Tender For Construction Of 225 Bedded Male Barrack Block 1 At Chaibasa Police Line In The District Of West Singhbhum
Tender Value
5.30 Crore
Estimated cost
Bid Submission
16 Feb 2024
0 days left
EMD
5.31 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
chaibasa → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 225 Bedded Male Barrack Block 1 At Chaibasa Police Line In The District Of West Singhbhum
BOQ
| Sl. No. | Item Description |
| 1 | Section I Building Work |
| 2 | Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.2.7.3 Hard rock (blasting prohibited) |
| 4 | Earth filling infoundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earthobtainedfrom excavation offoundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. |
| 5 | Filling in foundation trenches and plinth layers not exceeding 150 mm thick well watered rammed fully compacted and fine dressed withearth obtained after cutting with in a lead of 50M and lift of 1.5M all complete as per building specification and directionof E/I |
| 6 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 7 | Providing designation 75A brick work inC.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 8 | Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 9 | Providing designation 100A brick work with fly ash lime brick (FLAG) conforming to IS 12894-1990 (9\"X4.5\"X3\")in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 10 | Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\"x4.5\"x3\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 11 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:2:4 (1 cement : 2 coarse sand (zone -III ) : 4 graded stone aggregate 20 mm nominal Size) |
| 12 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:1.5:3 (1 cement : 1.5 coarse sand (zone -III ) : 3 graded stone aggregate 20mm nominal Size) |
| 13 | 5.3.17.1Centering and Shuttering including strutting, propping etc. And removal of form for Foundation, footing, bases of column, etc. For mass concrete |
| 14 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 15 | Centering and Shuttering including strutting, propping etc. And removal of form for Lintel, beams. Plinth beams, girders, bressumers and cantilevers with water proof ply 12mm thick |
| 16 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 17 | Centering and Shuttering including strutting, propping etc. And removal of form for Lintel, beams. Plinth beams, girders, bressumers and cantilevers with water proof ply 12mm thick |
| 18 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 19 | Centering and Shuttering including strutting, propping etc. And removal of form for Suspended floors, roofs, landings, balconies and acces platorm with water proof ply 12mm thick |
| 20 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 21 | Centering and Shuttering including strutting, propping etc. And removal of form for Lintel, beams. Plinth beams, girders, bressumers and cantilevers with water proof ply 12mm thick |
| 22 | R.C.C. Work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, column, pillars, piers, abutments, posts and stru etc. Above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 23 | Centering and Shuttering including strutting, propping etc. And removal of form for Column, Pillars, Piers, Abutments, posts and Struts |
| 24 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 25 | Centering and Shuttering including strutting, propping etc. And removal of form for Weather shade, Chajja, corbels etc. Including edges |
| 26 | Providing and laying damp proof course 50mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand (zone III) : 4 graded stone aggregate 20mm nominal size). |
| 27 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 28 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 29 | Centering and Shuttering including strutting, propping etc. And removal of form for Stairs, (excluding landing ) except spiral staircases |
| 30 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fastenersetc.). |
| 31 | Supplying, fitting & fixing 35mm thick solid core type decorative Single leaf flush shutter with both sidedecorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes allcomplete as per building specification and direction of E/I. |
| 32 | Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 33 | 300x16 mm |
| 34 | Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive. |
| 35 | Providing Tor steel reinforcement of 6 mm dia rods as perapproved design and drawing including carriage of Rods (straight orin coils) to work site, cutting,bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position complete as per building specification and direction of E/I. (i) 6 mm dia Gr. A(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 36 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing including carriage of Rods (straight orin coils) to work site, cutting,bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position complete as per building specification and direction of E/I.(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 37 | Providing Tor Steelreinforcementof 10mm, 12mm & 16mm dia bars as per approved design and drawing including carriage ofM.S. Rods (straight or in coils) to work site, cutting bending and bindingwith annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificationand direction of E/I(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 38 | (a) 10 mm(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 39 | (b) 12 mmto 25mm (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 40 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flats as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site, hoisting as per building specification and direction of E/I. |
| 41 | Providing and fixing fan hook of 16mm diaM.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab beam at the time of casting all completeas perbuilding specification and direction of E/I. |
| 42 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps atjunctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately) : |
| 43 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium(minimum thickness of polyester powdercoating 50 micron) (Three Track) |
| 44 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be With float glass panes of 4.0 mm thickness |
| 45 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm allcomplete.9.135.2 With 12 mm mild steel U beading |
| 46 | Making plinth protection 50mm thick of cement concrete (1:3:6 ) over 75mm thick bed of dry brick ballast 40mm nominal size , well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 47 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel welded or rigedly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-chargeprofile B |
| 48 | Fixing with adjustable lugs with split end tail to each jamb |
| 49 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 50 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with foor, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 51 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in colours such as white, Ivory, Grey, fume red brown, Laid on 29 mm thick bed of cement mortar 1:4 (1cement:4coarse sand), including pointing the joints with white cement and matching pigment etc., complete. |
| 52 | Providing and laying 15 mm - 23 mm thick kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime morter (1:1:1) (lime putty : surkhi: coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 550 x 550 mm size |
| 53 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete11.41.2 Size of Tile 600x600 mm |
| 54 | Providing and laying 25mm thick white makrana marble stone slab flooring of approved quality over 19mm thick base of lime mortar (1:1:1) laid and joined with white cement slurry incluiding rubbing and polishing granolithic finish with approved quality of carborandum stone including cost of curing taxes and royalty all complete as per building specification and direction of E/I. ( 300x600mm) |
| 55 | Providing and laying 25mm thick white makrana marble tiles in risers of step skirting and pillars of approved quality over 12mm thick base of cement mortar (1:3) and jointed with white cement slurry incluiding rubbing and polishing granolithic finish with approved quality of carborandum stone including cost of curing taxes and royalty all complete as per building specification and direction of E/I. |
| 56 | Providing and laying 6 mm precast white glazed tiles in walls over 12 mm.cement morter ( 1:3 ) with gray cement slurry flush pointed with white cement including rubbing and polishing including cost of curing, taxes and royalty all complete job as per specifications and direction of E/I. (a) With \"A\" grade white 15x15 cm tiles |
| 57 | Providing 12mm thickcement plaster (1:6) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 58 | Providig 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 59 | Making 6x6mm grcoves in plaster surface over walls truly horizontal vertical as specifiedat regular intervals at all heights including cleaning finishing scaffoding and curing with all leads and lifts of water all complete as per building specification and direction of E/I. |
| 60 | Providing 12mm thick water proof cement plaster (1:3) with clean coarse sandof F.M 1.5 with 5% cico or any other approved water proofing compoind including curing carriage of water with all leads and lifts as per building specification and direction of E/I. |
| 61 | Providing two coats of oil bound distemper of approved shade & make over a primer coat of washing over new suface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 62 | Finishing Wall with acrylic smooth exterior paint of required shade : 13:46:1 New work( Two or more coat applied @1.67 lit./ 10 sq.m over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm) |
| 63 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete. |
| 64 | French spirit polishing :13.68.1 Two or more coats on new works including a coat of wood filler |
| 65 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc , by applying cement slurry mixed with water proofing ement compound consisting of applying (a) first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @0.253kg sqm .This layer will be allowed to air cure for 4 hours. (b) second layer of slurry of cement @ 0.242kg/sqm mixed with water proofing cement compoind @0.126kg /Sqm .This layer will be allowed to air cure fo 4 hours followed with water curing for 48 hours. The rate includingpreparation oof surface, treatment and sealing of all joihnts corners junctions of pipes and masonry with polymer mixed slurry. |
| 66 | Providing two coats of synthetic enamel paint of approved shade and made over steel surface including cleaning the surface thoroughly including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I |
| 67 | Grading roof for water proofing treatment with22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 20mm nominal size) |
| 68 | JSOR 2022 page no.-62 sl no. 53{M-239(ii)}Providing& supplyingCico liquid / impermo water proofing compound in cement concrete or cement mortar @2% of cement quqntity by weight ( as specified)for water proofing, including all carraige and taxes . |
| 69 | Providing 250 mm wide brick drain in cement mortar (1: 6) with av. 150 mm. clean depth and 250 mm apron including cost of earthwork involved with 75 mm, cement concrete (1: 4: 3) over one brick designation 75A, flat soling in proper grade and slope at the base, the drain duly plastered in C.M (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 70 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.(a)110 mm |
| 71 | Providing and fixing on wall face unplasticised PVC moulded fittings accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A including jointingwith seal ring conforming to IS 5382 leaving 10mm gap forthermal expansion. |
| 72 | Coupler 110mm |
| 73 | Shoe 110mm |
| 74 | Bend 110mm |
| 75 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 76 | Fly Ash Bricks |
| 77 | Bricks |
| 78 | Local Sand |
| 79 | Coarse sand |
| 80 | Stone Chips |
| 81 | Cement |
| 82 | Steel |
| 83 | Earth |
| 84 | Section - IIWater supply and sanitary installation works |
| 85 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME)Concealed work including cutting chases and making good the wall etc.. |
| 86 | 15mm dia |
| 87 | 20mm dia |
| 88 | 25 mm nominal outer dia Pipes |
| 89 | 32 mm nominal outer dia Pipes |
| 90 | 40 mm nominal outer dia Pipes |
| 91 | Providing and fixing 15 mm dia male ended brass bib cock of approved quality (wt. not less than 350 gms. ) with extra socket all complete as per specification and direction of E/I. |
| 92 | Providing and fixing 15 mm dia brass Stop cock of approved quality all complete as per specification and direction of E/I. |
| 93 | Supplying fitting and fixing the following items complete with all materials as per specification and direction of E/I.(a) Glass shelf with C.P. brass rail |
| 94 | (ii) 450x125 mm glass shelf complete |
| 95 | Providing and fixing 125 mm dia C.P. brass shower rose of 15 mm dia. Inlet etc. all complete as per specification and direction of E/I. |
| 96 | Providing and fixingG. M. fullway valve of approved quality as per specificiaton and direction of E/I. |
| 97 | 25 mm dia and weight not less than 500 gms |
| 98 | 32 mm dia and weight not less than 700 gms |
| 99 | 40 mm dia and weight not less than 1.0kg |
| 100 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 101 | Rectangular shape 453x357 mm |
| 102 | Providng and fixing on terrace (at all floor levels) polytheline water storage tank (SINTEX or equivalent quality) conforming to IS specification with fly cover lid having locking arrangement and suitable ball-valve confirming to accepted standards including all bye works. The inside surface of the tank should be white coated and out side black coated as per specification and direction of E/I complete with all taxes. |
| 103 | 3.2.1Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with100mm H.C.I. \"P\" trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/ P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixedin floor 15mm C.I. body brass spindle stop cock of weight not less than 50 grms, 15mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specificatin and direction of E/I. (a) 580 mm long with 10 ltr.low levelP.V.C.Cistern |
| 104 | Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin (Size 550 mm x 400 mm) of Parryware/ Hindustan/Nycer/Ceraor or any other I.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brasswaste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 105 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as perIS: 13983 with C.I. brackets and stainless steel plug 40 mm, includingpainting of fittings and brackets, cutting and making good the wallswherever required510x1040 mm bowl depth 178 mm |
| 106 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes. |
| 107 | 110 mm diameter |
| 108 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion. |
| 109 | (a) 110 mm single junction with door |
| 110 | (b) 110 mm H.R. Band with door |
| 111 | (c ) 100 mm H.R. Band |
| 112 | ( d ) 75 mm single junction with door |
| 113 | ( e ) 75 mm Bend |
| 114 | ( f ) 100 mmN.P Cowel |
| 115 | Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.DSR 19.6.2150 mm dia R.C.C. pipe |
| 116 | Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.DSR 19.6.3250 mm dia R.C.C. pipe |
| 117 | Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x450mm C.I . Cover with frame (weight not less than 39 Kg ) alongwith earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I |
| 118 | Supplying fitting and fixing flat back or angular lipped front vitreous white glazed earthen ware urinal of \"Hindustan parry or any other approved I.S.S make with 5 liters capacity C.I automatic fulsing cistern of reliance for any other I.S.S approved make with all fittings with C.I or R.S brackets standared size G.I flush pipe with fittings clamps 15mm C.I body brass spindle stop cock of approved quality weight not less than 400grams 15mm P.V.C /Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc all complete as per specification and direction of E/I.(a) Flat back or standing corner (600mmx350mm) |
| 119 | Section - IIISeptic tank & Soak pit ( 2 nos) |
| 120 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 121 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 122 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 123 | Providing designation 75A brick work inC.M (1:4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 124 | Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. |
| 125 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:2:4 (1 cement : 2 coarse sand (zone -III ) : 4 graded stone aggregate 20 mm nominal Size) |
| 126 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 127 | Centering and Shuttering including strutting, propping etc. And removal of form for Lintel, beams. Plinth beams, girders, bressumers and cantilevers with water proof ply 12mm thick |
| 128 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 129 | Centering and Shuttering including strutting, propping etc. And removal of form for Suspended floors, roofs, landings, balconies and acces platorm with water proof ply 12mm thick |
| 130 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I. (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 131 | Providing Tor Steelreinforcementof 10mm , 12 mm & 16 mm dia bars as perapproved design and drawing excluding carriage ofbars to work site, cutting bending and bindingwith annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificationand direction of E/I |
| 132 | 10 mm (Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 133 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 134 | Providing 12mm thick cement plaster (1:4) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 135 | Providing 1.5 mm thick cement punning including curing, carriage of water with all leads and lifts of water as perbuilding specification and direction of E/I. |
| 136 | Supplying fitting & fixing H.C.I. pipes with ear of approved make confirming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars lead and yarn for making lead caullked joints, cutting pipes to size including earth work or scaffolding where necessary etc all complete as per spectification & direction of E/I.( a ) 100 mm dia. |
| 137 | Providing and laying brick bats in soakpit with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. |
| 138 | Supplying, fitting and fixing C.I. cover with frame for mane hole and inspection chamber with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I. (a) Size 600 x 450 mm (Wt. 25 Kg). |
| 139 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 140 | Bricks( |
| 141 | Local Sand |
| 142 | Coarse sand |
| 143 | Stone Chips |
| 144 | Cement |
| 145 | Steel |
| 146 | SectionIII 200x150xmm dia Deep bore Well With Pump set & electrification etc works. |
| 147 | Suppling all materisls labour and tools and cost of drilling 200mm x 165mm bore well in all kinds of soil and rock in rural area for installation of pump set with hydrolic DTH rig machine, all complete including suplying all materials tools, drilling rig, Air compressor and equipments, as well as fuel, lubricants and cost of transprtation of Rig machine and other vehicles up to the site. |
| 148 | From 0.0M to 50.0 M belew G.L |
| 149 | From 51.0 M to200.00 M belew G.L |
| 150 | supplying all tools, tackles & lowering of 200 mm dia MS ERW casing pipe of 6mm wall thickness including welding charges, cost of pipe itc including all taxes, VAT, Excise duty, freight charges with inspection charges etc as applicable, etc all complete job. |
| 151 | Cleaning Flushing and devloping of drilled hole for testing the discharge of water development of bore well by continueous flow of water bu using heavy compresser upto satisfaction of E/I. To get uniterrupted flow of water free from sand and soil etc. |
| 152 | Supplying and fitting M.S cap over 200mm dia casing pipe as per direction of E/IFor safety of drilling bore including providing of guard for safety of the same till returned final. |
| 153 | Supplying 100 mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump. |
| 154 | Submersible Pump 150 mm dia ( with Bronze impeller) up to 8 stages2.0 HP |
| 155 | Supplying Fully Automatic Starter to operate induction motor working on 415v, 3 phase ,50 hz with no volt coil , Over load element , ON-OFF push buttons with necessary materials and connected to supply etc complete starter with original sheet steel encloser as per IS: 3914.F.A.S.D. Starter ( 10 H.P ) |
| 156 | Supplying 3 core flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed as per IS : 70983 Core 4mm thick |
| 157 | 2no heavy duty clamp 40mm dia suitable for 200 mm dia pipe with all complete job. |
| 158 | Basic rate item no. 14(K) (v) , pg no. 35Supplying & lowering 40mm da column G. I. pipe with all complete job. |
| 159 | SECTION - V ELECTRICAL INSTALLATION WORKS |
| 160 | Note- (i)PVC insuleted copper conductor cable of make:-Havell\"s/HPL/KEI/Polycab |
| 161 | (ii)PVC conduit of thikness 1.5mm/2mm for wiring:-Polycab/Klinga/Saini star |
| 162 | (iii)Switches/soket outlet for piano type:-Anchor/ Cona/Keny |
| 163 | (iv)Switches/soket outlet for modular type:-Roma(Anchor/wood)/Havell\"s(carbtree)/ Hpl/Philips |
| 164 | (v)MCB-DB, Mccb,Mcb,SFU,Changeover,Rccb:-Havell\"s/Hpl/L&T/Legrand |
| 165 | (vi)XLPE/PVC aramoured cable:-Havell\"s/polycab/capital/V-guard |
| 166 | (vii)Electrical fitting/fixtures:-Bajaj/Philips/Crompton/wipro/Hpl |
| 167 | (viii)All internal wiring work should be recessed(conseeld) |
| 168 | Point wiring in PVC conduit, with modular type switch:-Wiring for light point/fan point/exhaust fan point/call bell point with 1.5. sq.mm FR PVC Insuleted copper conductor single core cable in recessed PVC conduit, with modular type switch, pheonlic lamineted sheet,suitable size G.I.box etc. |
| 169 | Group A |
| 170 | Twin control point wiring PVC conduit with modular type switch:-wiring for Twin control point with 1.5 sq mm FR PVCInsuleted copper conductor single core cable in recessed PVC conduit, 2 way modular, switch, pheonlic lamineted sheet,suitable size G.I.box etc.as required. |
| 171 | Power plug wiring in PVC conduit(2x4 sq mm) :- Wiring for light/Power plug with 2x4 sq mm FR PVC insuleted copper conductor single core cable in recess PVC conduit along with 1 Nos. 4 sq mm FR PVC insuleted copper conductor single core cable for loop earthing as required. |
| 172 | Circuit/submain wiring in PVC conduit:-Wiring for circuit/submain wiring along with earth wire with the following size PVC insuleted copper conductor single core cable in recessed PVC conduit as required |
| 173 | 2x2.5 sq mm+1x2.5 sq mm earth wire |
| 174 | 4x6 sq mm+2x6 sq mm earth wire |
| 175 | 4x10 sq mm+2x10 sq mm earth wire |
| 176 | Teliphone wiring existing conduit:- Supplying and drawing following pair 0.5 sq mmFR PVC insuleted copper conductor, unaramed teliphone cable in existing recessed PVC conduit as required |
| 177 | 1 Pair |
| 178 | TV cable in existing conduit :- Supplying and drawing co-axial TV cable RG-6 grade copper conductor,PE insulated,withPVC sheath in the existing recessed PVC conduit as required. |
| 179 | S/F PVC conduit :-supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case recessed conduit as required . |
| 180 | 20mm |
| 181 | 25mm |
| 182 | S/F Modular boxes, base & covre plate:-following size/ modular G.I box along with modular base & cover plate for modular switches in recess etc, as required. |
| 183 | 1 or 2 module(78mm x 78mm x 45mm) |
| 184 | 6 module(78mm x 205mm x 50mm) |
| 185 | S/F modular type switch /socket :- Supplying and fixing following modular type switch box/cover including connections but excluding modular plate etc as required |
| 186 | 5/6 amps, one way switch |
| 187 | 15/16 amps, one way switch |
| 188 | 3pin 5/6 amps, socket outlet |
| 189 | 15/16 amp,6 pin socket outlet |
| 190 | Telephone socket with shutter outlet |
| 191 | TV antenna socket outlet |
| 192 | S/F Modular type electronic fan regulator:-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connectionons but excluding modular plate etc, as required. |
| 193 | S/F light plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and coverin front on recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switchconection painting etc, as required. |
| 194 | S/F power plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and coverin front on recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switchconection painting etc, as required. |
| 195 | S/F ceiling rose:-Supplying and fixing 2 pin 5 amp, ceiling rose on the existing junction box/wooden block including connection etc as required. |
| 196 | S/F Batten holder:-Supplying and fixing batten/angle holder including connection etc, as required. |
| 197 | S/F Call bell buzzer :-Supplying and fixing call bell buzzer suitable for DC/AC single phase,230 volt, complete as required. |
| 198 | ITC exhaust fan up to 450 mm, sweep:-Installation of exhaust fan up to 450 mm. sweep in the exiting opening, including making the hole to suit the size of above fan, making good the damage, connection testing commissioning etc as required. |
| 199 | S/F MCCB in cubical panel board:-Providing and fixing following rating and capacity four pole MCCB in existing panel bord,including drilling holes in cubical panelmaking connections etc as required. |
| 200 | 160 amps, 35 KA fixed thermal seting |
| 201 | S/F Busbar chamber :-Providing and fixing following capecity busbar chamber with 4 strips of suitable size of copper, heavy duty, complite with all accessosries including connections, earthing the body , etc as required. |
| 202 | 200 amps |
| 203 | S/F, panel mounting changeoverProviding and fixing following capiacity 4 pole panel mounting chengeover switches in existing cubical panel board,making connection, earthing the body etc as required. |
| 204 | 160 amps, 4 pole |
| 205 | S/F T.P.MCB DB:-Supplying and fixing following way three pole and nutral,sheet,MCB distribution board,415 volt,in recess,complete with tinned copper busbar,earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required.(But without MCB/RCCB/ISOLATOR) |
| 206 | 4 way (4+12),Double door, Horizontal type |
| 207 | 6 way (4+18),Double door, Horizontal type |
| 208 | S/F \"B\" series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, \"B\" series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 209 | 6/32 amps,single pole, \"B\" SERIES |
| 210 | S/F \"C\" series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, \"C\" series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 211 | 40 amps,TPN |
| 212 | 50/63 amps, TPN |
| 213 | S/F TPN RCCB :-Supplying and fixing following rating, double pole,(Three phase and neutral) 415 volts, residual current circuit breaker(RCCB) having a sensitivity current up to 300 milliampeares in the exiting MCB DB complete with connections, testing and commissioning etc as required. |
| 214 | 40 amps |
| 215 | 63 amps |
| 216 | P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x150mm made of mild steel, at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red coiour on front side as required. |
| 217 | Copper Earth plate electrode:-Earthing with copper earth plate 600mmX600mmX3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required. without salt charcoal or coke. |
| 218 | S/L 8 SWG copper wire ground :-Supplying and laying 8 SWG copper wire 0.50 metre bellow ground level for conductor earth electrode, including solding etc. as required. |
| 219 | P/F G.I. lightning condutor finial :-Providing and fixing of lighting conductor finial , made of 25mm dia 300mm long , G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required. |
| 220 | Pff G.I. lightning conductor tape in horizontal run :-Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Horizontal run ). |
| 221 | P/F G.I lightning conductor tape in vertical run:-Providing and fixing G.I. tape 20mm x 3mmthick on parapet or surface of wall for lightning conductor complete as required(for vertical run) |
| 222 | Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 95 sq mm but not exceeding 185 sq mmdirect in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 223 | CABLE (External electrical work) |
| 224 | S/L PVC XLPE insuletd PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts,(conforms to IS:1554, part-1) |
| 225 | 150 sq.mm. 3.5 core |
| 226 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 227 | 3½ X 150 sq. mm (45mm) |
| 228 | Providing of 15\"\" (380 mm)exhaust fan of make bajaj/havells/usha/crompton |
| 229 | Providing of 12\"\" (300 mm)exhaust fan of make bajaj/havells/usha/crompton |
| 230 | SITC of following size ceiling fan three blad confirming to IS: 374:2019 including wiring the download of standard length (upto 30 cm) with 1.5 sqmm FRPVC insulated, copper wire sutable for 230 V 50 Hz 50Hz single Phase supply etc complete as required9.4.1 1200mm (48\") Ceiling fan |
| 231 | S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722with all neccssary acc$sories as required |
| 232 | 15/16 watt LED Round Down light |
| 233 | SITC of following rate in surface mounted LED tube light fitting suitable for 230V 50HZ, single phase supply etc complete as required.9.5.220/22 W LED Tube light |
| 234 | Supplying and fixing of LED 15/16 W of make bajaj/havells/crompton |
| 235 | SITC of following rating LED street lighting luminarie with pressure die cast housing and toughened glass cover, IP 66 Protection, LUMINOUS EFFICARY>110 LM/W, with lens in existing pole/ Pipe for supply voltage 100-270 V AC, 50 HZ. Luminarie shall be confirm to IS: 10322 Par-5/ Section -3 and shall be complete with all neccessary accessories as required.90/100 watt LED Street light |
| 236 | Supplying and fixing of light class G.I. pipe of 80 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required |
| 237 | Mian Panel(LS)Power Distribution Board (PDB at GL) - Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomers and outgoing of PDB panel of 16 SWG CRCA Sheet steel IP-54 floor mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 35kA. Apporexmate size (Shall be given at the time of work order ) with front operated construction including seperate fabrication arrangement for fixing of switchgears and meters. The sheet steel under go minimum seven tanks treatement followed by finishing poder coating of minimum 60 microns thickness duly compart mentalized with locking arrangement duly fixed on base channel size 100mm X 75mm X 6mm having accessories mounted inside cubicale panel, earthing with 2 Nos. of earth studs.All opening shall be covered by soft rubber gaskit,enclosure shall be galvanished. Panel shall have suitable cable entry from top and bottom and suitable arrangement for multiruns aluminium cables for MCCB. |
| 238 | The panel includes 415V, 200A, 3Ph, 36KA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends, including connection with outgoing feeders complete in all respects. The electrolytic Aluminium bus bar of grade 63401 WP as per I:S 5082 of suitable length andinsulated by heat shrinkable sleeves Red, yellow, Blue and Black asR Y B & N.The current density of bus bar shall be minimum 0.8 A / sq mm.All inter connections from main Bus Bar to MCCB up to 100A shall be with suitable size of Bus Bar and below 100A MCCB the interconnection shall be made with 4, 6 & 10Sq mm PVC Cu. wire. |
| 239 | Incomers:- 160A, 35 kA FP MCCB adjestable thermal seting - 1 no, with front rotary handle with thermo magnetic releas160 AMPFP CHANGEOVER SWITCH 1 No.Outgoings:- 16nos-32Amps DPMCB ,SP MCB 10KA-16 Nos,3amp Auto chengeover 16 No.s, DP MCB Isoletor 4 nos,Digital Am-meter, three phase, and Digital Volt-meter, three phase 3 nos-Phase indicating light with 2 A SP MCB\"s for protection 3 nos .Make- AE / Vaishno/C&S/ CHINT 3 nos-CT 1500/5VA -5 classEpoxy resin cast CT(3 Nos.)=2 Set. Make:-Kappa / Matrix . Provisioning ofSpace for 16 nosElectronic meter in Panel+ cost of 16 gauge iron sheet to be fabricated for panel mountred switch disconnector, including bus bar chamber, insulation painting etc as required( but without bus bar copper strip)(ALL SWITCHGEARS SHOULD BELEGARAND, SCHINEDER ,SIEMENS MAKE) PANEL BUILDER MAKE- STECH POWER INDUSTRIES /,MEDITRON/TRANZITE/JMD ELECTROTECH |
| 240 | Section VI-APPROACH ROAD 25 Mtr leangth |
| 241 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:1.5:3 (1 cement : 1.5 coarse sand (zone -III ) : 3 graded stone aggregate 20mm nominal Size) |
| 242 | Excavation for roadway in soil using manual means including loading in truck for carrying nof cut earth to embankment site with all lifts and lead upto 1000 Metres. |
| 243 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 244 | Providing designation 75A one brick edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 245 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 246 | Bricks( |
| 247 | Local Sand |
| 248 | Coarse sand |
| 249 | Stone Chips ( |
| 250 | Cement |
| 251 | Section VII -LAND DEVELOPMENT (INCLUDING TOE WALL) |
| 252 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 253 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 254 | Filling in foundation trenches and plinth layers not exceeding 150 mm thick well watered rammed fully compacted and fine dressed withearth obtained after cutting with in a lead of 50M and lift of 1.5M all complete as per building specification and directionof E/I ( Mode of measurement compacted volume) |
| 255 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 256 | Providing designation 75A brick work in CM (1:6) in Foundation and plinth with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 257 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 258 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:2:4 (1 cement : 2 coarse sand (zone -III ) : 4 graded stone aggregate 20 mm nominal Size) |
| 259 | Providing 12mm thick cement plaster (1:3) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 260 | Providing 1.5 mm thick cement punning including curing, carriage of water with all leads and lifts of water as perbuilding specification and direction of E/I. |
| 261 | Providing 12mm thickcement plaster (1:6) with clean coarse sand of F.M 1.5 on inside wallincluding screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I |
| 262 | Filling infoundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earthobtainedfrom excavation offoundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. |
| 263 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 264 | Bricks( |
| 265 | Local Sand |
| 266 | Coarse sand |
| 267 | Stone Chips |
| 268 | Cement |
| 269 | Rain Water Harvesting |
| 270 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 271 | Extra for earthwork in hard soil as per specification and direction of E/I. ( Vide classificationofsoil iten _B) |
| 272 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 273 | Providing designation 75 A one brick flat soling joints files with local sand including cost of watering taxes royalty all complete as per building specefication and direction of E/I |
| 274 | Providing and laying in position cement cocrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level1:2:4 (1 cement : 2 coarse sand (zone -III ) : 4 graded stone aggregate 20 mm nominal Size) |
| 275 | Providing designation 75A brick work in CM (1:6) in Foundation and plinth with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 276 | Stone Metal at quarry site .. Traxes and royalty all complete as per building specification and direction of E/I.90 mm Gravel filling |
| 277 | 0.90 M stone Boulder filling |
| 278 | R.C.C. Work in beams, suspended floors, roofs having slope upto 15° landing, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone - III ) : 3 graded stone aggregate 20 nominal size) |
| 279 | Centering and Shuttering including strutting, propping etc. And removal of form for Suspended floors, roofs, landings, balconies and acces platorm with water proof ply 12mm thick |
| 280 | Providing 12mm thick cement plaster (1:3) with clean coarse sand ofF.M. 1.5 approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as perbuilding specification and direction of E/I. |
| 281 | Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scafolding taxes and royalty all complete as per buildings specification and direction of E/I. |
| 282 | Providing Tor steel reinforcement of 8 mm dia rods as perapproved design and drawing excluding carriage of bars to work site cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per builing specification and direction of E/I.(Onaly valid for SAIL, TATA Stee, JSPL, Electro Steel Ltd and Vizal Steel) |
| 283 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 284 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 285 | 110 mm bend |
| 286 | Shoe 110 mm |
| 287 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand)and making good the wall etc. complete(110 mm ) |
| 288 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 289 | Bricks( |
| 290 | Local Sand ( |
| 291 | Coarse sand |
| 292 | Stone Chips ( |
| 293 | Cement |
| 294 | Steel |
| 295 | Basic rate for 125/115 mm dia drilled Tube Well for drilling in all kinda of Soil and rock for installation o hand pump with DI rings all complete including supplyin all materials, labours , tools drilling rigs air compressor and equipments s well as fuel li\ubricant for making125/115 mm dia boring etc and cost of transporting rigmachine and other vechile up to site of work including contrctor profit & OH chares as per specification and directtion of Engineer Incharge(basic rate) |
| 296 | Drilling upto 30 M depth below G.L in Rulararea |
| 297 | Drillingbeyond 31 mtr upto 55 mtr below GL in Ruralarea |
| 298 | Basic rate of UPVC pipe 125 mm dia conforming o IS: latest version: |
| 299 | S/M/L forF/f wire mesh pipe |
| 300 | Add 18% GST |
| 301 | Add 1% Lebour Cess |
AI Tender Summary
Tender Timeline
Feb 06, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 16, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 17, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender