Supplying, Installation And Commissioning Of Lab Tables For Room No - 374 And General Laboratory Room No - 570 For Biotechnology Department At Ballygunge Science College Campus, University Of Calcutta, Kolkata-West Bengal

Supplying, installation and commissioning of lab tables for Room no - 374 and General Laboratory Room no - 570 for Biotechnology Department at Ballygunge Science College Campus, University of Calcutta Supplying, Installation, Commissioning Including Accessories Of Island Laboratory Table:4870 Mm L X1800 Mm D X 900 Mm H Island Storage Based Island Bench Withshutter Drawer Under -Storage, Electrical Truncking Reagent Shelf Above The Table Top & Granite Top.Should Be Made Of Crca Ms With Pure Epoxy Powder Coating And Are Of 1Mm Thickness. The Master Upright Should Be Of The Dimensions: 300 X 150 X 1.2 Mm. It Should Be Made From 1.2Mm Thick Crca Ms With Pure Epoxy Powder Coating.It Should Have An Open-Able Door For Easy Service Maintenance And Should Extend Till The False Ceiling. The Vertical Upright Should Form The Backbone For Internal Distribution Of Gds, Electrical Supply Systems Shelves And Top Units And Should Be Constructed From 16-Gauge Crca Formed Steel Panels With Removable Covers. Shelf Height Should Be Adjustable With An Increment Of 1Inch / 25Mm. Uprights Should Be Supplied With Adjustable Feet From -5Mm To +20Mm. Depending Upon The Layout, Height Adjustable Shelves Should Be Provided Between Uprights With 1” Of Height Adjustability. The Ends And Intermediate Vertical Supports Should Be 2Mm Thick Aluminum Extrusion With Ms Brackets Of 2 Mm Thick. Toughened Glass Should Be Put-On Over These Shelves For Taking Care Of Bottle Marks / Corrosion. Suspended Welded Cabinet Body Should Be Of Flush Face Construction With Intersection Of Vertical And Horizontal Members Like Lh And Rh Side Panel Along With Front Horizontal Channel, Back Panel And Bottom Panel. The Storage Cabinets Should Be Fixed And Should Also Have The Provision For Leg Space As Per The Need. It Should Have The Provision For Relocation Anywhere Easily As It Should Be An Independent Unit. Doors Should Be Assembled With Ss-304 Hinge Assembly. Removable Back Panel Should Be Provided To Easily Access The Service Lines Running Behind The Cabinet Benches. Intermediate Horizontal Channels Should Be Provided Between Door And Drawer.Shelf Should Be Eight Bend Panel With 20Mm Height. Drawer Tray Should Be Of Single Piece Construction. Drawer Should Be Well Supported On Lh And Rh Ball Slide Suspension System. Steel Door And Drawer Front Should Be Of Double Wall Construction With Sound Dampening Material Filled Inside. Doors Should Be Easily Removable, And Hinges Should Be Easily Replaceable. Knee Space Panel Should Be In 22-Gauge Construction. The Dimensions Of The Cabinets Should Be W = 450 / 600 ( As Per The Layout ) D = 530Mm, H = 635 / 485 Mm.The Entire Material Construction For The Storage Units Should Be Mscrca: Is – 513 ( 1994 ) . Thickness Of Lh / Rh Side Panels, Shutter Front, Bottom Panel, Top Front, Drawer Separator, Shelf, Alignment Channel Should Be Of 1.2Mm Thk. Removable Back Panel, Shutter Cover, Fr. Rack Strip, Top Cover Panel Should Be Of 0.8Mmthk. The Finish Of The Welded Cabinets Should Be Powder Coated Pure Epoxy Of Thickness 40-50 Microns. Handles Should Be Anodized Aluminium Recessed-Type, Of Ctc: 160.0Mm. Units Should Have A Locking Facility With 180° And 10 Lever Cam Lock Mechanism. The Hinges Should Be Knuckle-Butt Type Ss Hinge. The Screws Should Be Ss304. Shutter Should Be Of Twin-Type Construction With Sound Dampening Effect Using Profeel. Shutter Cover Should Be Equipped With Bump On For Sound Dampening. Ball Slide For Drawer Units Should Be 500Mm Length. The Worktop Should Be 19Mm ( + / - 2Mm ) Thick Jet-Black Granite Worktop. The Exposed Edges Of The Worktop Should Be Chamfered And Smoothened. The Bottom Of The Worktop Should Be Polished And There Should Be A V-Groove Throughout The Length Of The Exposed Edges To Protect The Cabinets From Meeting The Spillages. The Overhang On The Storage Cabinet Is 25 Mm At The Front Side And 30 Mm At The Sides. The Backing Material Used Is A Neoprene Mat Of 6 Mm Thickness. The Laboratory Furniture Should Meet The Performance Requirements Described In The Latest Sefa 10-2016 Class 7 / 8 Guideline For The Most Adaptive Range Of Furniture. Includingaccessories: All Fittings Should Be Powder Plated Unless Specified Otherwise. Fittings Should Be Identified With Service Indexes In The Color Coding As Per Din 12920. The Electrical Trunking Used For Housing Electrical Switches And Sockets, Data And Voice Points, Its Top Panel, Bottom Panel Of The Trunking Should Be Made From 1.0 Mm Thick Crca Ms Panel. It Should Be Available In Both, Single Sided And Double-Sided Configurations. It Should Be Made From Crca Ms With Pure Epoxy Powder Coating. , Wall Laboratory Table 1:1940 Mm L X900 Mm D X 900 Mm H Storage Based Island Bench Withshutter Drawer Under -Storage, Electrical Truncking Reagent Shelf Above The Table Top & Granite Top.Should Be Made Of Crca Ms With Pure Epoxy Powder Coating And Are Of 1Mm Thickness. The Master Upright Should Be Of The Dimensions: 300 X 150 X 1.2 Mm. It Should Be Made From 1.2Mm Thick Crca Ms With Pure Epoxy Powder Coating.It Should Have An Open-Able Door For Easy Service Maintenance And Should Extend Till The False Ceiling. The Vertical Upright Should Form The Backbone For Internal Distribution Of Gds, Electrical Supply Systems Shelves And Top Units And Should Be Constructed From 16-Gauge Crca Formed Steel Panels With Removable Covers. Shelf Height Should Be Adjustable With An Increment Of 1Inch / 25Mm. Uprights Should Be Supplied With Adjustable Feet From -5Mm To +20Mm. Depending Upon The Layout, Height Adjustable Shelves Should Be Provided Between Uprights With 1” Of Height Adjustability. The Ends And Intermediate Vertical Supports Should Be 2Mm Thick Aluminum Extrusion With Ms Brackets Of 2 Mm Thick. Toughened Glass Should Be Put-On Over These Shelves For Taking Care Of Bottle Marks / Corrosion. Suspended Welded Cabinet Body Should Be Of Flush Face Construction With Intersection Of Vertical And Horizontal Members Like Lh And Rh Side Panel Along With Front Horizontal Channel, Back Panel And Bottom Panel. The Storage Cabinets Should Be Fixed And Should Also Have The Provision For Leg Space As Per The Need. It Should Have The Provision For Relocation Anywhere Easily As It Should Be An Independent Unit. Doors Should Be Assembled With Ss-304 Hinge Assembly. Removable Back Panel Should Be Provided To Easily Access The Service Lines Running Behind The Cabinet Benches. Intermediate Horizontal Channels Should Be Provided Between Door And Drawer.Shelf Should Be Eight Bend Panel With 20Mm Height. Drawer Tray Should Be Of Single Piece Construction. Drawer Should Be Well Supported On Lh And Rh Ball Slide Suspension System. Steel Door And Drawer Front Should Be Of Double Wall Construction With Sound Dampening Material Filled Inside. Doors Should Be Easily Removable, And Hinges Should Be Easily Replaceable. Knee Space Panel Should Be In 22-Gauge Construction. The Dimensions Of The Cabinets Should Be W = 450 / 600 ( As Per The Layout ) D = 530Mm, H = 635 / 485 Mm.The Entire Material Construction For The Storage Units Should Be Mscrca: Is – 513 ( 1994 ) . Thickness Of Lh / Rh Side Panels, Shutter Front, Bottom Panel, Top Front, Drawer Separator, Shelf, Alignment Channel Should Be Of 1.2Mm Thk. Removable Back Panel, Shutter Cover, Fr. Rack Strip, Top Cover Panel Should Be Of 0.8Mmthk. The Finish Of The Welded Cabinets Should Be Powder Coated Pure Epoxy Of Thickness 40-50 Microns. Handles Should Be Anodized Aluminium Recessed-Type, Of Ctc: 160.0Mm. Units Should Have A Locking Facility With 180° And 10 Lever Cam Lock Mechanism. The Hinges Should Be Knuckle-Butt Type Ss Hinge. The Screws Should Be Ss304. Shutter Should Be Of Twin-Type Construction With Sound Dampening Effect Using Profeel. Shutter Cover Should Be Equipped With Bump On For Sound Dampening. Ball Slide For Drawer Units Should Be 500Mm Length.The Sinks Should Polypropylene Molded Construction Made Up Of 5 Mm Thick High Density And Elastic Poly Propylene With Good Resistance To Organic Solvents. Bowl Size Should Be 500 L X 400 W X 300 D Mm. The Worktop Should Be 19Mm ( + / - 2Mm ) Thick Jet-Black Granite Worktop. The Exposed Edges Of The Worktop Should Be Chamfered And Smoothened. The Bottom Of The Worktop Should Be Polished And There Should Be A V-Groove Throughout The Length Of The Exposed Edges To Protect The Cabinets From Meeting The Spillages. The Overhang On The Storage Cabinet Is 25 Mm At The Front Side And 30 Mm At The Sides. The Backing Material Used Is A Neoprene Mat Of 6 Mm Thickness. The Laboratory Furniture Should Meet The Performance Requirements Described In The Latest Sefa 10-2016 Class 7 / 8 Guideline For The Most Adaptive Range Of Furniture. , Wall Laboratory Table 2:2120 Mm L X750 Mm D X 900 Mm H Storage Based Island Bench Withshutter Drawer Under -Storage, Electrical Truncking Reagent Shelf Above The Table Top & Granite Top.Should Be Made Of Crca Ms With Pure Epoxy Powder Coating And Are Of 1Mm Thickness. The Master Upright Should Be Of The Dimensions: 300 X 150 X 1.2 Mm. It Should Be Made From 1.2Mm Thick Crca Ms With Pure Epoxy Powder Coating.It Should Have An Open-Able Door For Easy Service Maintenance And Should Extend Till The False Ceiling. The Vertical Upright Should Form The Backbone For Internal Distribution Of Gds, Electrical Supply Systems Shelves And Top Units And Should Be Constructed From 16-Gauge Crca Formed Steel Panels With Removable Covers. Shelf Height Should Be Adjustable With An Increment Of 1Inch / 25Mm. Uprights Should Be Supplied With Adjustable Feet From -5Mm To +20Mm. Depending Upon The Layout, Height Adjustable Shelves Should Be Provided Between Uprights With 1” Of Height Adjustability. The Ends And Intermediate Vertical Supports Should Be 2Mm Thick Aluminum Extrusion With Ms Brackets Of 2 Mm Thick. Toughened Glass Should Be Put-On Over These Shelves For Taking Care Of Bottle Marks / Corrosion. Suspended Welded Cabinet Body Should Be Of Flush Face Construction With Intersection Of Vertical And Horizontal Members Like Lh And Rh Side Panel Along With Front Horizontal Channel, Back Panel And Bottom Panel. The Storage Cabinets Should Be Fixed And Should Also Have The Provision For Leg Space As Per The Need. It Should Have The Provision For Relocation Anywhere Easily As It Should Be An Independent Unit. Doors Should Be Assembled With Ss-304 Hinge Assembly. Removable Back Panel Should Be Provided To Easily Access The Service Lines Running Behind The Cabinet Benches. Intermediate Horizontal Channels Should Be Provided Between Door And Drawer.Shelf Should Be Eight Bend Panel With 20Mm Height. Drawer Tray Should Be Of Single Piece Construction. Drawer Should Be Well Supported On Lh And Rh Ball Slide Suspension System. Steel Door And Drawer Front Should Be Of Double Wall Construction With Sound Dampening Material Filled Inside. Doors Should Be Easily Removable, And Hinges Should Be Easily Replaceable. Knee Space Panel Should Be In 22-Gauge Construction. The Dimensions Of The Cabinets Should Be W = 450 / 600 ( As Per The Layout ) D = 530Mm, H = 635 / 485 Mm.The Entire Material Construction For The Storage Units Should Be Mscrca: Is – 513 ( 1994 ) . Thickness Of Lh / Rh Side Panels, Shutter Front, Bottom Panel, Top Front, Drawer Separator, Shelf, Alignment Channel Should Be Of 1.2Mm Thk. Removable Back Panel, Shutter Cover, Fr. Rack Strip, Top Cover Panel Should Be Of 0.8Mmthk. The Finish Of The Welded Cabinets Should Be Powder Coated Pure Epoxy Of Thickness 40-50 Microns. Handles Should Be Anodized Aluminium Recessed-Type, Of Ctc: 160.0Mm. Units Should Have A Locking Facility With 180° And 10 Lever Cam Lock Mechanism. The Hinges Should Be Knuckle-Butt Type Ss Hinge. The Screws Should Be Ss304. Shutter Should Be Of Twin-Type Construction With Sound Dampening Effect Using Profeel. Shutter Cover Should Be Equipped With Bump On For Sound Dampening. Ball Slide For Drawer Units Should Be 500Mm Length.The Sinks Should Polypropylene Molded Construction Made Up Of 5 Mm Thick High Density And Elastic Poly Propylene With Good Resistance To Organic Solvents. Bowl Size Should Be 500 L X 400 W X 300 D Mm. The Worktop Should Be 19Mm ( + / - 2Mm ) Thick Jet-Black Granite Worktop. The Exposed Edges Of The Worktop Should Be Chamfered And Smoothened. The Bottom Of The Worktop Should Be Polished And There Should Be A V-Groove Throughout The Length Of The Exposed Edges To Protect The Cabinets From Meeting The Spillages. The Overhang On The Storage Cabinet Is 25 Mm At The Front Side And 30 Mm At The Sides. The Backing Material Used Is A Neoprene Mat Of 6 Mm Thickness. The Laboratory Furniture Should Meet The Performance Requirements Described In The Latest Sefa 10-2016 Class 7 / 8 Guideline For The Most Adaptive Range Of Furniture.

Refer document

INR 14000.0 /-

Refer document

Name of Work: Supplying, installation and commissioning of lab tables for Room no - 374 and General Laboratory Room no - 570 for Biotechnology Department at Ballygunge Science College Campus, University of Calcutta.

Sl. No.	Item Description
1	Supplying, installation, commissioning including accessories of Island Laboratory table:4870 mm L x1800 mm D x 900 mm H Island Storage Based Island Bench withShutter Drawer under -storage, Electrical Truncking Reagent shelf above the table top & Granite Top.should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The master upright should be of the dimensions: 300 x 150 x 1.2 mm. It should be made from 1.2mm thick CRCA MS with pure epoxy powder coating.It should have an open-able door for easy service maintenance and should extend till the false ceiling. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Shelf height should be adjustable with an increment of 1inch / 25mm. Uprights should be supplied with adjustable feet from -5mm to +20mm. Depending upon the layout, height adjustable shelves should be provided between uprights with 1” of height adjustability. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Toughened glass should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. The storage cabinets should be fixed and should also have the provision for leg space as per the need. It should have the provision for relocation anywhere easily as it should be an independent unit. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer.Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm.The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. The laboratory furniture should meet the performance requirements described in the latest SEFA 10-2016 class 7/8 guideline for the most adaptive range of furniture. IncludingACCESSORIES: All fittings should be powder plated unless specified otherwise. Fittings should be identified with service indexes in the color coding as per DIN 12920. The electrical trunking used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 1.0 mm thick CRCA MS panel. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating.
2	Wall Laboratory table 1:1940 mm L x900 mm D x 900 mm H Storage Based Island Bench withShutter Drawer under -storage, Electrical Truncking Reagent shelf above the table top & Granite Top.should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The master upright should be of the dimensions: 300 x 150 x 1.2 mm. It should be made from 1.2mm thick CRCA MS with pure epoxy powder coating.It should have an open-able door for easy service maintenance and should extend till the false ceiling. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Shelf height should be adjustable with an increment of 1inch / 25mm. Uprights should be supplied with adjustable feet from -5mm to +20mm. Depending upon the layout, height adjustable shelves should be provided between uprights with 1” of height adjustability. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Toughened glass should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. The storage cabinets should be fixed and should also have the provision for leg space as per the need. It should have the provision for relocation anywhere easily as it should be an independent unit. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer.Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm.The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.The sinks should polypropylene molded construction made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size should be 500 L x 400 W x 300 D mm. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. The laboratory furniture should meet the performance requirements described in the latest SEFA 10-2016 class 7/8 guideline for the most adaptive range of furniture.
3	Wall Laboratory table 2:2120 mm L x750 mm D x 900 mm H Storage Based Island Bench withShutter Drawer under -storage, Electrical Truncking Reagent shelf above the table top & Granite Top.should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The master upright should be of the dimensions: 300 x 150 x 1.2 mm. It should be made from 1.2mm thick CRCA MS with pure epoxy powder coating.It should have an open-able door for easy service maintenance and should extend till the false ceiling. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Shelf height should be adjustable with an increment of 1inch / 25mm. Uprights should be supplied with adjustable feet from -5mm to +20mm. Depending upon the layout, height adjustable shelves should be provided between uprights with 1” of height adjustability. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Toughened glass should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. The storage cabinets should be fixed and should also have the provision for leg space as per the need. It should have the provision for relocation anywhere easily as it should be an independent unit. Doors should be assembled with SS-304 hinge assembly. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer.Shelf should be eight bend panel with 20mm height. Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm.The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.The sinks should polypropylene molded construction made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size should be 500 L x 400 W x 300 D mm. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. The laboratory furniture should meet the performance requirements described in the latest SEFA 10-2016 class 7/8 guideline for the most adaptive range of furniture.