Public Works Department-PWD has published Tender For Construction Of Vvip Block For The Project Of Redevelopment Ofvaigai -Tamil Naduillamoftamil Nadu House, Chanakyapuri, New Delhi. (Re-Tender). Submission Date for this Tender is 02-02-2024. Civil Work Tenders in delhi Delhi. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. |
| 2 | Centering and shuttering including strutting, propping etc. and removal of form work for : Columns, piers, abutments, pillars, posts and struts |
| 3 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: aggregate 20 mm nominal size) - 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - Hot finished welded type tubes |
| 6 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 7 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 8 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 9 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 10 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 11 | Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 12 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar |
| 13 | Dismantling doors, windows and clerestory windows (steel or wood etc.) shutter including chowkhats, architrave, holdfasts, glasses etc. complete and stacking within stacking yardin different lots one as a servicible and another as an unservicible as directed by Architect or Engineer-in-Charge. |
| 14 | Of area 3 sq. metres and below |
| 15 | Of area beyond 3 sq. metres |
| 16 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 17 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 18 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet |
| 19 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos Cement sheet |
| 20 | Dismantling the Water Supply & Sanitary lines, fittings like wash basin, EWC, IWC, urinals, Sink, SCI sanitary lines etc complete and stacking the same within 50m lead |
| 21 | Main Block |
| 22 | B - Staff Qtrs Block |
| 23 | Dismantling electrical panel boards, Genset and electrical items like fan, electrical fittings, cables, AC units, telephone cables, pipesetc complete including lawn lights and stacking the same within 50m lead |
| 24 | Main Block |
| 25 | B - Staff Qtrs Block |
| 26 | Dismantling and stacking of existing 6 passenger capacity, Ground + 1 floor landing lift machine including railing and cabin etc complete and stacking the same within 50m lead |
| 27 | 13 Passenger G+3 floor landing Lift (5 Years Old) |
| 28 | Dismantling and stacking of Centralized AC plant Hight Side and Lower Side Equipments consisting of the following units:- 1. 80 TR Voltas make Reciprocating Water Cooled Chiller Unit - 2 Nos. 2. Cooling Tower – 100 TR Heat Rejection Type, FRP Type induced Cooling Tower - 2 No. 3. Air Handling Unit - 1 No. 4.Hot Water Generator 100 KW) - 1 No. 5. Fan Coil Unit ( 1.50 TR) for Rooms along with its control valves and thermostate etc complete - 24 Nos. |
| 29 | 6. Fresh Air Washer Machine, 12000 CFM, 5 HP - 1 No. 7.Centrifugal Blower for the Exhaust System, 15000 CFM, 7.50 HP - 1 No. 8. Axial Flow Fans - 1 No. 9. MS Chilled Water with insulation and Condenser Water Lines : - Main header and Distribution lines including its control valves and accessories - 1 Lot 10. GSS Ducting for the AC air flow supply, Fresh and Exhaust line etc complete - 1 Lot |
| 30 | Dismantling, Shifting and stacking of the following Major electrical Panels complete including lawn lights and stacking the same within 50m lead . |
| 31 | a. LT Main Panel - 1 No. Incoming: 800 Amps 4 pole switch- 1 No. Outgoing: 400 Amps 4 pole switch - 2 Nos , 200 Amps TPN switch - 1 No., 800A / 5A C.T coil - 1 No. b. Main Panel - 1 No. Incoming: 400 Amps 4 pole MCCB - 1 no. C. Outgoing:200 Amps 4 pole MCCB - 1 no. 100 Amps 3 pole MCCB - 6 nos. 63 Amps 3 pole MCB - 6 nos. 400A / 5A C.T coil - 3 nos. c. 200 Amps AC Main Panel d. 250 KVA Genset along with AMF Panel and AMF Panel |
| 32 | Dismantling and stacking of Centralized Fire Fighting System such as Wet and Dry raiser MS Pipe Lines, Sprinkler system, Hydrants, Control Valves, Sprinker line, Smok Detecting System, Fire Pumps and Fire Panel etc complete (Fire panel, Pumps, Hydrants, Sprinkelrs and Smoke detectors to be handed over to the department) |
| 33 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions |
| 34 | for lead upto 10 km |
| 35 | Extra for lead beyond 10 Km to 20 Km ( Rate per km) |
| 36 | Extra for lead beyond 20 km to 30 km lead ( Rate per km) |
| 37 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. |
| 38 | All kinds of soil - Lift upto 1.5m |
| 39 | All kinds of soil - Lift from 1.5m to 3.0m depth |
| 40 | All kinds of soil - Lift from 3.0m to 4.5 m depth |
| 41 | All kinds of soil - Lift from 4.5 m to 6.0m depth |
| 42 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. Ordinary rock / Building basement rubbish material |
| 43 | Ordinary rock upto 1.5m depth |
| 44 | Ordinary rock between 1.5m to 3.00m (1 Lift extra) |
| 45 | Ordinary rock between 3.0 m to 4.5m (2 Lift extra) |
| 46 | Ordinary rock between 4.5 m to 6.0 m (3 Lift extra) |
| 47 | Ordinary rock between 6.0 m to 7.5 m (4 Lift extra) |
| 48 | Ordinary rock between 7.5 m to 9.0 m (5 Lift extra) |
| 49 | Ordinary rock between 9.0 m to 10.5 m (6 Lift extra) |
| 50 | Ordinary rock between 10.5 m to 12.0 m (7 Lift extra) |
| 51 | Ordinary rock between 12.0 m to 13.5 m (8 Lift extra) |
| 52 | Ordinary rock between 13.5 m to 15.0 m (9 Lift extra) |
| 53 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge : Hard rock (blasting prohibited) |
| 54 | 4th Lift - Depth below 6.0 m and upto 7.5m from existing ground level |
| 55 | 5th Lift - Depth below 7.5 m and upto 9.0 m from existing ground level |
| 56 | 6th Lift - Depth below 9.0 m and upto 10.5 m from existing ground level |
| 57 | 7th Lift - Depth below 10.50 m and upto 12.0 m from existing ground level |
| 58 | 8th Lift - Depth below 12.00 m and upto 13.5 m from existing ground level |
| 59 | 9th Lift - Depth below 13.5 m and upto 15 m from existing ground level |
| 60 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 61 | Removal and disposal of surplus earth by mechnical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions |
| 62 | Lead upto 5km |
| 63 | Extra for lead beyond 5 km to 10 Km |
| 64 | Extra for lead beyond 10 Km to 20 Km |
| 65 | Extra for lead beyond 20 Km to 30 Km |
| 66 | Removal and disposal of excavated rock by mechnical transport including loading, transporting, unloading to approved municipal dumping ground for the following leads for all lifts, complete as per directions |
| 67 | Lead upto 5km |
| 68 | Extra for lead beyond 5 km to 10 Km |
| 69 | Extra for lead beyond 10 Km to 20 Km |
| 70 | Extra for lead beyond 20 Km to 30 Km |
| 71 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level |
| 72 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 73 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) |
| 74 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. |
| 75 | All works upto plinth level Concrete of M40 grade with minimum cement content of 390 kg /cum . |
| 76 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. |
| 77 | All works above plinth level upto floor V level - Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 78 | All the works above floor V level for each four floors or part thereof. - Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 79 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 80 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 81 | Foundations, footings, bases of columns, etc. for mass concrete. |
| 82 | Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 83 | Suspended floors, roofs, landings, balconies and access platform |
| 84 | Shelves (Cast in situ) |
| 85 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 86 | Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 87 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). |
| 88 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). For the height upto 24.5m. |
| 89 | Height upto 5.5m. |
| 90 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level. |
| 91 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 92 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 93 | Supplying and fixing of EN8D Couplers and threading of rebars as per standard specification |
| 94 | Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. |
| 95 | (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. |
| 96 | Using rough kota stone |
| 97 | Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : |
| 98 | Using rough kota stone. |
| 99 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : |
| 100 | (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. |
| 101 | (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. |
| 102 | The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 103 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: |
| 104 | (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. |
| 105 | (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. |
| 106 | (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. |
| 107 | (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. |
| 108 | (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : |
| 109 | With average thickness of 120 mm and minimum thickness at khurra as 65 mm. |
| 110 | Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 ?45 MPa and adhesive bond strength Class R3 ?1.5 MPa. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. |
| 111 | For patching of tie rod holes, prepared tie rod hole surface and then primed the area with integral crystalline slurry @0.070kg/sqm and while the surface is tacky repair and then filled the tie rod holes with crystalline mortar@0.040kg per hole. The crystalline mortar should be tightly rodded into tie rod holes or packed tightly (For 25x25x25 mm tie rod hole, use 0.040kg to fill the hole). |
| 112 | Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. |
| 113 | 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand). |
| 114 | Extra for providing and mixing water proofing material in cementplaster work in proportion recommended by the manufacturers. |
| 115 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 116 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in :Cement mortar 1:4 (1 cement : 4 coarse sand). |
| 117 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above floor V level in :Cement mortar 1:4 (1 cement : 4 coarse sand).Extra for brick work / AAC block masonry / Tile brick masonryin superstructure above floor V level, for each four floors or part thereof by mechanical means. |
| 118 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand). Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 119 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above floor V level. Cement mortar 1 : 4 (1 cement : 4 coarse sand). Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 120 | Providing and fixing soil, waste and rainwater sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 18- 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe not more than 1.25gms/m3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with including all necessary fittings, holder bat clamps, alround PP Pipe includingbed concrete (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) ,fitted with factory fitted lip ring. |
| 121 | 40 mm dia |
| 122 | 110 mm dia |
| 123 | 160 mm dia |
| 124 | Providing and fixing floor drain with 50mm outlet and 100 mm inlet with SS grating having50mm seal for indirect floor drain |
| 125 | Providing and fixing end cap (door piece) of ppfor cleaning. |
| 126 | with 110 OD |
| 127 | with 160 OD |
| 128 | Providing and fixing PP 110mm P Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections. |
| 129 | Providing, fixing, testing and commissioning ofpipe inlet fittings fabricated with Polyproplene Pipe with maximum 3 inlets 40, 50 & 75 mm OD size Polyproplene pipe, fixed to "P" traps includingDripseal/Pipe seal/solvent /rubber ring joint complete. |
| 130 | Providing and installing Air Admittance valves with required air flow rate, including submission of design data.(McAlpine/STUDOR/CAPRICON) |
| 131 | Airflow capacity upto 26-32 l/s ( Maxi Vent ) |
| 132 | Airflow capacity upto 7.5 - 7.6 l/s ( Mini Vent ) |
| 133 | Providing & fixing of F.R.P. Grating (Heavy Duty) for channel drains including all accessoreis complete capable to bear 5.0 T Load.- 488/485 widex 40mm thk. - Drain Cover |
| 134 | Providing & fixing of F.R.P. MH Cover with frame 600 mm dia dimensions for basement sump. ( capable to bear 5.0.0 T Load ). FRP manhole cover and frame 560 mm dia |
| 135 | Providing and fixing Circular type 125 mm nominal dia stainless steel cockroach trap. |
| 136 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. |
| 137 | Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level |
| 138 | 25 mm dia, nominal bore |
| 139 | 40 mm dia, nominal bore |
| 140 | 50 mm dia, nominal bore |
| 141 | 80mm nominal bore |
| 142 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : |
| 143 | 25 mm dia, nominal bore |
| 144 | 40 mm dia, nominal bore |
| 145 | 50 mm dia, nominal bore |
| 146 | 80mm nominal bore |
| 147 | Providing, laying, testing & commissioning of "B" class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 148 | 100 mm dia, NB |
| 149 | 150 mm dia, NB |
| 150 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required |
| 151 | 80 nominal bore |
| 152 | 100 nominal bore |
| 153 | Providing and fixing brass stop cock of approved quality |
| 154 | 15mm nominal bore |
| 155 | 20mm nominal bore |
| 156 | Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 157 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931. |
| 158 | 15mm nominal bore |
| 159 | Constructing masonry chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 fine sand) for sluice valve, with C.I. surface box 100mm, to diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. |
| 160 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : |
| 161 | 65 nominal bore |
| 162 | 80 nominal bore |
| 163 | 100 nominal bore |
| 164 | Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on gyeser and solar water pipesuitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. |
| 165 | 19mm |
| 166 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. |
| 167 | 100mm dia |
| 168 | Providing and fixing of Polyethylene Raised Temperature (PE-RT) Piping system with D-2388 material as per PN-16 in accordance with ISO 10508,PERT Grade-2 for Hot and Cold water application with corresponding hot fusion welded PERT fittings in PN-16 like Tee"s, Elbows, Sockets, Reducers, Unions, brass adaptors(both male female) etc. conforming to ISO 10508 standards. Further all termination points should be brass fittings only for connection with faucets. Installation guidelines should be strictly followed as per the company"s technical literature. Further the system should bear a maximum pressure of 16 Bar at 20 Degree centigrade and a pressure of 5 Bar at 95 degree centigrade. |
| 169 | 20 mm PERT |
| 170 | 25 mm PERT |
| 171 | 32 mm PERT |
| 172 | 40 mm PERT |
| 173 | 50 mm PERT |
| 174 | 63 mm PERT |
| 175 | 90 mm PERT |
| 176 | 110 mm PERT |
| 177 | Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). |
| 178 | 15 mm dia nominal bore |
| 179 | 20 mm dia nominal bore |
| 180 | 25 mm dia nominal bore |
| 181 | Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in iverhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc. |
| 182 | Motorised butterfly valve - 50mm dia Nominal bore |
| 183 | Supply, erection, testing & commissioning of solar water heating system with following details : |
| 184 | System temperature output : 60 degree C (during clear sunny days) System type : Thermo syphon System : Non Pressurised Application : Bathing / Washing / Cooking Type of Solar Collectors : Copper tube Flat Plate Collectors as per BIS with following specifications - Size of Collector : 2080 x 1070 x 100 mm Number of Collector : To suit system requirement. Absorber area : 2 sq M Type : Cu – Cu Weight : 46 Kg (Dry) Absorber Coating : Selective – NALSUN Absorbivity : > 0.95 Emissivity : < 0.2 Frame Material : 16 SWG extruded Aluminium Glazing : Toughened Glass Glass beeding : EPDM Finish : Painted by approved shade Hot water return pump Hardware : SS 304 Insulation : PUF |
| 185 | Collector Stand : 35x35x3 mm MS angle Hot Water Tank : Cylindrical - vertical / horizontal, Stainless steel 304 grade with 100 mm thick Rock Wool insulation including 22 SWG aluminium cladding. The entire system should be complete with internal piping in SS(304)with 50 mm rock wool insulation of density 48 kg/m3with 26 SWG Al cladding, necessary isolation valves, Y type CI strainer, hardwares, temperature gauge of range 0 - 120oC, water meter, MS angle iron structure of min thickness 3 mm duly paintedetc as required to complete the system in all respects. The entire system should be approved by BIS as per IS : 12933 and as per local regulations. System Capacity : 1000 liters ( storage tank of 5,000 litres ) per day (LPD) having 10 collectors. |
| 186 | System Capacity : 1000 liters ( storage tank of 5,000 litres ) per day (LPD) having 10 collectors. |
| 187 | Supply , installation , testing & commissioningof Micro Processor Controlled air cooled Heat pumpdelivering actual capacity as per the following parameters duly installed at site. - Heat pumps shall be rated at 6.02 KW of input power and 19.8 KW of output power.Refrigerant used should be environment friendly R-410a. Heat pump should heat water upto 55°C on heat pump mode. It shall have silent operation and the sound level should not exceed 65 dB. Refrigerant R-410a/6.2 kg (Refrigerant) Heat Pump as described above Nominal Input Power - 6.03 KW Output Heating capacity - 19.8 kW All other mounting, fitting and controls Suitable for electric supply of 415 + 10 % volts & 50 hz All inter connecting wiring/cabling between heat pump and electric panel The heat pump shall have an in-built facility to start /stop depending on variation in demand at different periods |
| 188 | Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. |
| 189 | 150 mm diameter |
| 190 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. |
| 191 | 150 mm diameter |
| 192 | Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for stoMetre drainage) |
| 193 | 250 mm dia RCC pipe |
| 194 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. |
| 195 | 250 mm dia RCC pipe |
| 196 | Constructing brick masonry manholewith F.P.S.bricksin cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4gradestone aggregate 20mm nominal size); foundation concrete 1:4:8 mix(1 cement : 4 coarse sand : 8 gradedstoneaggregate40 mm nominalsize) insideplastering 12 mm thickwith cementmortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and makingchannels incementconcrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat ofneatcement completeasper standard design |
| 197 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 198 | Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 199 | Extra for depth formanhole with F.P.S. bricks |
| 200 | size 90 X 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 201 | Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 202 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar confoMetreing to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture"s peMetreanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 203 | Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design.(COVER MIN. 4.5 KG & FRAME MIN.2.7 KG ) |
| 204 | 180x150 mm size P type With FPS bricks |
| 205 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 250mm dia. |
| 206 | Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for stoMetre drainage) |
| 207 | 150 mm dia RCC pipe |
| 208 | 250 mm dia RCC pipe |
| 209 | 300 mm dia RCC pipe |
| 210 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. |
| 211 | 150 mm dia RCC pipe |
| 212 | 250 mm dia RCC pipe |
| 213 | 300 mm dia RCC pipe |
| 214 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:5 (1 cement : 5 fine sand) including 500 x 450 mm (heavy duty) precast RCC horizontal grating with frame complete as per standard design: |
| 215 | with FPS bricks |
| 216 | Earth work In excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth. 1.5m in width as per as 10 Sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. |
| 217 | All kinds of soil |
| 218 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating Each deposited layer by ramming and watering , lead up to 50 m and lift up to 1.5m. |
| 219 | Providing and laying in position cement cncrete of specified grade excluding the cost of centring and shuttering - all work upto plinth level. |
| 220 | 1:4:8 (1 cement :4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 221 | Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: |
| 222 | Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 223 | Centring and shuttering including strutting, proppintg etc. and removal of foMetre for: |
| 224 | Suspended floors,roofs, landings, balconies and access platfoMetre. |
| 225 | Edges of slabs and breaks in floors and walls, Under 20 cm wide |
| 226 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 227 | TheMetreo Mechanically Treated bars. |
| 228 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality |
| 229 | L D- 2.5 Rectangular shape 600x450mm internal dimensions |
| 230 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete. |
| 231 | Providing & fixing on wall face unplasticised -Rigid PVC rain water pipes confoMetreing to IS:13592 Tyape A included jointing with seal ring conforning to IS:5382 leaving 10 mm gap for theMetreal expansion. (i)Single socketed pipes. |
| 232 | 110 mm diameter |
| 233 | Boring/drilling bore well of required dia for casing/ strainer pipe, bysuitable method prescribed in IS:2800(Part I ), including collecting sample from different strata , preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90m depth below ground level. |
| 234 | All types of Soil - 300 mm dia |
| 235 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing (CM) pipe of required dia, confoMetreing to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. |
| 236 | 150mm nominal size dia |
| 237 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen(MetreS) pipes with ribs, confoMetreing to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. |
| 238 | 150 mm nominal size dia |
| 239 | Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 240 | Supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 241 | Supplying, filling, spreading & levelling coarse sand of size range 1.5mm to 2mm, in recharge pit, in required thickness over gravel layer,for all leads & lifts, all complete as per direction of Engineer-in-charge. |
| 242 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800(part I). |
| 243 | 100 mm dia |
| 244 | Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works |
| 245 | 25mm nominal bore |
| 246 | 50mm nominal bore |
| 247 | 80mm nominal bore |
| 248 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality |
| 249 | 25 mm dia, nominal bore |
| 250 | 50 mm dia, nominal bore |
| 251 | 80mm nominal bore |
| 252 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works |
| 253 | 25mm nominal bore |
| 254 | 50mm nominal bore |
| 255 | 80mm nominal bore |
| 256 | Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. |
| 257 | 25mm nominal bore |
| 258 | 50mm nominal bore |
| 259 | 80mm nominal bore |
| 260 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : |
| 261 | 50 mm dia |
| 262 | 80 mm dia |
| 263 | Providing & Fixing C.I.sluice valve(with cap)complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) |
| 264 | 100 mm dia.pipe |
| 265 | Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. |
| 266 | Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: |
| 267 | With F.P.S. bricks |
| 268 | Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete. |
| 269 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :. |
| 270 | 65 nominal bore |
| 271 | 80 nominal bore |
| 272 | 100 nominal bore |
| 273 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : |
| 274 | 100 nominal bore |
| 275 | 80 nominal bore |
| 276 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. |
| 277 | Providing, laying, testing & commissioning of "B" class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required |
| 278 | 100 mm dia, NB |
| 279 | 150 mm dia, NB |
| 280 | Providing and fixing G.I. pipes complete with G.I. fittings including, trenching and refilling etc. external works |
| 281 | 25mm nominal bore |
| 282 | 80mm nominal bore |
| 283 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality |
| 284 | 25 mm dia, nominal bore |
| 285 | 80mm nominal bore |
| 286 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works |
| 287 | 25mm nominal bore |
| 288 | 80mm nominal bore |
| 289 | Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. |
| 290 | 25mm nominal bore |
| 291 | 80mm nominal bore |
| 292 | Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : |
| 293 | 80 mm dia |
| 294 | Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. |
| 295 | Providing & fixing of Garden hydrant outlet consisting 1 No. 20mm dia. Ball valve, Bib cock (Brass)for connecting rubber hose, pipes & fittings including brick masonary chamber 300x300x500mm. |
| 296 | Bib Cock - 20mm |
| 297 | Ball Valve - 20mm |
| 298 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :. |
| 299 | 80 nominal bore |
| 300 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : |
| 301 | 80 nominal bore |
| 302 | RawWaterTreatment Feed Pump set: - Providing, fixing, commissioing and testing package vertical raw water pumps, comprising of Electrical Driven inline pumping with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure guage bourden type, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. |
| 303 | Pumps shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C supply & shall be having the following requirement complete with foundation and associated civil works. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve Suction & delivery header including all pipes, suction & delivery sides valves, NRV, Pressure gauges & accessories complete. Flow Rate: 3.0 LPS (1 working + 1 stand by) Head :35 M Min. Motor HP : 3.0 H.P. (Each) |
| 304 | Water Booster Pumpset(Treated Water Supply):- Supplying & supervision oftesting & commissioning of Booster Pumpset (Hydropneumatic systems) as described below |
| 305 | Package vertical Hydropneumatic system,comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inlinepumping setseach of4.0LPS to a head to 60 meterwith all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. |
| 306 | Pump mounted or wall mounted microprocessor basedcontroller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensortransmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with other RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). |
| 307 | Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP -As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & veMetrein proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheetsuitable to automatic working of above mentioned pumps. |
| 308 | Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP -As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & veMetrein proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheetsuitable to automatic working of above mentioned pumps. |
| 309 | Water Booster Pumpset (Roof Level ):- Treated Water Supply - Roof Level Booster Pump set (Hydro pneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydro pneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inlinepumping setseach of2.0LPS to a head to 25.0 meterwith all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with Pump mounted or wall mounted microprocessor basedcontroller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensortransmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. |
| 310 | Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP -As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & veMetrein proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheetsuitable to automatic working of above mentioned pumps. |
| 311 | Sump Pumps : - Supply & Installation, testing and commissioning of centrifugal non clogging submersible sump pumps for plant room drainage. Pump capable capable of handling 25 mm dia soft solids. Motor suitable for 415 + 10% volts, 3 phase, 50 Hz AC Power supply. Pumps shall be suitable for automatic/manual operation (Overall depth of sump – 1.5 M). Submersible sump pump shall be provided with dry running protection. Inclusive of supporting arrangement for stationary type. Two nos. of pump installed in one sump pit 1 working & 1 standby with automatic/manual opration as requireds. |
| 312 | Waste Water Drainage Sump Pump (3rdBasement ) Flow rate:4.0 LPS Head : 22.5 Mtrs. Min. Motor HP : 2.2 (Each) |
| 313 | Sewage Drainage Sump Pump (3rd Basement) Flow rate:4.0 LPS Head : 22.5 Mtrs. Min. Motor HP : 2.2 (Each) |
| 314 | Supplying, storing, handling, installation, testing & commissioning of Vertical Dual Media Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole, initial filling of Graded sand and gravels, pressure gauges, sampling cock, air vent, frontal MS/UPVC Piping, diaphragam valves for inlet, outlet, backwash inlet, backwash outlet drain etc. Capacity: 3.0 LPS, Working Pressure : (5 ± 2.5)MWC |
| 315 | Supplying, storing, handling, installation, testing & commissioning ofVertical Activated Carbon Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole initial filling of Activated Carbon, pressure gauges, sampling cock, air vent, frontal MS/UPVC piping, diapharagam valves for intlet, outlet, backwash inlet, backwash outlet drain etc. Capacity: 3.0 LPS, Working Pressure : (5 ± 2.5)MWC |
| 316 | Supplying, storing, handling, installation, testing & commissioning of water softening system having MSEP/FRPpressure vessel suitable for test pressure of 7 Kg/cm2 including dished end, ion- exchange resin, Frontal piping, C.I. diaphragm type valve, brine injection assembly for regeneration of softener, brine measuring cum salt water tank, inter connected flexible polypropylene MS Rubber lined (MSRL) piping, valves including provision of bye-pass arrangement complete with inside and outside painting etc. as required. Receiving, storing, handling and fixing of PVC/HDPE/FRP tank for Brine solution along with Hydraulic Injector with control valve and pipingfor brine injection. Capacity: 3.0 LPS, Working Pressure : (5 ± 2.5)MWC |
| 317 | Supplying and fixing ofPVC/HDPE/FRP tank including electrical operated metering/dosing pump for dosing of alum/sodium hypo-chlorite solutions in pipeline (all contactingparts shall be of stainless steel). Capacity - 0-12 LPH |
| 318 | Supplying & fixing of float based visual flow meter (Rotameter) suitable for water flow rate of 10800 litres per hour in the input line of water softener including matching flanges, nuts, bolts and 3 mm thick rubber insertions/gaskets complete. to assess the water flow rate in water softener. |
| 319 | Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting CompleteFlexible Pipe |
| 320 | 32mm Dia |
| 321 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : |
| 322 | Rectangular shape 453x357 mm. |
| 323 | Rectangular shape 1500x450 mm. |
| 324 | Note :The sanitaryware and CP fittings may change as per internal layout and architect consent. Out of Hagar Simpolo/ROCA/Kohler; we have selected kohler models for tentative estimate. Providing and Fixing of vitreous china single trap syphonic pattern having back inlet, supporting chair wall hung water closet withflush valve and CP brass flush bend (European type) Wall Hung water closet with seat and lid, with C.P. brass hinges and rubber buffers, adapter, rubber joints fixed to W.C., C.P. brass screwed washers including cutting and making good the walls and floors wherever required and HDPE wc pan connector including jointing with white cement coomplete inall respects. |
| 325 | Providing and Fixing of low noise Concealed cistern 120 mm ;Dual Flush - 2 litre and 4 Litre(Concealed cistern without frame ) and 03 120 06 99 (Actualtion plate -Chrome finish) |
| 326 | Providing and fixing of ABS health spary which can tolerate water pressure up to 6 bar flow pressure withsoecial durable rubber hose and holder in Polished Chrome , With Flow restrictor 6 lpm ; For green building requirement; |
| 327 | Providing and fixing of single-lever wash basin mixer ceramic having cartridge with hot water limiter including 2 flexible hoses Clean Fix S G 3/8 internal thread x 380 mm with flow volume 5 l/min independent of pressure flow pressure 0,5 - 8 bar |
| 328 | Providing and fixing of design siphon(Bottle Trap), Housing and pipes out of polished brass, easy to install by means of plug-in connection of drainpipe Comprises: ABS rosette with slide ring, cleaning aperture with O-ring seal plastic plunger Use / Technical Data: design acc. to DIN 274 Material: brass chrome, PU 1 , W: 1.28 kg/pc. |
| 329 | Supplying & Fixing ofCP soap dish Holder fixed to the wallwith PVC rubber plug with CP brass screws. |
| 330 | Providing and fixingtowel rail complete with brackets fixed with CP brass screws PVC sleeves etc. Complete. |
| 331 | Providing and fixingofC.P. brass Showerhead with showerarm and escutcheon in polished chrome . |
| 332 | Providing and fixingTowel ring withbrackets fixed to wooden cleats with C.P. brass screws. |
| 333 | Providing and fixing C.P brass central hole Shower3-in-1 Wall Mixer with Arrangement for Hand Shower & L Pipe for Overhead Showercomplete in respects. |
| 334 | Providing and fixing of stainless steel braided flexible hoses with inliner EPDM Which can bear the maximum pressure of 10 bar and maximum temperature of 90 degree Celsius with bending radius of 25 r with length 500 mm with Unionnut connection of 1/2" |
| 335 | Providing and fixing C.P. brass 15mm dia 2 in 1 Bib bib cock of approved quality confirming . |
| 336 | Providing and fixing C.P. brass Wall Mounted Sink Mixer J Pipe Spout |
| 337 | Providing and fixing of Regulating angle valve Material with filter •Filter angle valve made of Material suitablefor drinking wate, Connection: 1/2“/DN 15, Outlet: 1/2“/DN 15 Material – Brass DIN ENmade for drinking water / Noise Class I ;Chrome / Weight 0.18 Kg/St. |
| 338 | Providing and fixing Toilet Paper Holder With Flap. |
| 339 | Providing and fixing soft white color vitreous China flat back,Rectangular wall mounted wash basin with R.S. or CI bracket and 32 mm dia outlet, with brass C.P. wall cap and extension pieces, 15 mm dia C.P. brass angle stop cock with 10mm dia C.P. brass connection pipe etc.CP brass chain, CP wall flange, rubber adopter for waste connection complete, CP brass chain CP waste and CP pipe to wall with CP wall flange and rubber adopter for waste connection complete, with pedestal of matching model below wash basin, including cutting and making good the walls wherever required. . |
| 340 | Providing and fixing of Infrared sensor controlled tap With temperature controller ; battery operation with external battery compartment and 4x AA alkaline batteries including 2 flexible hoses G 3/8 int. thread x 450 mmwith backflow preventer andprefilter andflow regulator ; flow volume: max. 3 l/min independent of pressure ; can be adjusted to 1.33 lpm (For LEED) with additional areator 28 931 00 99 ; flow pressure: 0,5 - 5 bar ,max. resting pressure 8 bar. |
| 341 | Providing and fixing soft white urinals with siphon and concealed C.I. brackets, brass C.P. supply and flushing connections with 1 N0. 15 mm Dia. Brass C.P. angle type stop cock with brass C.P. wall cap,with C.P. waste coupling with C.P. wall caps brass CP cones at inlet and outlets concealed lead pipes drains form bottle trap drain pipes in floor. Joining etc complete. |
| 342 | Providing and Fixing of low noise Urinal flush valvetouch-free infrared flushing deviceMains Operated 230 V / 50 Hz with internal isolating valve. Which includes roughing in set for electronic actuation and Urinal Control finishing set. Roughing in set should comprises -plastic construction casing with cleaning cover ;pre-assembled water path with isolating valve ;sealing plug ; cleaning cover ;with Flow pressure: 0,8 - 5 bar ; • flush volume: 0,3 l/s ; 230 V 50 Hz power supply unit with mains plug • fitting connection G 1/2" (DN 15) external thread; Connection: G 1/2" ext. thread/ DN 15, andUrinal Control finishing set should comprises mounting frame with electronic module; front panel with sensor ;cartridge solenoid valve with pre-filer ;diagnostic lamps ; adjustment range; with technical data asflushing time: 2-15 sadjustable; vandal-proof design and Material: front cover out of ABS Plastic . |
| 343 | Providing and fixing Hand dryer with C.P brackets with C.P brass screws and PVC rawl plugs complete in all respects including cutting and making good the wall where required. |
| 344 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 345 | Size of Tile 600x600 mm |
| 346 | Size of Tile 1000x1000 mm |
| 347 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 348 | Size of Tile 600x600 mm |
| 349 | Size of Tile 1000x1000 mm |
| 350 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tilesgently and easily. |
| 351 | Glazed Vitrified tiles Matt/Antiskid finish of size of Tile 600 x 600 mm. |
| 352 | Providing and fixing Ist quality Vitrified wall tiles of approved make, in all colours, shades, of size 600x1200, as approved by the Architect, in dados and wall cladding, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and pointing in white cement mixed with pigment of matching shade complete (or jointing with grey cement slurry @ 3.3kg per sqm, including grouting of joints with epoxy grout of matching shade complete). |
| 353 | Stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straight Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring, stones of different finished surface texture,laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/Sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified. |
| 354 | 18 mm thickItalian Marble stone slab, Botticino, Perlato,Rosso Verona, Fire Red or Dark Emperadore etc |
| 355 | Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. |
| 356 | 18 mm thickItalian Marble stone slab, Botticino, Perlato,Rosso Verona, Fire Red or Dark Emperadore etc |
| 357 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : |
| 358 | 25 mm thick |
| 359 | Stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straight Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring, stones of different finished surface texture,laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/Sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified. |
| 360 | 18 mm thick Breccia Aurora / Grey Williams Marble stone slab or Equivalent |
| 361 | Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. |
| 362 | 18 mm thick Breccia Aurora / Grey Williams Marble stone slab or Equivalent |
| 363 | Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. |
| 364 | 18 / 12 mm thick Grey arabico Marble stone slab or Equivalent |
| 365 | Inlay work of floral motif or motif inspired by padi kollam by machine / manual for stone work in Wave Pattern/ Geometric Design Pattern/ Abstract Pattern, Linear Pattern Straight Pattern as per Design/ Drawing. Machine cut, mirror/ diamond polish, Marble Combination stone work in Flooring andsteps etc., stones of different finished surface texture,laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Architect/ Engineer-in-Charge.(The cost of protecting stone work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item) |
| 366 | 18 mm thick Italian, Marble stone slab,of any kind.Stone to be approved by Architect/ Engineer/Owner |
| 367 | Providing and fixing Carpet flooring using Carpet Tile of approved make, shade and pattern and of the following specification: High Cut – Low Loop Carpet tile, Premium Solution Dyed Nylon with Anti Stain Treatment, 1/10 gauge, minimum Pile height should be 8.0mm Cut and 3.5mm Loop or with acceptable tolerance, total minimum thickness 9.0mm, Tile size should be minimum 500mm x 500mm, Secondary Back Commercial 100% Re-cyclable. Wear Warranty– product should be warranted for10 Year Warranty with minimum weight loss of pile and colour. All yarns used are Solution dyed to minimize use of water and exclude any effluent production. |
| 368 | Providing and laying 19-20mm hardwood flooring as per approved pattern and design by the architect/ Engineer in charge. The flooring is to be pre-finished with multiple protective layers of tough, scratch resistant, UV cured acrylic with embedded anti-scratch and having long lengths to create a floor that offers uninterrupted visual beauty and is Eco Friendly. The Flooring should be manufactured in Europe. |
| 369 | Providing and fixing at site 14mm thick 100mm high hardwood groovedskirting/trim all complete as instructed byengineer in charge. The hardwood skirting/trim should be manufactured in Europe. |
| 370 | Providing and laying at site 10-13mm thick engineered wood flooring with specially developed core: having patented click system perfect fold joints to secure long lasting joint. The planks shall be placed on an under lay of 0.2mm thick alkali resistant polyethylene sheet. All as per manufacturer specification. (The cost of protecting Wooden Flooring work with polythin and a layer of POP or by any other mean as required to be included in the quoted price of this item). |
| 371 | Providing and fixing at site 10mm to 13mm thick 100mm high laminated wooden skirting/trim all complete as engineer in charge. |
| 372 | 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 373 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 374 | Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye, Armani Green & Kandla grey Borderor equivalent.Quartzite Flooring |
| 375 | Entry Mat System Providing & Fixing entrance matting (Heavy Duty) with enhanced absorption. Construction - Looped pile carpet design with solid vinyl backing. Material - Polypropylene & Nylon with vinyl backing. Size - Standard/ as per site in charge. |
| 376 | Providing and laying 20mm artifical green grass over finish surface without any adhesive. |
| 377 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : |
| 378 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent Quartzite Flooring |
| 379 | Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). |
| 380 | White sand stone - 30mm thick gang saw cut stone |
| 381 | Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Outter marble stone moulding and cladding |
| 382 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias, skerting,dedo and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 383 | Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye, Armani Green & Kandla grey Border or equivalent.Quartzite Flooring Area of slab upto 0.50 sqm. |
| 384 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 385 | Marble Work |
| 386 | Granite work |
| 387 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 388 | Extra For Providing-V- Groove of Size 6 x 6 mm in Stone Wall Liningat all levels as per architect drawing. |
| 389 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 390 | Second class teak wood |
| 391 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 392 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 393 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 394 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately): - 35 mm thick shutters - Second class teak wood. |
| 395 | 35 mm thick shutters |
| 396 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 397 | 75x47x1.80 mm |
| 398 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : |
| 399 | 125x64x2.50 mm |
| 400 | 75x50x2.50 mm |
| 401 | Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : |
| 402 | 125x85x5.5 mm (heavy type) |
| 403 | 100x85x5.5 mm (heavy type) |
| 404 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : |
| 405 | 50 x 20 mm |
| 406 | Supply and fixing ofpull Handleback to back with 305mm CTC, adjustable fixing for glass, wood and metal doors in brass finish. The pull handles should have supporting washer with raised beveling on the outer surface. Length = 350mm. |
| 407 | Providing and fixing antique finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 408 | Providing and fixing Antique bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 409 | Providing and fixing Antique bright finished brass tower bolts (barrel type) 300x12 with necessary screws etc. complete : |
| 410 | Providing and fixing of Antique brass door buffer with magnetic catcher. |
| 411 | Providing and fixing overhead cam action door closer with adjustable closing force EN2-4.all as per specifications. |
| 412 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 50 kg and door width upto 1000 mm), with necessary accessories and screws etc. complete. |
| 413 | Second Class Teakwood handrail approx 900mm high togeather with 75mm dia decorative curved teakwood post apoxy grouted to tread with 12mm dia S.S rod in sleeve embedded in RCC at approx third tread infilled with 12mm thick teakwood jalli of specified patteren fixed in between baluster, 40x6mm SS plate screwed to teak wood blauster to receive 85x65mm teak wood curved hand rail with and including polishing of teakwood hand rail.All work complete as shown in drawing. |
| 414 | Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 415 | Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.) |
| 416 | Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.) |
| 417 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). |
| 418 | Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). |
| 419 | Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge - Sealant 25mmx10mm at joints. |
| 420 | Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. |
| 421 | Sal wood |
| 422 | Providing and fixing non load bearing fixed frame for fire resistant glazed Partition for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20 minutes of insulation (EI20).The profile has to be fixed to the supporting construction by means of anchor fasteners of size M10 x 80, every 150 mm from the edges and every 500 mm (approx) c/c. Linear measurement of frame shall be measured for payment. The frame shall be filled with mineral wool insulation of density min 96kg/ m³. and finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer - in- charge. |
| 423 | Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm. |
| 424 | Solid block wood work for architectural and design aesthetics on all floors of the building. Solid wood large sections to be used for making cornices and mouldings on all floors at the junction of ceiling and vertical wall as per design and drawing. Architectural solid wood section work for ceilings frames of size 150x100 on all floors ceiling. Solid wood work for wooden artifacts, murals and motifs as per design and drawing. All solid works may required lathe work on wood chiseling work on solid wood and machine/manual work on solid wood for al architectural work as per drawing design and directions. |
| 425 | Second class teak wood |
| 426 | Supply and Installation of Automatic sliding door operator Automatic sliding door Set 1 operator as per approved dwg. Compliant with European standards .Product should be TÜVtest certifiedfor 1 Million cycles , tested according to the low voltage guidelines & operator unit power consumption not exceeding 100 W/Hr. , fulfils DIN 18650 standards. The track profile should be flexible for both surface mounted & ceiling hung application with additional profile for vibration & sound dampening feature. It should includes micro processor controlled drive unit, with self learning mechanism, program selector with knob, motion detection sensor – 2 nos , 1 on each side ,including passage safety combi-sensor on one side , mechanical components, toothed belt, cover profile not exceeding 110mm visible H, floor guide for frameless glass (02 nos), glass clamping rail (02 nos), Body finish : standard silver anodized operator profile electromechanical lock with 12 mm plain toughened frameless glass for complete elevation - 2 moving panels. UPS of 750 VA shall be provided by others, which will give power backup of 20 min. Only & if the duration of power cut to the operator is more than 30 min., then separate arrangement needs to be done for the same as automatic operator requires uninterrupted stabilized power supply. it should include Wall Corner Protection. (WCP) |
| 427 | The above work complete in all respect as per approved drawings and to the satisfaction of Architect. 2000X2400 |
| 428 | Providing and fixing 12 mm thick frameless toughened glass door shutter with glass of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Architect (Cost includes providing & fixing of Door handle, lock . top patch , bottom patch , Floor Spring Top and bottom pivot and stopper).(one set of hardware for one door. payment in Sqm of door size. minimum width of door 0.9 mtr). |
| 429 | Designing the SemiUnitised Structural Glazing Systemas per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the Particular specification (Methodology should be got approved by the dept officials).Design the framing system (ie.Male & Female frame) to support Vision panels, Spandral panels either with Glass or Aluminium composite panel, openable window panels on a continuous framing supported between floors.Also design the split framing unitised glazing system in case of Strip or Punched windows with vision panel proposed with either Insulated / Monolithic Glass. Groove width in the system both in horizontal and vertical shall not be more than 20mm.Glazing of panel shall be done only at factory at the controlled atmosphere. Vertical in-situ glazing shall not be carried out during construction / erection stage. |
| 430 | a. Design: Design pre-assembled aluminium semi Unitised Structurally glazed Panel / strip / punched window system to any shape and profile to with stand a design wind pressure (Test pressure shall be 1.5 times of the design wind pressure) conforming to IS 875 - Part-3 and Lateral forces as per IS 1893 (Latest Revision) and fixed at horizontally / vertically / sloped / curved position etc as shown in the drawing by using Aluminium extrusion, Glass, Spacer tape, Gasket and Sealant as specified. System shall be designed with Air Pressure equalization chamber and concealed continuous gutter vertically and horizontally at all levels as self drainage barrier to achieve water tightness besides providing EPDM Gaskets as air & water barrier. |
| 431 | b.System: System shall be designed to withstand a design wind pressure specified above with self-bearing modular elements supported between floors, EPDM Gaskets to prevent the system from Air & water penetration , double adhesive spacer tape, backer rod, sealant, supporting brackets (Resistance to design wind pressure), Seperator Gaskets for Bi-Metallic Corrosion, Pressure equilization chamber in the system, built-in continuous internal drainage gutter for collection and facility at lowest floor level to drain out penetrated water, in built adjustability to accomodate thermal expansion,thermal movement and movement due to any other forces. System shall be designed with open groove joint system and the aluminium member and Sealantshall not be visible on the external surface except colour anodised aluminium holder to the required width and thickness as per design at bottom of panel as Dead load support to the Glass panel. |
| 432 | c. Movement : System shall be designed to accommodate movement due to anyforce including the movement resulting from the exterior skin temperature ranging from 15to 85 deg.celsius, Interior skin temperature ranging from 15to 30 deg.celsius, and also to accommodate the horizontal building movement of 10 mm per panel & vertical movement of 20 mm between floors on the aluminium framing system with support brackets, glass, gaskets and fastening devices. System shall be designed to accommodate the size and shape of the glass panels as per the approved drawings including approved modifications as may be required during execution as well as all other incidental forces and stresses likely to be experienced under service conditions, i.e. Lateral force, Dead weight and Thermal expansion due to building movement both vertical & horizontal etc. |
| 433 | II. MATERIALS: |
| 434 | a.Frames: Providing and fixing pre-assembled aluminium frame work (Main & child frame) designed to with stand design wind pressure and movements as specified as continuous framing system for Structurally glazed panel and split framing system for structurally glazed punched windows. Horizontals (Transom) shall be made out of specially designed extruded sections matching to the Mullion depth in such a way the Mullion and Transom flush on inside of the facade. Fabricated Mullion and Transom shall be fixed at all levels and heights as per approved shop drawing into masonry wall / RCC surface with supporting system consisting of Brackets / Clamps, fastening straps, nuts, bolts, rivets, washers and other fastening materials. Extruded section shall be designed to accomodate Insulated Glass (DGU) / Monolithic (Single) Glass and Aluminium composite panel as per the approved shop drawings. Extruded sections shall be 22843 & 22739 (H9) grade conforming to BS 4174 or IS 8147, finished with AC15 grade Architectural quality electrolytic colour anodic coating of approved colour - IS 1868. |
| 435 | b.Glass: Providing and fixing Insulated Glass (DGU) - 24 mm thick (6mm ST 767 or 750 Toughenedglass - as approved by theDepartmental officers +12mm air + 6mm clear toughened glass) / Monolithic (single) Glass - 6 mm as per specification below for both vision and spandrel panel conforming to the minimum spectral parameters as specified. Spacer for Insulated glazing unit shall be aluminium extruded profile and finished with AC 15 grade electrolytic colour anodic coating of black colour conforming to IS 1868 and filled with dry desiccant. Primary sealant shall be Poly-isobutylene (PIB) and Secondary seal shall be structural silicon sealant of DC 995 (one part) or DC 983 (two part) of Dow corning or approved equivalent. Make and thickness of Inner pane glass shall be the same as outer pane glass of DG unit. |
| 436 | c. Processing of Glass : Details of the processor and their facilities should be submitted to the Employer/PMC/Architect for approval. Insulated glazing unit shall be processed only by the approved Processor. All glass panes used in the glazing shall be heat strengthened conforming to ASTM C 1048. No tong marks shall be allowed in the processed glass. Necessary test certificate shall be produced by the processor to confirm the adherence of the parameters set out in the codes and standards. New substrate glass shall only be used for coating and to ensure the same, a certificate shall be produced by the contractor. Necessary clearance from the processor shall be arranged by the contractor for the inspection of Employer/PMC/Architect of the glass processing plant during the progress of glass processing. |
| 437 | d.Gaskets: Providing and Fixing Ethylene Propylene Divine Monomer (EPDM) Gaskets as weather strip andbarrier at minimum 3 stages to ensure water and air tightness. Weather strip shall be EPDM Gaskets with shore 61/71 Grade of Sai rubber make or Osaka rubber make or approved equivalent. Necessary test certificate shall be produced by the Contractor. |
| 438 | e.Sealing: Providing and applying the structural sealent for the glazing at factory confirming to the thickness & bite of sealants as designed & determined by calculation, verified and tested by Manufacture"s of sealant. Bite and thickness shall be designed to withstand 3 times of the stress caused by the design wind pressure and the Design calculation of sealant manufacturer shall be produced along with shop drawing for approval.Supplying and fixing the Double Adhesive spacer tapes for glazing the panel at factory shall be open cell polyethlene and it shall be approved tapeequivalant. Jointing / Sealingshall be done with Non structural (weather) sealant / Non staining sealent of DC 789 HP of Dowcorning make or approved equivalant with Polyurethene baker rods of Supreme make or approved equivalant. Acetoxy sealent shall not be used for Structural Glazing application. In general, the type of sealant shall be as follows: |
| 439 | Shop / Factory Sealants : i) Structural sealant shall be DC 995 (one part) ii) Non-Structural (weather) sealant shall be DC 789 HP of Dow corning make(one part) or approved equivalent. Colour - Grey or Black colourii) Non-Structural (weather) sealant shall be DC 789 HP of Dow corning make(one part) or approved equivalent. Colour - Grey or Black colour |
| 440 | FieldSealants : i) Structural Sealant shall be DC 789 (one part) or DC 995 (one part)of Dow corning make or approved equivalent. ii) Non-Structural (weather) sealant shall beDC 789 HPof Dow corning make or approved equivalent. Colour - Grey or Black colouriii) Structural anad non structrual sealent (weather) sealantdow corning or approved equivalent Colour - Grey or Black colour |
| 441 | i.Top Hung windows: Providing and fixing the shutter with Multi point locking handle without key - Model no 610 KH at centre of the transom having a size of 110 x 27mm of Aluhalpha make or approved equivalant and shall made out of aluminium die cast with powder coat finish - 65 microns,matching to the transom profile colour. Rate shall include the shutter frame as designed, EPDM gaskets, all hardwares like hinge, stay and handle with key, fastening materials, all other necessary materials etc. |
| 442 | j.Off-Site proto type Test: Provide shop drawings and design calculation to carry out the full Scale off site proto type at an approved Laboratary in india based on the Design Criteria set out in the Technical specification and confirming to ASTM E 330. Methodology along with shop drawing shall be submitted for the approval of Employer/PMC/Architect. |
| 443 | Conduct full scale off-site proto type test as per design creteria set out in the Technical specification and confirming to the standards as per ASTM E 330. Necessary clearence from the Laboratary to inspct the test and the contaractor shall arrange for the inspection of Employer/PMC/Architect to witness the test during the test is in progress including the expenses incurred for the Inspection of the team. If off-site proto type test fails, correct the defects revealed to the satisfaction of the performance data as set out in the Technical Specification with prior approval of Employer/PMC/Architect on defects rectification Methodology. Upon approval of methodology retesting shall be done at laboratory to the satisfaction of the performance data as set out in the Technical Specification with prior approval of Employer/PMC/Architect. Any charges on account of rectification of test specimen and test rig due to failure of the test shall not be paid for. |
| 444 | l.General Guideline: System design in total, including Aluminium extruded frames, type & thickness of Glass pane, Aluminium sleeves at connections, inserts, EPDM Gaskets, Adhesive tapes, Sealant, Supporting system / bracket including fastening and anchoring system & Materials specified in the schedule and the system details as shown in the tender drawing are only tentative and is meant to set out a general outline of the Proprietary system. Since the Structural Glazing system in terms of Design, materials, all fixing details, methodology of execution are proprietary in nature, the onus of the design and Performance requirements, shop drawing, execution etc satisfying the design intent, particular specification and site conditions lies solely with the Contractor. |
| 445 | m. Mode of Measurement: Length and breadth (Sqm Items) of the superficial area of the finished work shall be measured centre to centre of the grooves on the external surface viewed externally correct to a centimetre under the respective items. Areas shall be calculated in a square metre correct to two places of decimal. Glass area including groove (i.e. centre to centre of groove line both horizontal and vertical) on the external surface only will be measured under respective item and paid for.Openable area measured to two times of measurement.Quoted rate shall be deemed to have considered the above stipulation. |
| 446 | n. Rate. Quoted rate shall include the cost of all materials and labour involved in all the operations as specified above, specified in the external facade system, to execute the work as per approved drawings / shop drawings including, scaffolding, infrastructure facility, tools and plants etc. necessary for execution of the respective item for all height and for all floor levels. Item measurable in sqm shall exclude cost of off site proto type test item and supply of glass, but includes the cost of field test. Supply of Glass and off site proto type test shall be measured separately and paid under respective item number. |
| 447 | SemiUnitized Structural glazing system and Associated works : Quote rate for complete system as mentioned above for the items covered below including glass fixing, INCLUDINGcost of glass,etc., |
| 448 | Note : The following perfomaance test are to be conducted on sstructural glazing system if areaa of structural glaazingg exceeds 2500 sqm from the certified llaborattories accrediated by NABL (National Accrediation Board for Testing and Calibration Laboratories), Department of Science & Technologies India.. Cost of testting is payable separately. The NIIT approving authority will decide the necessory of testing on the basis of cost of the work, cost of the test and importance of the work. Performance TTesting ofStructural glazing system tests tto be conducted in the NBL Certifies laboratories. 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200mVhr. 2. Stataic Water Penetration Test. (50pa to 1500pa) as per AStTME-331-09 testing method for a range upto 2000ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAAMA 501.01- 05 testingg method for a range uptto 2000ml. 4. Structuraal Performaance Deflection and deformation by static air pressure test (1.5 times desing winf pressure without any failure) as per ASTME-330-10 testing methodfor the raange upto 50mm. 5. Selsmic Movement Test (upto 30mm) as pere AAMA 501.4-09 testing method for Qualitative test Tests to be condducctedd on ssite. 6. Onsite Test for Water leakagge for aa pressure range 50kpa to 240kpa (35psi) uptto 2000 ml. |
| 449 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 450 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 451 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses,frames etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. |
| 452 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 453 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, |
| 454 | including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing |
| 455 | compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 456 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). |
| 457 | 12.5 mm thick tapered edge gypsum moisture resistant board. |
| 458 | Providing and fixing Gl Clip in Metal Ceiling System (wooden Finish) of 600x600 mm module which includes providing and fixing "C" wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : |
| 459 | GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 460 | Supply and Installation of Polylam Linear Curve Baffle Ceiling System comprising custom made curved rafters with varying depths ranging from 100-300mm deep & 50mm wide, up to 2000mm length to form a curvilinear pattern as per the design intent. Polylam shall be manufactured from minimum 1.00mm thickness Galvanized Mild Steel installed at 200mm centres with precision. Finish of the baffle shall be in powder coated to woodgrain finish having minimum 60 microns paint thickness. The carrier rails run perpendicular to the baffles. Individual baffle lengths between 300 and 2000 mm can be selected. Polylam Baffle ceiling are supplied with the end cap matching the similar finish of baffle. Tolerances according to TAIM, DIN EN 13964 and quality controlled to ISO 9001:2008 approved by TUV. Substructure for Vertical baffle system consisting of U shaped galvanized slotted carriers 1.5mm Thick installed perpendicularly to U profiles at maximum 1200mm centres using cross connectors. The primary profiles must be connected to one another with longitudinal splice connectors. The entire ceiling module shall be suspended with 6mm diameter galvanized steel threaded |
| 461 | rods from the true ceiling officially approved anchor fasteners maximum at 1200mm Centres as perthe requirements of DIN EN 13964 and the statics of the system. Ensure horizontal and flush alignment during installation. All ceiling shall be TAIM Certified: For LEED certification by Indian Green Building council (IGBC). The system will meet Fire retardant standard of BS 476: Part 6 & Part 7 |
| 462 | Supply and installation of Wooden Veneer Ceiling made of MS Frame in size 40mm*40mm (18guage) on mount with MS plate & fastener with the true ceiling. 12mm ply place on frame in century brand 1mm Veneer Sheet paste with ply in Century brand Melamine matt finish polish perform on veneer surface with the spray gun. |
| 463 | Supply & installation ofMP3 /approved equivalent , fiber board core,Melamine laminated finish, perforated wooden panels with 3mm perforations at 16mm pitch, backlined with blackacoustical fleece, square edge, of size 600x2400x16mm,having density 800Kg /m3, weight 9.6Kgs/m2 which is suspended by using 0.3mm thick and 24mm wide pre coated metal T24 grid system. |
| 464 | The T24 Grid system shall include providing and fixing wall angle(WA24W30) with equal flanges of size 24mm wide, length 3000mm, 0.4mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the MainT24(MT24W36) having flange width 24mm, height 38mm, length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 600mm c/c . Spacer bar with pre notched slots (wall angle with equal flanges of size 24mm wide, length 3000mm, 0.4mm thick) at 600mm centers in staggered pattern are placed above mainT24 to hold system in position.Spots MPconceil edge of size 600x2400x16mm shall be slidedinto the grid. |
| 465 | Technical Parameters • Core - fibreboard • Fire – 1 • Acoustics – NRC upto 0.55 • Climate (OC RH) – 40, 70 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 1 |
| 466 | TRADITIONAL DESIGN STAINED GLASS CEILING |
| 467 | GLASS BACKLITCEILING |
| 468 | Providing and fixing Teakwood false ceiling at in double height including providing and fixing of composite frame work made of 50x50 mm hardwood and 25x50 mm MS hollow tube, with primer coat, at 600 mm centre to centre, including fixing and finishing of solid teakwood to ceiling framework.The teakwood ceiling to have designer mouldings and motifs, created through CNC router and lathe machine and also including the cost of making openings for light fittings, grills, diffusers, cutouts , all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of treatment and polishing. Solid Teak Wood Ceiling with approved moulding and carving. |
| 469 | 12 mm cement plaster of mix : |
| 470 | 1:4 (1 cement: 4 fine sand) |
| 471 | 6mm cement plaster |
| 472 | 1:3 (1cement: 3 fine sand) |
| 473 | 20mm cement plaster |
| 474 | 1:3 (1cement: 3 coarse sand) |
| 475 | 15mm cement plaster |
| 476 | 1:4 (1cement: 4 fine sand) |
| 477 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 478 | Upto 13m Height |
| 479 | 13m to 16m Height |
| 480 | 16m to 19m Height |
| 481 | 19m to 22m Height |
| 482 | 22m to 25m Height |
| 483 | Providing & fixing Chicken wire mesh on joints of RCC & Brick work before plastering complete |
| 484 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer. Quote for each layer over the plastered wall surface to prepare the surface even and smooth complete. |
| 485 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 486 | Finishing walls withinterior texture paint of required shade : |
| 487 | New work (Two or more coats applied) over and including priming coat of interior grade primer. |
| 488 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. |
| 489 | New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 490 | Painting with oil type wood preservative of approved brand and manufacture : |
| 491 | New work (two or more coats) |
| 492 | Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant. |
| 493 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: |
| 494 | 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. |
| 495 | 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 496 | Polishing with (PU Polish) Polyurethane polish in high gloss/matt finish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:First The surface to be rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with 1st coat of polyurethane polish to fill all the holes/grooves etc. 1st coat to be allowed 2 to 3 days curing period after that The final coat of PU polish is applied with compressor pressure spray gun using clear glossy/Matt finish PU polish in required proportion complete as per direction of Engineer-in-Charge. |
| 497 | Painting with aluminium paint of approved brand and manufacture to give an even shade . |
| 498 | Supply & Installation of Fiberboard core plain, unperforated panels, veneer laminated finish, tongue-groove edge 1200x600x12mm thk -Wall Paneling- Supply and Installation of Fiberboard core plain, unperforated panels, veneer laminated finish, square edge, FR Grade of size 1200x600x12mm having density 750Kgs/ m3, weight 12 kg/m2 installed by using GI framework and Z-bars. |
| 499 | The GI strut work includes Cross channel having thickness 0.45mm, length 3600mm, knurled web 40, depth 10mm and equal flanges 15mm is fastened to wall positioned vertically at 600mm centers. GIZ bars having40mm height, thickness 1.2mm is first fixed behind the panels by using suitable fasteners @ 500mm c/c.Another length of GI Z-Bars are then installed over Strut cross channel horizontally so as to match spacing with Z-bars installed behind panels Panels are then slided into the Z bars fixed on cross channel. Long edged of panels should be perpendicular to Z-bars. |
| 500 | Technical Parameters • Core - Fiberboard • Fire – Class 1 & P • Acoustics – NRC 0.25 • Climate (OC RH) – 50, 70 • Termite resistance – Yes • Light reflectance – Colour dependent • Green (RC %) – 25 • Hygiene (VoC, Clean room) – Low, Class 3 • Strength, Load capacity (Kg) - Antisag |
| 501 | Supplying & Installing Wall paneling:-pinewood HDF core, Veneer laminated finish, groove perforated panels 128x2440x16mm - Supply & installation of Planks made of pinewood HDF core , Veneer laminated finish, groove perforated panels L16-2 - (2mm Slats @16mm pitch), L64-2 - (2mm grooves @ 64mm centers), backlined with black acoustical fleece 0.27mm thk and 63g/m2 surface density, tongue-groove edge for a seamless look, 5-test fire retardant grade, size 128x2440x16mm, volume density of base board 700Kg/m3, weight 9Kgs/m2 (L16), installed by using aluminum Strut framework system. |
| 502 | Strut framework system includes Strut aluminium core cross channel having thickness 0.55mm, length 3600mm, knurled web 40mm, depth 10mm and equal flanges 15mm is fastened to wallor framework behind vertically/horizontally at every 600mm c/c. Strut aluminium core cross channel, thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge ¢re brackets is then fixed perpendicular to the Strut Cross channel with the help of fasteners at every 400mm centers. Panels of size 128x 2440x16mm in then fixed perpendicular to cross channel 18 with suitable edge & centre brackets. Short edges of the panel are staggered. Panels are backlined with acoustic polyfibre 0f 1000GSM surface density and 25mm thk, held in position with dab spots of rubber based adhesive. Contractor to provide expansion joints of 3mm at every 4.88m length wise and 4.992m width wise. |
| 503 | Technical Parameters • Core- PinewoodHDF • Fire – Class 1 & P • Acoustics – NRC 0.75(for L32 varient on C40 mounting) • Climate (OC RH) – 50, 70 • Light reflectance – 75%(Maple arch) • Green (RC %) – 25 • Hygiene (VoC, Clean room) – E1, Class 1 • Strength, Load capacity (Kg) - Ball-Impact |
| 504 | Providing and fixing wall cladding panels with 6mm solid, non-thermo formable, non-porous and homogeneous seamless, stain resistant, repairable, durable, hygienic environment friendly surfacing material acrylic solid surface sheet of or approved make by architect with a minimum thickness 06 mm incolor, design, fixing in customize design arrangement as per direction of Engineer-in- Charge. Acrylic solid surface sheet to be fixed on wall on top of 12 mm marine ply. Adhesive of the same color to provide inconspicuous joints. Grooves to be given at every 1mtr to give expansion & contraction movement to material. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge. Cost of base like framework and 12mm thick ply will be paid under respective item. |
| 505 | Supply & Installation of Cushion wall paneling with premium quality of fabric with fibre cotton over BWP plywood. Fabric, design & pattren approved by Engineer-in-Incharge. Cost of frame and plywood paid in respective item. |
| 506 | Providing and fixing of 4 mm thick annealed SGG Planilaque Evolution (premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client, fixed with SGG Ultrafix or equivalent (compatible neutral core silicon / double sided tape)on a perfectly leveled 12mm thick water proof marine plywood with bevellingand polishing which is mounted on the RCC wall/any other structure ,base structure to be provided by client including ply. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a support wall), coated with PU lacquer (60 micron thick); color consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass; |
| 507 | Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confirming to IS:14587. |
| 508 | Providing and fixing of Wooden Wall panelling made of 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 finished fixed over the MS frame with 40 x 25 x 2.0 hollow sectionat the spacing of600mm c/c. The wall panelling shall be finished with one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with Decorative veneer facings of approved manufacture and shall be finished with melamine polish of approved shade etc complete. |
| 509 | Providing and fixing of 6mm thick mirrorof superior glass (of approved quality) with beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 510 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 511 | Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade, jali slab without any chamfers etc. White sand stone. |
| 512 | Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge. |
| 513 | Supply and fixing of prefabricated GI trap 600 mm x 600 mm doors of to be recessed in ceilings wherever required. |
| 514 | Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 900x600x2100 Recessed type mansoary box (by civil contractor). |
| 515 | Providing and fixing of TAC approved 1.6mm thickM.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant. |
| 516 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal |
| 517 | Single headed Gunmetal |
| 518 | Supplying and fixing first-aid Hose Reel with MS Construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20mm nominal internal dia water hose thermoplastic (textile reinforced) type- 2 as per IS: 12585 20 mm nominal internal dia gun netal globe value & nozzie.Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. - 30m length |
| 519 | 30 m |
| 520 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal |
| 521 | Gun Metal |
| 522 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun Metal |
| 523 | Gun Metal |
| 524 | Providing and fixing of Fire Axe |
| 525 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. |
| 526 | Providing and fixing C.I.double acting air valves of approved quality with bolts, nuts, rubber insertions etc. complete ( The tail pieces, tapers etc. if reqd. will be paid separately) |
| 527 | 50 mm dia. |
| 528 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : |
| 529 | 150 mm dia |
| 530 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : |
| 531 | 80 mm dia |
| 532 | 100 mm dia |
| 533 | 150 mm dia |
| 534 | Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required |
| 535 | Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). |
| 536 | 25mm dia |
| 537 | Providing, laying, testing & commissioning of "C" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 538 | 150 mm nominal bore (class C) |
| 539 | 100 mm nominal bore (class C) |
| 540 | 80 mm nominal bore (class C) |
| 541 | 65 mm nominal bore (class C) |
| 542 | 50 mm nominal bore (class C) |
| 543 | 40 mm nominal bore (class C) |
| 544 | 32 mm nominal bore (class C) |
| 545 | 25 mm nominal bore (class C) |
| 546 | Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. |
| 547 | 150mm dia |
| 548 | 100mm dia |
| 549 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. |
| 550 | Providing, fixing, testing & commissioning of 15mm dia uartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : |
| 551 | Horizontal side wall sprinkler |
| 552 | Pendent /Uprighttype |
| 553 | Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. |
| 554 | 1200mm |
| 555 | Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required. |
| 556 | Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming toIS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. |
| 557 | Capacity 4.5 kg |
| 558 | Providing and fixing (ABC Dry Chemical Powder ) type Fire Extinguisher of Capacity 6 kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket complete with internal charges. |
| 559 | Capacity 6 Kg. |
| 560 | Boring: - Boring/drilling 300mm dia hole in to all kinds of the soils by Suitable Drilling Rig / DMC method to the design depth below the Existing Ground level in accordance with Consultant"s drawings including setting out cardinal points, Boring in over burden through all strata"s up to design depth, including chiselling through obstacles like boulders, weathered rock. removal of temporary casing if any, etc complete. |
| 561 | Piling Works : - Providing and placing 168 mm dia MS Pipe of 6 to 7.1 mm thick after necessary fabrication with necessary Compressor, Equipment, Collars, Washer Plates, Welding, Material, labour, tools and tackles etc., complete. , as per directions of the Engineer in charge of the work |
| 562 | Grouting:- Providing andGrouting the annular spaces between the M S Pipe and Drilled Hole with Cement slurry with water cement ratio of 0.45 with non-shrink admixture, under a pressure of 1.5 to 2 bar, including necessary Material, labour, equipment"s etc. complete as per directions of the Engineer in charge of the work. |
| 563 | Providing& Placing cement concrete of M20 grade using river sand, 20mm and down size coarse aggregates with minimum cement content of 300 kg/cum and placing into the bore by tremie method.The rate shall include cost of approved ordinary Portland cement of specifiedgrade, necessary admixtures as approved by consultant . Design mix to be approved by the consultants, Water cement ratio to be within 0.5, the slump at pouring point to be maintained 140mm+/-10mm. The age of concrete while pouring should not exceed 2Hrs. |
| 564 | Shotcrete: Thickness 50 mm:- Providing shotcrete using M30 grade of concrete with 1:2:1 ratio od Cemant,Sand and aggregate with OPC 43 or 53 grade cement, sand and 6mm downsize aggregateas per IS 9012-1978 including providing & fastening of welded wire mesh of size 50 x 50x 2.8 mmincluding necessary U hooks, as per scheme Curing, wastage etc,. complete. |
| 565 | Weep Holes:- Providing and placing weep holes having 3 m long, 75 mm dia perforated PVC Pipe with pores covering about 6 to 8% of the surface area wrapped with one layer go Geo Textile with end cap. including all material, labour, tools and tackles, The weep hole are inserted in a pre drilled hole of 100 mm with an inclination of 10o upwards direction etc,. complete. |
| 566 | Grouted Anchors:- Providing installing25mm Dia TMT on the soil surface with a H S = 2.0 mtr, V S = 2.0 mtr up to the required depth ( Excluding cost of TMT Steel) in all kind of strata using driving equipment including cost of all materials, labour, machines hire, scaffolding, curing Etc. complete asper the direction of Engineer in charge of work. |
| 567 | Providing, drilling, fabricating, driving, fixing of Grouted Nails for anchoring of Micro Piles using specified di aTMT or Reinforced Bars as per spacing specified in the drawings up to the required depth using suitable drilling equipment and Compressor. Rate shall include drilling of holes, spacers, etc complete including grouting. with Cement slurry with water cement ratio of 0.45 with non-shrink admixture, under a pressure of 1.5 to 2 bar, including necessary Material, labour, equipment"s etc. complete as per directions of the Engineer in charge of the work - With 150 diameter Drilling of bore holes in all types of Soil and Rock, as per specification. (Rate including Steel Stands required qty) |
| 568 | Grouting using Cement Grout with non-shrink compound and having water cement ratio of 0.45 -150 diameter for Grouted Anchors |
| 569 | Supplying, fabricating and erecting Structural steel members as specified in the drawings made out of built up/standard MS sections conforming to IS 226/2062/800. The structural steel work shall include welded and built up sections, Cost to include welding of members using structural steel welding electrodes as per IS 814/816/817,Coats of anti corrosive primer (non flammable) to the exposed surfaces, testing asper IS 7307 (PART 1), necessary plants, equipment"s, tools and tackles, staging, scaffolding required etc., complete, |
| 570 | The rate to include aligning, levelling, providing and fixing bolts, nuts, washers, comprising MS angles, channels, joists, rails, tees, plates, chequered plates, flats, rounds, squares etc., of various sizes and other structural steel sectionsconforming to latest IS 2062 Grade - A & B including straightening, cutting, welding, bending to shape, bolting, transportation, errection,shop drawings preparation, fabrication drawings/ OE & PMCs approval. The rate to include the cost of all materials, labour, tools, tackles, cranes, devices and plants, wastage, shims and packing pieces etc., as per specification and drawings complete. Wailer Beam, angles, plates, etc.; Grade: 350 |
| 571 | Supply and insallation of dewatering pumps and piping arragements of required capacity to dewater the total area of around 2400 sqm upto the total delivery / suction head of 20 meter and the period upto 8 months as per the direction of Engineer-in-charge |
| 572 | 11KV SINGLEPANEL HT VCB (INDOOR)-STANDALONE- INCOMER CUM OIUTGOINGIN IP-4X ENCLOSURE Design, Manufacture and Supply of Incoming cum out goingpanel, 11 kV HT VCB Switch Board with Following Accessories: Incoming 800A, 11kV, 350MVA for 3 Sec., TP, Horizontally isolated, horizontally drawout type, motorised spring charged, closing mechanism, motor voltage 230V AC, shunt tripping & Closing coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum Circuit Breaker(VCB) With Mechanical & Electrical OFF/ON Indicators & Provided with Following -1 No. CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of 110_/5/5A ratio - 3Nos. |
| 573 | IDMT relay with 3 elements for over current (50-200%) and 1 element for earth fault protection(10-40%). - 1 Set Anti Pumping Relay - 1 Set Master Trip Relay - 1 Set Trip circuit supervision relay - 1 Set Potential transformers, 3 phase, 3 limb,drawout type, resin cast 11000/(Root 3)/110/(Root 3) ratio class 1accuracy, 100 VA burden, with HV fuse on primary side and MCB/ MPCB on secondary side. - 1 Set |
| 574 | 6 Windows Annunciator with Hooter - 1 Set 1 Window for over current trip - 1 Set 1 Window for earth fault trip - 1 Set 1 Window for master trip relay - 1 Set 1 Window for Emergency Stop Push Button - 1 Set 2 Windows Spare - 1 Set Digital Ammeter with inbuilt selector switch - 1 Set Digital Voltmeter with inbuilt selector switch - 1 Set A set of breaker ON/OFF/Trip/DC control supply healthy/Trip circuit healthy/ Spring Charged VCB in test / VCB in service & R,Y,B phase indication lamps. - 1 Set |
| 575 | Emergency stop push button -1 Set Limit switches with 4 NO/ 4 NC breaker auxiliary contacts - 1 Set Control:- T-N-C (Trip, Neutral, Close) breaker control switch with indication arrangement. - 1 Set All control wiring with protection & test terminal block as required. - 1 Set Strip heater with thermostat for moisture absorption. - 1 Set Suitable for connection to 3C x 240 sq.mm. Cross linked polythelene(XLPE) 11kV cables or as called for. - 1 Set Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set HT Danger Plate - 1 Set Incoming as described above. 1 Sets Bus Bars: 800A TP 11KV AL. Busbars With Heat Shrinkable Insulation Sleeves Powerpack as Required to Be Included (220V/24V DC), 7AH Battery for Each Breaker Module. |
| 576 | SINGEL BREAKER INCOMING CUM OUTGOING PANEL |
| 577 | 11KV THREE PANEL HT VCB (INDOOR)-ONE INCOMERS, & TWO OUTGOINGS IN IP-4X ENCLOSURE |
| 578 | Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, 11KV VCB panel with 3 No. VCBs, totally enclosed & fully interlocked, horizontal drawout, horizontal/ vertical isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and auto/manually closing breaker suitable for use on 11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVa, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 630 Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 4 NO+4NC and equipped with following switchgears and accessories i/c connections suitable for 3x240 sq. mm. XLPE 11KV cable (cable entry from *bottom/ top/side) end termination with heat shrinkable jointing material etc. as required. The Panel Shall consisting of following:- |
| 579 | Incoming 800A, 11kV, 350MVA for 3 Sec., TP, Horizontally isolated, horizontally drawout type, motorised spring charged, closing mechanism, motor voltage 230V AC, shunt tripping & Closing coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum Circuit Breaker(VCB) With Mechanical & Electrical OFF/ON Indicators & Provided with Following -1 No. |
| 580 | CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of 110_/5/5A ratio - 3Nos. IDMT relay with 3 elements for over current (50-200%) and 1 element for earth fault protection(10-40%). - 1 Set Anti Pumping Relay - 1 Set Master Trip Relay - 1 Set Trip circuit supervision relay - 1 Set Potential transformers, 3 phase, 3 limb,drawout type, resin cast 11000/(Root 3)/110/(Root 3) ratio class 1accuracy, 100 VA burden, with HV fuse on primary side and MCB/ MPCB on secondary side. - 1 Set 6 Windows Annunciator with Hooter - 1 Set 1 Window for over current trip - 1 Set 1 Window for earth fault trip - 1 Set 1 Window for master trip relay - 1 Set 1 Window for Emergency Stop Push Button - 1 Set 2 Windows Spare - 1 Set Digital Ammeter with inbuilt selector switch - 1 Set Digital Voltmeter with inbuilt selector switch - 1 Set A set of breaker ON/OFF/Trip/DC control supply healthy/Trip circuit healthy/ Spring Charged VCB in test / VCB in service & R,Y,B phase indication lamps. - 1 Set |
| 581 | Emergency stop push button -1 Set Limit switches with 4 NO/ 4 NC breaker auxiliary contacts - 1 Set Control:- T-N-C (Trip, Neutral, Close) breaker control switch with indication arrangement. - 1 Set All control wiring with protection & test terminal block as required. - 1 Set Strip heater with thermostat for moisture absorption. - 1 Set Suitable for connection to 3C x 240 sq.mm. Cross linked polythelene(XLPE) 11kV cables or as called for. - 1 Set Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set HT Danger Plate - 1 Set Incoming as described above. 1 Sets Bus Bars: 800A TP 11KV Cu. Busbars With Heat Shrinkable Insulation Sleeves |
| 582 | Outgoings 2 Nos.:630A, 11kV, 350MVA for 3 Sec., TP, Horizontally Isolated, Horizontally Drawout Type, Motorised Spring Charged, Closing Mechanism, Motor Voltage 230V AC, Shunt Tripping & Closing Coil Voltage 24V DC, Electrically Operated, Trip Free, Dust & Vermin Proof, Vacuum circuit breaker(VCB) with mechanical & Electrical OFF/ON indicators & provided with following - 1 No. CT chamber with double wound single phase, cast resin CT, 15VA burden with core-1 for metering (CL-1) and core-2 for protection (CL-5P10) and of100_/5/5A ratio. - 3Nos. Digital Ammeter with inbuilt selector switch - 1 Set IDMT Relay with 3 Elements for Over Current (50-200%) and 1 Element for Earth Fault Protection(10-40%) With High Set. 1 Set Anti Pumping Relay - 1 Set Master Trip Relay - 1 Set Trip circuit supervision relay - 1 Set A Set of Breaker ON/OFF/Trip/DC Control Supply Healthy /Trip Circuit Healthy/ Spring Charged VCB in Test / VCB in Service.1 Set |
| 583 | Auxiliary Relays for Transformer Faults WTI, OTI and Bucholz Relay.(To be Checked With the Requirement of Transformer i.e. For ONAN or Dry Type) For Alarm & Trip. 1 Set 12 windows annunciator with hooter: 1 window for over current trip 1 window for earth fault trip 1 window for winding temperature alarm 1 window for winding temperature trip 1 window for Oil temperature alarm 1 window for Oil temperature trip 1 window for Buchloz alarm 1 window for Buchloz trip 1 window for master trip relay 1 window for emergency stop push button 2 windows spare Emergency Stop Push Button - 1 Set Limit Switches With 4 NO/ 4 NC Breaker Auxiliary Contacts - 1 Set |
| 584 | Control:- T-N-C (Trip, Neutral, Close) Breaker Control Switch With Indication Arrangement. - 1 Set All control wiring with protection & test terminal block as required. - 1 Set Strip heater with thermostat for moisture absorption. - 1 Set Cable box for 3C x 240 sq.mm 11kV XLPE Al. conductor cable. - 1 Set HT Danger Plate - 1 Set Powerpack as Required to Be Included (220V/24V DC), 7AH Battery for Each Breaker Module. THREE PANEL 11KV HT VCB PANEL AS DESCRIBED ABOVE |
| 585 | 11KV TRANSFORMER(11 KV /433 V) (2000 KVA) - 1WORKING + 1 STAND BY |
| 586 | Supply, Installation, Testing and Commissioning ofDRYTYPE DISTRIBUTION (CRT)11KV / 433 Volt Rating 3 phase, Double Wound with copper Winding.(As Per IS : 11171 -1985 & IS : 2026), losses as per latest ECBC norms,Tapping Range in Steps (+5% to -10% @ 1.25%) on load tap changer, Insulation class : class F , Temperature rise by Resistance : 90 deg.c , Ambient Temperature 50 deg.c, Dyn 11 vector group and Other Standard Accessories as Required Including Followings : 1. Rating & Diagram Plate - One 2. Earthing Terminals - Two 3. Lifting Lugs - Four 4. RTCC - One 5. AVR - One 6. Separate Neutral Bushing - One 7. HV Cable Box - One 8. LV Cable Box - One 9. Winding Temperature Indicator (Scanner Type) - One 10. Bi - Directional Rollers - Four 11. Marshalling Box - One 12. M.S Enclousure - One 13. Surge Arrestors |
| 587 | 2000 KVA (11/433V) AS DESCRIBE ABOVE |
| 588 | Providing, Installing,TestingandCommissioningof"StandardType"DieselGeneratingsetalongwith having PrimePower Rating of625 KVA, 415 volts at1500 RPM,0.8 lagging power factorat 415V suitable for 50 Hz, 3 phase system and consisting of the followings: (Total of a to h). |
| 589 | Diesel Engine: Diesel engine 4 stroke water cooled, heat exchanger type electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL and conforming toBS5514,BS649,IS10000,capableoftaking10%overloadingforonehourafter12hoursof continuous operation. The engine will be fitted complete with all required accessories. |
| 590 | Engine mounted Instrument Panel fitted with and having digital display for following: |
| 591 | Start-stop switch with key. |
| 592 | Water temperature indication. |
| 593 | Lubrication oil pressure indication. |
| 594 | Lubrication oil temperature indication. |
| 595 | Battery charging indication. |
| 596 | RPM indication. |
| 597 | Over speed indication. |
| 598 | Low lub. Oil trip indication. |
| 599 | Engine Hours indication. |
| 600 | Alternator: Electronic alternator rated at 625KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC Supply with 0.8 lagging power factor at 40 Degree C, 50% RH & AT 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self - regulated through AVR conforming to IS: 4722/BS 2613 Suitable for tropical conditions and with class - H insulation. |
| 601 | Base Frame & Foundation: BoththeengineandalternatorshallbemountedonsuitablebaseframemadeofMSchannelwith necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer. |
| 602 | Fuel Tank: |
| 603 | Daily service fuel tank of standard capacity fabricated out of 3 mmthick M.S. Sheet complete with all standard accessoriesand fuelpiping between fueltankand diesel engine with MS class "C"pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications. |
| 604 | Exhaust System: Dry exhaust mainfold with hospital exhaust silencer. |
| 605 | Starting System: 24VDCstartingsystemcomprisingofstartermotors:voltageregulatorandarrangementforinitial excitation complete with2 nos. of batteries (180 Amp. Hour capacity lead acid type) as required as per specifications. |
| 606 | Accoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere as per specifications. |
| 607 | Supply, installation, testing and commissioning of 990 litres capacity Day Oil tankfabricated from 2 mm thick MS sheets including the cost of providing removable cover flush with floor and including the cost of provisions for inlet and outlet connections, foot valve, Dial type mechanical oil level indicator on the top, located nearere to the DG and set withprovision for refillng byuse of semi rotary pump. |
| 608 | Supply, erection Testing and commissioning of a semi rotary hand pump for filling fuel in daily Fuel Tank including the cost of suitable fuel piping and connections complete as required. |
| 609 | Supply, installation testing and commissioning of fuel oil piping system fabricated from Class B following size MS pipes cut to required lengths and installed with all welded joints including providing and fixing in position the necessary fittings like elbows, tees, reducers, duly coated with one coat of primer and two coasts of approved enamel paint complete as per specifications and as required |
| 610 | 20dia |
| 611 | Supply, installation testing and commissioning of following oil piping accessories complete as required |
| 612 | 20NB ball valve |
| 613 | Supplying & fixing exhaust gas piping of suitable dia. Welded black MS, B class pipe confirming to IS:3589 cut to required lengthsand installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with mineral wool/rockwool, 50mm thick wiremesh & aluminium clading etc, as required as per specification. |
| 614 | 250 mm dia |
| 615 | Providing and fixing in position following size of heavy duty stainlesssteelflanged expansion bellows with G.I. nut bolt washers for DG fume pipingcomplete with GI nut bolt washers etc. complete asrequired. (for DG Sets) |
| 616 | 250 mm dia |
| 617 | Providing & fixing for MS support structure for exhaust fume pipes from DG Sets (Exhaust pipe to be measured and paid for separately) along horizontal and vertical runs upto the height (as per CPCB norms) including cutting, welding etc. and applying two coats of red oxide and two coats of synthetic enamelled paint of colour and shade as directed by engineer-in-charge. The design of the support structure shall be done by the contractor and shall be as per CPCB norms approved , also to get the approval from the client/ consultant before execution etc. as required. |
| 618 | DG COOLING SYSTEM Supply, installation, testing and commissioning of FRP type Cooling Towers (induced draft) of nominal capacity as below induced sump, hot dip galvanized steel ladder, TEFC Squirrel cage induction motor PVC fillings with louvers and drift eliminators, AXIAL flow fan, make up, quick fill, over flow, drain arrangement concrete foundations, MS supporting channels, angels etc. suitable for outdoor installation etc. complete as per specifications and as required. The tower supporting structure shall be made out of stainless steel (grade 304) with SS fitting & accessories. |
| 619 | 60 TR (625 KVA Gen Set) |
| 620 | Supply, installation, testing and commissioning of monoblock centrifugal Pump sets factory assembled with stainless steel/bronze Impeller, Mechanical seal and tested for rated efficiency complete with TEFC motor and common base frame for circulation of water as below against head of 80 meters for the DG set cooling system suitably required for DG set. The pump sets shall besuitable foroperationon 415 +10% volts, 50 Hz, 3-phase powersupply with 100 mm dia pressure gauge, ball valves and piping as per specification as required. |
| 621 | 540 LPM, Head 80 Mtr (For 625KVA Genset Set)(1W+1S/B) |
| 622 | The Pipes of sizes 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of |
| 623 | 80 mm dia |
| 624 | 80 mm dia Butterfly valves(PN-10/PN-16) |
| 625 | 80 mm dia Non return valves(PN-16) |
| 626 | 80 mm dia Y strainers(Test Pressure - 20 Kg/cm2g) |
| 627 | 80 mm dia POT strainers |
| 628 | Flexible coupling(80mm) |
| 629 | Pressure Gauge |
| 630 | Tempreatre Gauge |
| 631 | 80 mm dia Butterfly valves normally closed(PN-10/PN-16) |
| 632 | 80 mm dia Gate valve(Hex. Type). |
| 633 | NOTE:- MCCB"s wherever specified shall have rotary handle. Supply, installation, testing & commissioning of cubical type LT panel suitable for 415V, 3 phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized (preferably) design from CRCA sheet steel of 2 mm thick for frame work & covers, 3mm thick for gland, plates i/c cleaning & finishing complete with 7 tank process for power coating in approved shade, having 4000 Amp capacity extensible type TPN aluminium alloy busbar of high conductivity, DMC/SMC bus bar of high conductivity, DMC/SMC bus bar supports, with short circuit withstand capacity of 36kA for 1 second, bottom base channel of MS secton not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have common copper earth bar of size 25 mm x 5 mm at the rear with 2 nos. earth stud, solid connections from main busbar to switch gears with required size of Al. bus bars and control wiring with 2.5sqmm PVC insulated copper conductor S/C cable, cable alleys, cable gland plates in two half, i/c providing following switch gears. |
| 634 | The outgoing feeders as indicated in SLD shall have suitable range of followings (except capacitor feeders). All ACB"s shall be suitable for minimum 50 kA as specified in the items (Icu=Ics=Icw for 1 sec.) All MCCB"s shall be suitable for unless otherwise specified in the item (Icu=Ics= 1 sec=100%.) Wiringwith space heater, thermostat and control MCB"sshall be provided for all vertical sections of main LT panel. All incoming as well as outgoing feeders shall have pad locking facility. Suitable danger board shall be provided. All MCCB’s shall be provided with front rotary handle and operating mechanism for door interlock with Pad locking of MCCB’s handles in “OFF” Position. The Panel fabricator shall provide Al./ Copper Bus-bars link from Breakers wherever more than two nos. of cables are terminated in the breakers. |
| 635 | All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single tier formation. All distribution sub panels shall be provided with class 1.0 accuracy meters as well as CTs. All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire. Panels shall be Powder Coated with Siemens grey paint shade no. RAL-7032 of IS-5. All motor feeders MCCBs shall be of motor duty. Supporting/Base rigid steelframework. 4P ACB’s / MCCB’sshall mean 4 pole ACB’s / MCCB’swith adequate size of neutral link. All MCCB above 250A shall be microprocessor base. |
| 636 | INCOMER FROM GEN SET (625 KVA) 4NOS. 4 Nos. of 1000 A, 4P electrically operated Drawout type ACB with Ics=Ics=50KA having Mircroprocessor based releases for O/L, S/C & E/F protection. 4 Nos. SPD Type 1 4 Sets - digital multifunction meter (showing harmonics along with all other electrical parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT"s 4 Sets - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED lamp to show the incoming power with control SP MCB. 4 Sets indicating LED lamps for ACB On/Off/ Trip with protective SP MCB"s. 4 Sets of CTs of the ratio 1000/5A with Class 1 Accuracy for Metering, burden 15 VA 4 Nos. 1000/5A , 15 VA, Class-5P10 CT"s for Protection 4 No. Under Voltage relay 4 Nos. over Voltage relay 4 Nos. Over & under frequency relay |
| 637 | INCOMER From 2 nos. 2000 KVA TRANSFORMER 2 Nos. of 3200 A, 4P electrically operated Drawout type ACB with Ics=Ics=50KA having Mircroprocessor based releases for O/L, S/C & E/F protection. 2 Nos. SPD Type 1 2 Sets - digital multifunction meter (showing harmonics along with all other electrical parameters such as voltage, current, Hz, KW, KWHr, PF.) with RS 485 port with matching cast resin CT"s 2 Sets - 0-500V, digital Voltmeter with selector switch, 3 No. phase indicating LED lamp to show the incoming power with control SP MCB. 2 Sets indicating LED lamps for ACB On/Off/ Trip with protective SP MCB"s. 2 Sets of CTs of the ratio 3200/5A, Class-1 for APFC Relay, Burden 15 VA 2 Sets of CTs of the ratio 3200/5A with Class 1 Accuracy for Metering, burden 15 VA 2 Nos. 3200/5A , 15 VA, Class-5P10 CT"s for Protection 2 No. Under Voltage relay 2 Nos. Negative Phase protection Relay 2 Nos. over Voltage relay 2 Nos. Over Current Relay & earth fault relay 2 Nos. Over & under frequency relay |
| 638 | BUS BARS TPN aluminium bus bars of minimum of 4000 Ampscapacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bar cross section, size supports & their spacing etc. for withstanding faultcurrent of 50kA for 1 sec. |
| 639 | BUS COUPLER:- 1 No. of 3200 A, 4P electrically operated Drawout type ACB with Ics=Ics=50KA having Mircroprocessor based releases for O/L, S/C & E/F protection. 1 Set of Breaker ON-OFF indication Lamps as required. Interlocking: Electrical through advance contacts in MCCB/ACB"s (Incomer & bus couplers) & mechanical (castel key) interlocking should be provided to ensure that only one supply is available at a time on each section of bus & to eliminate any possibility of accidentlly approaching two supplies at one bus section. |
| 640 | OUTGOINGS-Bus Section-1 |
| 641 | 1 No. 1250A TP ACB (50 KA) |
| 642 | 2 No. 630A 4P MCCB (50KA) |
| 643 | 1 No. 630A 4P ATS (The ATS shall be complying to Standard IEC 60947-6-1 & 60947-3 with Third Party Test Certificate .The ATS should have four poles with fully rated neutral & controller with separate watchdog relay for both controller and motor.) |
| 644 | 2 No. 500A 4P MCCB (50KA) |
| 645 | 5 No. 200A 4P MCCB (36 KA) |
| 646 | 1 No. 160A 4P MCCB (36 KA) |
| 647 | 2 No. 100A 4P MCCB (36 KA) |
| 648 | 1 No. 80A 4P MCCB (36 KA) |
| 649 | OUTGOINGS-Bus Section-2 |
| 650 | 1 No. 1250A TP ACB (50 KA) |
| 651 | 2 No. 500A 4P MCCB (50KA) |
| 652 | 1 No. 250A 4P MCCB 36KA) |
| 653 | 6 No. 63A 4P MCCB (36 KA) |
| 654 | 3 No. 200A 4P MCCB (36 KA) |
| 655 | 1 No. 200A 4P ATS (The ATS shall be complying to Standard IEC 60947-6-1 & 60947-3 with Third Party Test Certificate .The ATS should have four poles with fully rated neutral & controller with separate watchdog relay for both controller and motor.) |
| 656 | 3 No. 160A 4P MCCB (36 KA) |
| 657 | 2 No. 125A 4P MCCB (36 KA) |
| 658 | 2 No. 80A 4P MCCB (36 KA) |
| 659 | 2 No. 32A 4P MCCB (36 KA) |
| 660 | PLC FEEDER- FOR AMF FOR AUTO ON/OFF THE DG, LOAD MANAGEMENT & E/M INTERLOCKING: Hardware using PLCs for Monitoring of all Electrical Software and for operations, controlling andinterlocking Parameters of2 Nos. I/C from Transformer & 4 Nos. Gen Set with Window based software & Engineering & Software Development. Required Aux. Relays, Push Buttons & Indication lamps, 1KVA UPS for Black start & maintenance free Batteries, Power monitors, Programmable Logic controller, Annunciator and status Fascia, MIMIC with LED circuit etc as required completing the system. The Switchboard with Logic control panel shall be complete with all interconnections, risers, internal wiring, labels, control/circuit fuses etc. complete as required. Note: Incomer from LT Supply, Gen set & Bus coupler shall be electrically& mechanically interlocked. |
| 661 | Main LT Panel as described above |
| 662 | Note: The outgoing feeders as indicated in SLD shall have suitable range of followings (except capacitor feeders) Three phase indicating lamps protected by 2 amps SP MCBs. |
| 663 | All ACB"s shall be suitable for minimum 25 kA ( Icu=Ics=Icw for 1 sec.) |
| 664 | 415/110V suitable rating control transformer and shall be provided for aux. control supply. |
| 665 | Wiring with space heater, thermostat and control MCB"sshall be provided for all vertical sections of main LT panel. |
| 666 | All breakers shall be interlocked as per schematic diagram through Mini PLC. |
| 667 | All incoming as well as outgoing feeders shall have pad locking facility. |
| 668 | Suitable danger board shall be provided. |
| 669 | Incase of Fire, Fire pumps along with other ventilations and pressurization fans designed shall become operational. Interlocking with LT panel shall be carried out accordingly. |
| 670 | AUTOMATICPOWERFACTORCORRECTIONPANEL(CAPACITOR PANEL) - 700 KVAR |
| 671 | Supplying, installation, testing and commissioning of cubicle type capacitior panel suitable for 415 & 3 phase 50 HZ A.C. supply System fabricated in compartmentalised design from CRCA Sheet Steel of2 mm thick for frame work and cover, 3 mm thick for gland plates i/cpowder coating in approve shade having 1250 AMP capacityTPN Aluminium bus bar DMC/SMC bus bar supprot entire pannel should have common Al. earth bar for size 50 mm x 5 mm i/c Providing & fixing following switch gear mounting there on fans,grills for propor ventillation complete with gaskets & inner connection i/c connection with existing CTS in the main CT Panel complete as reqd. The panel board shall be of dust and verm proof with degree of protection IP 42) |
| 672 | a) 1250 Amps TP ACB 50KA with Microprocessor Based release and E/F proctection with time dely(Ics=100% Icu) - 1 No. b) 1250 A, 4 strip Tinned Aluminium busbar -1 Set c) Micro processor based automatic Power factor control relay i/c power factor metre in 10 steps d) Multi functional meters with suitable CTS and protection MCBS 1 set. e) 3 Nos. Phase indieating right (lamp) with MCBs protection. |
| 673 | OUTGOINGS- 5 Sets -250 A TP MCCB 25 KA and capacctor duly switching contactor 100 KVAR capacity auto mannual selector switch start stop push button on/off indicating lamp with protection MCB and belay timer complete to i/c100 KVARmixed dielectric with 7% detuned filler copper reactor type capacitor bank with inter connection 3 Sets -200 A TP MCCB 25 KA and capacctor duly switching contactor 75 KVAR capacity auto mannual selector switch start stop push button on/off indicating lamp with protection MCB and belay timer complete to i/c75 KVARmixed dielectric with 7% detuned filler copper reactor type capacitor bank with inter connection 2 Sets -125 A TP MCCB 25 KA and capacctor duly switching contactor 50 KVAR capacity auto mannual selector switch start stop push button on/off indicating lamp with protection MCB and belay timer complete to i/c 50 KVARmixed dielectric with 7% detuned filler copper reactor type capacitor bank with inter connection |
| 674 | Cap. Panel as described above |
| 675 | MAIN LIFT PANEL IP Rating : IP 42 Incomer 1 No. 200 A 25 KA, 4P MCCB Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio 1 No. Digital VAF + PF Meter (110V)(With RS 485 Port) Bus bars 250A, TPN Aluminium Bus bars of electrolytic grade with heat shrinkable sleeve 25 KA. |
| 676 | Outgoings 1 Nos. 125 10KA, 4P, MCCB"s, (LIFT PANEL GUEST HOUSE ) 1 Nos. 125A 10KA, 4P, MCCB"s, (LIFT PANEL 01 MAIN BLOCK) 1 Nos. 125A 10KA, 4P, MCCB"s, (LIFT PANEL 02 MAIN BLOCK) 1 Nos. 125A 10KA, 4P, MCCB"s, (LIFT PANEL 01 RESIDENCE BLOCK) 1 Nos. 125A 10KA, 4P, MCCB"s, (SPARE) Panel as described above. |
| 677 | EXTERNAL LIGHT PANEL Design,Manufacture, Supply, Installation,Testing and CommissioningofPanelFabricated out of 16 SWG CRCA sheet steel,IP 54, wall / floor mounting type with rain canopyThe sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands,including connection with outgoing feeders completeinall respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid. INCOMER: 1 no. 100 A, 25KA 4P MCCB BUS BAR TPN Aluminium bus bar with heat Shrink Sleeve rated for 125A. |
| 678 | OUTGOING 14 nos 32A DP MCBON indication lamps with 14 nos astronimical time swtich for automaitc switching of landscape light fixtures at sun set and sun rise or twillight ( auto on/ auto off and auto mode)with manual override faiclity with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site. 2 nos 63A 4P MCB (SPARE) 2 nos 40A DP MCB (SPARE) Other items such as 1 Set of control wiring 1 Set of designation plates All Items complete as above |
| 679 | LIFT PANEL IP Rating : IP 42 Incomer 1 No. 125 A 25 KA, 4P MCCB Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio 1 No. Digital VAF + PF Meter (110V)(With RS 485 Port) Bus bars 150A, TPN Aluminium Bus bars of electrolytic grade with heat shrinkable sleeve 25 KA. |
| 680 | Outgoings 1 Nos. 63A 10KA, 4P, MCB"s, (LIFT PANEL 1) 1 Nos. 63A 10KA, 4P, MCB"s, (LIFT PANEL 2) 1 Nos. 63A 10KA, 4P, MCB"s, (LIFT PANEL 3) 1 Nos. 63A 10KA, 4P, MCB"s, (LIFT PANEL 4) 1 Nos. 63A 10KA, 4P, MCB"s, (MACHINE ROOM DB) 1 Nos. 63A 10KA, 4P, MCB"s, (SPARE) Lift Panel as described above. |
| 681 | TYPICAL FLOOR PANEL(GR TO 6TH FLOOR) IP Rating : IP 42 Incomer 1 No. 100A 25 KA, 4P MCCB Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio Incomer shall have suitable surge supressor/ TVSS Bus bars 160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 25 KA. |
| 682 | Outgoings 1 Nos. 40A, 4P MCB"s -(DB 1) 1 Nos. 40A, 4P MCB"s -(DB 2) 1 Nos. 32A, 4P MCB"s -(HVAC AHU PANEL MCC 01) 1 Nos.63A, 4P MCB"s -(HVAC AHU PANEL MCC 02) 2 Nos. 40A, 4P MCB"s -(SPARE) Vendor to ensure selection of MCCB & MCB through cascading effect to mitigate the prospective fault circuit current. Panel as described above. |
| 683 | BASEMENT LIGHTING & POWER PANEL IP Rating : IP 42 Incomer1 No. 100A 25 KA, 4P MCCB (fixed Thermal & fixed Magnetic releases) Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio |
| 684 | Incomer shall have suitable surge supressor/ TVSS Bus bars 160 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 35 KA. Outgoings 12 Nos. 40A, DP MCB"s -(DBs) 1 Nos. 40A, DP MCB"s -(SPARE) 2 Nos. 63A, 4P MCB"s -(SPARE) Vendor to ensure selection of MCCB & MCB through cascading effect to mitigate the prospective fault circuit current. Panel as described above. |
| 685 | MAIN VENTILATION PANEL-1 (3RD BASEMENT) IP Rating : IP 42 Incomer 1 No. 200A 25 KA, 4P MCCB (fixed Thermal & fixed Magnetic releases) Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio |
| 686 | Bus bars 250 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 35 KA. Outgoings 5 Nos. 63A, 4P MCCB"s(25kA) Panel as described above. |
| 687 | MAIN VENTILATION PANEL-2 (2ND BASEMENT) IP Rating : IP 42 Incomer 1 No. 200A 25 KA, 4P MCCB (fixed Thermal & fixed Magnetic releases) Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio |
| 688 | Bus bars 250 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 35 KA. Outgoings 6 Nos. 63A, 4P MCCB"s(25kA) Panel as described above. |
| 689 | MAIN VENTILATION PANEL-3 (1ST BASEMENT) IP Rating : IP 42 Incomer 1 No. 200A 25 KA, 4P MCCB (fixed Thermal & fixed Magnetic releases) Incomer Metering & Indication: 415V / v3 / 110V/ v3PT"s, Cast Resin type, 3 Phase for metering & indications, suitable rated 6A, TP MPCB of the fault withstand capacity as of the panel on the primary side of PT & suitable rated 6A, TP MCB on the secondary side of PT. This metering PT shall be of Class-1 accuracy. R,Y,B phase indication lamps (110V) LED Type ON" & Trip indication lamps (110V) LED Type Cast resin metering CT"s for each phase of class-1 accuracy & of suitable burden & ratio |
| 690 | Bus bars 250 A, 4P, Aluminium Bus bars of Electrolytic grade with heat shrinkable sleeves 35 KA. Outgoings 4 Nos. 63A, 4P MCCB"s(25kA) 1No. 125A, 4P MCCB"s(25kA) Panel as described above. |
| 691 | Supplying, installing by suspension on ceiling/along the wall, testing and commissioning of following capacity BUS DUCT for use on 3 phase 4 wire 415 V, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos. aluminium bus bars having current density of 130 A/ sq. cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every meter, adopter box and copper flexible for joints, continuous earthing with 2 Nos. aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required (From TR & DG to LT Panel) |
| 692 | 1000 A, Isc = 50 kA for 1 second |
| 693 | 3200 A, Isc = 50 kA for 1 second |
| 694 | RISING MAIN & ACCESSORIES :- Supplying, Installing on Wall, Testing and Commissioning of following capacity Air Insulated Compact Type Rising Mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos. aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every meter, continuous earthing with 2 Nos. aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required. |
| 695 | 500 A Isc = 50kA for 1 second |
| 696 | Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required |
| 697 | 400 A 30kA SC for 1 sec |
| 698 | Supplying, Installation, Testing & Commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ rising mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB (but without MCCB) complete etc. as Required |
| 699 | 100/125 A 25kA SC for 1 sec |
| 700 | 160/200 A 25kA SC for 1 sec |
| 701 | 63 A 25kA SC for 1 sec |
| 702 | Supplying, Installation, Testing & Commisioning of following capacity MCCB for existing End feed Unit/Tap Off Box. |
| 703 | 4 pole MCCB,63/100A,30KA |
| 704 | 4 pole MCCB, 160/200A, 36KA |
| 705 | 4 pole MCCB,630A, 50KA |
| 706 | Supplying, Installation, Testing & commissioning of 3 phase dual source, double recharge prepaid enery meter along with all communication cables, controler etc as required to complete the job complete in all respect upto entire staisfaction of engineer incharge. |
| 707 | Supplying, Installation, Testing & commissioning of 1 phase dual source, double recharge prepaid enery meter along with all communication cables, controler etc as required to complete the job complete in all respect upto entire staisfaction of engineer incharge. |
| 708 | Supplying of Following Sizes of 1.1 KV Grade MulticoreAluminium Conductor XLPE Insulated armoured cable conforming to IS:7098 (Part - I) complete with all Amendments etc. as Required |
| 709 | 3.5 C X 300 Sq.mm Al. XLPE arm. |
| 710 | 3.5 C X 240 Sq.mm Al. XLPE arm. |
| 711 | 3.5 C X 185 Sq.mm Al. XLPE arm. |
| 712 | 3.5 C X 150 Sq.mm Al. XLPE arm. |
| 713 | 3.5 C X 120 Sq.mm Al. XLPE arm. |
| 714 | 3.5 C X 95 Sq.mm Al. XLPE arm. |
| 715 | 3.5 C X 70 Sq.mm Al. XLPE arm. |
| 716 | 3.5 C X 50 Sq.mm Al. XLPE arm. |
| 717 | 3.5 C X 35 Sq.mm Al. XLPE arm. |
| 718 | 4 C X 25 Sq.mm PVC CUarm. |
| 719 | 4 C X 16 Sq.mm Al. XLPE arm. |
| 720 | 2 C X 6 Sq.mm Al. XLPE arm. |
| 721 | LT CABLE LAYING Laying of One Number PVC Insulated And PVC Sheathed / XLPE Power Cable of 1.1 kV Grade of Following Size Direct in Ground Including Excavation, Sand Cushioning, Protective Covering and Refilling the Trench etc. as required. |
| 722 | Upto 35 sq. mm |
| 723 | Above 35 sq. mm and upto 95 sq. mm |
| 724 | Above 95 sq. mm and upto 185 sq. mm |
| 725 | Above 185 sq. mm and upto 400 sq. mm |
| 726 | LT CABLE JOINTING & END TERMINATION Supplying and Making End Termination With Brass Compression Gland and Aluminium lugs for Following Size of PVC Insulated and PVC Sheathed / XLPE Aluminium Conductor Cable of 1.1 kV Grade as Required. |
| 727 | 2 X 6 sq. mm (19mm) |
| 728 | 4 X 16 sq. mm (28mm) |
| 729 | 4 X 25 sq. mm (28mm) |
| 730 | 3½ X 35 sq. mm (32mm) |
| 731 | 3½ X 50 sq. mm (35mm) |
| 732 | 3½ X 70 sq. mm (38mm) |
| 733 | 3½ X 95 sq. mm (45mm) |
| 734 | 3½ X 120 sq. mm (45mm) |
| 735 | 3½ X 150 sq. mm (50mm) |
| 736 | 3½ X 185 sq. mm (57mm) |
| 737 | 3½ X 240 sq. mm (62mm) |
| 738 | 3½ X 300 sq. mm (70mm) |
| 739 | HT CABLE AND ACCESSORIES Supply of H.T. Cable Supply & Testing of following 11 KV( UE) grade multicore Aluminium conductor XLPE insulated cable, insulation screening withextruded semi conducting compound in combination with copper tape armoured cores laid up, inner sheath of PVC tape, galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS: 7098 (Part - II) and complete with all latest amendments etc. complete as required. |
| 740 | 3 C x 240 Sq. mm11 KV (UE) |
| 741 | H.T. Cable Laying-DSR ITEM Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. |
| 742 | Above 120 sq. mm and upto 400 sq. mm |
| 743 | H.T Termination: DSR ITEM Supply and making Indoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV (UE) grade as required. |
| 744 | 3 C x 240 Sq.mm ( 11KV UE ) |
| 745 | Supply and making Outdoor cable end jointing with cast resin compund, including lugs and other jointing materials for following size of 3 core, XLPE aluminium conductor cable of 11KV ( UE )grade as required. |
| 746 | 3 C x 240 Sq.mm ( 11KV UE ) |
| 747 | Supply and Making Straight Through Cable Jointing With Cast Resin Compund, Including Ferrule & Other Jointing Materials for Following Size of 3 core, XLPE Aluminium conductor cable of 11KV ( UE )grade as required. |
| 748 | 3 C x 240 Sq.mm ( 11KV UE ) |
| 749 | MISCELLANEOUSITEMS Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 750 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single Red colour on front side as required. |
| 751 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. |
| 752 | Above 6.5 metre and upto 8.0 metre |
| 753 | Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape , Hole Seeling to be done complete as required. |
| 754 | 32 mm dia |
| 755 | SITC of shock treatment chart (prescribed under I.E.rules) duly framed with glass and supported from back with hard board with supply of all material labour T & P etc for proper completion of work. (Approx front area = 1.20 sq M) |
| 756 | SITC of First aid box as approved by Indian red cross conforming to IS : 2217. |
| 757 | SITC of CO2 Fire Extinguishers 4.5 kg capacity complete in all respect ISI : 15683 marked |
| 758 | SITC of ABC FIRE EXTINGUISHER 4 KG capacity complete in all respect ISI : 15683 marked |
| 759 | SITC of Fire Bucket stand made of M S angle suitable for and with 4 Nos Fire Buckets of 9.5 Ltrs capacity |
| 760 | SITC ofof rubber gloves of 11 KV grade as per IS : 4770. |
| 761 | Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. |
| 762 | SITC of ANTI SKID RUBBER MAT 1 mtr x 2 mtr. 3mm thick ISI - 15652 marked |
| 763 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching. |
| 764 | 300 mm dia |
| 765 | 250 mm dia |
| 766 | 100 mm dia |
| 767 | SUB-HEAD- VI EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required..(BODY EARTHING) |
| 768 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.. (NEUTRAL EARTHING) |
| 769 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 770 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 771 | Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required. |
| 772 | Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 773 | SUB-HEAD- VII- SOLAR POWER SYSTEM Supply,Installation,TestingandCommissioningofongridSolarPhotovoltaicPowerPlantconformingtoMNREspecificationsasamended,consistingofMono Crystallinesiliconsolarcells,netmeteringfacility,necessaryprotections,earthing,mountedonAluminium/GIstructureofsuitablestrengthwithfollowingcomponents complete as required:- |
| 774 | a)SolarPhotovoltaicModuleofcapacity540Wporabove,manufacturedinIndia,conformingtoIS14286/IEC61215,IS/IEC61730-Part-1,IS/IEC61730-Part 2.SolarPhotovoltaicModuleconversionefficiencyshallnotbelessthan16.5%.PVmodulesusedinsolarpowerplants/systemsmustbewarrantedfortheiroutputpeakwattcapacity,whichshouldnotbelessthan90%attheendof10yearsand80%attheend of 25 years. |
| 775 | b)PowerConditioningUnit(PCU)of350800VDCInputvoltagerangeand400VAC,threephase,4wire,50Hz+/2.5Hz,outputvoltagesuitabletogenerateACPowerwithefficiencynotlessthan97%,totalharmonicdistortionlessthan3%andsuitableforambienttemperaturefrom0to50degreeC.ThePCUshalladjustthevoltage and frequency level to suit the Grid Voltage Frequency. |
| 776 | c) Data Monitoring System complete with accessories. |
| 777 | d)FixingofArrayjunctionbox&MainjunctionboxwithIP65protectionandterminationarrangementforincomingandoutgoingcablealongwithglands,lugsand other accessories etc. as required. |
| 778 | e) Lightning and surge voltage protection. |
| 779 | f)Connections&Interconnectionsbysupplying&fixingrequiredsizeXLPEinsulatedcopperconductor1.1kVgradearmouredpowerandcontrolcablesbetweensolarmodules,mainpowercabletogridsupplyPCUunitalongwithsupplying&fixingofnecessarychannel/conduitlugsandotheraccessoriesetc.asrequired. |
| 780 | BOOM BARRIER RFID base boom barier with 6 metre wide Strong aluminium arm with rubber guard, Strong aluminium arm with rubber guard, Manual lock release by key in case of power failure, Green light and red light indicating the position of the beam, Connections for infrared photocell, loop detector & IC system for other functions, Stop and reverse operation safety devices, Provision for connecting an RFTD system. |
| 781 | Function Open the door by scanning the tag. After being stopped for a specific time, the system will automatically send a signal to close the barrier The system can be configured with an ro card reader, allowing addition and deletion of users. Technical Specification Clear opening width 6 mtr |
| 782 | Power Supply- 230 V ~I 50 - 60 Hz Control Panel- 24V Torque- 250Nm Opening Time- 1 - 2 s/90° Protection Rating- IP 54 Operating Temprature- -20 degreeto +50 degree Travel Control System- Encoder RFlD UHF readers to enable the tagged vehicle identification from 10-12 meter distance so that it is convenient for drivers to access the boom barrier without stopping the vehicle. |
| 783 | Teachnical Feature: Frequency- 865-867 MHz Power Output- 865-867 MHz Communication- 10/100 BaseT Ethernet (RJ45); USB Host & Client T e A & B) or Serial DB9) Operating Temprature- -20 degreeto +50 degree Humidity- 5-95% non-condensing |
| 784 | CIRCUIT CUM POINT WIRING Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit with modular switch modular plate suitable GI box and earthingthe point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required. |
| 785 | Group C |
| 786 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 787 | Wiring for the following light point with 2.5 sq.mm PVC insulated copper conductor 1100 volts grade stranded flexible FRLS wires of approved make in concealed or surface mounted 25mm dia 16 gauge MS conduit including provinding and controlled by SPMCB provided in the DB. (Cost of MCB not to be including here ) complete in all respect and as per direction of Engineer in charge. |
| 788 | Primary point controlled by one MCB. |
| 789 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steelconduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. |
| 790 | Wiring for power plug points with 2 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along with 1 No. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 791 | Wiring for light plug points / power plug points with 4 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along with 2 Nos. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 792 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as required |
| 793 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 794 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 795 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 796 | 4x 10 sqmm+ 2x 6 sqmm earth wire |
| 797 | 4x 16 sqmm+ 2x 6 sqmm earth wire |
| 798 | Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required |
| 799 | 25mm |
| 800 | Supply & fixing of following sizes of medium class PVC conduit along with accessories in surface / recessed including cutting the wall & making good the same in case of recessed conduit as required. |
| 801 | 32 mm dia. |
| 802 | Supplying and fixing of Stepped type 2 module electronic fan regulator on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 803 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 804 | Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing3 pin 5/6 Amp modular socket outlet and 5/6 A modular switch, connection etc. as required. |
| 805 | Supplying and fixingsuitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing6 pin5/6 & 15/16 Amp modular socket outlet and 15/16 A modularswitch, connection etc. as required. |
| 806 | Supplying & fixing of 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required. |
| 807 | Supplying and fixing extra conduit down rod of 20 cm lengthG.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored) |
| 808 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 809 | Upto 450 mm sweep |
| 810 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing |
| 811 | DISTRIBUTION BOARD Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 812 | 6 way, Double door |
| 813 | 8 way, Double door |
| 814 | 12 way, Double door |
| 815 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator). |
| 816 | 6 way (4 + 18), Double door |
| 817 | 8 way (4 + 24), Double door |
| 818 | 12 way (4 + 36), Double door |
| 819 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 820 | Single pole |
| 821 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 822 | Supplying and fixing following rating, double pole, 240 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 823 | 32 amps |
| 824 | Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 825 | 40 amps |
| 826 | 63 amps |
| 827 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 828 | 25/32 amps |
| 829 | 40 amps |
| 830 | 63 amps |
| 831 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 832 | Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 833 | Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 834 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 835 | LIGHTING FIXTURE & FAN & LIGHTING CONTROL Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting complete with all accessories including connections etc. as required |
| 836 | Supply of Light fixture as given below Supply of 36 W recess mounted LED back-lit 2’x2’ withhigh efficient LED’s, CCT 5700 - 6500 K,CRI=80, System lumen 100lm/W, Lumens = 3600, white powder coated CRCA with PMMA opal diffuser for glare free & uniform lighting, minimum burning hour life >50000 hours. Driver shall be of constant current type, operating temperature from -10 to +45 degree celcius, power factor>0.95, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 837 | Supply of 36 W recess mounted LED back-lit 2’x2’ withhigh efficient LED’s, CCT 5700 - 6500 K,CRI=80, System lumen 100lm/W, Lumens = 3600, white powder coated CRCA with PMMA opal diffuser for glare free & uniform lighting, minimum burning hour life >50000 hours. Driver shall be of Dimable type, operating temperature from -10 to +45 degree celcius, power factor>0.95, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 838 | Supply of recess mounting 18 W LED down lightwith 50000 burning hours. high efficient LED’s, CCT-5700k -500 K,CRI >80, Lumens = 1800, single piece pressure die cast powder coated housing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 839 | Supply of recess mounting 12 W LED down light with 50000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens = 100lumen/watt, with aluminium die casthousing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 840 | Supply of surface mounting 12 W LED down light with 50000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens = 100lumen/watt, with aluminium die casthousing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 841 | Supply of recess mounting 6 W LED down light with 40000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens = 90lumen/watt, with aluminium die casthousing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 842 | Supply of recess mounting 7 W LED COB down light with 40000 burning hours high efficient LED’s, CCT-5700-6500 K,CRI >80, Lumens = 90lumen/watt, with aluminium die casthousing with opal diffuser for glare free & uniform lighting, Driver shall be of constant current type, operating temperature from -10 to +45degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 843 | Supply of E27 base decorative type single headed wall mounted light fixture. Housing made of Metal, Synthetic, glass in Bronze finish. Operating voltage 220-240V, 50Hz. Make- Philips- Model No. Philips 31425 / Havells- Model No. LHJE01104499/ Bajaj- Model No.- 112775. |
| 844 | Supply & erection of 20 watt LED Betten Tube Light, 4" long suitable with 40000 burning hours for rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply with aluminium alloy base,, frosted polycarbonate diffusers with power factor >0.90, Total Harmonic Distortion (THD) < 20%, system current - 0.085A, system efficiency > 85% , with operating temp. -10° C to 45° C, Lumen output for LED tube should be > 2000 lumen and overall lumen/watt of luminaire should be greater than 80%, C.R.I. of LED>80% with correlated colour temperature (CCT) of 6500K , minimum burning hour life >40000 hours,LED viewing angle 120 Degree complete in all respect with the entire satisfaction of the Engineer-in-incharge. Supply of Industrial General Purpose 4" long tube fitting suitable to house 1x20w LED tube rod 4" long, Polycarbonate housing , rated voltage 240 V and Ingress protection IP-20 complete in all respect with the entire satisfaction of the Engineer-in-incharge. |
| 845 | Supply of LED Bulkhead with a nominal system lumen output of 700 lumens and a minimum system efficacy of 105 lm/W. The luminaire shall have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 5700K and CRI > 80. The luminaire shall meet IP65 rating and IK 08 rating with THD < 20% and PF > 0.9. The luminaire housing should made ofpressure die cast Aluminium with polycarbonate front diffuser. The total power consumption should not exceed 6.5W (including driver). |
| 846 | Supply of 11 W mirror light with high efficient LED’s, CCT-6500 K,CRI >70, Lumens =900, with Ingress protection IP-20, with 50000 burning hours Driver shall be of constant current type, operating temperature from -10 to +45 degree celcius, power factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A"c , 50 Hz +_ 5%, AC supply. Surge protection - Inbuilt 2.5KV. Complete in all respect with the entire satisfaction of Engineer-in-Charge. |
| 847 | Supply of LED exit signage of Box size in mm 325x425x365(Make- Prolite, Model No.PEL LED E/NM (RM) W, Code No. E 109) or Equivalent to Philips, Trilux, Havels . |
| 848 | Supply of LED aviation light luminaire (Make Havells, Philips or equivalent). |
| 849 | Supplying of Plastic Body Ornamental Exhaust Fan heavy duty 230V A.C 50 cycles, 300 mm sweep, 1300 rpm, energy efficient, complete erected in position with all accessories. Make- Havels- Venti Air DS, or Equivalent to Orient- Ventilator DS, Cromptong & Greaves- Ventilus 250 or equivalent as per specification. |
| 850 | Supplying of wall bracket fan 230V A.C 50 cycles, 400 mm sweep, energy efficient, complete erected in position with all accessories. |
| 851 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 852 | Supplying,Installation,Testing and Commissioning of Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10 Amp, for mounting height up to 2.8 meter and for 5 meter diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. |
| 853 | Supply of 500W Chandlier having dia 4.5 Mtr suspended in ceiling with all required accessories. |
| 854 | Supply of 500W Chandlier having dia 2.5 Mtr suspended in ceiling with all required accessories. |
| 855 | Lighting Automation Supply, Installation,Testing & Commissioning of Lighting processor has built-in astronomical clock. Processor Link- 2 RJ-45 ports with built in switch for daisy chaining processors (max 16 processors).Shpuld supportintegration with third-party systems and communication between multiple processors. processors may be connected using either an Ethernet hub /switch or router, or by using Ethernet directly from a PC to the processor. Power : Processor (P): 24–36 V - 250 mA; Links (L1 / L2): 24–36 V - 2 A per link. Regulatory Approvals : cULus, NOM, CE, Cooling Method : Passive Cooling. Should be supplied with standard accessories as required. Approved Make:Lutron/Zumtobel/Leviton |
| 856 | Supply, Installation,Testing & Commissioning of power supply for above processor, Input Power: • Nominal input voltage: 100–277 V~, • Frequency: 50/60 Hz, • Current consumption, fully loaded (typical): 0.7 A (230 V~). Power Supply Output: • Nominal output voltage and tolerance:24 V- / ±1%, 75 Power Draw Units (PDUs), • 2.5 A SELV / PELV / NEC® Class 2, • Power Draw Units (PDUs): Supplies 75 PDUs maximum. Approved Make:Lutron/Zumtobel/Leviton |
| 857 | Supply, Installation,Testing & Commissioning of Wire Landing Board, wire landing board is a wiring aid consisting of a printed circuit board with one set of five terminal blocks. Approved Make:Lutron/Zumtobel/Leviton |
| 858 | Supply ofLow Voltage Enclosure provides a compact housing for mounting one processor or one system interface and up to two wire landing boards. Approved Make:Lutron/Zumtobel/Leviton |
| 859 | Supply, Installation,Testing & Commissioning of DIN Rail mounted 4-zone Switching module, Each zone is rated at 5A for switching ofinductive, capacitive, or resistive loads. Includes communication link to any device (max 100) and one contact closure input /output link, Should be Rated for lighting loads as defined by IEC/EN 60669 as well as INC, MLV, and ELV, 220-240 V~ 50/60 Hz, Single input feed, Lightning strike protection meets ANSI/IEEE standard C62.41 and IEC 61000-4-5. Can withstand voltage surges up to 6000 V~ and current surges up to 3000 A. Approved Make:Lutron/Zumtobel/Leviton |
| 860 | Supply, installation, testing and commissioning of Direct dimming module, with 4 feed suitable with 10 A maximum total input current for leading/ trailing edge dimming outputs. Should have a bypass contact closure input builtin without connecting any external devices . Each zone has no minimum load requirement. Should support One load type per zone. Should be RoHS Compliant, IEC/EN 60669-2-1, CE marked. Approved Make:Lutron/Zumtobel/Leviton |
| 861 | Supply, Installation,Testing & Commissioning of motor control power module,Input voltage: 230 V~ 50/60 Hz,6 A maximum total input current, BTU/hour when fully loaded: 5, Ambient temperature operating range (inside mounting panel): 0 ºC to 40 ºC (32 ºF to 104 ºF), Each motor control power module counts as 4 zones (outputs) and 1 device . Approved Make:Lutron/Zumtobel/Leviton |
| 862 | Supply of Wireless Occupancy/Vacancy Sensor for rooms with a frequency of 865 MHz, Ceiling mount, infrared, 37.2 sq m (400 sq ft), battery-powered, 102 mm (4.0 in) diameter, white. Approved Make:Lutron/Zumtobel/Leviton |
| 863 | Supply of Sensor Module, to connect 10 numbers of sensors either of the Occupancy / Daylight / Personal sensors/Pico. No wired connections, ceiling mount Approved Make:Lutron/Zumtobel/Leviton |
| 864 | Supply, installation, testing and commissioning of wall-mounted 4-button Keypad, wired keypad allows the user to control lights, shades/ draperies, temperature, and 3rd-party equipment. Large buttons are easy to use and button engraving is easy to read. Buttons with white, backlit engraving make it easy to find and operate the keypad in low light conditions. Keypads are available in a variety of colors, finishes, and button marking options. Approved Make:Lutron/Zumtobel/Leviton |
| 865 | Supply, installation, testing and commissioning of wireless control keypad, flexible and easy to use device that allows the user to control wireless load-control devices from anywhere in the space. Can provide control of blinds, curtains, or lighting devices within a range of 30 ft (9 m) through walls and 60 ft (18 m) line-of-sight. Should be BAA-compliant. Approved Make:Lutron/Zumtobel/Leviton |
| 866 | Supply, installation, testing and commissioning of distribution boxes that serve as the load centre and distribution of power. Approved Make:Custom |
| 867 | Supply, Installation, Testing and Commissioning of6 conductors Control Non-Plenum rated cable with 2x 12 AWG, 1 x 18 AWG, 2 x 22 AWG and 1x 24 AWG drain. Approved Make:Lutron/Zumtobel/Leviton |
| 868 | Supply, installation, testing and commissioning ofCurtain Motor -35 KGcontrolled by automation. Nominal torque: 0.6 Nm, Maximum stall torque:0.7, No load speed: 105 rpm, Nominal speed: 105 rpm, Working temperature:0°C to +60°C 85%HR at 35°C, Voltage range: 90 to 264 Vac, Frequency range: 47 to 63HZ, Maximum Current(A): 0,6 at 120VAC ; 0,3 at 240VAC, Approved Make:Lutron/Somfy |
| 869 | Supply, installation, testing and commissioning of CurtainTrack 2-3 metre. Approved Make:Lutron/Somfy |
| 870 | Supply, installation, testing and commissioning of CurtainTrack 6-7 metre. Approved Make:Lutron/Somfy |
| 871 | Supply, installation, testing and commissioning of Extra track @1 meter Approved Make:Lutron/Somfy |
| 872 | Supply, installation, testing & commissioning of Set of 2 Nos. 100 KVA/80 KW UPS. Each UPS of 100KVA should have following specifications in addition to tender requirements : True online double conversions, IGBT Rectifier & inverter based UPS. Three phases Input/ three phase output with SMF batteries complete with MS Fabricated battery rack to accommodate the all battery system, Suitable for 30 Min backup on Full load at 0.8 Load P.f., with 65 nos. 120AH Battery with Each UPS, Input voltage operations on mains without switch over to battery : 340-478V at 100% load, 220-478 V @ 50% load. Input power factor 0.99 @ 100% linear load, input THDi less than 5% @ 100% linear load. Output THD is less than 3% for full linear load & Less than 5 % for nonlinear load. Crest factor 3:1, over load 125% for 10 min, 150% for 1 min, UPS should be able to operate continuously at 115% load on bypass mode. Battery Flexible design shall be available from 36 to 40 or better. Battery type should be Valve regulated lead-acid (VRLA). Inbuilt Delta - Star Input Isolation Transformer with each UPS Shall be provided, parallel communication port, RS232, USB, EPO and SNMP interface, BMS interface, Dust Filter at Air Inlet point are required |
| 873 | LCD Display indicating all important parameters. To improve the UPS Security over LAN/WAN the SNMP card provided with UPS shall be having Cybersecurity enhancements for IEC / UL 2900-2-2 certification, including stronger encryption, configurable password policy. The card shall work on GIGABIT Speed and should support all major protocols. UPS shall be provided with Temperature Humidity Sensors to monitor Temperature and Humidity over LAN through SNMP card Software. Battery open rack with top cover, battery interlinks, battery breaker(MCCB), Battery breaker enclosure, battery to UPS cable as required should be provided with UPS systems. UPS system shall be parallelable upto 4 units in case required in future. Each UPS shall be compatible for working in parallel redundant mode with other and should be able to be used with Lithium Ion Batteries if required in future. Offered UPS Model shall be type tested in line with IEC 62040-3 standard from third party NABL Approved lab. UPS Make: APC, Powerware, Gutor, Eaton, GE, ABB Battery Make: Panasonic, Exide, Quanta, Amara Raja |
| 874 | LIFT WORK Supply, errection, testing & commissioning of 13 passanger with machine Electric Traction Elevator, to be errected in accordance with followingTechnical Specification & as per latest IS Specifications. |
| 875 | Nos. of Lifts 1 Nos. Type & Capacity:Passanger Elevator App. 884 kg. 13 person. Speed mps : 1.5 mtr per second Travelling (max.)in mtrs : Approx. 36.3 mtrs Serving : 11 stops, 11 opening (All opening on the same side). Power Supply : 415V, 3 phase, 50 HZ AC supply. Control : Simplex full collectivecontrol with or without attendant. Operation : Automatic Motor : A Synchronous motor Car Size : as per manufacturer design. Door Frame : Full Glass Door. Well Size-2.5 M deep x 2.0 M wide |
| 876 | Other Features : Battery operated emergency alarm and emergency light with rechargeable battery. Adjustable guide shoes. Combine Luminous hall buton and digital hall indicator/touch screen. Integral full height car opening panel with luminouscombined with direction arrows, overload warning indicacator & service cabinet. Hand free press & speak intercom with EPABX for three way communication. Automatic rescue device to automatic bring the elevator to a landing in case of power / phase failure/ low voltage. |
| 877 | Full height Infrared safety curtain & automatic floor announcer. Diffused Lighting in car. Blower (noiseless) Looking mirror in front side of lift car. Face Plate finish : Stainless stell in hairline. Face Plate : Rectangular. The Three feet high railing shall be provided on car top. The motor shall be high starting torque and low starting current and shall be arranged for self lubrication. Proper weight screen shall be provided at the hoist way. Fire retardant compound coated traveling cable shall be used. 2Phase Device Fire Man Drive & Fireman switch at ground floor. Load Weight device with overload bypass feature. Steel itels such as Door Frames Sill angles, Fascia Plates, Spring Buffers. Bralite Features, Lift announcement system, Pit ladder, Hand Rail & Additional Car Gate Lock. |
| 878 | Three side Hand Rail in Stainless Steel Finish. System Capable of withstanding +10% to -10% Variation in Supply Voltage Fluctuations. Car Plateform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel. Fire Rated landing Doors for a period of two hours only. The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice & vibration. |
| 879 | Supply, errection, testing & commissioning of 13 passanger with machine room Electric Traction Elevator, to be errected in accordance with followingTechnical Specification & as per latest IS Specifications. |
| 880 | Nos. of Lifts 1 Nos. Type & Capacity:Passanger Elevator App. 884 kg. 13 person. Speed mps : 1.5 mtr per second Travelling (max.)in mtrs : Approx. 23.0 mtrs Serving : 7 stops, 7 opening (All opening on the same side). Power Supply : 415V, 3 phase, 50 HZ AC supply. Control : Simplex full collectivecontrol with or without attendant. Operation : Automatic Motor : A Synchronous motor Car Size : as per manufacturer design. Door Frame : Full Glass Door. Well Size-2.5 M deep x 2.0 M wide |
| 881 | Other Features : Battery operated emergency alarm and emergency light with rechargeable battery. Adjustable guide shoes. Combine Luminous hall buton and digital hall indicator/touch screen. Integral full height car opening panel with luminouscombined with direction arrows, overload warning indicacator & service cabinet. Hand free press & speak intercom with EPABX for three way communication. Automatic rescue device to automatic bring the elevator to a landing in case of power / phase failure/ low voltage Full height Infrared safety curtain & automatic floor announcer. Diffused Lighting in car. Blower (noiseless) Looking mirror in front side of lift car. Face Plate finish : Stainless stell in hairline. Face Plate : Rectangular. The Three feet high railing shall be provided on car top. The motor shall be high starting torque and low starting current and shall be arranged for self lubrication. |
| 882 | Proper weight screen shall be provided at the hoist way. Fire retardant compound coated traveling cable shall be used. 2Phase Device Fire Man Drive & Fireman switch at ground floor. Load Weight device with overload bypass feature. Steel itels such as Door Frames Sill angles, Fascia Plates, Spring Buffers. Bralite Features, Lift announcement system, Pit ladder, Hand Rail & Additional Car Gate Lock. Three side Hand Rail in Stainless Steel Finish. System Capable of withstanding +10% to -10% Variation in Supply Voltage Fluctuations. Car Plateform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel. Fire Rated landing Doors for a period of two hours only. The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice & vibration. |
| 883 | Supply, errection, testing & commissioning of 13 passanger with machine room Electric Traction Elevator, to be errected in accordance with followingTechnical Specification & as per latest IS Specifications. |
| 884 | Nos. of Lifts 1 Nos. Type & Capacity:Passanger Elevator App. 884 kg. 13 person. Speed mps : 1.5 mtr per second Travelling (max.)in mtrs : Approx. 30.0 mtrs Serving : 9 stops, 9 opening (All opening on the same side). Power Supply : 415V, 3 phase, 50 HZ AC supply. Control : Simplex full collectivecontrol with or without attendant. |
| 885 | Operation : Automatic Motor : A Synchronous mot or Car Size : as per manufacturer design. Door Frame : Full Glass Door. Pit Size- 23.0 M deep x 2.45 M wide Other Features : Battery operated emergency alarm and emergency light with rechargeable battery. Adjustable guide shoes. Combine Luminous hall buton and digital hall indicator/touch screen. Integral full height car opening panel with luminouscombined with direction arrows, overload warning indicacator & service cabinet. |
| 886 | Hand free press & speak intercom with EPABX for three way communication. Automatic rescue device to automatic bring the elevator to a landing in case of power / phase failure/ low voltage. Full height Infrared safety curtain & automatic floor announcer. Diffused Lighting in car. Blower (noiseless) Face Plate finish : Stainless stell in hairline. Face Plate : Rectangular. The motor shall be high starting torque and low starting current and shall be arranged for self lubrication. Proper weight screen shall be provided at the hoist way. Fire retardant compound coated traveling cable shall be used. 2Phase Device Fire Man Drive & Fireman switch at ground floor. |
| 887 | Load Weight device with overload bypass feature. Steel itels such as Door Frames Sill angles, Fascia Plates, Spring Buffers. Bralite Features, Lift announcement system, Pit ladder, Hand Rail & Additional Car Gate Lock. Three side Hand Rail in Stainless Steel Finish. System Capable of withstanding +10% to -10% Variation in Supply Voltage Fluctuations. Car Plateform constructed out of Cold Rolled Grain Oriented Formed Sheets of Steel. Fire Rated landing Doors for a period of two hours only. The whole machinery shall be mounted on appropriate anti vibration supports to minimize voice & vibration. |
| 888 | LINEAR PNUEMATIC HEAT DETECTION TUBE SYSTEM Supply, Installation, Testing and Commissioning of 2.5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 2.5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation. |
| 889 | Supply, Installation, Testing and Commissioning of 5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation. |
| 890 | Supply, Installation, Testing and Commissioning of 10 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 10 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation. |
| 891 | Supply, Installation, Testing and Commissioning of Linear pneumatic heat Detection Tube with all necessary fittings & supports. |
| 892 | Supply, Installation, Testing and Commissioning of Master Control Unit with Audio Visual Alarm with wiring to make complete system operational . Thecontrol Panel should have provision for integration with fire Alarm /SCAD/BMS System. |
| 893 | LIGHTNING PROTECTION SYSTEM Supply of Earthing terminationmade of copper-bonded rod of 10 feet length,14 mm dia. (Minimum copper bonding shall be 0.25mm) along with Rod-to-Conductor connectors, Earth enhancement material (25 KG resistivity each less than 0.12 ohm meter), Pit Cover and other accessories as required and as per r and other applicable codes. |
| 894 | Providing and fixing of lightning conductor finial, made of 25 mm dia 1200 mm long, copper tube, having single prong at top , with 85 mm dia 3 mm thick copper base plate including holes with insulation etc. complete as required. |
| 895 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) |
| 896 | Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run). |
| 897 | Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 898 | Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. |
| 899 | CABLE TRAY Supports, bends, access boxes, tap off boxes and cross over as per site requirement. (overhead / wall mounted recovery & junction boxes shall be 2.0 mm thick). The pregalvenised sheet shall be as per IS 277 or BS 2989 having tensile strength of minimum 500 N/sq.m. and minimum zinc coating of 275 GSM. |
| 900 | Supplying, installation, testing & commissioning of Race way made from minimum 2.0 mm thick GI raceway, factory fabricated, with internal partition of the following sizes including providing removable double folded cover of 2.0 mm thick , knock out holes and fixing accessories & coupling, earthing stud for terminating 8 SWG copper earth wire completeas required |
| 901 | 100 mm wide x38 mm deep in ceiling/floor |
| 902 | 150 mm wide x38 mm deep in ceiling/floor |
| 903 | 225 mm wide x38 mm deep in ceiling/floor |
| 904 | 300 mm wide x38 mm deep in ceiling/floor |
| 905 | Supplying, installation, testing & commissioning offloor/ceiling recessed 2 mm thick pregavanised sheetoutlet junction box including providingcover with provision to adjust overall height, knock outs on four sides to accept raceways of specified sizes and cutouts to fix required outlets for following size of race ways with painted GI plate ( Colour as approved Architect/Consultant). |
| 906 | 150X150X50mm |
| 907 | 300X300X50 mm |
| 908 | 400X400X50 mm |
| 909 | Supplying and installing following size of perforated Hot DippedGalvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 910 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 911 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 912 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 913 | 600 mm width X 50 mm depth X 2 mm thickness |
| 914 | 900 mm width X 62.5 mm depth X 2.0 mm thickness |
| 915 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 916 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 917 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 918 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 919 | 600 mm width X 50 mm depth X 2 mm thickness |
| 920 | 900 mm width X 62.5 mm depth X 2.0 mm thickness |
| 921 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 922 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 923 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 924 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 925 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 926 | 900 mm width X 62.5 mm depth X 2.0 mm thickness |
| 927 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Cross member” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 928 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 929 | 150 mm width X 50 mm depth X 1.6 mm thickness |
| 930 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 931 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 932 | 900 mm width X 62.5 mm depth X 2.0 mm thickness |
| 933 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 934 | 100 mm width X 50 mm depth X 1.6 mm thickness |
| 935 | 50 mm width X 50 mm depth X 1.6 mm thickness |
| 936 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 937 | 600 mm width X 50 mm depth X 2.0 mm thickness |
| 938 | 900 mm width X 62.5 mm depth X 2.0 mm thickness |
| 939 | Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll/Rotary Compressor(s), minimum two compressors for above 14HP modules, microprocessor based Controller, topdischarge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundationetc. completeas required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase, 50HzAC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRIconditions shall not be less than 3.1 and IEER not less than 6.5 |
| 940 | 22 HP Outdoor unit VRV/VRF |
| 941 | 24 HP Outdoor unit VRV/VRF |
| 942 | 26 HP Outdoor unit VRV/VRF |
| 943 | 28 HP Outdoor unit VRV/VRF |
| 944 | 30 HP Outdoor unit VRV/VRF |
| 945 | 40 HP Outdoor unit VRV/VRF |
| 946 | Supply, installation, testing and commissioning of following minimum capacity4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable mediapre-filter, fansection with low noise fan/dynamically balanced blower, multispeed motor, coilsection with DXCoppercoil electronic expansion valve, outercabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operationon single phase 230V±10%, 50Hz ACsupply, complete as required. The unit shall have automatic force shut down provisionin case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at airinlet conditions of 27Degree CD Band 19 Degree CWB temperature. |
| 947 | 0.8 TR |
| 948 | 1 TR |
| 949 | 1.2TR |
| 950 | 1.6 TR |
| 951 | Supply, installation, testing and commissioning of following minimum capacity and externalstatic pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/ dynamically balancedblower, multispeedmotor,coil section with DX copper coil,electronic expansionvalve, cordedremote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ±10%,50Hzcompleteasrequired.Theunitshallhaveautomatic forceshutdown provisionincaseoffireonreceiveingsignalfrom BMS System.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. Low static ductable units (minimum 25 pascal external static pressure) |
| 952 | 1.3 TR |
| 953 | 1.6 TR |
| 954 | Mid Static Ductable units (minimum 45 pascal external static pressure) |
| 955 | 2.0 TR |
| 956 | 2.6 TR |
| 957 | 4 TR |
| 958 | High Static Ductable units (minimum 110 pascal external static pressure) |
| 959 | 7.1 TR |
| 960 | 8 TR |
| 961 | Supply, Installation, testing and commissioning including vaccumiazationandNitrogentestingoffollowingnominalsizesof soft/hard drawn copper refrigerant piping for VRV/VRF system, completewithfittings,withsuitable adjustableringtypehanger supports, jointing/brazing includingaccessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction andLiquid lines, all accessories as per specifications etc. as required |
| 962 | 6.4 mm dia (OD) (Soft drawn) withtube thickness 1.2 mm with 19 mm thickinsulation |
| 963 | 9.5 mm dia (OD) (Soft drawn) withtube thickness 1.2 mm with 19 mm thickinsulation |
| 964 | 12.7mmdia(OD)(Softdrawn)with tubethickness1.2mmwith19mm thick insulation |
| 965 | 15.86 mm dia (OD) (Soft drawn) withtube thickness 1.2 mm with 19 mm thick insulation |
| 966 | 19 mm dia (OD) (Hard drawn) withtube thickness 1.2 mm with 19 mm thick insulation |
| 967 | 22.2 mm dia (OD) (Hard drawn) withtube thickness 1.2 mm with 19 mm thick insulation |
| 968 | 25.4 mm dia (OD) (Hard drawn) withtube thickness 1.2 mm with 19mm thick insulation |
| 969 | 28.58 mm dia (OD) (Hard drawn) withtube thickness 1.2 mm with 19mm thick insulation |
| 970 | 31.8 mm dia (OD) (Hard drawn) withtube thickness 1.62 mm with 19mm thick insulation |
| 971 | 34.9 mm dia (OD) (Hard drawn) withtube thickness 1.62 mm with 19mm thick insulation |
| 972 | 38.1mm dia (OD) (Harddrawn) with tube thickness 1.62mm with 19mm thick insulation |
| 973 | 41.27 mm dia (OD) (Hard drawn) withtube thickness 1.62 mm with 19mm thick insulation |
| 974 | Supply,Installation , Testing and Commissioning of following imported fittings to be provided in refrigerant pipe line. Material of construction for fittings shall be similar to refrigerant piping. |
| 975 | Y- jointsforrefrigerant piping . |
| 976 | SITC of Expansion Kit cum control kit Required for the above AHU to make the system complete (Incl, Standby AHU Coil) |
| 977 | Central remote Controller (Touch Screen Type) : Supply, installation, testing & commissioning of the Graphic central remote Controller. It must act as an advanced air conditioning management system to facilitate complete control of VRF air conditioning equipment, It should be user friendly through its touch screen, icon display and color LCD display. Integratable upto 75 remote controller groups(includingAHUs) and BMS compatible with ethernet/Wi-Fi communication protocol for remote monitoring. In addition to basic controls such as settings for on/stop,the operation mode & temperature,the air quantity and auto louvercan be set.If a problem occurs, an alarm code immediately shows the detailsof the problem.An external input terminal is provided as standard.External signals enable the following function: central operation/stop,demand control,emergency stop,central operation output,& central alarm output. |
| 978 | Central remote Controller (Touch Screen Type) : Supply, installation, testing & commissioning of the Graphic central remote Controller. It must act as an advanced air conditioning management system to facilitate complete control of VRF air conditioning equipment, It should be user friendly through its touch screen, icon display and color LCD display. Integratable upto 150 remote controller groups(includingAHUs) and BMS compatible with ethernet/Wi-Fi communication protocol for remote monitoring. In addition to basic controls such as settings for on/stop,the operation mode & temperature,the air quantity and auto louvercan be set.If a problem occurs, an alarm code immediately shows the detailsof the problem.An external input terminal is provided as standard.External signals enable the following function: central operation/stop,demand control,emergency stop,central operation output,& central alarm output. |
| 979 | Supply, installation testing and commissioning of factory built floor mounted chilled water Double skin type horizintal/vertical air handling units made of 40mm ±2mm thick panels consisting of pre plasticized GI casing of thickness 0.8mm outside layerand 0.8mm inside layer with polyurethene foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required , min. 2 bend GSS/PVC eliminators, DX cooling coil section with aluminium finned copper tubes ( tube thickness not less than 0.5 mm ) cooling coil of 6 row deep, filter section with 50 mm thick metal viscous filter /washable synthetic type air prefilters, AHU Blower Direct driven with VFD , squirel cage induction motor (Plug fan with VFD) package with TEFC drive motor of efficiency class IE3 suitable for 415±10% V, 50Hz, 3 phase AC supply suitably designed for variable frequency drive applications, drain connections , stainless steel (18G) drain pain with PUF insulation,, necessary vibration isolation arrangement etc. complete as per specification & AHU schedule and of following capacities as (All AHU Eurovent certified for mechanical performance and rating performance as a whole as per EN 1886 & 13053): |
| 980 | Supply , installation testing and commissioning of Double skin floor mounted Horizontal/vertical Two pipe system (One coil)AHUs wherever required as per thementioned inAHU schedule. (All AHU Should Be BMS/VFD Compitable) Double Skin Floor Mounted Horizontal AHU With thermal break profile ,Pre Filter (MERV-8) & ESP/EAC filter .DX Coil ,65 mmwg S.P. with three Phase Motor |
| 981 | 4500 CFM/10.5 TR |
| 982 | 8000 CFM/22.5 TR |
| 983 | 12000 CFM/24.5 TR |
| 984 | Floor Mounted Horizontal Air Handling Units With Exh. Blower and Enthalpy Recovery Wheel (FM AHU) Supply, Installation Testing and Commissioning of floor mounted AHU"s. The AHU"s shall be double skin type made of 0.80 mm thick GI sheet with40+/-2 mmThickfor outdoor application PUF insulation. The Drain Pan for AHU"s shall be of SS. They shall be suitable for indoor/outdoor installation. The AHU"s selected shall be supplied with Forward / Backwarddirect driven with VFD supply air Blower Fans and exh. air blower (With VFD)with Enthalpy Recovery Wheel (Min. Efficiency of HRW is 75%) (ERW/HRW)suitable to deliver the undergiven CFM and Static. The AHU"s shall be DX coil ( complete with mixing chamber if required , AHU Included VI Pads.(All AHU Eurovent certified for mechanical performance and rating performance as a whole as per EN 1886 & 13053) |
| 985 | All AHU Should Be included Supply/Return/Fresh Air Damper & Thermal Break Profileand with three phase motor suitable for BMS Compitable. Double Skin Floor Mounted Horizontal/Vertical TFA With thermal break profile ,Pre Filter (MERV-8) ESP/EAC& Fine filter (MERV-13). DX Coil , 80 mmwg S.P. of Supply Air Fan and 60 mm wg SP of Exh. fan,Enthalpy Recovery Wheel , ,Mixing box and with three Phase Motor |
| 986 | 11500 CFM Supply Fan/9500 CFM Exh. Fan/ 42.0 TRfor TFA |
| 987 | 4700 CFM Supply Fan/3000 CFM Exh. Fan/ 14.0 TRfor TFA |
| 988 | Spcl. Note : If any AHU/TFA at terrace lvl. Than that will be with weather proof canopy so it should be cross check with dwgs. and at siteaccordingly pricing quoate . |
| 989 | Supply,installation,testing and commissioning of Certified Propeller fan of the following capacity of approved make and specification. Fan shall be supplied with aluminum gravity louver & bird screen and Speed Regulator. |
| 990 | 200 mmdia propeller fan,with single phase motor |
| 991 | 300 mmdia propeller fan,with single phase motor |
| 992 | Inline fan Supply, installation, testing and commissioning ofCertified Circular/Rectangular swing type Inline fan with fiire retardent Canvas connection Speed Regulatorof the following capacity of approved make and specification. |
| 993 | 50-450 CFM,5-7 mm SP WG with Single phase motor |
| 994 | 500-550 CFM,7-10 mm SP WG with Single phase motor |
| 995 | 600-800 CFM,10-12 mm SP WG with Single phase motor |
| 996 | Tube Axial Flow fans SITC of Long case Tube axial flow fans, as per specifications and approved makes suitable for three phase operation at 1450 RPM respectively Normal/Smoke case. |
| 997 | SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet. The electric motor coupler shall be squirrel cage induction motor (IE-3 type) confirming to IS - 325-IP - 55 with class `F" insulation.Fan efficiency should not be less than 70 %, noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions. Fans should be as per specification and drawings. (As per Vent. Fan Schedule ) (Pressurization Fans with St. Press. of 40 mmWG) |
| 998 | 9000-10000 CFM (For Stairwell/Liftwell/lobby Pressurization) |
| 999 | 21000 CFM (For Stairwell/Lift well/lobby Pressurization) |
| 1000 | 16500 CFM , 30 mmwg SP (For Normal & Make Up air Basements) |
| 1001 | 25500 CFM , 30 mmwg SP (For Normal & Make Up air Basements) |
| 1002 | 17500 CFM , 30 mmwg SP (For Make Up air ) |
| 1003 | SITC of AMCA Certified (For Air and Sound Performance) tube axial flow fan of different capacity as mentioned below in standard M.S.contruction. Entire fan model & AMCA Seal shall apear in techncial submittal of fan. All the fans are synthetic enamelled panited/hot dip galvanized with minimum 220 GSM Zinc Coating and complete with bird screen at inlet. The electric motor coupler shall be squirrel cage induction motor (IE-3 type) confirming to IS - 325-IP - 55 with class `H" insulation. Motor shall be of high temperature resistance "Class H Smoke Spill" 250° C for 2 hrs. Fan shall be EN 12101-3 Certified & CE/UL Listed for high temprature. Fan efficiency should not be less than 70 %, noise level should not be more than 80 db @ 3 m distance when measured in hemisperical reverberant room conditions for Normal mode Fans and noise level should not be more than 85 db @ 3 m distance when measured in hemisperical reverberant room conditions for Emergency mode Fans. Fans should be as per specification and drawings (As per Vent. Fan Schedule ). All Fans Should be VFD Compitable. |
| 1004 | 3500 CFM, 25 mmwg SP For Upper Floor Smoke extract |
| 1005 | 4000 CFM, 25 mmwg SP For Upper Floor Smoke extract |
| 1006 | 10500 CFM, 25 mmwg SP For Upper Floor Smoke extract |
| 1007 | 5500-6000 CFM, 25 mmwg SP For Upper Floor Smoke extract |
| 1008 | 1500-2500 CFM, 25 mmwg SP For Normal & Smoke extract |
| 1009 | 4500 CFM, 50 mmwg SP For Normal & Smoke extract |
| 1010 | 7000-7500 CFM, 30 mmwg SP For Normal & Smoke extract |
| 1011 | 12500 CFM, 25 mmwg SP For Normal & Smoke extract |
| 1012 | 16500 CFM, 25 mmwg SP For Normal & Smoke extract |
| 1013 | 21000-21500 CFM, 25 mmwg SP For Normal & Smoke extract |
| 1014 | 23000-25500 CFM, 25 mmwg SP For Normal & Smoke extract |
| 1015 | Evaporative air cooler(Air Washer) Supply , Install, test and commission double skin Evaporative air washer as per specifications , suitable for the following capacity given below at 75-90% efficiency of evaporative medium. The fan shall be of DIDW centrifugal construction. Packaged Type Ventilation fan sections of double skin construction as described above and in the specifications DIDW type,motor within the casing.All fans shall have multi speed motors Cost to be inclusive of unit isolator and .25HP-0.5HP water pump. Fan Motor VFD Compitable. AS PER SPEC. |
| 1016 | 3500 CFM, 3PH, 40 mm WG static pressure,960 rpm, .5HP motorwith Speed controller for Ceiling/floor mounted |
| 1017 | 2000 CFM, 3PH, 40 mm WG static pressure,960 rpm, .5HP motorwith Speed controller for Ceiling/floor mounted |
| 1018 | 24000 CFM, 3PH, 40 mm WG static pressure,960 rpm, 1.0HP motorwith Speed controller for floor mounted |
| 1019 | Air Scrubber (DRY Type) DIDW FAN : CSSD/Laundry/Kitchen Exhaust Supply, installation, testing and commissioning of DIDW Backword curved horizontal floor mounted fan unit comprising of accurately cut scroll & side plates, heavy gauge with all welded construction, sheet steel fabricated impeller, drive with blower pulley, motor pulley, V-belts, squirrel cage motor complete as per specification (fan-motor efficiency exceeding ASHRAE 90.1-2007 Criteria). (The bidder shall submit fan performance curves for all fans). The item should be all complete in line with relevant standards, technical specifications of the standards and direction of engineer incharge. |
| 1020 | 4000 CFM/ 75 mm WG SP |
| 1021 | 3000 CFM/ 75 mm WG SP |
| 1022 | CO SENSOR Supply, installation, testing and commissioning ofCO sensors . The car park ventilation systems shall be controlled by an individual CO-Monitoring system for entire car park located on each level to optimize efficiency. The contactors within the motor control panel shall be controlled by a Carbon Monoxide monitoring panel which shall contain DDCs (Direct Digital Controllers) where the pre-determined switching strategy and logic shall be loaded. The CO monitoring panel shall receive signals from CO sensors located throughout the levels at a spacing of no. more than 1 per 350 m2. The 24Vac power supply for the CO sensors shall be mounted in the same panel. The power supply shall be looped across the CO sensors. The proposed CO sensor shall provide a 0-10 VDC signal for measuring the CO level in the car park area. CO monitoring devices shall be mounted remotely throughout the car parks. The devices shall be mounted in accordance with the manufacturers guidelines but no greater than 1.5 m above FFL. CO Sensor shall be suitable for wall mount & capable of following features: (As per 350 sqm covered area) for Basement ventilation. |
| 1023 | Digital display of the CO level : 0 to 200 ppm Analog output : 4 to 20 mA / 0-10VDC Low Voltage operation : 24 VAC / VDC Test Switch : Provides mode for system self test. Automatic Calibration (Field Calibration Kit) Over-range indication. Start-up mode : steps display and output through test ranges. Solid – Stat sensor : Life expectancy of 7 to 10 years. Multiple sensors with one power supply. |
| 1024 | Variable speed drives. Supply of following HVAC dedicated VFDs with IP 55 enclosures with Mains disconnect, complying with the tender specifications and having: 1. built-in dual 5% impedance DC link reactor (harmonic filters) on the positive and negative rails of the DC bus of the VFD. 2. built-in EMC Filters (electromagnetic compatibility filters) for for VFDs for restriction of conducted emissions to comply with IEC61800: 3 (unrestricted distribution):2004 Category C 3, 3. Three-feedback PID controller having capability to simultaneously accept 3 feedback signals from temperature sensors or pressure sensors or CO2 sensors for process optimization and accordingly regulate the speed of the AHUs or pumps. 4. Provision for additional 3 PID controllers to control external devices such as chilled water modulating valve, fresh air damper, etc. thus reducing the number of I/Os in DDC Controllers & improving system reliability. 5. Automatic Energy Optimization / Load dependent flux optimization functionality for maximum energy savings. |
| 1025 | 6. MODBUS RTU as the communication protocol between BMS & VFDs. 7. VFDs not meeting above requirements shall provide external disconnect, external harmonic filters, additional external EMC Filters to comply with IEC61800: 3 (unrestricted distribution):2004 Category C 1 (50 m), external PLCs / DDCs to achieve 3 Feedback PID Controller functionality and external devices controlling capabilities. |
| 1026 | Supply , Install, test and commission Variable Speed Drivepackage as described above and in specifications suitable for for 0.55 to 1.5 kW motor rating as per the specifications(3 Phase variable frequency output forExh. Fan, . These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item. |
| 1027 | Supply , Install, test and commission Variable Speed Drivepackage as described above and in specifications suitable for for 7.5 -9.3kW motor rating as per the specifications(3 Phase variable frequency output for Normal Exh. Fans. These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item. |
| 1028 | Supply , Install, test and commission Variable Speed Drivepackage as described above and in specifications suitable for for 2.2-3.7 kW motor rating as per the specifications(3 Phase variable frequency output for Normal Exh. Fans , . These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item. |
| 1029 | Supply , Install, test and commission Variable Speed Drivepackage as described above and in specifications suitable for for 5.5 kW motor rating as per the specifications(3 Phase variable frequency output for exh. fan , . These variable speed drives shall get the input from the remote air differential pressure adjuster , as described above in item. |
| 1030 | Air Purifier (Bio-Polar based ) Supply, Installation, Testing and commissioning of comprehensive Air Purification system in the specified areas whereAHU/ Cassette /Hi-wall / Ductable units etcare installed , so as to improve Indoor air quality by usingNeedlepointBi-polar Ionization technology, whichproduces a natural Bio Climate rich in positive and negativeions.The Needle Point Bipolar Ionizers should not have any consumables and should have a life of10 years.System should be fitted with Fine Filter Media with very less static drop acceptable upto 5 mmwg of Initial pressure drop wherever requires.Along with indoor Air quality monitor tomeasure Air quality parameters including PM2.5, TVOC, CO2, Humidity and Temperature. This monitor should be a 3 tier architecture including sensor Hardware, secure cloud infrastructure, monitoring apps including dashboard, android/IOS apps, where ever requires Project design should meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System should kill microorganism and pathogens, remove Odour, VOC and reduce dust particle /particulate matter / PM2.5 /PM 10. The product should be UL / Intertek listed. Product should have minimal or negligible pressure drop & low power consumptions. Product should have UL 867 and UL 2998 certification (for zero ozone emission). |
| 1031 | The Product shall have been Tested on COVID-19 Surrogate for its efficacy. The System should be capable of providing periodic Prventive maintenance for automated after sales support service in form of notification/alerts and user interaction through dashboard application |
| 1032 | Up to 4000 CFM, 21 Watt |
| 1033 | 4500 to 7000 CFM, 36 Watt |
| 1034 | 7500 to 13500 CFM, 48 Watt |
| 1035 | 300 to 2800 CFM, For IDU Duct Mount |
| 1036 | AIR CURTAIN Supply,installation testing and commissioning of AIR CURTAIN of following size as per approved make and with Door limit switch/sensor with multi speed regulator .(At ground entrance) |
| 1037 | 1500 mm long (High flow type) |
| 1038 | 1800 mm long (High flow type) |
| 1039 | 2100 mm long (High flow type) |
| 1040 | CONDENSATE DRAIN PIPE Supplying, fixing,testing and commissioning offollowing PVC pipes for condensate drain duly insulated with kinny foam & vapour barrier duly secured with adhesive tape as per specification ,cut to required length and installed with all joints , including the necessary fittings. (For all the AHU/FCU units upto the main header in the shaft dor vertical risers) |
| 1041 | 50mm dia |
| 1042 | 40mm dia |
| 1043 | 30mm dia |
| 1044 | 25 mm dia |
| 1045 | Refrigerant-410a Supply , charging & Leackage testing of refrigerant -410a in additionalcopper piping circuit. |
| 1046 | AIR SIDE WORKS Site Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of fabricated at site GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, supports etc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces. |
| 1047 | Spcl. Note: All Duct Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes andHangers, Supports and Modular system – Wire rope Supports(double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications |
| 1048 | 0.63mm (24 gauge) GSS |
| 1049 | 0.8 mm (22 gauge)GSS |
| 1050 | 1.0mm(20 gauge)GSS |
| 1051 | 1.25mm(18 gauge)GSS |
| 1052 | Factory Fabricated Duct - GI duct Supply,Installation,balancing and commissioning of factory fabricated GSS sheet metal ducts (rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter,vanes, hangers, supportsetc.) in accordance with the approved shop drawings and specifications , and shall also confirm to the BIS specifications.The duct shall be fabricated at site for to suit pieces. |
| 1053 | Spcl. Note: All Duct Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes andHangers, Supports and Modular system – Wire rope Supports(double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications |
| 1054 | 0.63mm (24 gauge) GSS |
| 1055 | 0.8 mm (22 gauge)GSS |
| 1056 | 1.0mm(20 gauge)GSS |
| 1057 | 1.25mm(18 gauge)GSS |
| 1058 | Supply, Fabrication, Installation and testing of Insulated Al. Flexible ducts in accordance with the approved shop floor drawings and specifications and shall also confirm to the BIS specifications. |
| 1059 | 150 mm Dia. |
| 1060 | Grilles/Diffusers Supplying and fixing of Extruded aluminium supply and return air grilles/diffusers/louvres with dampers, supply air plenum etc. duly powder coated as per specifications and drawings. |
| 1061 | Aluminium supply air grilles with damper. |
| 1062 | Aluminium return air grilles without damper. |
| 1063 | Aluminium supply air square diffuser with damper |
| 1064 | Aluminium return/exhaust air square diffuser without damper. |
| 1065 | Aluminium return/exhaust airValve circular/squirell diffuser without damper. |
| 1066 | Linear air grilles (150 MM wide) |
| 1067 | Aluminium supply air collar damper |
| 1068 | AI Volume control dampers for ducts |
| 1069 | Fresh Air/Exhaust Air Louvers Supplying and fixing ofextruded aluminium louvres with frame bird screeen , mounting arrangement etc. as per specifications and drawings. Fresh Air/Exhaust Louvers |
| 1070 | MOTORIZED FIRE AND SMOKE DAMPERS Supplying, fixing, Testing and commissioning of fire dampers in suppy air duct/main branch andreturn air path as and where required of required size i/c control wiring ,the damper shall be motorized combination fire and smoke damper (spring return type) of approved make of atleast 120 minute fire rating and as per the specifications as detailed earlier in the relevant sections.The fire damper shall be complete with electronic temperature sensor and electrically operated actuator .The fire dampers shall be located in the supply/return air ducts, at all fire rated crossovers (shafts/walls etc.) The control panel will be such located that the reset can be easily done These combination smoke and fire dampers shall be interlocked with the building management system for fire detection / HVAC and shall trip/close in the event of fire / smoke in the respective zone . |
| 1071 | Bare Fire Dampers with 400 mm sleeve |
| 1072 | Control panel actuator , including Electrical,spring type actuator,remote indication of the fire damper position. |
| 1073 | Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers. |
| 1074 | Sealing the openings around the sleeve of thefire dampers with approved fire sealant, as per the recommendations of the manufacturer and specifications. |
| 1075 | Supply and Installation of Fire Resistant Fabric Flexible Connection to be installed between all the Fans,AHU/Indoor Units, AHU and the ducting to provide flexibility of movement in case of a seismic event and to prevent transmission of vibration from the unit to the duct. The fabric should be fire resistant, fiberglass weave with silicone rubber coating with Galvanized metal strip as per specifications. Flexible duct connector fabric shall be air tight, waterproof, virtually chemically inert and shall not emit toxic fumes when exposed to open flame.. The flexible canvas connectorshall be tested and certified in accordance with BS 476 Part 7 Class 1 and NFPA 701 from NABL accredited laboratory. |
| 1076 | Supply and Applicationoffire retardant Coating CISBOND FR 802 having fire rating for 2 Hours at 250°C Conforms BS 476 Part 6 & 7 Warrington Fire UK, pull of adhesion as per ASTM D4541, Impact resistance as per ASTM 2794in accordance with Building Regulations onkitchen ventilation ducts & smoke extract ducts & all the joints must be filled with the acrylic water base fire retardant sealant for duct joints CISCRYL DS 50as per the specifications. |
| 1077 | MECHANICAL INSULATION DUCT LINE ACOUSTIC TREATMENT Supply and installation of cross linked open cell Oxide Acetate( AccoIsolate) Foam/Nitrile Rubber Acoustic insulation on ducts having density of 30 to 60Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of-70°C to +100°C and fire rating Class O as per BS 476 Part 6 fromCBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 andas per the approved specifications. 15mm thickAcoustic open cell insulation on one side for Duct acoustic insulation |
| 1078 | DUCT LINE THERMAL INSULATION Supply and installation of cross linked closed cell Oxide Acetate( Thermo Isolate) Foam/Nitrile RubberThermal insulation on ducts having density 0f 30 ±3Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of-70°C to +100°C and fire rating Class O as per BS 476 Part 6 fromCBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 andas per the approved specifications. |
| 1079 | 25 mm thick insulation with Two layer 7 mile cloths with adhesive onsupply/Return/Exh.air duct on exposed area |
| 1080 | 13 mm thick insulation |
| 1081 | 9mm thick insulation |
| 1082 | Supply and installation of cross linked closed cell Oxide Acetate( Thermo Isolate) Foam/Nitrile RubberThermal insulation on ducts having density 0f 30 ±3Kg/ M³ ,having K value 0.029 W/m ° K at 0°C Deg temp and temp range of-70°C to +100°C and fire rating Class O as per BS 476 Part 6 fromCBRI,Roorkee and CFC/HCFC free as per US EPA 5021 A(2014 ). • Smoke & Toxicity index of material shall be passed as per IMO MSC 307 ( 88 ) 2010 Anexx 1 Pt 2 andas per the approved specifications. 19mmthick oxide acetate insulation for underceck plain |
| 1083 | Therates for the distribution boards from the Breakers and instrumentsshall also include the following : Wiring forlight / Fan points with 1.5 sq. mm PVC insulatedcopper conductor1100 Volt grade strandedflexible FRLS wiresofapproved makein1.6mmthick25mmdiaMS conduitincluding costof providing & fixing saddles, hangers, supports, cutting chases and filling chases for recessed conduiting, and including the cost of providing and fixing a6 amp240Volt ModularPlatetypeswitchesof approved quality,colour, makeanddesign with mouldedcover platein zinc chromate passivated MS box and including the cost of running 1.5 sq. mm PVC insulated copper earth wire for loop earthing etc. complete |
| 1084 | TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link. |
| 1085 | All MCB’s shall be of minimum 10 KA breaking capacity and MCCB "s shall be not lessthan 25KA |
| 1086 | The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermalmagnetic microprocessorreleasesas per BOQ and following : i.MCCB rating upto 250 Amps with thermal magnetic releases. ii. MCCB above 250 Amps with microprocessor releases. |
| 1087 | All MCB’s used for protection ofresistiveand lightlyinductive loadshallbetype “B”characteristic and inductive(motor)load shall be of type “C” characteristic. |
| 1088 | Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. i.IP 42 for indoor panels. ii. IP 55 for ODU panel. |
| 1089 | AllMCCB’sshall beprovidedwithoperatingmechanismfordoor interlock. |
| 1090 | All hinged door shall be earthedthrough2.5 sq mm tinnedbraided copper wire. |
| 1091 | Providing cableclamps/ supportswithin distributionboardscable alley. |
| 1092 | Current density of aluminium shall be 1sq mm for 1.0 Amps for rated current of bus bars. |
| 1093 | Model, current capacity location and frame size of switchgear shall be writteninside of thepanel doors with paint / permanent marker as approved shop drawings / site requirment. |
| 1094 | All meter shall be digital type and all starter shall be as per Type-2 Coordination chart |
| 1095 | Current Transfomer shall be resin cast. |
| 1096 | All Panel Shall be BMS Compitable |
| 1097 | Spcl. Note: All Panels, Cable tray,Power Cable etc.Supprots incl. Supply, Fabrication, installation and testing of Steel Wire Ropes andHangers, Supports and Modular system – Wire rope Supports(double channel wedge lock, unlocking device should not be integral part of grip for added safety) complete with end fixing. Wire Hangers shall be independently tested by reputed third party testing organization to sustain safe working load for 120min at elevated temperature of 175 deg. C or above. System shall be in accordance with the approved shop drawings and as required by the specifications |
| 1098 | Floor Mounted Panels with base frame (Min. 75 mm ) |
| 1099 | Plant/AHU/Fan Panel Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of following LT panels fabricated out of 14 guage CRCA sheet steel in cubical formationwith reinforecment of suitable size angle iron and channel T iron flats. All steel material used in the construction of panels shall be powder coated. A solid busbar shall be provided at the bottom of the panel with two connecting eyes for termination. The boards shall be suitable for 415 volts, 50 Hz, 3 phase , 4 wire supply system. All the hardware used in the fabrication of the panel shall be galvanized with zinc passivation. The panel shall be compartmentalized to accommodate one feeder in each compartment. A vertcal cable alley of suitable width shall be provided to serve on or two vertical feeder sections. Also the opening between the busbar chamber and the feeder section shall be shrouded with bakelite / hylam sheet with min.3 mm thickness. |
| 1100 | The panel drawing shall be approved before taking up the fabrication and compitable BMS if in future required. |
| 1101 | In All panel Each starter should have remote control and interlocking facilities including auto manual switch, NO/NC contacts for control and must have auto manual operation suitable to take signal from fire alarm panel for automatic operation of fan in case of fire.All smoke /vent. fan panel the starters shall have suitable facility to operate with fire sensing control modules. Ventilation & Smoke Fan Panel |
| 1102 | HVAC Fan Panel MCC-01 to 08,11,12 (Base-03,02,01) |
| 1103 | Incoming |
| 1104 | 1 no. 63 amp MCCB |
| 1105 | Phase indicating lights with control fuses. |
| 1106 | Breaker ON/OFF/TRIP indicating lights. |
| 1107 | Bus Bars |
| 1108 | 100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1109 | Outgoings |
| 1110 | 1 nos. 13-18 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1111 | 1 nos. 13-18 A,TP MPCB (with DOL starter ) |
| 1112 | Panel as described above and in drawings. |
| 1113 | HVAC Fan Panel MCC-09 (Base-02) |
| 1114 | Incoming |
| 1115 | 1 no. 50 amp MCB |
| 1116 | Phase indicating lights with control fuses. |
| 1117 | Breaker ON/OFF/TRIP indicating lights. |
| 1118 | Bus Bars |
| 1119 | 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1120 | Outgoings |
| 1121 | 2 nos. 2.5-4 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1122 | 2 nos. 4-6.3 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1123 | Panel as described above and in drawings. |
| 1124 | HVAC Fan Panel MCC-10 (Base-01) |
| 1125 | Incoming/Outgoing |
| 1126 | 1 nos. 4-6.3A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1127 | Phase indicating lights with control fuses. |
| 1128 | Breaker ON/OFF/TRIP indicating lights. |
| 1129 | Panel as described above and in drawings. |
| 1130 | HVAC Fan Panel MCC-13 (Base-01) |
| 1131 | 1 no. 125 amp MCCB |
| 1132 | Phase indicating lights with control fuses. |
| 1133 | Breaker ON/OFF/TRIP indicating lights. |
| 1134 | Bus Bars |
| 1135 | 160 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1136 | Outgoings |
| 1137 | 1 nos. 2.5-4A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1138 | 2 nos. 13-18A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1139 | 2 nos. 20-25A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1140 | Panel as described above and in drawings. |
| 1141 | HVAC Fan Panel MCC-14 (GF) |
| 1142 | Incoming/Outgoing |
| 1143 | 1 nos. 13-18 A,TP MPCB (with DOL Starter ) |
| 1144 | Phase indicating lights with control fuses. |
| 1145 | Breaker ON/OFF/TRIP indicating lights. |
| 1146 | Panel as described above and in drawings. |
| 1147 | HVAC Fan Panel MCC-15,16,17 (GF,1st) |
| 1148 | Incoming/Outgoing |
| 1149 | 1 nos. 2.5-4 A,TP MPCB (with DOL starter ) |
| 1150 | Phase indicating lights with control fuses. |
| 1151 | Breaker ON/OFF/TRIP indicating lights. |
| 1152 | Panel as described above and in drawings. |
| 1153 | HVAC Fan Panel MCC-18 (GF) |
| 1154 | Incoming/Outgoing |
| 1155 | 1 nos. 4-6.3 A,TP MPCB (with DOL starter ) |
| 1156 | Phase indicating lights with control fuses. |
| 1157 | Breaker ON/OFF/TRIP indicating lights. |
| 1158 | Panel as described above and in drawings. |
| 1159 | HVAC Fan Panel MCC-19 (6th) |
| 1160 | Incoming/Outgoing |
| 1161 | 1 nos. 9-14 A,TP MPCB (with DOL starter ) |
| 1162 | Phase indicating lights with control fuses. |
| 1163 | Breaker ON/OFF/TRIP indicating lights. |
| 1164 | Panel as described above and in drawings. |
| 1165 | HVAC Fan Panel MCC-20 (GF) |
| 1166 | Incoming |
| 1167 | 1 no. 32 amp MCB |
| 1168 | Phase indicating lights with control fuses. |
| 1169 | Bus Bars |
| 1170 | 50 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1171 | Outgoings |
| 1172 | 1 nos. 2.5-4 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1173 | 1 nos. 6-10 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1174 | Panel as described above and in drawings. |
| 1175 | HVAC Fan Panel MCC-21 (2nd) |
| 1176 | Incoming |
| 1177 | 1 no. 20 amp MCB |
| 1178 | Phase indicating lights with control fuses. |
| 1179 | Bus Bars |
| 1180 | 32 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1181 | Outgoings |
| 1182 | 1 nos. 2.5-4 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1183 | 1 nos. 4-6.3 A,TP MPCB (with VSD Space provision in panel , VSD item separate in boq)) |
| 1184 | Panel as described above and in drawings. |
| 1185 | HVAC Fan Panel MCC-22,23(Terrace) |
| 1186 | Incoming |
| 1187 | 1 no. 125 amp MCCB |
| 1188 | Phase indicating lights with control fuses. |
| 1189 | Breaker ON/OFF/TRIP indicating lights. |
| 1190 | Bus Bars |
| 1191 | 160 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1192 | Outgoings |
| 1193 | 1 nos. 9-14 A,TP MPCB (with DOL starter ) |
| 1194 | 3 nos. 6-10 A,TP MPCB (with DOL starter ) |
| 1195 | 2 nos. 13-18 A,TP MPCB (with DOL starter ) |
| 1196 | Panel as described above and in drawings. |
| 1197 | HVAC Fan Panel MCC-24 (Terrace) |
| 1198 | Incoming |
| 1199 | 1 no. 160 amp MCCB |
| 1200 | Phase indicating lights with control fuses. |
| 1201 | Breaker ON/OFF/TRIP indicating lights. |
| 1202 | Bus Bars |
| 1203 | 200 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1204 | Outgoings |
| 1205 | 7 nos. 6-10 A,TP MPCB (with DOL starter ) |
| 1206 | 2 nos. 13-18 A,TP MPCB (with DOL starter ) |
| 1207 | Panel as described above and in drawings. |
| 1208 | HVAC Fan Panel MCC-25 (Terrace) |
| 1209 | Incoming |
| 1210 | 1 no. 80 amp MCCB |
| 1211 | Phase indicating lights with control fuses. |
| 1212 | Breaker ON/OFF/TRIP indicating lights. |
| 1213 | Bus Bars |
| 1214 | 100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1215 | Outgoings |
| 1216 | 4 nos. 6-10 A,TP MPCB (with DOL starter ) |
| 1217 | Panel as described above and in drawings. |
| 1218 | Air-conditioning AHU Fan Panel |
| 1219 | HVAC AHU Panel MCC-01 (VIP 1st) |
| 1220 | Incoming |
| 1221 | 1 no. 63 amp MCCB |
| 1222 | Phase indicating lights with control fuses. |
| 1223 | Breaker ON/OFF/TRIP indicating lights. |
| 1224 | Bus Bars |
| 1225 | 80 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1226 | Outgoings |
| 1227 | 1 nos. 9-14 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan ) |
| 1228 | 1 nos. 6-10 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan ) |
| 1229 | Panel as described above and in drawings. |
| 1230 | HVAC AHU Panel MCC-2 (VIP Terrace) |
| 1231 | Incoming |
| 1232 | 1 no. 80 amp MCCB |
| 1233 | Phase indicating lights with control fuses. |
| 1234 | Breaker ON/OFF/TRIP indicating lights. |
| 1235 | Bus Bars |
| 1236 | 100 amp TPN Aluminum Bus Bar with heat shrinkable insulation colored sleeves. |
| 1237 | Outgoings |
| 1238 | 1 nos. 20-25 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan ) |
| 1239 | 1 nos. 6-10 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan ) |
| 1240 | 1 nos. 4-6.3 A,TP MPCB (To AHU Blower VSD, VSD With AHU or AHU with VFD Plug fan ) |
| 1241 | 1 nos. 6 A, MCB |
| 1242 | Panel as described above and in drawings. |
| 1243 | CABLING (POWER ) Power Cabling and Earthing: Spcl. All Cables Should be fire survival Cables Supply, installation, testing & commisioning of Aluminum conductor cables PVC sheathed, armoured cables of 1.1 KV grade with termination glands , identification tags, clamps and saddles etc. |
| 1244 | 3Cx10 Sqmm |
| 1245 | 4Cx 10 Sqmm Cu |
| 1246 | 3Cx 06 Sqmm |
| 1247 | 3Cx04 Sqmm |
| 1248 | 2Cx04 Sqmm (Cu Conductor) |
| 1249 | 4Cx 06 Sqmm Cu |
| 1250 | Control Cabling Supply, installation, testing & commisioning ofCopper conductor , PVC insulated, PVC sheathed armoured cable of 1.1 KV grade (Which is Interconnecting wiring for the fire alarm system with the AHU and the smoke dampers and AHU toPanel). |
| 1251 | 8C x 1.5 Sqmm |
| 1252 | 2C x 1.5 Sqmm Cu Cable (control cum transmission wiring in medium duty PVC Conduit between indoor and outdoor units.) |
| 1253 | 2C x .5 Sqmm |
| 1254 | Supplying and makingoutdoor end termination of cable termination of above cables with Al./copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required. |
| 1255 | 3Cx10 Sqmm |
| 1256 | 4Cx 10 Sqmm Cu |
| 1257 | 3Cx 06 Sqmm |
| 1258 | 3Cx04 Sqmm |
| 1259 | 2Cx04 Sqmm (Cu Conductor) |
| 1260 | 4Cx 06 Sqmm |
| 1261 | Supplying and installing following size of perforated Hot dipped G.I. cable trays, G.I. bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with suitable suspendersabove in general points complete as required. |
| 1262 | 100 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 1263 | 150 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 1264 | 225 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 1265 | 300 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 1266 | 450 mm. Width x 50mm. Depth x 1.6mm. Thickness. |
| 1267 | Supplying and Laying following size of G.I. wire on surface or in recess for loop earthing alongwith the existing surface/ recessed conduit/ submain wiring / on cable tray/ on surface including G.I. clamps etc. complete as required. |
| 1268 | 6 SWG G.I. wire |
| 1269 | Supply, installation, testing & commissioning of 1/2.7" 5MP (2592×1944) progressive scan imager,2.8 – 12 mm MFZ lens,Min. Illumination 0.008 Lux @ F1.2, AGC ON; 0.01 Lux @ F1.6, AGC ON; 0 lux with IR,Max. Frame Rate 30fps @ all resolution, 60fps @ 1080P,TWDR -120db ,Low light performance (0.035 lux in color mode),50 m IR distance, Audio Communication Bi-directional audio (2-way) ,Image Features Defog, BLC, HLC, 2D/3D DNR,Alarm IN x 1, Alarm OUT x 1,Intelligent Video Analytics-Line crossing, regionEntering/Exiting/Intrusion (human,motor vehicle/ non-motorvehicle classification),Line crossing human/ motor vehicle/non-motor vehicle counting, Scene change, video blur and video color cast detection, ONVIF Profile (S, G & T),Image Features Defog, BLC, HLC, 2D/3D DNR,Corridor Pattern,Emissions- Certifications: ONVIF Profile S compliant, UL, CE, EN, FCC, NDAA & RoHS compliant etc complete as reqd. |
| 1270 | Supply, installation, testing & commissioning of 1/2.7" 5MP (2592×1944) progressive scan imager,2.8 – 12 mm MFZ lens,Min. Illumination 0.008 Lux @ F1.2, AGC ON; 0.01 Lux @ F1.6, AGC ON; 0 lux with IR,Max. Frame Rate 30fps @ all resolution, 60fps @ 1080P,TWDR -120db ,Low light performance (0.035 lux in color mode),70 m IR distance, Audio Communication Bi-directional audio (2-way) ,Image Features Defog, BLC, HLC, 2D/3D DNR,Alarm IN x 1, Alarm OUT x 1,Intelligent Video Analytics-Line crossing, regionEntering/Exiting/Intrusion (human,motor vehicle/ non-motorvehicle classification),Line crossing human/ motor vehicle/non-motor vehicle counting, Scene change, video blur and video color cast detection, ONVIF Profile (S, G & T),Image Features Defog, BLC, HLC, 2D/3D DNR,Corridor Pattern,Emissions- Certifications: ONVIF Profile S compliant, UL, CE, EN, FCC, NDAA & RoHS compliant etc complete as reqd. |
| 1271 | Supply, installation, testing & commissioning of 1/2.7" 5MP (2592×1944) progressive scan imager,2.8 – 12 mm MFZ lens,Min. Illumination 0.008 Lux @ F1.2, AGC ON; 0.01 Lux @ F1.6, AGC ON; 0 lux with IR,Max. Frame Rate 30fps @ all resolution, 60fps @ 1080P,TWDR -120db ,Low light performance (0.035 lux in color mode),70 m IR distance, Audio Communication Bi-directional audio (2-way) ,Image Features Defog, BLC, HLC, 2D/3D DNR,Alarm IN x 1, Alarm OUT x 1,Intelligent Video Analytics-Line crossing, regionEntering/Exiting/Intrusion (human,motor vehicle/ non-motorvehicle classification),Line crossing human/ motor vehicle/non-motor vehicle counting, Scene change, video blur and video color cast detection, ONVIF Profile (S, G & T),Image Features Defog, BLC, HLC, 2D/3D DNR,Corridor Pattern,Emissions- Certifications: ONVIF Profile S compliant, UL, CE, EN, FCC, NDAA & RoHS compliant etc complete as reqd. |
| 1272 | Dome camera 4 MP - Supply, Installation, Testing & Commissioning of IP Network TDN Low-Light IR Dome Camera, 1/2.8" CMOS, 4 MP @ 25fps & live Viewing. Triple stream, Min. Illumination required 0.03 lux (color), DWDR, 2.8 - 12 mm @ F1.4, manual varifocal zoom lens, Backlight Compensation, 3DNR, Privacy Mask, Internal/External Smart IR LEDs with upto 50m IR distance, Inbuilt Mic, Built-in micro SD card slot, up to 128GB, H.265,H.264/MJPEG,IP 67 & IK10, PoE Class 0/12V DC/24VAC, Die-Cast Aluminum Construction,Having Operating temp range : -30°C to 60° C. Certifications: ONVIF Profile S & Profile G compliant,Object removal (object left/missing detection), scene change and video blur detection, intrusion and line crossing, Emissions- FCC Part 15.107 Class A, FCC Part 15.109 Class A , EN 55032, EN 55035 (IEC 61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC 61000-4-6, IEC 61000-4-8) .Immunity EN 55030-4.Safety UL 62368-1, IEC 62368-1 EN 62368-1, CAN/CSA C22.2 No. 62368-1-14, J62368-1, AS/NZA 62368.1.Environment -RoHS (IEC 62321-3-1, IEC 62321-5, IEC 62321-4, IEC 62321-6, IEC 62321-7, IEC 62321-7-2,IEC 62321-8), WEEE, REACH,NDAA. |
| 1273 | Supply, Installation, Testing & Commissioning of IP Network 2MP, 30X IP IR PTZ Camera, 1/2.8" CMOS, 2MP @ 60FPS, H.265, H.264, , 120dB True WDR,90dB TrueWDR HLC, BLC, triple stream, Lens wide 4 to 5mm - Tele 120 to 150mm, 30X motorized focus & zoom lens, Inbuilt/Externla IR uo to 150 Meters, Built in Video Analytics such as Video Motion Detection, 3DNR, Stream encryption, Privacy Zones 8 ,Shutter Speed (Auto) 1/30(25) - 1/30,000 sec, Pan Speed: 0.1°/s ~ 240°/s PAN Range 360° Endless, Tilt Speed: 0.1° ~ 160°/s , IR PTZ: +15° ~ -90°, Presets 96, Dual channel Audio G.711/G726, SDXC up to 512GB, Alarm Input/Output 2/2, High-PoE (UPOE) and 24VAC, IP 66, IK 10 vandal proof, Inbuilt Heater, Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S compliant, UL, CE, EN, FCC, NDAA & RoHS compliant etc complete as reqd. |
| 1274 | ANPR cameras:Supply , Installation , Testing and Commissioning of 4Mpx Bullet, 1080P @ 60fps, 1/2.8", P-IRIS Sensor, Autofocus Motorized remote zoom lens 2.8-12mm or 5-50mm Manual varifocla lens as per site, f1.5, H.265, H.265 compression,Smart Codec, internal/external 50mtr Adaptive IR, 120dB true WDR, Minimum Illuminator @F1.4 0.008lux color; 0.0018lux Mono, 3D noise filtering, Bi directional Full Duplex Audio, 1 Alarm In, 1 Alarm out, 3 independant stream, Diagonal:46.5° ~ 18.8°,Horizontal :36.5° ~ 15,Vertical 27° ~ 11.3° , Camera should having SD card provision of 128 GB,Contruction:Aluminium, Stopped Vehicle, Object Counting, Camera Should also supports DNN Analytics, TCP/IP, UDP/IP (Unicast, Multicast IGMP), The Camera to be provided by OEM should not be complying to GB28181, GB/T28181-2011 standards and there should be no option to activate or deactivate GB/T 28181 standards in the camera web page/Settings. |
| 1275 | ANPR Base Software & Server |
| 1276 | ANPR Camera License |
| 1277 | Supplying of 4 U Rack mount single chassis Network Video Recorderwith dualGbNIC,, max 2 simultaneous monitors, RS-232/485 serial port,NVR should support up toconnect min 128cameras per appliances , It must continuously record up to 800 Mbps (Windows) 1200 Mbps (Linux)of video for high concentration of high definition IP cameras Local client display rate: Windows OS: up to 700 frames per second Linux OS: up to 900 frames per second It should support streaming live/recorded video up to 500 simultaneous PC clients, NVR should Two way audio feature Processor: Gen 4 Intel® Xeon E3 ,It must work on Windows,Linux platform with 2x1 Gbps NIC and 16 GB of RAM and 8 USB slot (It should be configured as per the storage calculation provided by VMS OEM) ,It must support DVI-I, HDMI, 1 display ports, max 2 simultaneous monitors ,NVR should support Maximum 20 HDD with 12 HDD per slot and It should support minimum 240 TB of storage with RAID 6 . Windows, operating system shall boot and run on a solid-state drive (SSD) to ensure high performance and reliability RAID one is also on Operating system. NVR shall have 2 Gigabit |
| 1278 | 1000Base-T RJ-45 NIC card NVR shall have RS-485 serial port capabilities to communicate with serial devices Requirement is of critical nature and hence offered NVR must be of global standards and hence should be CE, FCC and UL certified. It should support8/4 Alarm Inputs/Output NVR shall have Dual Hot Swap redundant Power Supplies Operating Temperature 40° - 95°F (4.5° - 35°C) Pre-loaded Operating System must be on windows platform, NVR should support N+1 feature as well. (3 Main + 1 redundant Make-Tyco/Mobotix/Avigilon |
| 1279 | Supply, Installation, Testing & Commissioning of The VMS software shall have an open architecture supporting IP cameras and encoders from multiple manufacturers, entry-level features to high-resolution, megapixel features, visual indication alerting operators of video loss, client software shall operate on all of the following operating systems: Windows, Linux, Mac OSX, run multiple client applications simultaneously on one workstation with multiple monitors. Up to 12 monitors shall be configured on a single workstation, retrieve video, audio and alarm data and provide it to the VMS clients, VMS software shall provide a purpose built mobile application capable of viewing multiple simultaneous live video streams and playing a recorded video stream (Android, iOS, Windows), VMS shall be able to use the Active Directory or LDAP features, VMS shall allow maps to be embedded inside of maps (i.e. hierarchical or nested maps). When an event happens on a map that is embedded inside of a map, VMS allows soft triggers to be placed, viewed and triggered from a map, VMS shall allow for the configuration local drives, direct attached storage drives and iSCSI drives, VMS standalone player shall package all of the exported video has not been tampered with using a keyed Hash |
| 1280 | Message Authentication Code (HMAC), VMS software shall be used to connect different types of events, such as input triggers and recognize the following event types: Video Motion, Video Loss, Input Trigger, Health, IP Camera Connection, Software Trigger and Analytics ,Client application shall be able to use OpenGL and Direct 3D to decompress and render video, Camera preview Style e.g Hovering, VMS has Video Push feature to another Client desktop simultaneously, Suspect Tracking :Configure camera links between cameras to follow a suspect between different camera scenes, Inactivity timeout : Save bandwidth with blacked out video panels after inactivity, VMS shall be supplied with minimum 100 nos of thick clients and 16 mobile clients, Data backfilling from primary server to failover over server in the primary server failure situation. |
| 1281 | Supply , Installation , Testing and Commissioning of Enterprise Grade HDD with min 7200 RPM , 12 TB Each |
| 1282 | Supply , Installation , Testing and Commissioning of Joystick controller |
| 1283 | Supply , Installation , Testing and Commissioning of 43" LED 24x7 operational displays |
| 1284 | Supply , Installation , Testing and Commissioning of workstation ( I7 PC, with 8 GB RAM and 1 TB HDD, 100/1000 Mbps Ethernet card, USB connection and internal modem, Microsoft(R) Windows(R) 10 OS Professional Enterprise, Web Server Software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and antivirus software with 22" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad.) |
| 1285 | Supply and fixing of following 20mm sizes heavy duty pvc conduit/channel of approved make along with accessories in surface/recess incl. wall cutting and making good the same incase of recessed conduit as required complete in all respects. |
| 1286 | Supply, Installation, Testing & Commissining of 2 Door 2 Reader Access Controller, On-board 10/100 Mbps Ethernet Communicates directly with the central system, Structured database allows storage of large amounts of cardholder records for off-line card validation, Reader communications via standard Wiegand or Mag Stripe interfaces, Eight supervised inputs (four available per door), Two relays (normally opened or closed) and open collector outputs, Self resetting fuses – saves maintenance time, A supervised input can be mapped to a physical out put, Onboard LED - provides visual status, Dedicated tamper input, Database memory 2GB SD Card Cardholders, Storage up to 200,000 cardholders at the door, Transactions Up to 50,000 transactions in offline operation, Controller should be CE, FCC, UL294 Certified, Temperature rating -10º to 55°C (14° to 133°F).Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1287 | Supply, Installation, Testing and Commissioning of future ready MultiClass reader, with support for Bluetooth & Cloud support as per technical specification, the Reader should support both freq 13.56 MHz & 125 kHz, support both ioProx and HID credentials @125khz, MIFARE Plus EV1 and ISO/IEC 14443A and 14443B @ 13.35MHz, Output - RS-485: 1 supervised open-drain, up to 750 mA to connect the Mag lock & magnetic contact if required, should have integrated sounder, should support End to end Encryption, Operating Temperature -40 °C to +70 °C (-40 °F to +158 °F), LED Indicator - Multi-Color bar: Red, Green, Yellow, Blue, Configurable, Flammability Rating UL94 V-2, Ingress Protection Rating IP55, Certifications FCC/IC, CE, UL294, NIST, FIPS 197, RoHS, WEEE. Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1288 | Supply, Installation, Testing and Commissioning of Biometrix Reader, should be UL listed |
| 1289 | SITC of Frictionless Access Control (FRS Reader) AI Based Reader with Less than one second recognition time, Senses liveness to eliminate the risk of spoofing, Access control and video from a single manufacturer to streamline support, Customizable LEDs and builtin speaker provides enhanced user feedback, Cybersecurity protection with no Ethernet at the door, Video Compression H.264 & MJPEG, Max Frame Rate 20 fps, Resolution & Aspect Ratio 1920x1080 (1080p) 16:9 Stereo or 3840x1080, Video Streams Single and Dual Concatenated, Imager Progressive Scan, CMOS, 1/3.2” 13MP (4:3) Image Orientation Settings None, Mirror, Flip, Flip & Mirror Lens Type Fixed, Fixed Iris/Aperture 2.8mm, Focus Control Fixed, Focal Length 2.8mm, Shutter Speed 1/4 - 1/10,000, Lens Aperture F2.8, IR Illumination Yes, IR Distance 2m, IR Filter 850nm, Dynamic Range 69dB, Day/Night Dual Concatenated only, Privacy Zones 3, Face Recognition Through, Face Recognition While, Wearing Mask Yes, with reduced accuracy, Turnstile mode, Audio Bi-Directional Full Duplex, Simultaneous Users 3, Ethernet Interface 10/100/1000Mbps (BaseT), RJ45, Auto-Negotiation Supported Protocols TCP/IP, IPv4, TCP, UDP, HTTP, DHCP, DNS, DDNS, RTP, TLS, RTSP, ICMP, Unicast, NTP, WS- |
| 1290 | Security, CIDS, FSTP, UPnP™, SIP, Wiegand, OSDP, Secure Boot, TLS 1.2 (256-bit cipher minimum); RTSP authentication; role-based access control, Power over Ethernet IEEE 802.3bt Type 3 Class 5, Max draw: 40W, Satellite Camera Module: -4°F to 104°F (-20°C to 40°C), Control Unit: 25°F to 104°F (-20°C to 40°C), 0 to 90% Non-Condensing, Satellite Camera Module: IP40, Control Unit: IP40, Safety EN62368-1, Emissions FCC CFR 47 Part 15 Class A; EN55032 Class A; ICES-003 Immunity EN50130-4; EN 61000-3-2; EN 61000-3-3, Fire Plenium Rating UL-2043; CAN/ULC S142, Environment RoHS; WEEE, Integration with Any thrid Party Access Control System, FRS Camera and Control Unit in metal housing. Require Power via PoE IEEE 802.3bt standard (Max draw 40w), camera 10m Cat6 cable included. |
| 1291 | SITC of AI Based FRS Frictionless License (per device) |
| 1292 | Server - Intel® Xeon® X5650 (2.66GHz/4-core/12MB/95W) Processor /8MB shared L3 cache/8GB PC3-10600R-9(RDIMM)/8SFF HDD Cage/Integrated Dual Port Gigabit Server Adapter/(2) x 460W common slot Power Supply/SATA DVD Optical Kit/3 PCI-E x8 Kit with 6 TB HDD & 21" LED Display. The Server cost should be inclusive of Operating Systems & any other application software |
| 1293 | Supply , Installation , Testing and Commissioning of electromagnetic locks single leaf with LED per specifications |
| 1294 | Supply , Installation , Testing and Commissioning of electromagnetic locks double leaf with LED as per specifications |
| 1295 | Supply , Installation , Testing and Commissioning of touchless push to exit buttons |
| 1296 | Supply of smart cards as per specifications |
| 1297 | Supply , Installation , Testing and Commissioning of emergency door open break glass unit as per specifications |
| 1298 | Supply , Installation , Testing and Commissioning of Magnetic Door Contact |
| 1299 | Supply , Installation , Testing and Commissioning of Buzzer |
| 1300 | Supply , Installation , Testing and Commissioning of walk through door frame metal detectors as per specifications |
| 1301 | Supply , Installation , Testing and Commissioning of panic bar with electric latch retraction. |
| 1302 | Supply, installation of hand held metal detector |
| 1303 | Supply , Installation , Testing and Commissioning of workstation ( I7 PC, with 8 GB RAM and 1 TB HDD, 100/1000 Mbps Ethernet card, USB connection and internal modem, Microsoft(R) Windows(R) 10 OS Professional Enterprise, Web Server Software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and antivirus software with 22" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad.) |
| 1304 | Supply installation, testing & commissioning of Access Control Software along with OEM recomended Server, Highly stable Linux operating system,Windows® based operator workstations,Hot standby/redundant server optional, Seamless integration with external systems; CCTV, Intrusion, Perimeter Detection, Fire and more,Supports third party read heads and multiple card technologies,Supports wireless locks,Virtually unrestrcited system expansion,Sophisticated software modules suite withMulti-language support web-based ,Highly customizable. Should support Occupany control & various Covid related guidelines• A single server should support up to 65,536 master card readers or doors, Resilient and reliable 64-bit Linux-based operating system, Multiple layers of redundancy ,Automated system backups, Configurable data management and archiving ,Web based graphical user interface that ensures no previous Linux knowledge is required. Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1305 | Supply installtion testing commissioining of Visitor Managemnet Software, seamless integrated with the Access Control, should allow Floor/Area wise access to the guest. Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1306 | SITC of Time & Attendance Module with seam less integration with ACS application, should be able to help manage T&A, alsong with Shift Management, Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1307 | Centralized Command & Control application which can show the MAP based layout for highlighting all alarms coming from Access Control, CCTV, Fire Alarm, BMS, IP telephony, Perimeter control, Intrusion Alarm on one single platform. Should have opne supprted platform to integrate mulitple 3rd party system using Backnet / OPC or API based system. Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1308 | SITC of Integrated module for Car Park Management with option to show available parking slots & stop entry of cars if Parking space is full. Make- Tyco,Bosch,Morpho (Controllers, readers & Software should be of same make) |
| 1309 | Supply , Installation , Testing and Commissioning of 8c x 22AWG unarmored AB CopperCable,PVC insulated, shielded PVC 7/38, 8 Core Shielded Cable |
| 1310 | Supply, laying, termination, testing and commissioning of 2 core 1.5 sq.mm power cable. |
| 1311 | Supply , Installation , Testing and Commissioning of 25mm PVC conduit. |
| 1312 | Supply , Installation , Testing and Commissioning of Junction Box 450X600X150 with back Plate |
| 1313 | Supply , Installation , Testing and Commissioning of L2 Switch 12port |
| 1314 | Supply, Installation, testing & Commissioning of Boom Barrier boom length 4 mtrs Type, Brushless Motor with Hydraulic Power supply voltage Switching: 100 ÷ 240V~ 50/60 Hz Motor Brushless 36V Motor rotation speed 1000 ÷ 6000 rpm Max. power 240 W, Motor-pump unit capacity 3.2 lpm,Material type Steel Type of treatment 100 micron protective primer + polyester painting or stainless steel cabinet, Encoder Magnetic absolute encoder Type of deceleration Electronic - via encoder, Type of beam Round Operating ambient temperature -20°C ÷ +55°C, Protection class IP56 (TÜV certified), Weight 85 Kg (65 Kg pillar + 20 Kg cabinet), Type of oil FAAC HP OIL, Dimensions (LxDxH) 469 x 279 x 1100 mm Beam max length 2 ÷ 8 m, Opening time 1,5 s (90° - 2m) - 6 s (90° - 8m), Use frequency 100%, Electronic equipment E680 2 Channel Loop Detector, Including Push Button, Pair of Photocell, Remote. |
| 1315 | Supply, installation, testing and commissioning of K-4 Crash Rated Automatic HydraulicBollard with independent drive unit , As per tender specificationsDrive Hydraulic Actuator Cylinder stroke min 1000 mm Cylinder diameter min 355 mm Cylinder material standard version Steel S355JR EN10210 (16 mm thickness) Rise time About 6 sec/standard version - About 1.5 sec/EFO version Descent time About 2 sec, Hydraulic pump power supply 230 Vac +6% - 10%; 50/60 Hz, Power consumption 1200 W Maximum expressed force 5000 N, Impact resistance 150 Kjoules, Break-in resistance 656 KJoules (in compliance with Standards ASTM F2656-07 - M30), Load class C25 (25t), Junction box protection rating IP 66, Standard refracting strip Height 55 mm Total weight 490 kg (bollard) + 250 kg (pit), Operating temperature -15 °C / +55 °C, Operating temperature with heater (opt.) -40 °C / +55 °C, Pit to be walled in 570x690x1665 mm, Bollard systems should have provision for integration with access control systems. Physical Crash Test K-4 for Single Bollard |
| 1316 | Supply, Installation, Testing & Commissioningof RFID Controller with SMPS & wall mounting cabinet |
| 1317 | Baggage X-Ray Scanner (Medium 550 mm X 350 mm Tunnel Size or Equivalent), 1. Tunnel Sizes :- 530 mm X 320 mm, 530 mm X 350 mm and 550 mm X 350 mm 2. Penetration :- Greater Than or Equal to 10 mm 3. Resolution Wire Detectability :- Standard / Guaranteed :- Greater Than or Equal to 38 AWG Typical :- Greater Than or Equal to 39 AWG. 4. Generator :- Greater Than or Equal to 90 kV 5. Beam Direction :- Vertically Upward / Diagonal / Dual 6. Duty Cycle :- 100% 7. Operating Temperature :- 0 Degree to 50 Degree 8. Operating Humidity :- Up to 95% Non-Condensing 9. Entry and Exit Rollers Tables :- Yes Required in 0.5 meter or 1 meter or 1.5 meter length as per space requirement. 10. Barriers for Rollers :- Yes Required 11. Certifications :- US, CE and AERB (India) 12. Standards Features :-All Required as Stated in the Data Sheets 13. Tropical Kit/Power Conditioner etc. :-Required 14. Mandatory Features Required along with Standard Features :- X-ACT / Screener Assist Threat Detection / Target, Threat Image Projection / HI-TIP, OTP /X-TRAIN, Density Threat Alert (DTA) / High Density Alert (HAD), Advance Image Archiving 100,000 Images |
| 1318 | Supply , Installation , Testing and Commissioning of Guest Room Controller suitable for DIN mounting |
| 1319 | Power Supply for Guest room Controller |
| 1320 | Outdoor Panel with room number, DND- MMR indicator and bell switch, touch panel with back lit conigurable keys |
| 1321 | Glass touch entrance panel with DND-MMR Switch and two other touch switches for Master and bathroom lights |
| 1322 | Glass touch panel with 6 button function, all configurable as per the client, back lit |
| 1323 | Touch Screen - Thermostat |
| 1324 | PIR Sensor for Wash Room Suitable for recessed mounting |
| 1325 | Ultrasonic Sensor for Guest Room |
| 1326 | Magnetic Door Contact suitable for flush mounting for main door and window |
| 1327 | 2 x 1.5 sq.mm Annealed Tinned Copper Shielded armoured cable for signal and power as per specification. (for I/O points hard wired to DDC). |
| 1328 | CAT 6 cable to connect Glass touch panels and other acessories |
| 1329 | Distribution box with required Relays and contactor & power Supply |
| 1330 | Supply , Installation , Testing and Commissioning of Electromechanical swing single door operator in contur design. Operator height of only 70 mm, sharply dropping opening torque during manual access. Reliable function thanks to wind load control with motor-supported closing action as well as TMP and IDC. Modular operator system with upgrade interface – also for retrofitting purposes. Suitable for installation at standard doors and doors with application in emergency exits and escape routes. With the aid of the fire protection upgrade card, also suitable for fire and smoke doors with the corresponding certificate of suitability of the door manufacturer/profile manufacturer. General approval by the local planning and building authorities for application as holdopen device in accordance with the guidelines for hold-open devices and the German industrial standard DIN 14637 andtype approval according to DIN 18650.Should mandatorily inlude Contactless/touchless Wave Switch for making the door touchless, infraredsafety sensors. Door parameters - Door-leaf widths from 700 mmto 1100mm - Max. door-leaf weight of 100 kg & door-leaf width of 1100mm |
| 1331 | Supply , Installation , Testing and Commissioning of Electromechanical swing double door operator in contur design. Operator height of only 70 mm, sharply dropping opening torque during manual access. Reliable function thanks to wind load control with motor-supported closing action as well as TMP and IDC. Modular operator system with upgrade interface – also for retrofitting purposes. Suitable for installation at standard doors and doors with application in emergency exits and escape routes. With the aid of the fire protection upgrade card, also suitable for fire and smoke doors with the corresponding certificate of suitability of the door manufacturer/profile manufacturer. General approval by the local planning and building authorities for application as holdopen device in accordance with the guidelines for hold-open devices and the German industrial standard DIN 14637 and type approval according to DIN 18650. Should mandatorily inlude Contactless/touchless Wave Switch for making the door touchless, infraredsafety sensors. Door parameters - Door-leaf widths from 700mmto 1100mm - Max. door-leaf weight of 100 kg & door-leaf width of 1100mm |
| 1332 | Supply , Installation , Testing and Commissioning of workstation ( I7 PC, with 8 GB RAM and 1 TB HDD, 100/1000 Mbps Ethernet card, USB connection and internal modem, Microsoft(R) Windows(R) 10 OS Professional Enterprise, Web Server Software, DVD-ROM Drive (with RAM), 100/1000 Mbps NIC for Network connection and antivirus software with 22" colour graphics monitor as per Tender Specifications. Accessories included Optical Mouse, Key Pad.) |
| 1333 | AUDIO VIDEO SYSTEM Multi-Purpose Hall at Ground Floor VIP Block Supply, Installation, Testing and Commissioning of projector with 13500 lumens brightness or better at native WUXGA Resolution. The projector shall have typical lifetime of 20,000 hours andcontrast ratio of 2,000,000:1.The projector shall have HDMI x 2,3GSDI x 1 (BNC),DVI-D x 1 HD15 x 1, USB x 1 (type B mini), USB x 1 (type A), WiFi dongle (optional), HDBaseT (RJ45 x 1),RJ45 x 1 signal Inputand 3GSDI x 1 (BNC) , DVI-D x 1 (digital only) signal Output.The projector shall have RS232 In,Control via HDBaseT,Ethernet (10/100) RJ45,Built-in backlit keypad and Wired remote control (3.5mm stereo) - loop out available for daisy chaining. Shall Include Lens as per site requirement complete with standard accessories as required. |
| 1334 | Supply, Installation, Testing and Commissioning of Customized projector Mount Kit for the above projector complete with standard accessories as required. |
| 1335 | Supply, Installation,Testing & Commissioning of 230" diagonal Tab tensioned motorized projection screen with an aspect ratio of 16:10. Screen fabric should in accordance with DIN 4102-1 Class B2 materials. Should equipped with RS 232/485 Relay Connectivity. Screen Should have Anti Heat Cut off Option to avoid any Calamity at site. Heavy Dowel to maintain Flatness. Screen Fabric should meet the requirements of Class B2 of building materials. Should be supplied with complete standard accessories as required. |
| 1336 | Supply, Installation, Testing and Commissioning of 55" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity, HDMI 2.0,DP1.2, HDR10, 300 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1337 | Supply, lnstallatian, Testing & Commissioning of 8x8, 4K60 4:4:4 / HDR 18G HDMI Matrix switcher with audio de-embed, IR, RS232, & TCP/IP control. All HDMI I/O should support full 18G 4K@60Hz 4:4:4 HDCP 2.2 and 4K HDR. Shall support Third party IR, RS232 and IP control. Shall have Manual DIP switch for EDID management. Shall have Analog and digital de-embedded audio outputs for each output. |
| 1338 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1339 | Supply, Installation,Testing & Commissioning ofHDMI & VGA HDBaseT Wall Plate Extension Set with USB. 4K 10.2G 100M 2 HDMI, VGA, & USB2.0 High Speed Wall Plate extender set with audio pass-through / de-embedding and automated display control. Complete set includes Wall plate TX, RX, Power supply, cover plate, Simple programmable display control using CEC or RS232 protocols to power on/off display automatically or by front panel button on wall plate, Support HDMI input video resolutions up to 4K@60HZ 4:2:0 8 bit deep color. Should be HDCP 2.2 Compitable complete with standard as required. |
| 1340 | Supply, lnstallatian, Testing & Commissioning of 4K60 4:4:4 / HDR 18G 100m HDMI extender set with IR, RS232, Ethernet Pass Through,Complete set includes TX, RX, power supply, and IR flasher/emitter Extend HDMI 2.0 signals up to 4K@60Hz / 4:4:4 up to 100m (4K 70m / 1080P 100m). Extends bi-directional IR, RS232 and ethernet pass through. Should Support HDR10 and should be HDCP 2.2 compitable. |
| 1341 | Supply, Installation, Testing and Commissioning of4K HDMI & USB-C to HDMI Scaler. 18G 4K HDMI to HDMI Digital Scaler with HDMI and USB–C Inputs & HDMI Scaled output up to 4K @ 60 Hz (4:4:4). 2x1 AV switcher, unit up or down scales the selected video signal to 4K @ 60 Hz (4:4:4), Minimum data rate 18 Gbps, HDCP 2.2 and 1.4 compliant, supports CEC, OSD menu, features Input Auto–Switching, Constant Sync on the output even if the input video signal is lost or interrupted, Contact Closure Switches: On a 3–pin terminal block, USB: On a USB–A connector for firmware upgrade, Certification: CE, ISO 9001, ISO 14001, OHSAS 18001. Should be supplied with standard accessories as required. |
| 1342 | Supply, installation, testing & Commissioning of Full HD 1080p, minimum 20X Optical Zoom, min 100 Presets, 60 Frames per Second, Ethernet Out, HDMI Out, 3G-SDI Out, Audio In, RS232/422 Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle , Should support PoE. For capturing students. |
| 1343 | Supply, lnstallatian, Testing & Commissioning of Recording, Streaming & Webcasting Hardware simultaneously, Built-in 4 Inputs (HDMI /IP/3G-SDI/DVI) HDMI Out, Can record upto any three inputs simultaneously in a single frame and as well as individual sources simultaneously, Should have minimum 1TB inbuilt storage, Should be able to support minimum 3 unicast streams |
| 1344 | Supply, lnstallatian, Testing & Commissioning of Joystick for PAN/Tilt/Zoom and Focusing, IP & RS232C/RS455 Communication Interfaces, High Brightness OLED Display, Auto Backlit Keys, Should be able to control minimum 100 Cameras on IP & 10 Cameras through RS232/422, Should support PoE. |
| 1345 | Supply, installation, testing & Commissioning of Digital Podium with 21.5" Interactive Screen. Customized Wooden house structure (Post Forming) Dimensions 590 mm x 600 mm x 1200 mm with caster wheels & brakes. Drawer for keyboard, mouse, and document camera. Wooden Top Tray for placing document & Laptop. All drawers sliding tray and doors should be Lockable. External Connectivity: Having 2 X USB, one MIC XLR, 1 VGA IN Audio IN (3.5mm Female), 1 HDMI IN, Power Socket with ON/OFF. Internal Connectivity (Optional): Internal Connectivity: 4 x 2 HDMI Matrix Switcher with Auto-switching, Video resolution up to 4K2K@60hz 4:4:4 Inbuilt Audio extractor. 8 Universal 5 Amp Socket power strip. Provision of 19" Rack space inside podium to place PC, amplifier, and other equipment.Interactive Display: Interactive Panel Size of 21.5" Diagonal, Panel Type: IPS LCD, Display. Resolution: 1920 x 1080. Touch Technology: Electromagnetic Touch Digitizer Battery-less Pen with backside eraser. |
| 1346 | Supply, Installation, Testing and Commissioning of Control system have minimum 8 bidirectional RS232, 8 IR, 8 Relays and 8 GP/IO and 1 Ethernet port to control all the devices in the room. Should have inbuilt or external IR sensor/learner to learn IR commandsThe compatible relay controller to control the Projector screen up down should be supplied as a package (may be from same OEM of controller or different).Should have inbuilt processing power and internal storage to store and process the control program.Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size.Additional ports if required can be added with minimum hassle.Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings. Should have Status LED to check for Control/Connection status. It should have minimum 5 license each included for both iOS & Android application Certification: CE, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment maybe added to match the complete specs. Should be supplied with standard accessories as required. |
| 1347 | Supply, Installation, Testing and Commissioning ofWall & Table Mount PoE Touch Panel have 7” or more IPS color screen.Should have minimum 1280 x 800 resolution, brightness 4000cd/m2, contrast ratio 800:1, 16:10 aspect ratio Should have inbuilt Wi-Fi, 802.11 b/g/n/ac, Bluetooth 4.0 Should have capacitive touch technology. Should support Multitouch. CPU performance: 1.6GHz Quad Core, GPU, 2GB RAM, 16GB flash. Should be able to decode video format HEVC/H.265, H.264, H.263, MPEG–1/2/4, VC–1, VP6/8, RV8/9/10, AVS, MVC, Sorenson Spark, M–JPEG Should be able to encode/stream video format H.264, MVC, VP8, M–JPEG Should have front 2MP camera, HD 720p. Should have Ethernet port 10/100/1000Mbps PoE LAN. Should have inbuilt mic and speaker. Should be provided with table mount & wall mount kit. Secured Operation - Highly secured operation of applications using password protection, hidden control buttons and more. Red LED alert when camera is active. should be possible with Customized GUI using same OEM GUI Software. should support native integration of same OEM enterprise management software. Certification: CE, FCC, ROHS, REACH, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment may be added to match the complete specs. Should be supplied with standard accessories as required. |
| 1348 | Supply , installation , testing and commissioning ofWorkstation with i-7 Configuration. Server: Intel Core i7, such as Intel Core i7-4770 Quad-Core 3.4Ghz 8 GB DDR3-1600 RAM 1 Gbit/s Network Hard drive SATA 6 Gbit/s 7200 RPM Enterprise Class – Up to 48 Mbps per drive for optimal performance. Client: Intel Core i7, such as Intel Core i7-4770 Quad Core 3.4Ghz 8 GB DDR3-1600 RAM , Bandwidth supported - Up to 256 Mbit/s video data. Should include Keyboard and Mouse and 21.5" FHD Monitor. Should Include AV Control software with customized GUI,. Audio Conference Management Software andWindow 10.or its equivalent in specifications |
| 1349 | Supply, installation, testing & Comissioning ofbiamped, coaxial two-way point source loudspeaker with a single 12-15" LF driver and compression driver with 3" or better Voice coil. Frequency Range (-10dB) of 60Hz - 20kHz or better & long term Continuous Power Handling of 300W (Low frequency) and 45W for High Frequency driver. or better. or better. The Loudspeaker module shall have a Max. SPL (Peak) of MF/HF>= 131 or better. It should have Horizontal dispersion pattern of 110º or better, vertical dispersion of the loudspeaker shall be 60 degrees or better. The loudspeaker shall be enclosed in a baltic birch plywood enclosure with perforated steel grille. |
| 1350 | Supply , installation , testing and comissioning of OEM Hanging/ Mounting arrangement for above loudspeakers Suspension complete with standard accessories as required. |
| 1351 | Supply, installation, testing & Commissioning of 15-18" subwoofer having a usable Freq. Range of 35Hz - 130Hz. It should have a Sensitivity of > = 96dB (1W/1m) or more delivering a ground position Max. Calculated SPL(peak) of>=130 db. The loudspeaker should have a nominal impedance: 8ohm or more and peak Power Handling of 2800W or more. Subwoofer shall be enclosed in Baltic birch plywood enclosurewith 16 or more rigging points for installation flexibility. Shall be supplied with suspenssion Bracket as required. |
| 1352 | Supply, installation, testing & Commissioning of Low profile High SPL all weather stage monitor loudspeakers with 5" LF Driver & 1.5" or better VC compression driver; Frequency Range of90 Hz - 18 kHz or better; Nominal Dispersion : 100°H x 100°V with rotatable horn; Long term Power handling of 400 W peak or better; Sensitivity : 90 dB; Max SPL : 116dB Peak; Nominal Impedance : 8?;18-gauge (1.2 mm) perforated steel; Powder-coated finish grille with Two-part spray polyurethane coating Enclosure. Shall include In-box 100W OEM Input transformer kit for Distributed system applications. Standard wall bracket shall be included.Shall be rated for IP55 outdoor installations as per IEC 529 specs. |
| 1353 | Supply, installation, testing & Commissioning of Low profile High SPL all weather Front Fill loudspeakers with 8" LF Driver & 1.5" or better VC compression driver; Frequency Range of80 Hz - 16 kHz or better; Nominal Dispersion : 90°H x 60°V with rotatable horn; Long term Power handling of 200 W or better; Sensitivity : 91 dB; Max SPL : 120dB Peak; Nominal Impedance : 8?;18-gauge (1.2 mm) perforated steel; Powder-coated finish grille with Two-part spray polyurethane coating Enclosure. Shall include In-box 100W OEM Input transformer kit for Distributed system applications. Standard wall bracket shall be included.Shall be rated for IP55 outdoor installations as per IEC 529 specs. |
| 1354 | Supply, installation, testing & Commissioning of Low profile High SPL all weather Side/Rear Fill loudspeakers with dual 8" LF Driver & 1.5" or better VC compression driver; Frequency Range of80 Hz - 16 kHz or better; Nominal Dispersion : 90°H x 60°V with rotatable horn; Long term Power handling of 300 W or better; Sensitivity : 91 dB; Max SPL : 120dB Peak; Nominal Impedance : 8?;18-gauge (1.2 mm) perforated steel; Powder-coated finish grille with Two-part spray polyurethane coating Enclosure. Shall include In-box 100W OEM Input transformer kit for Distributed system applications. Standard wall bracket shall be included.Shall be rated for IP55 outdoor installations as per IEC 529 specs. |
| 1355 | Supply, installation, testing & Commissioning ofCompactIndoor/Outdoor type IP55 rated wall mount Music Loudspeaker: Free field Frequency range (-10dB) of 83Hz to 19kHz; Power handling of 64 Watt peak; Nominal dispersion of 145 H X 140 V; Free field Sensitivity of 87 dB SPL and Max SPL of 105 dB SPL peak; Nominal Impedance 8 Ohms; Integral multi-tap Transformer with tap settings of 2/4/8/16 W @ 100V. with Powder-coated steel grille; Brackets with pitch/yaw adjustment included. |
| 1356 | Supply, installation, testing & Commissioning of 35W Analog Volume control for Male & Female Room with Attenuation Steps (1.5dB or 3dB Steps), Total Attenuation: 27dB, Insertion Loss: .6dB, Complete with standard accessories as required. |
| 1357 | Supply, Installation, testing and commissioning of intregrated Class D zone amplifier with output power of upto 90W @ 70/100V. frequency response of 50Hz to 20kHz; THD <0.3%; Shall include priority override and Fire alarm interface, shall include necessary loudspeaker EQs. |
| 1358 | Supply, installation, testing & Comissioning of Dual channel class D Power amplifier with a Max Output Power of 2x600W@4-8 ohms as well 70/100V or bridged mode output power of 1 x 1200W @ 2/4 ohms and 70/100V. Frequency Response of 20Hz - 20 KHz(+/- 1 dB @ 1 W),THD+N <0.04%; Senstivity: -10dBV to +14dBu; Should have 2 outputs with dynamic power >100 dBA, Input impedance 10KO complete with standard accessories as required. Shall have protection over , high temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage offer & optional Network audio connectivity through RJ-45 port for expansion. |
| 1359 | Supply, installation, testing & Comissioning of Dual channel class D Power amplifier with a Max Output Power of 2x 1000W@4-8 ohms as well 70/100V or bridged mode output power of 1x 2000W @ 2/4 ohms and 70/100V. Frequency Response of 20Hz - 20 KHz(+/- 1 dB @ 1 W), THD+N <0.04%; Senstivity: -10dBV to +14dBu; Should have 2 outputs with dynamic power >100 dBA, Input impedance 10KO complete with standard accessories as required. Shall have protection over , high temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage offer & optional Network audio connectivity through RJ-45 port for expansion. |
| 1360 | Supply, installation, testing & Comissioning of class D Power amplifier with a Max Output Power of 4x 300W@4-8 ohms as well 70/100V or bridged mode output power of 2x 600W @ 2/4 ohms and 70/100V. Frequency Response of 20Hz - 20 KHz(+/- 1 dB @ 1 W),THD+N <0.04%; Senstivity: -10dBV to +14dBu; Should have 2 outputs with dynamic power >100 dBA, Input impedance 10KO complete with standard accessories as required. Shall have protection over , high temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage offer & optional Network audio connectivity through RJ-45 port for expansion. |
| 1361 | Supply , installation , testing and Commissioning of Digital SoundProcessor with 8 Mic/Line inputs & 8 analog outputs, 24 Bit A-D and D-A Convertors; Sampling Rate : 48 kHz;THD : < 0.002 % ; Channel Separation (Crosstalk) : < 105 dB ; Frequency Response 20 Hz - 20 kHz ; Signal-to-Noise Ratio 80 dB ;Dynamic Range :> 115 dB; 5 Control Inputs and Outputs; RS-232 and Ethernet Port for third party Control and Monitoring; inbuilt DSP features like Input Equalizers, Router, Band Pass filter, Output Equalizer, Delay, Limiters, gates, Feedback suppressors, Source selectors etc. |
| 1362 | Supply, installation, testing and Commissioning of Wireless Handheld Mic-Supply of Handheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz |
| 1363 | Supply, installation, testing and Commissioning of Wireless Lapel Mic-Supply of Wireless Lapel Mic with Cardiod polar pattern for transmitter , Receiver & Transmitter frequency response 100Hz-18kHz or better,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 5.6 mV/Pa,modulation:+/-40kHz . |
| 1364 | Supply, installation, testing and Commissioning of Wired Vocal Microphone with on/off switch, Super cardioid vocal microphone, Audio frequency bandwidth :70 - 20000 Hz, Sensitivity2.6 mV/Pa |
| 1365 | Supply, installation, testing and Commissioning of Wired Dynamic Instrument Microphone, Cardioid Dynamic Instrument Microphone, Audio frequency bandwidth =40 - 20000 Hz, Sensitivity at 1000 Hz 2.5 mV/Pa (–52 dBV re 1 V/Pa), Max. SPL for 1 % THD = 47 dB SPL |
| 1366 | Supply, installation, testing and Commissioning of Wired Gooseneck Microphone with Desktop base unit and on/off switch for Podium, Desktop gooseneck Mic, Audio frequency bandwidth =70 - 18000 Hz, Signal to Noise:64 dB-A, Length =500 mm, Voltage =9 to 52 V Power Interface |
| 1367 | Supply, installation, testing and Commissioning of Central Control Unit-Supply of The Audio Powering Switch shall be responsible for routing, controlling and processing the audio and supplies power to the multimedia devices. It includes an intelligent adaptive acoustic feedback suppressor, echo cancellation and two 5-band parametric equalizers for optimal speech intelligibility - Zero network configuration - Fully compatible to the Ethernet (IEEE802.3) and OMNEO standard - Supports loop-through connection with cable redundancy - Standby mode to be environment friendly - Mains switch on the rear to power on the audio powering switch. - Ground-lift switch. -Led on the front to show: green (power on), amber (standby), blinking (no connection to the system). -Ethernet led’s yellow and amber for each socket. - Independent powered sockets; a short circuit on one socket does no influence the other sockets. - Supports hot plug and play. |
| 1368 | Supply, Installation, Testing and Commissioning of Customized Floor Box with Line Out and Power socket for Stage Monitor, 4x XLR female Connectors for Wired Microphones connectivity Complete with standard accessories as required. |
| 1369 | Supply, Installation, Testing and Commissioning of Customized Floor Box with HDMI, VGA+Audio connectivity for podium and 1x XLR female Connector for Gooseneck Microphone Connectivity Complete with standard accessories as required. |
| 1370 | Supply, Installation, Testing and Commissioning of 24-port 1000base-T Gigabit PoE+ Smart Managed Switch. . Should have Network Protocol and Standards Compatibility IEEE 802.3 Ethernet. IEEE 802.3i 10BASE-T.IEEE 802.1x. complete with standard accessories as required. |
| 1371 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1372 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1373 | Supply, Installation, Testing and Commissioning of 10 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1374 | Supply, installation , testing and Commissioning of VGA with Audio cable (10 feet). High-performance cable with male 15-pin HD and 3.5mm stereo audio connectors at each end. Should have Gold Plated pins. Should have conductor 26 AWG 7/34 tinned copper All pins should be connected for DDC2 and EDID support. Should be maximum 0.35 inch in diameter. Outer Jacket should be HD polyethylene, Dielectric: Foam polyethylene. Compliance: UL: CL2, CSA: C(UL) CL2 |
| 1375 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1376 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 4.0 Sqmm (128/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. Approved Make: Krystal/Belden/Liberty AV |
| 1377 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 2.5 Sqmm (80/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. Approved Make: Krystal/Belden/Liberty AV |
| 1378 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1379 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1380 | Supply, Installation,Testing & Commissioning of 24 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1381 | Meeting Room 19 Pax at First Floor Supply, Installation, Testing and Commissioning of 1-chip DLP LASER Multimedia Projection system having, 7000 Lumens 20000 hours lamp life,1920 x 1200 WUXGA Native Resolution, Inbuilt blending and warping with automatic caliberation software, 3D ready, 1200000:1 Contrast Ratio, inputs: HDBaseT,HDMI2.0, DVI-D, Active 3D, Motorised zoom and focus, alongwith 1.25-2.0 lens complete with installation as per the site requirement. |
| 1382 | Supply, Installation, Testing and Commissioning of Customized projector Mount Kit for the above projector complete with standard accessories as required. |
| 1383 | Supply, Installation,Testing & Commissioning of 137" diagonal motorized projection screen with an aspect ratio of 16:10. Screen fabric should in accordance with DIN 4102-1 Class B2 materials. Screen should Sustain temperature of 23 ± 2 °C, and a relative humidity of 50 ± 6 %. Should equipped with RS 232/485 Relay Connectivity. Screen Should have Anti Heat Cut off Option to avoid any Calamity at site. Heavy Dowel to maintain Flatness. Screen Fabric should meet the requirements of Class B2 of building materials. Should be supplied with complete standard accessories as required. |
| 1384 | Supply, Installation,Testing & Commissioning of Flush mount Cable Manager with multi-format cables and a comfortable flip-open cover. Shall have 1x universal Power socket, 1x HDMI Cable, 1x USB Charger and 1x USB etc. complete with standard accessories as required. |
| 1385 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1386 | Supply, lnstallatian, Testing & Commissioning of 8x8, 4K60 4:4:4 / HDR 18G HDMI Matrix switcher with audio de-embed, IR, RS232, & TCP/IP control. All HDMI I/O should support full 18G 4K@60Hz 4:4:4 HDCP 2.2 and 4K HDR. Shall support Third party IR, RS232 and IP control. Shall have Manual DIP switch for EDID management. Shall have Analog and digital de-embedded audio outputs for each output. |
| 1387 | Supply, lnstallatian, Testing & Commissioning of 4K60 4:4:4 / HDR 18G 70m HDMI extender set with IR, RS232, Ethernet Pass Through,Complete set includes TX, RX, power supply, and IR flasher/emitter Extend HDMI 2.0 signals up to 4K@60Hz / 4:4:4 up to 70m (4K 70m / 1080P 700m). Extends bi-directional IR, RS232 and ethernet pass through. Should Support HDR10 and should be HDCP 2.2 compitable. |
| 1388 | Supply, lnstallatian, Testing & Commissioning of USB 2.0 PTZ Web Conferencing Camera, oom UC Feature: Supports all Zoom Room features and has been tested to conform with the latest Zoom Certification Program for the highest performance and ultra-reliability. Compatibility:Most leading video conferencing software and platforms such as Microsoft Teams, Google Meet, Zoom, and many others, Resolution: Full HD Resolution providing resolution up to 1920x 1080P with a frame rate up to 30fps, Optical Zoom: 10x providing a horizontal field of view range between 8.8° (tele) to 66° (wide). AV Outputs: USB 2.0, shall support multiple control protocols like IR, UVC, VISCA, Pelco. Shall be supplied complete with standard accessories as required. |
| 1389 | Supply, Installation, Testing and Commissioning of four-input USB switchers that allow switching between multiple host devices and multiple USB peripherals. Should be USB 2.0 compatible, Enables 4 computers to share 4 USB 3.2 Gen1 devices, Support port selection via remote controller or RS-422/RS-485 link through 5-pin terminal block. Supports DC 9-24V power input by terminal block, Supports USB BC 1.2 and over current protection. |
| 1390 | Supply, Installation, Testing and Commissioning of USB 2.0 Extender Kit Extends USB High-Speed (480 Mbps) up to 100 m (330 ft) & supports isochronous data for use with USB Cameras, Includes transmitter and receiver. Can be powered at either the client or host device, Supplies 500mA to USB devices. Shall be supplied complete with standard accessories as required. |
| 1391 | Supply, Installation, Testing and Commissioning ofWall & Table Mount PoE Touch Panel have 7” or more IPS color screen.Should have minimum 1280 x 800 resolution, brightness 4000cd/m2, contrast ratio 800:1, 16:10 aspect ratio Should have inbuilt Wi-Fi, 802.11 b/g/n/ac, Bluetooth 4.0 Should have capacitive touch technology. Should support Multitouch. CPU performance: 1.6GHz Quad Core, GPU, 2GB RAM, 16GB flash. Should be able to decode video format HEVC/H.265, H.264, H.263, MPEG–1/2/4, VC–1, VP6/8, RV8/9/10, AVS, MVC, Sorenson Spark, M–JPEG Should be able to encode/stream video format H.264, MVC, VP8, M–JPEG Should have front 2MP camera, HD 720p. Should have Ethernet port 10/100/1000Mbps PoE LAN. Should have inbuilt mic and speaker. Should be provided with table mount & wall mount kit. Secured Operation - Highly secured operation of applications using password protection, hidden control buttons and more. Red LED alert when camera is active. should be possible with Customized GUI using same OEM GUI Software. should support native integration of same OEM enterprise management software. Certification: CE, FCC, ROHS, REACH, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment may be added to match the complete specs. Should be supplied with standard accessories as required. |
| 1392 | Supply, Installation, Testing and Commissioning of Control System.Controller with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control all the devices in the room.Should have inbuilt or external IR sensor/learner to learn IR commands. The compatible relay controller to control the Projector screen up down should be supplied as a package (may be from same OEM of controller or different).Should have inbuilt processing power and internal storage to store and process the control program.Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size.Additional ports if required can be added with minimum hassle.Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings. Should have Status LED to check for Control/Connection status. It should support PoE. It should have minimum 5 license each included for both iOS & Android application. Certification: CE, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment maybe added to match the complete specs. |
| 1393 | Supply, Installation, testing and commissioning of intregrated Class D Dual zone amplifier with output power of upto 2x120W @ 70/100V. frequency response of 55 Hz - 20 kHz (+0/–3 dB, @ 1 W reference 1 kHz); THD <0.3% at rated power. Channel Separation = –60 dBV (below rated power, 1 kHz), Dynamic range > 88 dB. |
| 1394 | Supply, Installation, Testing and commissioning of AEC capable Digital Audio Conferencing Processor with at least 12 AEC Mic/Line inputs & 8 analog outputs, 24 Bit A-D and D-A Convertors; Sampling Rate : 48 kHz;THD : < 0.002 % ; Channel Separation (Crosstalk) : < 108 dB ; Frequency Response 20 Hz - 20 kHz ; Signal-to-Noise Ratio 90 dB ;Dynamic Range > 115 dB; 5 Control Inputs and Outputs; RS-232 and Ethernet Port for third party Control and Monitoring; 64x64 Bidirectional DANTE Audio Networking ports, Shall include standard Connectivity features like VOIP, POTS, USB Audio etc. inbuilt DSP features like Conference room Routers,Input Equalizers, Router, Band Pass filter, Output Equalizer, Delay, Limiters, gates , Source selectors etc. Shall Support at least 15 remote Zone controllers complete with standard accessories as required. |
| 1395 | Supply, Installation, Testing and commissioning of Chairman Unit-Supply of The extended discussion device shall have a 4.3 inch touch screen and it shall be completely software upgradable. It shall have a lot of features including independent dual-use for language selection and voting. It shall have a simple software setting to enable two participants to share a device and listen to proceeding in two different languages. The 4.3 inch capacitive touch screen shall inform participants of the proceedings and increases meeting efficiency by displaying the current speaker and delegates in the request list. The device shall have the following features and benefits: • Single-use and chairperson can be configured via the PC configuration software application. • Supports star and loop-trough connection. • capacitive multi-touch screen for displaying: – Multiple user interface languages in original characters. – Speaker list and Request list.Screen size 109.22 mm (4.3 inch) Screen type capacitive multi-touch Supply voltage 48 Vdc Power consumption Max 5W Frequency response100 Hz – 20 kHz (-3 dB at nominal level) THD at nominal level < 0.1 % Dynamic range> 90 dB |
| 1396 | Signal-to-noise ratio> 90 dBThe ‘pluggable high-directive microphone’ shall be a stylish high-directive microphone that shall give the user a clear view of the meeting room, due to its unobtrusive design. The high-directive microphone shall contain two precisely positioned capsules to give it a high-directive response. This shall make it possible to have a larger speaking distance than normal from the microphone, even in noisy conditions. The microphone shall have the following features and benefits: • Discrete microphone for user convenience. • High-directive response. • Ultra-low noise. • Low susceptibility to interference from mobile phones. The microphone shall have the following controls and indicators: • Red or green illuminator. Red shall indicate that the microphone is active; green shall indicate that the request-to-speak is accepted. Frequency Bandwidth100 Hz – 15 kHzaccording IEC60914 Dynamic range > 96 dB |
| 1397 | Supply, Installation, Testing and commissioning ofDelegate Unit-Supply of The discussion device shall have the following features and benefits: - Supports star and loop-trough connection. - Dual-use functionality enabled by use of software. - Audio mute button - Encryption ensures that information within the system remains confidential The device shall have a headphone connection and independent volume control (on both sides of the device), so the speaker can be heard clearly even when there is excessive background noise Frequency response100 Hz – 20 kHz (-3 dB at nominal level) THD at nominal level < 0.1 % Dynamic range> 90 dB Signal-to-noise ratio> 90 dB Operating temperature 5 ºC to +45 ºC The ‘pluggable high-directive microphone’ shall be a stylish high-directive microphone that shall give the user a clear view of the meeting room, due to its unobtrusive design. The high-directive microphone shall contain two precisely positioned capsules to give it a high-directive response. This shall make it possible to have a larger speaking distance than normal from the microphone, even in noisy conditions. |
| 1398 | The microphone shall have the following features and benefits: • Discrete microphone for user convenience. • High-directive response. • Ultra-low noise. • Low susceptibility to interference from mobile phones. The microphone shall have the following controls and indicators: • Red or green illuminator. Red shall indicate that the microphone is active; green shall indicate that the request-to-speak is accepted. Frequency Bandwidth100 Hz – 15 kHzaccording IEC60914 Dynamic range > 96 dB |
| 1399 | Supply, Installation, Testing and commissioning of License-Server Software, Participant Database , Identification at seat License for above cobferencing system |
| 1400 | Supply, Installation, Testing and commissioning of Powering Switch- Additionalpower swithing device for Chairman Unit and Delegate Units |
| 1401 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1402 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 1.5 Sqmm (48/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. |
| 1403 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1404 | Supply, Installation, Testing and Commissioning of 10 ft USB Cable with USB "A" Plug (Male) to "B" Plug (Male) Connectivity, In-Line format, Molded PVC connector housings, USB 1.1, 2.0 and 3.0 Compliant. |
| 1405 | Supply, Installation, Testing and Commissioning of 6 ft USB Cable with USB "A" Plug (Male) to "B" Plug (Male) Connectivity, In-Line format, Molded PVC connector housings, USB 1.1, 2.0 and 3.0 Compliant. |
| 1406 | Supply, Installation, Testing and Commissioning of 1m USB 3.2 Gen2 C to C Pre-Made Cable, Supports Audio/Video, Data, & Power, Molded PVC connector housings, Backwards compatible to USB 3.0, 2.0, and 1.1. Rated for 3A current and charging. |
| 1407 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1408 | Supply, Installation, Testing and Commissioning of 8-port 1000base-T Gigabit PoE+ Smart Managed Switch. . Should have Network Protocol and Standards Compatibility IEEE 802.3 Ethernet. IEEE 802.3i 10BASE-T.IEEE 802.1x. complete with standard accessories as required. |
| 1409 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1410 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1411 | Supply, Installation,Testing & Commissioning of 18 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1412 | Meeting Room 11 Pax 2 nosat Second and Third Floor Supply, Installation, Testing and Commissioning of 86" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity, HDMI 2.0,DP1.2, HDR10,400 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1413 | Supply, Installation,Testing & Commissioning of Flush mount Cable Manager with multi-format cables and a comfortable flip-open cover. Shall have 1x universal Power socket, 1x HDMI Cable, 1x USB Charger and 1x USB etc. complete with standard accessories as required. |
| 1414 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1415 | Supply„lnstallatian, Testing & Commissioning of 4x2 HDMI 2.0 Matrix Switcher with 4K60 4:4:4 / HDR 18G 4x2 Matrix switcher with ARC, audio de-embedding, Down Scaling, IR, TCP/IP, & RS232 Control, Routes 4 HDMI 2.0 sources to 2 4K HDR Ultra HD displays, HDMI 2.0b and HDCP 2.2 compliant, Supports up to 4K60 4:4:4 with static and dynamic HDR support, Analog and digital audio de-embedded from output 1, Built in auto down scaling on each output, Control: TCP/IP, RS-232, IR, Push button or built in web GUI, Integrated CEC controller can power on / off connected displays. |
| 1416 | Supply, Installation, Testing and Commissioning of four-input USB switchers that allow switching between multiple host devices and multiple USB peripherals. Should be USB 2.0 compatible, Enables 4 computers to share 4 USB 3.2 Gen1 devices, Support port selection via remote controller or RS-422/RS-485 link through 5-pin terminal block. Supports DC 9-24V power input by terminal block, Supports USB BC 1.2 and over current protection. |
| 1417 | Supply, lnstallatian, Testing & Commissioning of USB 2.0 PTZ Web Conferencing Camera, oom UC Feature: Supports all Zoom Room features and has been tested to conform with the latest Zoom Certification Program for the highest performance and ultra-reliability. Compatibility:Most leading video conferencing software and platforms such as Microsoft Teams, Google Meet, Zoom, and many others, Resolution: Full HD Resolution providing resolution up to 1920x 1080P with a frame rate up to 30fps, Optical Zoom: 10x providing a horizontal field of view range between 8.8° (tele) to 66° (wide). AV Outputs: USB 2.0, shall support multiple control protocols like IR, UVC, VISCA, Pelco. Shall be supplied complete with standard accessories as required. |
| 1418 | Supply , installation , testing and commissioning of Ceiling Flush Music/PA Loudspeaker, Free field Frequency range (-10dB) of 84Hz to 19kHz; Power handling of 64 Watt peak; Nominal dispersion of 140° Conical; Free field Sensitivity of 86 dB SPL and Max SPL of 104 dB SPL peak; Nominal Impedance 16 Ohms; Integral multi-tap Transformer with tap settings of 2/4/8/16 W @ 100V. with Powder-coated steel grille; Shall include necessary standard hardware for ceiling install. |
| 1419 | Supply, Installation, testing and commissioning of intregrated high impedence Class D zone amplifier with output power of upto 90W @ 70/100V. frequency response of 50Hz to 20kHz; THD <0.3%; Shall include priority override and Fire alarm interface, shall include necessary loudspeaker EQs. |
| 1420 | Supply, Installation, Testing and commissioning of AEC capable Digital Audio Conferencing Processor with at least 4Mic/Line inputs & 4 analog outputs, 24 Bit A-D and D-A Convertors; Sampling Rate : 48 kHz;THD : < 0.002 % or better; Frequency Response 20 Hz - 20 kHz ;Dynamic Range > 115 dB or better, 1 control input ,1 telephone input ; RS-232 and Ethernet Port for third party Control and Monitoring; 16x16 or moreBidirectional DANTE Audio Networking ports, Shall include standard Connectivity features like VOIP, POTS, USB Audio etc. inbuilt DSP features like Conference room Routers,Input Equalizers, Router, Band Pass filter, Output Equalizer, Delay, Limiters, gates , Source selectors etc. |
| 1421 | Supply„lnstallatian, Testing & Commissioning of 2ft X 2ft ceiling microphone with the automatic beamforming focus, the ceiling microphoneshould have 28no. Omni - directional microphone, four corners lighting indications, should have 104 dB or better SPL, 2 x Digital Dante Network Audio, 93 dB(A) or better Dynamic Range, operating temperature 0 to 40 °C, Safety certification: UL62368 certification etc complete with standard accessories as required. |
| 1422 | Supply, Installation, Testing and Commissioning ofWall & Table Mount PoE Touch Panel have 7” or more IPS color screen.Should have minimum 1280 x 800 resolution, brightness 4000cd/m2, contrast ratio 800:1, 16:10 aspect ratio Should have inbuilt Wi-Fi, 802.11 b/g/n/ac, Bluetooth 4.0 Should have capacitive touch technology. Should support Multitouch. CPU performance: 1.6GHz Quad Core, GPU, 2GB RAM, 16GB flash. Should be able to decode video format HEVC/H.265, H.264, H.263, MPEG–1/2/4, VC–1, VP6/8, RV8/9/10, AVS, MVC, Sorenson Spark, M–JPEG Should be able to encode/stream video format H.264, MVC, VP8, M–JPEG Should have front 2MP camera, HD 720p. Should have Ethernet port 10/100/1000Mbps PoE LAN. Should have inbuilt mic and speaker. Should be provided with table mount & wall mount kit. Secured Operation - Highly secured operation of applications using password protection, hidden control buttons and more. Red LED alert when camera is active. should be possible with Customized GUI using same OEM GUI Software. should support native integration of same OEM enterprise management software. Certification: CE, FCC, ROHS, REACH, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment may be added to match the complete specs. Should be supplied with standard accessories as required. |
| 1423 | Supply, Installation, Testing and Commissioning of Control System.Controller with Minimum 4 bidirectional RS232, 4 IR, 4 Relays and 4 GP/IO and 1 Ethernet port to control all the devices in the room.Should have inbuilt or external IR sensor/learner to learn IR commands. The compatible relay controller to control the Projector screen up down should be supplied as a package (may be from same OEM of controller or different).Should have inbuilt processing power and internal storage to store and process the control program.Should be compatible with any (IOS/Android) wireless or wired Touch screen of any size.Additional ports if required can be added with minimum hassle.Should have the flexibility to add as many user interfaces as required. Should have embedded webpage for control port settings. Should have Status LED to check for Control/Connection status. It should support PoE. It should have minimum 5 license each included for both iOS & Android application. Certification: CE, ISO 9001, ISO 14001, OHSAS 18001. Extra component or equipment maybe added to match the complete specs. |
| 1424 | Supply, Installation, Testing and Commissioning of 8-port 1000base-T Gigabit PoE+ Smart Managed Switch. . Should have Network Protocol and Standards Compatibility IEEE 802.3 Ethernet. IEEE 802.3i 10BASE-T.IEEE 802.1x.complete with standard accessories as required. |
| 1425 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1426 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1427 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 1.5 Sqmm (48/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. |
| 1428 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1429 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1430 | Supply, Installation, Testing and Commissioning of 8 MHigh Retention High-Speed HDMI Cables with Ethernet. Fully shielded from connector shroud to shroud. 4K video, Audio Return, Ethernet, CEC, NEC CL2, CEC CMG FT4, RoHS/REACH Compliant. Low-profile molded head. CL2 and CMG FT4 rated, RoHS compliant. |
| 1431 | Supply, Installation, Testing and Commissioning of 10 MHigh Retention High-Speed HDMI Cables with Ethernet. Fully shielded from connector shroud to shroud. 4K video, Audio Return, Ethernet, CEC, NEC CL2, CEC CMG FT4, RoHS/REACH Compliant. Low-profile molded head. CL2 and CMG FT4 rated, RoHS compliant. |
| 1432 | Supply, Installation, Testing and Commissioning of 10 ft USB Cable with USB "A" Plug (Male) to "B" Plug (Male) Connectivity, In-Line format, Molded PVC connector housings, USB 1.1, 2.0 and 3.0 Compliant. |
| 1433 | Supply, Installation, Testing and Commissioning of 6 ft USB Cable with USB "A" Plug (Male) to "B" Plug (Male) Connectivity, In-Line format, Molded PVC connector housings, USB 1.1, 2.0 and 3.0 Compliant. |
| 1434 | Supply, Installation, Testing and Commissioning of 10 M USB 3.x/2.0/1.1 C-C Active Optical Plenum Cable. Active Optical USB 3.2 Gen 2 up to 10Gbps data rates. Backwards compatible to USB 3.0/2.0/1.1. Powered by the USB BUS of the associated Host. |
| 1435 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1436 | Supply, Installation,Testing & Commissioning of 12 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1437 | Meeting Room 9 Paxat Fifth Floor Supply, Installation, Testing and Commissioning of 65" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1438 | Supply, Installation,Testing & Commissioning of Flush mount Cable Manager with multi-format cables and a comfortable flip-open cover. Shall have 1x universal Power socket, 1x HDMI Cable, 1x USB Charger and 1x USB etc. complete with standard accessories as required. |
| 1439 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1440 | Supply, Installation, Testing and Commissioning ofall-in-one USB conferencing device that brings premium audio and video to small meeting areas from huddle spaces to medium-sized rooms. Shall have min. Six beam-steering microphones automatically focus on voices in the room and reject noise. Shall have A 4K ultra-HD camera with autoframing delivers crystal-clear video, helping remote participants feel like they’re in the room. Shall support popular Unified Communications platforms such as Microsoft Teams, Google Meet, Zoom, and more. Should support single-cable connectivity that eliminates clutter and an elegant low-profile design that complements the room and improves aesthetics. Speaker Frequency Response (–10 dB): 85 – 20,000 Hz, Maximum SPL @ 1 m : 89 dBor better. Microphone Frequency Response (±3 dB) : 20 – 15,000 Hz, Pickup Range 6.0 m or more, Static and adaptive dynamic beam-forming, 3 exclusion zones, stereo acoustic echo cancellation (AEC), digital noise suppression. |
| 1441 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1442 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1443 | Supply, Installation, Testing and Commissioning of 5 MHigh Retention High-Speed HDMI Cables with Ethernet. Fully shielded from connector shroud to shroud. 4K video, Audio Return, Ethernet, CEC, NEC CL2, CEC CMG FT4, RoHS/REACH Compliant. Low-profile molded head. CL2 and CMG FT4 rated, RoHS compliant. |
| 1444 | Supply, Installation, Testing and Commissioning of 5 M USB 3.x/2.0/1.1 C-C Active Optical Plenum Cable. Active Optical USB 3.2 Gen 2 up to 10Gbps data rates. Backwards compatible to USB 3.0/2.0/1.1. Powered by the USB BUS of the associated Host. |
| 1445 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1446 | Resident Commissioner Office 1 & 2 Supply, Installation, Testing and Commissioning of 65" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1447 | Supply, Installation,Testing & Commissioning of Flush mount Cable Manager with multi-format cables and a comfortable flip-open cover. Shall have 1x universal Power socket, 1x HDMI Cable, 1x USB Charger and 1x USB etc. complete with standard accessories as required. |
| 1448 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1449 | Supply, Installation, Testing and Commissioning ofall-in-one USB conferencing device that brings premium audio and video to small meeting areas from huddle spaces to medium-sized rooms. Shall have min. Six beam-steering microphones automatically focus on voices in the room and reject noise. Shall have A 4K ultra-HD camera with autoframing delivers crystal-clear video, helping remote participants feel like they’re in the room. Shall support popular Unified Communications platforms such as Microsoft Teams, Google Meet, Zoom, and more. Should support single-cable connectivity that eliminates clutter and an elegant low-profile design that complements the room and improves aesthetics. Speaker Frequency Response (–10 dB): 85 – 20,000 Hz, Maximum SPL @ 1 m : 89 dBor better. Microphone Frequency Response (±3 dB) : 20 – 15,000 Hz, Pickup Range 6.0 m or more, Static and adaptive dynamic beam-forming, 3 exclusion zones, stereo acoustic echo cancellation (AEC), digital noise suppression. |
| 1450 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1451 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1452 | Supply, Installation, Testing and Commissioning of 5 MHigh Retention High-Speed HDMI Cables with Ethernet. Fully shielded from connector shroud to shroud. 4K video, Audio Return, Ethernet, CEC, NEC CL2, CEC CMG FT4, RoHS/REACH Compliant. Low-profile molded head. CL2 and CMG FT4 rated, RoHS compliant. |
| 1453 | Supply, Installation, Testing and Commissioning of 5 M USB 3.x/2.0/1.1 C-C Active Optical Plenum Cable. Active Optical USB 3.2 Gen 2 up to 10Gbps data rates. Backwards compatible to USB 3.0/2.0/1.1. Powered by the USB BUS of the associated Host. |
| 1454 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1455 | Meeting Room 9 Pax (2 Nos) at Ground Floor Supply, Installation, Testing and Commissioning of 65" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1456 | Supply, Installation,Testing & Commissioning of Flush mount Cable Manager with multi-format cables and a comfortable flip-open cover. Shall have 1x universal Power socket, 1x HDMI Cable, 1x USB Charger and 1x USB etc. complete with standard accessories as required. |
| 1457 | Supply„lnstallatian, Testing & Commissioning of Wireless Presentation Solution, Enables wireless presentation of 4K Wireless Display, App-free, Wireless Touch, Extended Screen support, shall offer Enterprise Management features, up to four Shared screens simultaneously, and annotate in Office 365 apps and share notes to devices or the front-of-room display, Supports display resolutions up to 4K and FUII HD 1080P and UXGA/WUXGA, Provides HDMI / VGA / mini DisplayPort, and analog audio outputs etc. all compJete. |
| 1458 | Supply, Installation, Testing and Commissioning ofall-in-one USB conferencing device that brings premium audio and video to small meeting areas from huddle spaces to medium-sized rooms. Shall have min. Six beam-steering microphones automatically focus on voices in the room and reject noise. Shall have A 4K ultra-HD camera with autoframing delivers crystal-clear video, helping remote participants feel like they’re in the room. Shall support popular Unified Communications platforms such as Microsoft Teams, Google Meet, Zoom, and more. Should support single-cable connectivity that eliminates clutter and an elegant low-profile design that complements the room and improves aesthetics. Speaker Frequency Response (–10 dB): 85 – 20,000 Hz, Maximum SPL @ 1 m : 89 dBor better. Microphone Frequency Response (±3 dB) : 20 – 15,000 Hz, Pickup Range 6.0 m or more, Static and adaptive dynamic beam-forming, 3 exclusion zones, stereo acoustic echo cancellation (AEC), digital noise suppression. |
| 1459 | Supply, Installation, Testing and Commissioning of Wi-Fi router/Access point for wireless meeting collaboration complete with standard accessories as required. |
| 1460 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1461 | Supply, Installation, Testing and Commissioning of 5 MHigh Retention High-Speed HDMI Cables with Ethernet. Fully shielded from connector shroud to shroud. 4K video, Audio Return, Ethernet, CEC, NEC CL2, CEC CMG FT4, RoHS/REACH Compliant. Low-profile molded head. CL2 and CMG FT4 rated, RoHS compliant. |
| 1462 | Supply, Installation, Testing and Commissioning of 5 M USB 3.x/2.0/1.1 C-C Active Optical Plenum Cable. Active Optical USB 3.2 Gen 2 up to 10Gbps data rates. Backwards compatible to USB 3.0/2.0/1.1. Powered by the USB BUS of the associated Host. |
| 1463 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1464 | Dining Hall at Ground Floor Supply, Installation, Testing and Commissioning of 55" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1465 | Supply, Installation, Testing and Commissioning of digital signage player with flawless 4K and Full HD single video decoding, mainstream HTML5 performance and simultaneous playback from local, networked and streaming sources. Includes the standard I/O package of gigabit Ethernet, Video Codecs for 4K content: H.265/H.264, Video Containers for 4K H.265/H.264 content: .ts, .mov, .mp4 , Video Codecs for Full HD: H.265, H.264(MPEG-4, Part 10), MPEG-2, MPEG-1, Video Containers for Full HD: .ts, .mpg, .vob, .mov, .mp4, .m2ts, Images: BMP, JPEG, PNG, Audio: MP2, MP3, AAC, and WAV (AC3 is passed through). 4K resolutions: 4096x2160, 3840x2160, 3840x600. Shall have Built-in/external Storage of 8 GB and expandable up to 2TB. |
| 1466 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1467 | Supply, installation, testing and commissioning of Ceiling purpose subwoofer system: Free field Frequency range appox (-10dB) of 40Hz to 18kHz; Power handling of < >800 Watt peak; Nominal dispersion of 140 Conical;Shall include necessary standard hardware for ceiling install. Subwoofer shall Includesatellite Speakers. |
| 1468 | Supply, installation, testing & Comissioning of class D Power amplifier with a Max Output Power of 4x 300W@4-8 ohms as well 70/100V or bridged mode output power of 2x 600W @ 2/4 ohms and 70/100V. Frequency Response of 20Hz - 20 KHz(+/- 1 dB @ 1 W),THD+N <0.04%; Senstivity: -10dBV to +14dBu; A/D and D/A conveters: 24-bit/48KHz; should have built-in DSP functions including SmartBass processing, routing, level control, delays, limiters, Bose loudspeaker EQs, plus input and area EQs Should have 4 outputs with dynamic power >100 dBA, Input impedance 10KO complete with standard accessories as required. Should have Opti-voice paging for smoothtransition between music & announcements; Shall have protection over , high temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage offer & optional Network audio connectivity through RJ-45 port for expansion. |
| 1469 | Supply, installation, testing & Comissioning of 3 Zone Controller cum Volume Control, type: Passive controller, linear potentiometer 0- 10 k? and 4-position switch, One RJ-45, TIA/EIA 568B wiring standard connector complete with standard accessories as required. |
| 1470 | Supply, installation, testing & Comissioning of Audio input plate having XLR/AUX input to connect the local source. |
| 1471 | Supply, installation, testing & Comissioning of MP3 Media Player. Music Play Mode: Shuffle Playback, Repeat Off, Repeat 1 Song, Repart All, All Range, Selected Range. Display Type:TFT colour display with white LED-backligh, Sound effects: Direct Source (Direct), 10-Band Equaliser, DSEE HX, DC Phase Lineariser, Dynamic Normaliser, ClearAudio+, Vinyl Processor. Built-in rechargeable lithium-ion battery, Wi-Fi 2.4/5 GHz. |
| 1472 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1473 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 2.5 Sqmm (80/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. |
| 1474 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1475 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1476 | Supply, Installation,Testing & Commissioning of 6 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1477 | Fitness Center at Fourth Floor Supply, Installation, Testing and Commissioning of 55" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity, HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1478 | Supply, Installation, Testing and Commissioning of digital signage player with flawless 4K and Full HD single video decoding, mainstream HTML5 performance and simultaneous playback from local, networked and streaming sources. Includes the standard I/O package of gigabit Ethernet, Video Codecs for 4K content: H.265/H.264, Video Containers for 4K H.265/H.264 content: .ts, .mov, .mp4 , Video Codecs for Full HD: H.265, H.264(MPEG-4, Part 10), MPEG-2, MPEG-1, Video Containers for Full HD: .ts, .mpg, .vob, .mov, .mp4, .m2ts, Images: BMP, JPEG, PNG, Audio: MP2, MP3, AAC, and WAV (AC3 is passed through). 4K resolutions: 4096x2160, 3840x2160, 3840x600. Shall have Built-in/external Storage of 8 GB and expandable up to 2TB. |
| 1479 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1480 | Supply, installation, testing and commissioning of Ceiling purpose subwoofer system: Free field Frequency range appox (-10dB) of 40Hz to 18kHz; Power handling of < >800 Watt peak; Nominal dispersion of 140 Conical;Shall include necessary standard hardware for ceiling install. Subwoofer shall Includesatellite Speakers. |
| 1481 | Supply, installation, testing & Comissioning of class D Power amplifier with a Max Output Power of 4x 300W@4-8 ohms as well 70/100V or bridged mode output power of 2x 600W @ 2/4 ohms and 70/100V. Frequency Response of 20Hz - 20 KHz(+/- 1 dB @ 1 W),THD+N <0.04%; Senstivity: -10dBV to +14dBu; A/D and D/A conveters: 24-bit/48KHz; should have built-in DSP functions including SmartBass processing, routing, level control, delays, limiters, Bose loudspeaker EQs, plus input and area EQs Should have 4 outputs with dynamic power >100 dBA, Input impedance 10KO complete with standard accessories as required. Should have Opti-voice paging for smoothtransition between music & announcements; Shall have protection over , high temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage offer & optional Network audio connectivity through RJ-45 port for expansion. |
| 1482 | Supply, installation, testing & Comissioning of 3 Zone Controller cum Volume Control, type: Passive controller, linear potentiometer 0- 10 k? and 4-position switch, One RJ-45, TIA/EIA 568B wiring standard connector complete with standard accessories as required. |
| 1483 | Supply, installation, testing & Comissioning of Audio input plate having XLR/AUX input to connect the local source. |
| 1484 | Supply, installation, testing & Comissioning of MP3 Media Player. Music Play Mode: Shuffle Playback, Repeat Off, Repeat 1 Song, Repart All, All Range, Selected Range. Display Type:TFT colour display with white LED-backligh, Sound effects: Direct Source (Direct), 10-Band Equaliser, DSEE HX, DC Phase Lineariser, Dynamic Normaliser, ClearAudio+, Vinyl Processor. Built-in rechargeable lithium-ion battery, Wi-Fi 2.4/5 GHz. |
| 1485 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1486 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 2.5 Sqmm (80/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. |
| 1487 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1488 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1489 | Supply, Installation,Testing & Commissioning of 6 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1490 | Reception at Ground Floor Supply, Installation, Testing and Commissioning of 55" LCD panel with 3840 X 2160 resolution or better, USB playback,bluetooth and meracast connectivity,4X HDMI 2.0,DP1.2, HDR10,500 nits or better, Video wall mode should be available, contrast ratio : 1200:1, OPS slot,should have 178 degrees viewing angle complete with mounting and accessories. |
| 1491 | Supply, Installation, Testing and Commissioning of digital signage player with flawless 4K and Full HD single video decoding, mainstream HTML5 performance and simultaneous playback from local, networked and streaming sources. Includes the standard I/O package of gigabit Ethernet, Video Codecs for 4K content: H.265/H.264, Video Containers for 4K H.265/H.264 content: .ts, .mov, .mp4 , Video Codecs for Full HD: H.265, H.264(MPEG-4, Part 10), MPEG-2, MPEG-1, Video Containers for Full HD: .ts, .mpg, .vob, .mov, .mp4, .m2ts, Images: BMP, JPEG, PNG, Audio: MP2, MP3, AAC, and WAV (AC3 is passed through). 4K resolutions: 4096x2160, 3840x2160, 3840x600. Shall have Built-in/external Storage of 8 GB and expandable up to 2TB. |
| 1492 | Supply, Installation, Testing and Commissioning of 6 ft Premium High Speed HDMI Cables with Ethernet, Full 18 Gig HDMI 2.0 4K@60Hz and HDR Certified by HDMI ATC. Should Support Ethernet, ARC, CEC, and all HDMI Audio formats. NEC CM, CEC CMG FT4, RoHS/REACH Compliant, Complete with standard accessories as required. |
| 1493 | Supply , installation , testing and commissioning of Ceiling Flush Music/PA Loudspeaker, Free field Frequency range (-10dB) of 84Hz to 19kHz; Power handling of 64 Watt peak; Nominal dispersion of 140° Conical; Free field Sensitivity of 86 dB SPL and Max SPL of 104 dB SPL peak; Nominal Impedance 16 Ohms; Integral multi-tap Transformer with tap settings of 2/4/8/16 W @ 100V. with Powder-coated steel grille; Shall include necessary standard hardware for ceiling install. |
| 1494 | Supply, Installation, testing and commissioning of intregrated high impedence Class D zone amplifier with output power of upto 90W @ 70/100V. frequency response of 50Hz to 20kHz; THD <0.3%; Shall include priority override and Fire alarm interface, shall include necessary loudspeaker EQs. |
| 1495 | Supply, installation, testing & Comissioning of 2 Zone Controller cum Volume Control, type: Passive controller, linear potentiometer 0- 10 k? and 4-position switch, One RJ-45, TIA/EIA 568B wiring standard connector complete with standard accessories as required. |
| 1496 | Supply, installation, testing & Comissioning of Audio input plate having XLR/AUX input to connect the local source. |
| 1497 | Supply, Installation, Testing and Commissioning of Category 6A F/UTP EN Series 23 AWG 4 Pair Shielded Cable. Solid annealed bare copper conductors, High density polyethylene insulation, 4 pairs twisted in varying lays and cabled, Overall aluminum/poly foil shield with drain, Flame rated PVC jacket, TIA/EIA-568-C Category 6A, NEC CMR, CEC CMR FT4, RoHS compliant. |
| 1498 | Supply , installation , testing and commissioning ofWorkstation with i-7 Configuration. Server: Intel Core i7, such as Intel Core i7-4770 Quad-Core 3.4Ghz 8 GB DDR3-1600 RAM 1 Gbit/s Network Hard drive SATA 6 Gbit/s 7200 RPM Enterprise Class – Up to 48 Mbps per drive for optimal performance. Client: Intel Core i7, such as Intel Core i7-4770 Quad Core 3.4Ghz 8 GB DDR3-1600 RAM , Bandwidth supported - Up to 256 Mbit/s video data. Should include Keyboard and Mouse and 21.5" FHD Monitor. Should Include Signage software with customized GUI, Window 10.or its equivalent in specifications |
| 1499 | Supply, Installation, Testing and Commissioning of 24-port 1000base-T Gigabit PoE+ Smart Managed Switch. . Should have Network Protocol and Standards Compatibility IEEE 802.3 Ethernet. IEEE 802.3i 10BASE-T.IEEE 802.1x. complete with standard accessories as required. |
| 1500 | Supply, Installation, Testing and Commissioning ofSpeaker Cable – 1.5 Sqmm (48/0.20mm) x 2 core cable ATC copper conductor PVC insulated, core twisted, outer jacketed with Vasiform Type PVC Sheath. |
| 1501 | Supply, Installation, Testing and Commissioning of 18 AWG microphone cable (24/0.20mm) x 2 core ATC copper conductor, PE insulated, core twisted in a circular form, Inner sheathed with moisture Proof Polymer, braid shielded (80%) with ATC copper, outer Jacketed with Matt finish Rugged Flexible PVC. |
| 1502 | Supply, Installation, Testing and Commissioning of bulk connectors XLR, RJ-45, Speakon, Phono, Stereo Jack etc as required. |
| 1503 | Supply, Installation,Testing & Commissioning of 6 U Equipment rack to house all rack mountable equipment, with internal wiring, front glass door,heat dissipation fans,power distribution units etc.complete with standard accessories as required. |
| 1504 | Supply, installation, testing and commissioning of 55" 4K Hospitality Display Panel - 55", 4K - UHD, Android Display, HDMI, USB, LAN, 20W SPK, Wifi, Hotel Mode, HDMI CEC, Web with atleast one year standard warranty. Make : Sony |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
