|
| 1 | Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete,brick work,masonary etc. any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 2 | Dismantling of any type fencing, chain link or barbed wire fencing & wire mesh etc complete all as specified and directed. |
| 3 | Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, and removing surplus soil to a distance n.exc 50 m in soft/ loose soil complete all as specified and directed. |
| 4 | M&L PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass complete all as specified and directed. |
| 5 | S&F mild steel work in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) plain MS bars etc including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 6 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provission of binding wire complete all as specified and directed. |
| 7 | Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and directed. |
| 8 | M&L preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 9 | M&L preparation of new steel surfaces of any description not ec 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 10 | M&L mild steel round bars 10mm dia and over, cut to length, bent to shape required, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to Gde E-165 (Fe-290) complete all as specified and directed. |
| 11 | Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exc 5cm but n exc 10cm long Dia meter of Shank 5 to 10 mm |
| 12 | S&F in repairGalvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) |
| 13 | Demolition brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. |
| 14 | M&L Brick work with old size flyash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed. |
| 15 | M/L providing, cement concrete Type B1 1:2:4 (12.5 mm graded aggregate) in in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not proivded for in Item 159, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete all as specified and directed. |
| 16 | Providing precast cement concrete block or slab Type C-1 using 20mm graded stone aggregate and set in CM(1:4)in window or door cills, intels, bressumers,steps,quoin blocks (foruse with masonry),string courses,copings .kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets,etc. (of any section indicated), with plain fair faces,including hamfers, weatherings , throating etc. and setting in mortar complete with joints to match complete all as specified and directed. |
| 17 | M&L forprecast louvres and jallies, in cement concrete 1:2:4 type B 0 using 12.50 mm graded crushed stone aggregate set in CM 1:6, 35 mm thick (measured solid), including all mould- ings but excluding frame including dismantling old cement concrete jalli complete all as specifiedand directed . |
| 18 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 19 | Preparing new plastered surfacesand applying two coats of cement base paint over one coat of primer complete all as specified and directed. |
| 20 | Site clearance incl clearance of shrubs,vegetation, grass, bush, weed, and rubbish/useless materials disposed off upto a distance 50 m outside the periphery of the area complete all as specified and directed. |
| 21 | Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 22 | M&L Welding in repairs n. exc 2.5cm in length and thickness of metal n.exc 6mm ,including for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, as required complete all as specified and directed. |
| 23 | M&Lfor Running welding in repair ,thickness of metal to be weldd is n.exc 6mm ,including for cleaning and preparing the surfaces to be welded together, holding the members in true position while welding and bevelling of edges, as required complete all as specified and directed. |
| 24 | Cutting holes in brick walls up to depth exc one brick but n.exc two brick , built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed. |
| 25 | Taking down and refixing the steel gate by using mechanical hydraulic equipment, Area of eachdoor/gate isexc 05 sqm butn.exc 15 sqm to carryout greasing, oiling,repair of damage hinges and pintals, straighting of steel member like angle, Tee, chanle etc , ms sheet, welding if any required, changing of any damge part required for proper functioning of gateincluding to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 26 | Taking down and refix the steel gate by using mechanical hydraulic equipment, Area of eachdoor/gate is exc 15 sqm butn.exc 25 sqm to carryout greasing, oiling,repair of damage hinges and pintals, straighting of steel member like angle, Tee, chanle etc , ms sheet, welding if any required,changing of any damge part required for proper functioning of gate including to carry out one coat of synthetic enalmal paint and preparation of steel surfacein all respect,complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 27 | Taking down and refix the steel gate by using mechanical hydraulic equipment, Area of eachdoor/gate is exc 25 sqm butn.exc 40 sqm to carryout greasing, oiling,repair of damage hinges and pintals, straighting of steel member like angle, Tee, chanle etc , ms sheet, welding if any required,changing of any damge part required for proper functioning of gate including to carry out one coat of synthetic enalmal paint and preparation of steel surfacein all respect,complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 28 | S&F 0.63mmMild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred complete all as specified and directed. |
| 29 | Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 05 sqm butn.exc 10 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , ms shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified anddirected. Note:-(i) Any part of rolling shutter if required be changed shall be measured and paid seperately under relevent item. |
| 30 | Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 10 sqm butn.exc 15 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , ms shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 31 | Taking down top cover of rolling shutter and refix the same, Area of rolling shutter is exc 15 sqm butn.exc 20 sqm to carryout greasing, oiling, repair of damage laths & hinges, spring,pully , ms shaft, bearing etc,straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 32 | Taking down top cover androlling shutter and refix the same of any size and patteren, tocarryout greasing, oiling, repair of damage laths & hinges, spring,pully , ms shaft, bearing etc, straighting of steel member if requird, welding if any required, changing of any damge part required for proper functioning of rolling shutter including to carry out one coat of synthetic enalmal paint and preparation of steel surface complete all as specified anddirected. Note:-(i) Any part of steel gate/door if required be changed shall be measured and paid seperately under relevent item. |
| 33 | Supplyonly Ball bearing for rolling shutters of any size complete all as spcefied and directed. |
| 34 | Supplyonly MS pipe 50mm dia for rolling shutters of any size complete all as spcefied and directed. |
| 35 | Supply only MS pully suitable for rolling shutter of any size complete all as spcefied and directed. |
| 36 | Supply only MS gear box suitable for rolling shutter of any size complete all as spcefied and directed. |
| 37 | Supply only MS Spring suitable for rolling shutter of any size complete all as spcefied and directed. |
| 38 | Supply only MS sliding lock suitable for rolling shutter of any size complete all as spcefied and directed. |
| 39 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically providedcomplete all as specified and directed. |
| 40 | M & L for 50mm thick cement concrete type C – 1 (1:3:6) using 20mm graded stone aggregate as in plinth protection and PCC paved area, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 41 | Taking down cement plaster incl racking out joints, hacking for key & scrubbing down with water etccomplete all as specified and directed. |
| 42 | M&L, 15mm thick rendering in CM 1:4 to brick/conc wall surfaces trowelled to even & smooth w/o using extra cement. Including complete all as specified and directed. |
| 43 | M & L two coat of cement base paint on newsurfaces of walls including preparation of surfaces completeall as specified and directed by Engineer-in-Charge . |
| 44 | M & L one coat of cement base paint on old or newsurfaces of walls including preparation of surfaces completeall as specified and directed by Engineer - in - Charge . |
| 45 | S&F 16 to 18mm thick Dholpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with 15mm thick cement ans stone dust mortar, recess pointed(10mmx20mm) and with admixter of white cement and dholpur stone dust (1:1) using adihisive and including one number SS clamps (grade -202) of flat 30mm X 2mm,150mm long made to shape in each slab,making V groove at top and bottom of stone and drilling hole for hold fastener,polishing, rubbing &including silicon treatment including dismantling old stone cladding complete all as specified and directed. |
| 46 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over oldsurfaces including complete removal of existing treatmentcomplete all as specified and directed. |
| 47 | Complete removal of existing treatment on walls and roughening surfaces of old plaster by picking sweeping clean and washing down with water to remove dust etc to recceve rough plastercomplete all as specified and directed. |
| 48 | M&L for 10mm thick cement plaster in CM 1:4 as in backing coat for rough plastercomplete all as specified and directed. |
| 49 | M&L for Rough cast plaster with rough mixture consisting of crushed stone or fine gravel agg, size 6 to 12mm mixed with course sand and cement in the ratio of 1:1:1 shall be applied and finished even on external wallcomplete all as specified and directed. |
