Tender For Supply Of Led Spares For The Repair And Maintenance Of Existing Highmast Or Street Lights At Poovachal Grama Panchayat- 1 Lighting Systemmaintanance 2 90.15.4.9Supply Conveyance, Installation, Testing And Commissioning Of 100W Led Flood Light Output Greater Than 105Lumen / W 4000-6000 K With Ip 66 Protection Led Chip Make Cree / Lumilled / Nichea With Power Factor Greater Than 0.95 At Full Load, Internal Surge Protection Up To 8 Kv, And Aluminium Pressure Die-Cast Powder Coated Housing, Acrylic Cover Complete With Thd Less Than 10%, Power Factor Greater Than 0.98, Rohs Compliant, Duly Wired Up For Use On 230 V Ac Supply. Driver Compartment Should Be Seperatly Accessible For Maintenance ( Lm 79&80 Certificates From Nabl Accredited Third Party Lab To Be Produced Mentioning Chip Manufacturer ) 3 90.15.4.7Supply Conveyance, Installation, Testing And Commissioning Of 150W Led Flood Light Output Greater Than 105Lumen / W 4000-6000 K With Ip 66 Protection Led Chip Make Cree / Lumilled / Nichea With Power Factorgreater Than 0.98, Rohs Compliant, Duly Wired Up For Use On 230 V Ac Supply. Driver Compartment Should Be Seperatly Accessible For Maintenance ( Lm 79&80 Certificates From Nabl Accredited Third Party Lab To Be Producedmentioning Chip Manufacturer ) 4 90.14.1.2Fabrication, Supply, Conveyance, Installation Testing And Commissioning Of Floor Or Wall Mounting, Dustand Vermin Proof, Cubicle Type Mv Panel Board Comprising Of The Following Components / Devices &Complying To Is 8623. Fabrication Of Fully Partitioned, Dust And Vermin Proof Enclosure For Panelassembly As Per Form 4 Of Is 8623 ( With Latest Amendments ) Using Crca Sheet As Per Approved Design And Requirement, With Front And Rear Access Facility, Bus Bar Chambers, Hinged Doors For All Switch Gear Compartments, Earthing The Doors Using 4 Sq Mm Braided Copper Conductor, Providing Necessary Cut-Outs For Mounting Meters, Relays, Indication Lamps, Bus Bar Interconnection Etc, Detachable Covers For Bus Barchamber And Cable Alley, Powder Coating The Assembly After Subjecting To 7 Tank Process Etc As Required. Crca Sheet Alone Be Used For The Fabrication. Angles / Flats / Slotted Angles Etc Shall Not Be Used For The Fabrication Of Panel Assembly. The Measurments Will Be Taken The Area Of The Complete Sheets Used For Panel Board Including Partitions, Folding, Shrouding Etc.Supply And Fabrication Of Mv Panel Board Using 5 Supply And Fixing Of 1 No. Of 25 A 2 Pole Ac 1 Rated Power Contractor , 25 A Connector , 1 Nos Of Digital Timer, Suitable Copper Socket, 2.5 Sq.Mm Isi Marked Frls Pvc Insulated Single Core Copper Conductor Cable, 1.5 Sq.Mm Isi Marked Frls Pvc Insulated Single Core Copper Conductor Cable. 6 90.14.3.2 Supply And Providing Heavy Duty A Section Neoprene Gasket In The Panel Boardu Section Rubber Beeding Suitable For 1.60 / 2.00 Mm Sheet 7 90.6.5.11Supply And Drawing The Following Sizes Of Multi-Core Pvc Insulated & Frls Pvc Sheathed 650 / 1100 V Grade Copper Conductor Round Flexible Cables Conforming To Is 694 Part I 1960 In The Existing Surface / Recess Conduit As Required Including Giving Necessary Connections Of The Following Sizes.3 Core 1.50 Sq Mm 8 Supply And Fixing 4 Pole 40 A, 32Mapower Contactor In Existing Cubicle Panel 9 2.13.1Supplying And Fixing Following Rating, Four Pole, 415 Volts, Isolator In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.40 Amps 10 2.15.2Supplying And Fixing Following Rating, Four Pole, ( Three Phase And Neutral ) , 415 Volts, Residual Current Circuit Breaker ( Rccb ) , Having A Sensitivity Current 30 Ma In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.40 Amps
