing followingway, three pole and neutral, sheet steel, TP MCB distribution board, 415 volts,on surface /recess,completewithtinnedcopper busbar, neutral busbar, earth bar, din bar,detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). 4 way (4 + 12), Double door, horizontal type SI no-2.4.1 |
| 91 | Supplying & fixing single pole, blanking plate in the existing MCBDBcomplete etc. as required. DSR-2.11 |
| 92 | Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required. SI no-1.50.1 |
| 93 | Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. SI no-1.51 |
| 94 | Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure withcover plate having locking arrangement and watering pipe 2.7 m long etc, with charcoal/coke and salt as required.SI no-5.4 |
| 95 | Earthing withGI earth pipe4.5 mtr long, 40 mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with coke and salt as required.SI-5.2 |
| 96 | Supplying and laying25 mm x 5 mm. G.I. strip at 0.50 M. below ground as strip earth electrode, including connection and terminating with nut, bolt, spring, washer etc as required (jointing shall be done by overlapping and with 2 sets of brass nut bolt and spring washer spaced at 50 mm).SI no-5.90 |
| 97 | Providing and layingearthconnections from earth electrode with 6 SWG dia G.I. wire in 15 mm dia G.I. pipefromearth electrode as required. 5.12 |
| 98 | Providing and fixing 6 SWG dia G.I. wire onsurfaceorin recessfor loop earthing as required.SI no-5.16 |
| 99 | S/F of single light wall bracket (Cat-AAA) on matching M.D.F.E.G. board base etc. complete in all respects. Category AA SI no-412 |
| 100 | S/F of recess/surface/pendent mounted 8 to 8watt LED down lighter having powder coated die cast aluminium housing with heat sink, diffuser / reflectorand driver set complete in all respectCategory AAA SI no-1401 |
| 101 | S/F of LED Tube Light with batten suitable for up to 1x22 watt LED tube light fitting including tube on surface complete in all respect.SI-1413 |
| 102 | Supplyof AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required..300mm sweep |
| 103 | Supply and fixing brass nickel plated compression glands for PVC insulated armoured, served, sheathed cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth conductor SI no-503 ,300 sqmm 3 1/2core |
AI Tender Summary
Tender Timeline
Feb 13, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 23, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 23, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender