Indian Institute Of Technology-IITB has published Tender For Providing And Fixing Of Interior Fit Out Works At Tbif Of Iit Ropar. Submission Date for this Tender is 15-02-2024. Interior Work Tenders in Rupnagar Punjab. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 08-Feb-2024 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 15-02-2024 |
| Sl. No. | Item Description |
| 1 | TRIANGULAR PLY PANELING over column and table , made in wooden ply framework with 18mm ply over wooden/ ply framework. Measurement to be done for area of Exposed Surface of PLY (Area of planes A to N). No extra payment for framing to be made. All Planes named A to N as marked in Drawing No. I-107 ,F-113 to be referred to for details. Laminate to be paid separately. Compile work to be executed as per methodology in1.02 |
| 2 | Production of fabrication drawings for item no. 1.01 and seeking approval and execution methodology. |
| 3 | Supply and Installation of Factory Made Modular pantry as per drawings. The item includes cost of material delivered at site, installation, any and all accessories but not limited to soft close hardware, SS screws, all tools and tackles, for all leads, lifts and levels, provision of shop drawings, etc. all complete. as per directions of Engineer-in-charge. Carcass : 18mm pre-laminated HDHMR edge bandedShutters & Visible Panels : HDHMR 18mm finished in PVC Membrane 0.3 - 0.4 mm (as per approved shade) or Laminate Finish (edge-banded)Hardware : As per approved make Skirting : PVC Black Matte Under Counter Size - Depth 600 mmUndercounter Board: 18mm PVC BoardWorking Counter Height: 910 mm Worktop thickness with nosing: 40mm Carcass Finish Light Grey/caspani (As per approval)Undercounter Depth : 600 mm Overhead Cabinets Depth : 340 mm Laminate : Decorative textured laminate.Handleless shutters with Black Matte finished "J" profile As per Drawing No. I-104.Rates inclusive of Shop Drawings to be Prepared by Vendor and Approved by Engineer-In-Charge. Items included: Undercounter cabinets, Overhead Storages & Open shelves (if any)Items excluded: Counter-Top Stone works, Lighting/ Electrical works, Backsplash tiling, Parition Framing, Ply Panelling and Finishing in Laminate to be paid separately. |
| 4 | 60mm wide edge detail made of Edge banding and HDF(HDMR) with duco finish as per design.Paint cost will be extra as per details. (Refer Dwg I-103 c, Detail-X) |
| 5 | Providing and fixing of frameless partition consisting of 12mm clear toughened glass of approved make and fixing with WCP channel on top and bottom of glass and all the necessary fittings upto all height including silicon filling (in Glass to Glass joints and wherever required) complete job in all respects and as per the direction of Engineer-in-charge. |
| 6 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing requried door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately) |
| 7 | glass door hardware as per approved make) |
| 8 | Handle 450 mm pull handle back to back as per selection |
| 9 | Patch Lock |
| 10 | Providing & Fixing GI metal framework for Panelling/ Parition with grid of not larger than 600mm x 600 mm. All inclusive to make the panelling structurally sound. Rate shall be also inclusive of additional members to be provided at the junction of skirting / cut outs etc. All complete as per instruction of Engineer In-charge |
| 11 | Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. : |
| 12 | Hot finished welded type tubes. |
| 13 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 14 | Welding by gas or electric plant including transportation of plant at site etc. complete |
| 15 | Providing and fixing steel levelling sctrews of appropriate strength below furniture/ and or whereever specified. Fixed in Ms. Or wood with requisite hardware/screws etc. (M 10 x 15) |
| 16 | Providing and fixing BWP grade plywood with ISI mark of make Greenply / century /or equivalent used for panelling above framework cutting and fixing in necessary shapes with all the required hardware (nail, screws etc.) |
| 17 | 8 mm Ply |
| 18 | 12 mm Ply |
| 19 | Extra for creating Access Panels of size mentioned in drawings in Ply Panelling using same material (Ply + Laminate as specified) and finish using Head-capped screws |
| 20 | Providing and fixing of Water resistant HDF (HDHMR)board of density 850kg/m3 of Action tesa make or equivalent forpanelling above any surface fixed with screws/ nails or adhesive: |
| 21 | 3.2 mm |
| 22 | 6 mm |
| 23 | 8 mm |
| 24 | 12 mm |
| 25 | Providing and fixing of cement board of approved make for panelling above aluminium framework/ wooden framework/ wall fixed using screws or proper joining mechanism: |
| 26 | 8 mm |
| 27 | Providing and application of Acrylic Polyurethane coating with low Voc in matt finish applied with spray gun with minimum of 2 coats of base sealer of approved make, including application of 1st coat of primer surface (grey or white as required) mixed with thinner in ratio as specified by manufactuerer specifications with spray gun machine; followed by filling of dents, cracks or any other necessary repair with Duco soft cut putty and sanding with waterproof abrasive paper of grit 220, repeating the procedure of filling and sanding till the smooth and even surface is achieved; followed by wipe off all dust and application of 2nd coat of primer and sanding with the waterproof abrasive paper of grit 220 and followed by girt 320; followed by applicaiton of 2 coats of Duco paint after mixing the selected colour of Duco NC Lacquer with Duco thinner in the ratio specified by manufacturer. |
| 28 | PU Solid paint (of approved shade) |
| 29 | PU Solid Paint (over Metal) |
| 30 | Providing and finishing of texture paint of approved make & shade as required complete in all respect. |
| 31 | Providing three or more finishing coats of Plastic Emulsionpaint on wall & ceiling of approved make & shade as required complete in all respect . |
| 32 | Providing and application of textured laminate of approved make pasted above Ply/ any smooth surface as specified. Groove pattern to be approved by E-in-C. Assume 30% wastage for areas, where laminate is pasted on triangular planes, or diagonal grooves are proposed in Ribbon Structure. |
| 33 | 1.0 mm textured laminate |
| 34 | 1.0 mm Decorative Laminate |
| 35 | 0.8 mm laminate |
| 36 | Flooring work |
| 37 | Dismantling of existing Tile Floor . All inclusive (debris disposal , cleaning , etc).Including disposal of the debris off the campus. |
| 38 | Dismantling of existing tile Skirting. All inclusive (debris disposal , cleaning , etc).Including disposal of the debris off the campus. |
| 39 | Laying of new Tile Floor in 600mm x 600 mm polished vitrified tile of same shade as per exisiting tiles laid in the similar pattern. Including base preparation of required. |
| 40 | Dismantling / cutting / repairing / reinstalling new tiles to make provision for electrical/plumbing/civil work including skirting complete as per the direction of Engineer-in- Charge. Complete in all respects, measured in running length.Including disposal of the debris off the campus. |
| 41 | Dismantling of exisiting partition, column panelling, as and where specified in the drawings and/or as per the direction of Engineer-in- Charge. Including disposal of the debris off the campus. |
| 42 | False Ceiling Work |
| 43 | Providing and Fixing New False Ceiling Mineral Fibre 595 x 595 mmTiles in the existing Grid Ceiling wherever the existing tile/ tiles have been damaged or emptied (measured in SQM, Only Tiles to be provided and fixed). Including disposal of the debris off the campus. |
| 44 | For making provision of New points (Electrical, FF, Plumbing, ceiling supports, etc.) in GRID Ceiling including cutting, finishing etc.(measured in per point basis) |
| 45 | For making provision of New points (Electrical, FF, Plumbing, ceiling supports, etc.) in Gypsum Board Ceiling including cutting, finishing etc.(measured in per point basis) |
| 46 | Repairing of gysum board false ceilingwith New gypsum Board wherever required as per the drawings. Complete in all respects. Including disposal of debris off the campus. |
| 47 | Gypsum Board False Ceiling with 12.5 mm thick tapered edge gypsum board conforming to IS: 2095 - part I. |
| 48 | Plumbing & Firefighting Works |
| 49 | Providing and laying of waste water drain point with PVC pipes (of approved make and specifications to connect with existing waste water drain line) as per the direction of Engineer-in- Charge as per the location given in the drawings. (Refer Drawing No. A-101a for sink provisioning) (Per point basis) |
| 50 | Providing and laying of water Supply lines with CPVC pipes (of approved make and specifications to connect with existing water supply line) as per the direction of Engineer-in- Charge as per the location given in the drawings. (Refer Drawing No. A-101a for sink provisioning)(Per point basis): |
| 51 | 15 mm |
| 52 | 20 mm |
| 53 | Electrical Works |
| 54 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. |
| 55 | For Lighting Circuit/ Sub Main Wiring |
| 56 | 3 x 1.5 sqmm |
| 57 | 3 x 2.5 sqmm |
| 58 | 3 x 4.0 sqmm |
| 59 | Supplying and fixing of following sizes of conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required, including required junction-boxes |
| 60 | 25mm dia Steel Conduit |
| 61 | 25 mm dia PVC Conduit |
| 62 | Supplying and fixing suitable size GI box in fornt on surface or in recess (12 module) |
| 63 | Providing and Fixing (making connections) Modular Siwtches and Sockets, alongwith their respective Switch Plates and Covers, as per desired shade and size |
| 64 | 3 pin 5/6 A modular socket |
| 65 | 5/6 A modular switch (For Sockets and Light Points) |
| 66 | 3 pin 15/16 A modular socket |
| 67 | 15/16 A modular switch |
| 68 | Fan Regulators |
| 69 | Supply & fixing of following size (GI RACEWAY Fabricated from 1.6 mm thick GI Sheet) race ways for electrical & LV wiring including Fixing Bracket, Coupler, neoprene gasket in joints, bends, sockets cutting the floor & jaming the race way/ hanging in ceiling, supporting arrangement as approved by consultant/ architect with all necessary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification. |
| 70 | 150 mm wide x 38 mm deep. (1 Compartment) |
| 71 | 300 mm wide x 38 mm deep. (3 Compartments) |
| 72 | Providing & Fixing after making neccessary fixing provisions of metal concealed switch boxes with metal flap fitted with brush for wires access on worktop surface. Model no. DeskPort 154 Manual (8 Module), Make: Innofitt Or any equivalent model of equivalent make. |
| 73 | Supplying and drawing ofUTP 4 pair CAT 6 LAN cable in the existing surface/ recessed Steel/ PVC conduit as required. |
| 74 | Supply and installation of plug -in type data socket RJ-45 Connector outlet along with modular base and cover plate as per desired layout, color and Size of plate |
| 75 | Providing and fixing of all light fixtures |
| 76 | Supply of 12W +/-1W Deep Inset COB LED Reccess Mounted Downlighter having minimum system lumen efficacy of 90 lm/W with minimum system lumen output of 1080 lumens with Pressure Die cast aluminium housing with White Finish Trim and High transmittivity diffuser with chrome Finish reflector with deep inset White and silver bezel having P.F.>0.95 with THD<10% ,CCT 4000K ,CRI 80.The LED Fixture have minimum life of 50000 Hrs at L70.The Input voltage range shall be 100V to 265V with surge protection 2.5KV. |
| 77 | Liner Profile Recessed |
| 78 | Aluminium Linear Profile for Recess Mounting for 8mm LED Strip Lights, Internal width 11mm (Ref. Profile 1103, Model No. 833.95.722. Make Hafele or equivalent) |
| 79 | Strip to Driver Connector ribbon 8mm /24V/2.0m (Ref. Model No. 833.75.705. Make: Hafele or equivalent) |
| 80 | Flexible Strip Lights, monochrome constant current, 8mm 24V/19.2W/m 40K/CRI90/5m(Ref. Model No. 833.75.252. Make: Hafele or equivalent) |
| 81 | 24V, 0-90W, Constant Voltage Driver, Loox (Ref. Model No. 833.77.949. Make Hafele or equivalent) |
| 82 | 2 Pin EU open end Primary cable black 2000mm (Ref. Model No. 833.89.009. Make Hafele or equivalent) |
| 83 | Suspended Linear Light |
| 84 | Supply of Linear 8 Feet LED Fixture 40 W+/- 1W Suspended mounted having Extruded Aluminium housing with HET diffuserwith minimum system lumen efficacy of 115 lm/W and minimum system lumen output of 4600 lumens, P.F.>0.95 withTHD<10% ,CCT 4000 K, CRI 80.The LED with Useful life of 50000Hrs at L70. The Input voltage range shall be 140V to 300V .Fixture have Surge Protection 3kV . |
| 85 | Surface Magnetic Track Light |
| 86 | Supply of 12W +/-1W Magneto Linear Collimator Track Mounted with system lumen efficacy of 85 lm/W with Black housing with Beam angle of 36 degree having P.F.>0.95 with THD<10% ,CCT 3000K/4000K ,CRI 80s.The LEDlife of 50000 Hrs at L70.The Input voltage range shall be 150V to 270V. |
| 87 | 2 mtr Magnetic Track for Magneto Linear Collimator. |
| 88 | 90 Degree Horizontal Connector for Magnetic Track |
| 89 | Relocation of fans with all complete accessories |
| 90 | Providing and fixing Oriental Wall Fans, hi- speed 44, sweep=400mmm and white body colour. |
| 91 | Site Fabricated GI Duct |
| 92 | 24 gaugeGI Sheet Ducting |
| 93 | XLPE/Nitrile Insulation in Ducting |
| 94 | Supply and Installation of Duct Acoustic Lining |
| 95 | Supply and Installation of Aluminium Grills/Diffuser |
| 96 | Supply and Installation ofVolume control Dampers |
| 97 | Providing and Laying Carpet Tiles as per specs. Tufted High & Low loop, Face Yarn - 100% Solution Dyed Universal Nylon 6, Gauge - 1/10 Inch, Stitches - 11 Per Inch, Total Thickness - 7.5 mm (±0.5 mm), Pile Weight - 580 g/m2 (17 oz/yd2), Backing - E-Bac/PVC back, Tile Size - 50cm x 50cm/100cmx25cm |
| 98 | Providing , laying , finishing / chamferingof Wall/floor Tiles.10 mm thick tiles of approved make and colour , pasted with adhesive above Ply/ Cement Board / wall and joints filled with acid and/or alkali resisting cement as per IS : 4457 or epoxy, complete as per the direction of Engineer-in- Charge. |
| 99 | Ceramic Tiles 300 x 600 mm |
| 100 | Vitrified Tiles 600 x 600 mm |
| 101 | Providing and fixing, including chamfering & polishing of edges of Steel Grey 18mm thick granite including molding of approved shade over ply/cement board/ and other surface with epoxy resin based adhesive including cleaning etc. complete. |
| 102 | Supplying, providing, fixing with silicon toughened lacquered glass of approved shade on Ply surface. The cost isinclusive ofnecessary hardware. The item includes sealing of edges & joints with silicon sealant The works shall be completed in line and at any level to the satisfaction of Engineer-in-charge |
| 103 | 4 mm |
| 104 | 6 mm |
| 105 | Supplying,providing, fixing on studs toughened glass on vertical surface. The cost isinclusive ofnecessary hardware. The item includes cost of cutting/ holes etc. The works shall be completed in line and at any level to the satisfaction of Engineer-in-charge |
| 106 | 6 mm |
| 107 | Table made in 18mm ply with 1.2mm thk laminate finished on all exposed surfaces and 1mm laminate finish inside with 12mm thick wooden bending with soft close hafele / hettich fittings as per design.(Refer Dwg F-113 for details) |
| 108 | Seating made in MS structure of 25X50mm of 38 x 50mm pinewood slats @50mm c/c on top with clear PU paint finish. (Refer Dwg F-103 for details) |
| 109 | Planters made in MS structure of 25x50mm with 12mm thick cement board at base and 8mm thick cement board filling covering MS structure and wooden member in top edge with square groove (4x4mm) detail as per design including FRP lining inside the planters and removable water tray underneath and archi concrete (textured paint) on outer surface of cement board. Mode of measurment will be in running length. (Refer Dwg F-103 for details) |
| 110 | Made in 18mm ply with 1.2mm thk laminate finished on all exposed surfaces and 1mm laminate finish inside and 50mm solid wooden skirting with soft close hafele / hettich fittings as per design. Factory fabricated / edge band sides. (Refer Dwg F-105 for details) |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
