Tender For Construction Of 1 (One) No. Switch Room Cum Chlorine Room (4.88M X 3.66M) Including Sanitary Arrangement As Per Departmental Drawing At The Site Of Sambhunagar W/S Scheme, Block - Gosaba Under Canning Sub-Division Of Alipore Division, Phe Dte
Tender Value
8.57 Lakhs
Estimated cost
Bid Submission
09 Feb 2024
0 days left
EMD
17142
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
gosaba → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of 1 ( One ) No. Switch Room Cum Chlorine Room ( 4.88M X 3.66M ) Including Sanitary Arrangement As Per Departmental Drawing At The Site Of Sambhunagar W / S Scheme, Block - Gosaba Under Canning Sub-Division Of Alipore Division, Phe Dte.
BOQ
| Sl. No. | Item Description |
| 1 | Earth working excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding latarite or sands stone) including removing , spreading or stacking the spoils with in lead of 75 mtr. as directed the item includes necessary trimming the sites of trenches, leveling dressing, and ramming the bottom, bailing out water as required complete.a) Depth of excavation not exceeding 1500 mm. |
| 2 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powered earth or local sand. |
| 3 | Cement Concrete with graded jhama khoa (30 mm size) excluding shuttering.a) 6:3:1 proportion in ground floor. |
| 4 | Ordinary Cement concrete (mix 1:1.5:3) with graded stonechips (20 mm nominal size) excluding shuttering andreinforcement if any, in ground floor as per relevant IS codes. |
| 5 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 6 | Brick work with 1st class bricks in cement mortar (1:6) |
| 7 | a) In foundation and plinth |
| 8 | b) In superstructure ground floor. |
| 9 | Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete.a) with earth obtained from from excavation of foundation. |
| 10 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation, basement and upto roof ofground floor/upto 4 m. |
| 11 | i) Tor Steel/Mild Steel. (Other than SAIL/ TATA/ RINL) |
| 12 | Hire and labour charges for shuttering with centering and necessary staging upto 4 mtr. using approved stout props and thick hard wood planks of approved thickness with required with required bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting, fixing & striking out after completion of works(Upto roof of ground floor)a) 25mm to 30mm thick wooden shuttering as per decision & direction of Engineer-in-charge. |
| 13 | 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer\"s specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost ofwater proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item NO 60, polymer based paint as per item 59 (a) of Section (C) |
| 14 | 125 mm thick brick work with 1st classbricks in cement mortar (4:1) in ground floor. |
| 15 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening ofconcrete surface and applicationofcement slurry before flooring works using cement @ 1.75kg/sq.m all complete including all materials and labour.In ground floor.3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).Using grey cement |
| 16 | i) 25mm thick. |
| 17 | Neat cement punning average 1.5mm thick in wall, dado,window, ceiling, floor, drain etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 18 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).i) With 6:1 Cement mortar. |
| 19 | a) 20 mm thick toinside wall |
| 20 | b) 15 mm thick plaster at outside wall |
| 21 | ii) 10 mm thick (4:1) |
| 22 | Woodwork in door and window frame fitted and fixed in complete including a protective cost of painting at the the contract surface of the frame excluding cost of concrete, iron but hinge and MS clamp (The quantum should be concreted upto three decimals) a) Sal (Local) |
| 23 | Panel shutter for door and window as per design (Each panel consisting of single plank without joint) including fitting and fixing the same in position but excluding the cost of hinge and other fitting in Ground floor (in case of non supply of single plank, panel rate of reduction of 20% will be made) ii) 35 mm thick with 19mm thick panel. of size 30 to 45cm.a) Gamar/Champ/Badam/Bhola/Hallak |
| 24 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor)(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr |
| 25 | Acrylic Distemper to interior wal, ceilng with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specifcation) including cleaning and smothning of surfacei) Two Coats |
| 26 | Aplying Exterior grade Acrylic primer of aproved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(mat finish) or smoth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specifcation and as per direction of the EIC.In Ground Flor:a) One coat. |
| 27 | Protective and Decorative Acrylic exterior emulsion paint of approvedquality, as per manufacturer\"s specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidentalcharges but excluding the cost of primer.In Ground Flor:a) Two coat. |
| 28 | a)Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc. |
| 29 | b) Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc. |
| 30 | Painting with best quality synthetic enamel paint of approved made and brand including smoothening surface by sand, paperingetc.including using of approved putty etc. on the surface if necessary. a) On timber or plastered surface with other than hi gloss of approved quality.I) two coats. (With any shade except white) |
| 31 | b)On steel or other metal surface with other than hi gloss of approved quality. I)2 coats.(With any shade except white) |
| 32 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) (b) 40mm X 6mm, 200mm Length |
| 33 | Anodized aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S.205/66) and fitted and fixed with cadmium plated screws : |
| 34 | a) 75 x 63 x 3.2mm |
| 35 | b) 100 x 75 x 4.0mm |
| 36 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:a) 100 mm grip x 10 mm dia rod. |
| 37 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: |
| 38 | a) 300 mm long x 10mm dia bolt. |
| 39 | b) 150 mm long x 10mm dia bolt. |
| 40 | Iron hasp bolt of approved quality fitted and fixed complete oxidized with 16mm dia rod withcenter bolt and round fitting. a) 300mm long. |
| 41 | Supplying, fitting, fixing wooden cleat (Sal or Teak as required) with hinge and steel screw with 50mm iron butt hinges Local |
| 42 | 12.5cm long buffer block (Sal or Teak as required) |
| 43 | Number of Plaque of buildings (Plaque size upto 225mm x 225mm) made of cement plaster (2:1) on face of wall of plinth, with 50mm size letters P.H.E. and the number of the structure formed thereon (in sunk type) including painting the letters complete as per direction. |
| 44 | Construction of septic tank of dif erent capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two560 mm dia. R.C.C. manhole cover (heavy type) of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C (1:1.5:3) bottom slab including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,PartI.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. With Pakur Variety : (Other Manufactures not Specified) |
| 45 | i) For 10 users |
| 46 | Orissa pattern water closet in white glazed Vitreous chinaware of approved make supplied, fitted fixed in position complete excluding P or S Trap. (Excluding cost of concrete for fitting) i) 530mm x 410mm |
| 47 | Supply of UPVC Pipe (b Type) & fitings conforming to IS-13592-1992 |
| 48 | (A) (i) Single Socketed 3 Meter Length(a) 75 mm |
| 49 | xxi)110 x 110 P Trap, 75 mm |
| 50 | Construction of circular soak well 2.5 metre deep in all types of sandysoils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top ofthe R.C.C. cover slab including filling bottom 1.00 metre ofinside ofthe well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia[For other Manufactures not Specified] |
| 51 | Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) of size 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut at junction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mm M.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to be provided as gap insert. The door frame to be fixed with wall by using 8mm dia. and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos. screws to be provided for each vertical member & 2 nos. for horizontal member all complete as per direction of Engineer-in-Charge.(a) Plain Colour. |
| 52 | Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular \"L\" shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete. |
| 53 | Supplying PVC water storage tank of approved quality with closed top with lid (Black) - Multilayer.a) 500 ltr. Capacity. |
| 54 | Supplying, fitting and fixing PVC pipes of approved makeof (mediumduty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) a) For Exposed WorkPVC Pipes(Dia)15 mm |
| 55 | 25 mm. |
| 56 | Labour for hoisting plastic water storage tank. |
| 57 | (i) Upto 1500 litre capacity |
| 58 | (a) Upto 1st story from G.L. |
| 59 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 60 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR whiteflexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. |
| 61 | (i) 600 mm long |
| 62 | Supplying, fitting and fixing porcelain soap tray of approved make. |
| 63 | (i) Recessed soap tray of size 150 mm X 150 mm |
| 64 | Supplying, fitting and fixing towel rail with two brackets. |
| 65 | (a) C.P. over brassi) 25 mm dia. and 600 mm long |
| 66 | Supplying, fitting and fixing bib cock or stop cocki) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO /ATLAS or equivalent)15 mm |
| 67 | Earth work in filling in compound tank, low land, ditches etc. with good earth in layers not exceeding 150mm including breaking clods and consolidating the same ramming and dressing complete (With carried earth arranged by the contractor within a radius exceeding 3 km. but not exceeding 5km. including the cost of carried earth.) |
| 68 | Supplying, fitting and fixing bib cock or stop cocki) Chromium plated angular Stop Cock with wall flange (Equivalentto Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 69 | Supply lock with key. |
| 70 | Add @22.5 % riverine except item no. 1,5,7 & 45 i.e. Rs.549185.30 |
| 71 | Add @18% GST except item no. 1,5,7 ,45 & 47 i.e. Rs. 672351.99 |
| 72 | Add @18% GST on item no. 1,5,7 ,45 i.e; on Rs. 46473.71 |
| 73 | Add @1% Cess except item no. 47 Rs. 848214.32 |
AI Tender Summary
Tender Timeline
Jan 22, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 09, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 12, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender