|
| 1 | MATERIAL SUPPLY FOR MGNREGS WORKS |
| 2 | Quarry Waste |
| 3 | Stone Aggregate(single size): 40 mm nominal size |
| 4 | Stone Aggregate(single size):20 mm nominal size |
| 5 | Stone Aggregate(single size): 10 mm nominal size |
| 6 | Stone Aggregate(single size): 06 mm nominal size |
| 7 | Coarse sand (zone III) |
| 8 | Fine sand (zone IV) |
| 9 | Royalty for good earth |
| 10 | Royalty for sludge |
| 11 | Portland Cement |
| 12 | Through and bond stone size 24 x 24 x 39cm |
| 13 | Stone for masonry work |
| 14 | Twisted steel/deformed bars |
| 15 | Solid blocks of size 40x20x20cm |
| 16 | Solid blocks of size 30x20x20cm |
| 17 | Solid blocks of size 40x20x15cm |
| 18 | Solid blocks of size 30x20x15cm |
| 19 | Solid blocks of size 40x20x10cm |
| 20 | Hollow blocks of size 40x20x20cm |
| 21 | Hollow bloks oof size 40x20x15cm |
| 22 | Hollow bloks oof size 40x20x10cm |
| 23 | Red oxide Zinc chromate primer |
| 24 | Mild steel tubes hot finished welded type |
| 25 | Welding by electric plant |
| 26 | Galvanised steel J or L hooks 8 mm dia |
| 27 | Bitumen washer |
| 28 | G.I. Plain washer thick |
| 29 | Precoated Aluminium Trafford sheet 0.450mm thick |
| 30 | GI trafford profile sheet 0.35mm thick |
| 31 | Mild Steel round bar above 12 mm dia |
| 32 | Average rate of mild steel round bars for reinforcements |
| 33 | Mild steel plates |
| 34 | Double clip (bridge clip) |
| 35 | Single clip |
| 36 | M.S. Tube 40 mm dia |
| 37 | Binding wire |
| 38 | Galvanised wire mesh of average width of aperture 1.4 and nominal dia. of wire 0.63 mm |
| 39 | Wire nails |
| 40 | Wire mesh (rabbit) |
| 41 | Mangalore ridge tiles 20 mm thick |
| 42 | Mangalore tiles 20 mm thcik |
| 43 | PVC pipe 63 mm outer dia . 6kgf/cm2 |
| 44 | PVC pipe 63 mm outer dia. 4 kgf/cm2 |
| 45 | PVC pipe 110 mm outer dia 6kgf/cm2 |
| 46 | PVC pipe 110 mm outer dia. 4kgf/cm2 |
| 47 | PVC Elbow 63 mm dia |
| 48 | PVC 45 degreeElbow 63 mm dia |
| 49 | PVC door Elbow 63 mm dia |
| 50 | PVC bend 63 mm dia |
| 51 | PVC Tee 63x63x63 mm dia |
| 52 | PVC door Tee 63 x63x63mm dia |
| 53 | PVC vent cowl 63 mm dia |
| 54 | PVC end cap 63 mm dia |
| 55 | PVC Socket/coupling 63 mm dia |
| 56 | PVC Reducer 63x50 mm dia |
| 57 | 63 MM PVC Ball valve |
| 58 | Material - 75 mm MTA |
| 59 | Material - 75 mm valve |
| 60 | Structural steel such as tees, angles, channels and R.S. joists |
| 61 | G.I. pipes 15 mm dia |
| 62 | G.I. pipes 20 mm dia |
| 63 | G.I. pipes 25 mm dia |
| 64 | G.I. pipes 32 mm dia |
| 65 | G.I. pipes 40 mm dia |
| 66 | G.I pipes 50 mm dia |
| 67 | G.I. pipes 65 mm dia |
| 68 | G.I. pipes 80 mm dia |
| 69 | Galvanised steel corrugated sheets |
| 70 | Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots |
| 71 | Roofing paint for iron sheets in red colour |
| 72 | Solvent |
| 73 | Polyethylene water storage tank with cover and suitable locking arrangemnet |
| 74 | Flats up to 10 mm in thickness |
| 75 | Mild steel round bar 12 mm dia and below |
| 76 | 200 mm Aluminium aldrop |
| 77 | 300 mm Aluminium aldrop |
| 78 | PVC corrugated roofing sheets |
| 79 | PVC plain roofing sheets |
| 80 | Stainless steel screws 50 mm |
| 81 | Stainless steel screws 40 mm |
| 82 | Stainless steel screws 30 mm |
| 83 | Stainless steel screws 20 mm |
| 84 | Flushing Cistern P.V.C. 10 lts capacity (low level) (white) (with fittings, accessoriesand flush pipe) |
| 85 | Factory made door frame size 50x47 mm with wall thickness 5 mm made of single piece extruded profile |
| 86 | 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished) |
| 87 | Powder coated M.S. butt hinges 100 mm X58 mm X 1.9 mm |
| 88 | Bright finished or black enameled mild steel screws 40 mm |
| 89 | Bright finished or black enameled mild steel screws 20 mm |
| 90 | 100 mm S.C.I. trap with vent heel |
| 91 | White Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings |
| 92 | PVC pipe 20 mm outer dia 10 kfg/cm2 |
| 93 | G.I Limpet washer |
| 94 | Green Net 75% shade |
| 95 | GI Chicken mesh ( 24 guage 12.5x12.5mm) |
