Translational Health Science And Technology Institute-THSTI has published Tender For Providing, Supplying, Fabrication And Installation Of Wooden Furniture, Aluminium Partition Work, Sound Proofing Work And Other Misc Civil Work At Sec-10 Civil Hospital Gurugram.. Submission Date for this Tender is 03-02-2024. Civil Work Tenders in Gurugram Haryana. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Providing, fixing & installation of sound proof acoustic wall panel & Ceiling to make the room completely sound proof including making a GI frame of 50mm, filling with 50mm thick resin bounded glass whool of density 1000 GSM / 60 kg/ cum wrapped in julities clothbag (box type) and held in position using chicken mesh, 2mm black commercial grade neoprene rubber sheet, 12mm thick acoustic MDF/PLy board, UPVC track, 12mm thick PU Hd foam with fabric of required color and shade for final finish with respective seals and solvent of grooves all complete as per direction of Engineer in charge. Following Technical parameters shall follow: 1. Fire (class) - 1 & P 2. Acoustics - NRC 0.90 (for C25 Mounting) 3. Thermal Conductivity (W/mk) - 0.1 4. Climate (C, RH) - 50, 95 5. Light Reflectance (%) - 80 6. Green (VOC, RC %) - Low, 35 |
| 2 | Providing and Fixing 5mm thick mass load vinyl (MLV) sound damping sheet having a density of 2,000 kg/m3. Tested for 43 stc in 5 mm thickness with acoustic cut pile carpet 6mmof required color and shade for final finish with respective seals and solvent of grooves all complete as per direction of Engineer in charge. |
| 3 | Providing and Fixing in position 55mm to 76mm thick sandwich type composite sound reducing flush door shutters with frame of following specification : (a) Door frame shall be of teak / hard wood of size – 110 mm X 100 mm, including making necessary grooves in the frame for fixing of hollow bulb type EDPM gaskets on rebates to block noise leakage from gap in between door frame and shutter. (b) The frame of shutter shall be made from 40 mm thick teak / hard wood stiles and top & bottom rails of size 94 mm and core made of lock rail 100 mm wide and 40 mm thick and three additional strips 50 mm wide and 25 mm thick (minimum) (c) The core of door shutter shall be filled with acoustic insulation material , sound absorbing and damping material. (d) Face panels shall be of 12 mm thick Marine ply boards of approved make conforming to relevant IS codes / International Standards on both sides of the core of the shutter with required primer at the unexposed surface . One side of ply board shall be fixed to the core of the shutter along with a 5 mm thick Neoprene rubber sheet on its inner face. (e) 01 mm mica OR 04 mm thick Teak Veneer of approved make shall be bonded with 12 mm thick marine plyboard on both face of shutter by using high strength cross linked PVAC based adhesive. (f) Dropdown Seal: – Excellent quality range of Internal Automatic Dropdown Seal, which are manufactured from high grade quality raw materials. These Internal Automatic Dropdown Seal can be customized as per our precious customers specifications. These Internal Automatic Dropdown Seal are widely known for its durability and quality. Internal Automatic Dropdown Seal can be availed at industrial leading price. Resists sound upto 37db, air, insects, cold smoke, light. Designed for timber (wooden) doors. (g) Hardware- The door assembly shall be fixed to the door frame with heavy duty stainless steel hardware i.e. Door Lock, SS Bal bearing Hinges , SS door handle ‘D’ type back to back, SS Tower bolt |
| 4 | Providing, fabrication and fixing in position Sitting Working Table of below mentioned size consisting of one drawer and one shutter with two shelves on right side with leg space. Unit shall be made of 19 mm thick BWP board on top, bottom, sides, partitions, shelves, shutters and 12 mm thick BWP ply in drawer units. Supporting frame shall be made of 14 swg thick 1”x1” MS square pipe fabricated in rectangle shape on top, one bracing all-around in bottom and four legs with height adjuster. Exposed exterior surface of Board shall be finished with 1 mm thick laminate and interior surface with 0.8 mm thick laminate, edges with 4 mm thick melamine polished teak wood margin / PVC liping and MS square pipe shall be finished with synthetic enamel paint over a coat of primer. including suitable locking arrangement, screws, fasteners, hinges, adhesives, telescopic drawer channels, magnetic catchers, handles/ knobs and all other necessary fitting/ fixing arrangement etc. complete as per design, drawing and as directed by the Engineer-In-Charge. Size of table 3"6" x 2" x 2"6" |
| 5 | Providing, fabrication and fixing in position Sitting Desk of below mentioned size. Unit shall be made of 19 mm thick BWP board on top. Supporting frame shall be made of 14 swg thick 1”x1” MS square pipe fabricated in rectangle shape on top, one bracing all-around in bottom and four legs with height adjuster. Exposed exterior surface of Board shall be finished with 1 mm thick laminate and interior surface with 0.8 mm thick laminate, edges with 4 mm thick melamine polished teak wood margin / PVC liping and MS square pipe shall be finished with synthetic enamel paint over a coat of primer. including screws, fasteners, adhesives, and all other necessary fitting/ fixing arrangement etc. complete as per design, drawing and as directed by the Engineer-In-Charge. Size of table 3" x 1"6" x 2"6" |
| 6 | Providing and fixing 300mm deep over head storage cabinet fixed on the wall made of 19mm thick BWP board of approved make on top, bottom, sides, partitions, shelves, shutters.1.0mm thick laminate of approved make and shade on shutters & exposed sides of cabinets wherever required and 0.8mm thick laminets shal be fixed on all unexposed inner faces of cabintes including wooden lipping sutiable locking arrangement all type of screw fastners hinges/piano hinges, wooden screw adhesive polysing /painting of lipping , magnetic catchers towerbolts door handales/knobs and all other type of necessary fittings etc. complete as per design drawinngs and site condition as directed by engineer in-charge (Only one side front elevation area shall be measured in sqm for payment). |
| 7 | Providing, fabrication and fixing in position Work station table of size 7"11" length and 2’ wide, fixed with the wall using the MS Structure angle with fastener of required size. Made of 19mm thick BWP board, 1mm thick laminate of approved shade on all exposed faces, 08 mm thick balancing laminate on all unexposed faces, teak wood edging, including all hardware like screws, adhesives, MS Frame, Fastener all necessaryfixing arrangement etc. complete as per design, drawing and as directed by the Engineer-In-Charge. |
| 8 | Providing and fixing in position 450mm deep Wooden storage cabinets of required size consisting of two shutter with two shelves on the top and three drawer unit in the bottom over 4 wooden legs, made of 19mmthick BWP board of approved make on top, bottom, sides, partitions, shelves, shutters. 12 mm thick BWP ply in drawer unit and at back of cupboard / wardrobe as per drawing. 1.0 mm thick laminate of approved make and shade on shutters & exposed sides of cabinets wherever required and 0.8 mm thick laminate shall be fixed on all unexposed inner faces of cabinet. including wooden lipping, suitable locking arrangement, all types of screws , fasteners, hinges / piano hinges, wooden screws, adhesives, polishing / painting of lipping, telescopic drawer channels, magnetic catchers, tower bolts, door handles/ knobs and all other types of necessary fittings etc. complete as per design, drawing and site condition as directed by the Engineer-In-Charge. Size of cabinet 2" x 1"6" x 6" |
| 9 | Providing, Supplying and Fabricating Examination Table of required size Made up off of CRCA sheets having Back rest adjustable with pneumatic pump, padded with foam top in high quality washable Rexene, Provided with three drawers and three utility cabinet, Provided with foldable BP apparatus tray on the side, Provided with inbuilt foot step, Provision of saline stand, Pre treated and Epoxy coated mild steel structure including all completeas per design, drawing and site condition as directed by the Engineer-In-Charge. Size : L 1870 x W 560 x H 810 mm |
| 10 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 11 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 12 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 13 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 14 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) |
| 15 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 16 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 18 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 19 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 21 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 22 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 23 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm |
| 24 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 25 | Providing and Fixing in position wooden/PVC children friendly wall fencing of height upto 40inch made up off 8mm thick plank including openable entry door with latch, regular in shape, uniform in size, required color and shade as per drawing and all complete as per the direction of engineer in charge. |
| 26 | Providing & Fixing of 20mm thick PVC floor mat tiles, having cushioning to withstand impact, of required color, shade, size and shape including fixing, taxes all complete as per the direction of Engineer in charge. |
| 27 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall bemooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 28 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall bemooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 29 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides |
| 30 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 31 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width |
| 32 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. |
| 33 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 34 | Providing and fixing aluminium tower bolts, ISI marked,Powder coated aluminium (minimum thickness of powder coating 50 micron) required colour or shade, with necessary screws etc. complete : 250x10 mm |
| 35 | Providing and fixing aluminium hanging floor door stopper, ISI marked, Powder coated aluminium (minimum thickness of powder coating 50 micron) required colour or shade, with necessary screws etc. complete. Twin rubber stopper |
| 36 | Providing & Fixing aluminium handles (American Style) Powder coated aluminium (minimum thickness of powder coating 50 micron) required colour or shade of size 300 to 400 mm length with necessary screws etc. all complete as per the direction of Engineer in charge. |
| 37 | Providing & Fixing Sliding arrangement including all accessories for aluminium sliding door shutter etc. all complete as per the direction of Engineer in Charge. |
| 38 | Providing and Fixing of Frosted Film on glazed partitions upto required height and pattern complete as per the direction of Engineer in charge. |
| 39 | Providing and Fixing of One way Mirror Film on glazed partitions upto required height and pattern complete as per the direction of Engineer in charge. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
