Purchase Of Equipment For Electronics Circuits Lab Of Instrumentation Engineering Department. , Equipment For Electronics Circuits Lab Of Instrumentation Engineering Department. , Dc Dual Power Supply ( Each Channel Separate ) ( 0 To 32V, 0 To 2A ) Specifications: Metering: 3 Digit Dpm, Meter Accuracy ±3 Counts, Constant Voltage Mode: Regulation: Line :±0.01% ±2Mv For ±10% Change In Line Output. Load : ±0.01%±2Mv For Load Change From Zero To Full Load. Ripple & Noise : 1Mv Rms Max. 20Hz- 20Mhz . Constant Current Mode : Regulation : Line ±0.1%±250?A For ±10% Line Change. Load : ±0.1%±250?A For Change In Output Voltage From 0 Volts To Maximum Output Voltage. Ripple & Noise : 0.04% Rms. Mode Indication: Led Indication For Constant Voltage / Constant Current Operating Mode. Output Priority : Floating W.R.T Ground. Overload Protection : Automatic Overload And Short Circuit Protection. Transient Response: 100?Secs To Within 10Mv Of Set Output Voltage For Load Change From 10% To 90%. Stability : Total Drift Within 8 Hours, After Warm-Up. <±0.2% Plus 5Mv In Constant Voltage Mode. <±0.5% Plus 5Ma In Constant Current Mode With Constant Line, Load And Ambient Temperature Conditions.Operating Temperature : 0-50 C. Line Voltage: 230V Ac ±10%, 50Hz, Single Phase , Dc + / -15V Power Supply ( Each Channel Separate ) ( +15V To - 15V, 0 To 2A ) Specifications: Metering: 3 Digit Dpm, Meter Accuracy ±3 Counts, Constant Voltage Mode: Regulation: Line : ±0.01% ±2Mv For ±10% Change In Line Output. Load : ±0.01%±2Mv For Load Change From Zero To Full Load. Ripple & Noise : 1Mv Rms Max. 20Hz - 20Mhz . Constant Current Mode : Regulation : Line ±0.1%±250?A For ±10% Line Change. Load : ±0.1%±250?A For Change In Output Voltage From 0 Volts To Maximum Output Voltage. Ripple & Noise : 0.04% Rms. Mode Indication: Led Indication For Constant Voltage / Constant Current Operating Mode. Output Priority : Floating W.R.T Ground. Overload Protection : Automatic Overload And Short Circuit Protection. Transient Response: 100?Secs To Within 10Mv Of Set Output Voltage For Load Change From 10% To 90%. Stability : Total Drift Within 8 Hours, After Warm-Up. <±0.2% Plus 5Mv In Constant Voltage Mode. <±0.5% Plus 5Ma In Constant Current Mode With Constant Line, Load And Ambient Temperature Conditions. Operating Temperature: 0-50 C. Line Voltage: 230V Ac ±10%, 50Hz, Single Phase , Function Generator : Wave Form Type Sine, Square, Pulse, Adjustable Duty Cycle, Precise Adjustment Of Duty Cycle, Precise Adjustment Of Duty Cycle And Period, Triangular Wave, Display 2.4 Inch Tft, Color Lcd, Operating Characteristics - All Key Operations, Knob Continuous Adjustments , Multimeter: 31 / 2 Digits, 2000Counts, Dc Voltage Up To 1000V, Ac Voltage Up To 750V. Dc Current Up To 10A, Battery Test ( 1.5V, 9V ) , Resistance Up To 2M?, Audible Continuity, Diode Test, Hfe Test ( Transistor Test ) , Data Hold, Lcd With Backlight Low Battery Indication , Genuine Arduino Uno Board ( R3 ) With Dip Atmega328 Processor , Pir Sensor For Arduino Uno, Working Voltage 5V To 20V , Dc Motor Drive For Arduino , Wheeled Robot Kit ( Arduino Compatible With Bluetooth Connection ) , Bluetooth Module For Arduino Uno , 16*2 Lcd Display For Arduino Uno , Raspberry Pi-3 ( Model B+ ) , Bcm2837b0, Cortex-A53, 64Bit Soc @ 1.4Ghz, Memory - 1Gb Lpddr2 Sdram, Access- Extended 40- Pin Gpio Header, Video And Sound: 1 Full Size Hdmi, 4 Pole Stereo Output And Composite Video Port. 4 Usb 2 Ports.
