Tender For Establishment Of Open Gymnasium In Various Panchayaths Of Thrithala Constituency (Pattithara, Chalissery, Nagalassery And Paruthur)-Installation Of Gym Equipment - Retender, palakkad-Kerala

Establishment Of Open Gymnasium In Various Panchayaths Of Thrithala Constituency ( Pattithara, Chalissery, Nagalassery And Paruthur ) -Installation Of Gym Equipment - Retender , Open Gym Equipment , Od166347 / 2023_2024 : Air Walker - Supply And Installation Of Air Walker Having The Following Specifications: Dimensions: ( L X W X H ) 1190 X 380 X 1244 Mm. Main Frame- Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Dually Bending Design. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle&Ndash; Ø 42 Mm Od Round Gi Pipe. Handle &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use To Support It. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S - Pp / Nylon / Hdpe Material. Bracket - 8 Mm Thick Laser Profile Is Use To Support Paddle Frame. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Pin&Rsquo;S &Ndash; Ø 25Mm M.S. Bright Bar Pin. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Bearing Bushes -Ø 60 Mm Od Seamless Pipe. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166348 / 2023_2024 : Chest Press ( Double ) - Supply And Installation Of Double Chest Press Having The Following Specifications: Dimensions: ( L X W X H ) 1955 X 710 X 1900 Mm. Main Center Pipe - Ø 114 Mm Od B; Class Gi Pipe. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250Mm & 8 Mm Thick. Foundations Cover Cap- Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame - Made Up Of Ø 48 Mm Od B; Class G.I. Pipe. Handle - Made Up Of Ø48Mm Odb; Class G.I. Pipe. Link - Made Up Of Ø 48 Mm Odb; Class G.I. Pipe. Seat & Back Rest &Ndash; 380 X 275 X 60 Mm Thick High-Density Polyethylene ( Hdpe ) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Bearing Bush Closing Cap&Rsquo;S&Ndash; Pp / Nylon / Hdpe Material. Handle Must Be Connected With Frame By 8 Mm Laser Cutting Ms Profile. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin &Ndash; Made Up Of Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Grips - High Quality Rubber Ø 46 Mm Od. Circlips&Ndash;A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166349 / 2023_2024 : Triple Twister - Supply And Installation Of Triple Twister ( Standing Position - 2 And Seating Position - 1 ) Having The Following Specifications: Dimensions: ( L X W X H ) 1500 X 1500 X 1420 Mm. Main Frame &Ndash; Ø 114 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Seat Plate Support &Ndash; Ø 60 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Seating Ring - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe Made By Rolling. Seating Ring Support - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Remaining Frame &Ndash; Is Made By 100 X 50 X 2.5 Mm Rectangular Pipe. Standing Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Seat Position And Other Two Standing Position Plates Are Fixed 120 Degrees Each From Other. Handle &Ndash; Ø 33 Mm &Ldquo;B&Rdquo; Class G.I. Pipe Made By Rolling. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Used Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin &Ndash; Made Up Of Ø 25Mm M.S. Bright Bar. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166350 / 2023_2024 : Leg Press ( Double ) - Specifications: Dimensions: ( L X W X H ) = 1676 X 400 X1500 Mm. Main Frame - Ø 114 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundations Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Link - Is Ø 60 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Seat Frame - Ø 42 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Leg Press Back Rest Should Be Angled In 120 -130 Degree. Foot Rest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 2 Mm Thick Use To Support It. Seat & Back Rest &Ndash; 380 X 275 X 60 Mm Thick High-Density Polyethylene ( Hdpe ) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Link Connected With Frame By 8 Mm Thick Laser Cutting Ms Profile. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S- Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Ofm.S. Round Plate OfØ 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Pin&Ndash; Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlip&Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166351 / 2023_2024 : Rower - Supply And Installation Of Rower Having The Following Specifications: Dimensions: ( L X W X H ) = 1472 X 915 X 1040 Mm. Upper And Bottom Pipes - Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Angle Between Handle And Horizontal Surface Is 75 - 80 Degree. Linkages &Ndash; Ø 48 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Seat & Back Rest &Ndash; 380 X 275 X 60Mm Thick High-Density Polyethylene ( Hdpe ) Blow Molded With M10 Integrated Wall Thickness 3 To 4 Mm. Foot Resting Pipe - Ø 60 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. End Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø250 Mm & 8Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Pin &Ndash; Ø 25 Mm M.S. Bright Bar Pin. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Bearing Bushes - Ø 60 Mm Od Seamless Pipe / Bar. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Grips &Ndash; High Quality Rubber 46 Mm Od. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166352 / 2023_2024 : Shoulder Builder ( Double ) - Supply And Installation Of Shoulder Builder Having The Following Specifications: Dimensions: ( L X W X H ) 890 X 558 X 1500 Mm. Main Frame - Made From Ø 114 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Shoulder Ring Pipe - Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Shoulder Ring Pipe Support &Ndash; Ø 25 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Nylon Knob With Bearing &Ndash; Is Fixed On Shoulder Ring Pipe For Rotating Purpose ( 2 Set To Be Fixed In A Position For Kids And Adults ) . Top Closing Cap&Rsquo;S- Pp / Nylon / Hdpe Material. Closing Cap &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe Andtop Support Ofm.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin &Ndash; Ø 25 Mm M.S. Bright Bar Pin. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick.≪Br≫Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlips &Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166353 / 2023_2024 : Sit-Up Board - Supply And Installation Of Sit-Up Board Having The Following Specifications: Dimensions: ( L X W X H ) 1570 X 450 X 660 Mm. Main Frame - Made From Ø 33 Od &Ldquo;B&Rdquo; Class G.I. Pipe Bending Design. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 60 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Remaining Frame - Ø 60 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe And 100 X 50 Ms Pipe. Backrest Seat - Made Of M.S Checkered Plate Sheet Of 3 Mm Thickness Size 1100 Mm X 310 Mm. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166354 / 2023_2024 : Sky Walker - Supply And Installation Of Sky Walker Having The Following Specifications: Dimensions: ( L X W X H ) 1720 X 910 X 1700 Mm. Main Frame - Made Of Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Dually Bending Design. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Vertical Support - Ø 42 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Handle - Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Dually Bending Design. Leg Movement Frame &Ndash; 50 Mm X 50 Mm X 2 Mm Thick Square Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use For To Support It. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S&Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm M.S Pipe. And Top Support Ofm.S. Round Plate OfØ 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber Ø 46 Mm Od. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin &Ndash;Made Of Ø 25Mm M.S. Bright Bar. Circlips &Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166355 / 2023_2024 : Surfboard - Dimensions: ( L X W X H ) 1090 X 890 X 1390 Mm. Main Frame &Ndash; Made From Two Pipes Of Ø 114 Mm Od &Ldquo;B&Rdquo; Classgi Pipe. Foundation Plate &Ndash;M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Connecting Pipe - Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Is Used To Connect Both Main Frame Pipes At Top End And Ø 42 Mm Pipe Is Used To Connect At Bottom End. Handle - Ø 42 Mm And Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Support Pipe &Ndash; Ø 60 Mm Must Be Used To Support Leg Movement Frame. Leg Movement Frame&Ndash; Ø 42Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Footrest - Cast Iron 325 X 270 X 8 Mm Thick And M.S. Plate Of 250 X 200 X 2 Mm Thick Use For To Support It. Bracket - 8Mm Thick Laser Profile Is Use To Support Leg Movement Frame. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S&Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Ofm.S. Round Plate OfØ 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber Ø 46Mm Od. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin &Ndash; Made Of Ø 25Mm M.S. Bright Bar. Circlips &Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166356 / 2023_2024 : Cross Trainer ( Double ) - Supply And Installation Of Double Cross Trainer Having The Following Specifications: Dimensions: ( L X W X H ) 2280 X 550 X 1650 Mm. Main Frame- Made Of Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Dually Bending Design. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Vertical Support - Ø 42 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Handle - Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe Dually Bending Design. Leg Movement Frame &Ndash; 50 Mm X 50 Mm X 2 Mm Thick Square Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use For To Support It. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S&Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od B Class G.I. Pipe. And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin &Ndash;Made Of Ø 25Mm M.S. Bright Bar. Circlips &Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-100 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166357 / 2023_2024 : Back Extension - Supply And Installation Of Back Extension Having The Following Specifications: Dimensions: ( L X W X H ) 1060 X 730 X 990 Mm. Main Frame - Made From Ø 88 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 42 Mm Od &Ldquo;B&Rdquo; G.I Pipe.Seat Rest Pipe &Ndash; Ø 42 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Handle Pipe &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 3 Mm Thick Used To Support It. Footrest Pipe &Ndash; Ø 42 Mm Od &Ldquo;B&Rdquo; Class G.I Pipe And 80 X 40 Mm Ms Rectangular Pipe. Closing Cap &Ndash; Pp / Nylon / Hdpe Material. Seat &Ndash; 360 X 300 X 2 Mm Thick M.S. Seat With Corner Fillet For Safety. Grips - High Quality Rubber Ø 46 Mm Od. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166358 / 2023_2024 : Push-Up Bar And Dip Station - Supply And Installation Of Push-Up Bar And Dip Station Having The Following Specifications: Providing And Fixing Push Up Bar Made From G.I. Pipe. Dimensions: ( L X W X H ) 1220 X 530 X 1500 Mm. Main Frame - Ø 88 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe.Leg & Hand Support - Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Top Closing Cap &Ndash; Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap&Rsquo;S- Plastic Molded. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80 - 120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166359 / 2023_2024 : Arm And Paddle Bike - Supply And Installation Of Arm And Paddle Bike Having The Following Specifications: Dimensions: ( L X W X H ) 990 X 500 X 880 Mm. Main Frame &Ndash;100 Mm X 50 Mm X 2.5 Mm Rectangular Cr Pipe With Bending Design. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Round Pipe Dully Bending Design. Side And Top Cover &Ndash; 1.6 Mm Thick Ms Laser Cutting Profile Is Used. Seat &Ndash; 380 X 275 X 60 Mm Thick Hdpe Blow Moulding. Paddle &Ndash;100 Mm X 50 Mm Capsule Pipe And 40 X 16 Mm Ms Flat Should Be Used For Connecting The Paddle And Shaft.Closing Cap&Rsquo;S &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Ofm.S. Round Plate OfØ 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe.Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Bearing - Use Is 6005 Permanent Lubricating Sealed Reputed Brand. Shaft -Made Up Of Ø25Mm Od Ms Bright Bar. Circlips&Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 - 120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166360 / 2023_2024 : Horse Rider - Supply And Installation Of Horse Rider Having The Following Specifications: Dimensions: ( L X W X H ) 1140 X 400 X 1400 Mm. Main Frame - Ø 114 Mm Odb; Class Gi Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame &Ndash; Is Made By Ø 48 Mm Odb; Class Gi Pipe. Seat Frame &Ndash; Is Made By Ø 48 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Seat Position Must Be Horizontal To 110 -120 Degree. Link - Made Up Of Ø 48 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Angle Between Link And Ground Position Is 10-20 Degree. Handle - Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Paddle Vertical Support - Ø 60 Mm Odb; Class Gi Pipe. Handle Frame- Ø 42 Mm Odb; Class Gi Pipe Dually Bending Design. Foot Pipe - Ø 33 Mm Od &Ldquo;B&Rdquo; Class Gi Pipe. Support Frame &Ndash; 10 Mm Thick Ms Flat Is Used. Seat- Dimension 320 X 270 X 100 Mm Blow Moulded Wall Thickness 4Mm Material Hdpe. Bearing Bush Closing Cap &Ndash; Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin &Ndash; Made Of Ø 25 Mm M.S. Bright Bar. Grips - High Quality Rubber Ø 46 Mm Od. Circlips &Ndash; A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 60 To 70 Micron. Safety Instructions And Exercise Chart - Start &Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Od166361 / 2023_2024 : Single Bar - Supply And Installation Of Single Bar Having The Following Specifications: Dimensions: ( L X W X H ) 3550 X 2590 Mm. Main Frame - Made From Ø 48 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Frame Of Single Bar &Ndash; Ø 33 Mm Od &Ldquo;B&Rdquo; Class G.I. Pipe. Foundation Plate &Ndash; M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Top Closing Cap&Rsquo;S - Decent Design Size Pp / Hdpe / Ms. Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart &Ndash; Made From Aluminum / Stainless-Steel Stick-On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. , Inauguration Stone , Od166386 / 2023_2024 : Providing And Fixing 18 Mm Thick Gang Saw Cut, Mirror Polished, Pre-Moulded And Pre Polished, Machine Cut For Inauguration Granite Stone Of Required Size, Approved Shade, Colour And Texture Laid Over 20Mm Thick Base Of Cement Mortar 1:4 ( 1 Cement : 4 Coarse Sand ) Joint Treated With White Cement, Mixed With Matching Pigment, Epoxy Touchups Including Rubbing, Curing Etc. Complete At All Levels. Area Of Slab Over 0.50 Sqm , 16.21 : Engraving Letters In Hard Stone , 13.71 : Lettering With Black Japan Pint Of Approved Brand And Manufacture

INR 2950 /-

INR 50000.0 /-

INR 36.24 Lakhs /-