Tender For Constructions Of 4 No Ranney Wells, Laying Of Rising Main, Construction Of Mbs At Village Chandhat And Janacholi For Augmentation In Water Supply In Palwal And Nuh And All Other Work Contingents Thereto.
Tender Value
161.10 Crore
Estimated cost
Bid Submission
02 Feb 2024
0 days left
EMD
3.22 Crore
Bank guarantee accepted
Document Fee
50000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
mandkola → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Constructions Of 4 No Ranney Wells, Laying Of Rising Main, Construction Of Mbs At Village Chandhat And Janacholi For Augmentation In Water Supply In Palwal And Nuh And All Other Work Contingents Thereto.
BOQ
| Sl. No. | Item Description |
| 1 | Provision for Acquisition of land for Construction of Ranney Well. 4 No. Ranney Well village Chandhat 1.5 acre each Each Ranney Well = 4 No. x 1.5Acre = 6 Acre4 No. Approach path village Chandhut 2 acre each Path = 4 No. x 2 Acre = 8 AcreTotal = 6 acreplus8 acre = 14 Acre |
| 2 | Provision of Supplying and Fixing Fire Fighting equipment |
| 3 | Automation of various electrical installation with control room centre at main water works lumpsump |
| 4 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14SWG, CRCA sheet |
| 5 | Wiring and Cabling Complete wiring and cabling as per detailed specificationsi) From control panel to starter 2 x 3 core x 200 sqm runs of armoured. |
| 6 | Wiring and Cabling Complete wiring and cabling as per detailed specificationsii) Starters to motors 1 x 3 core x 200 sqm to armoured. |
| 7 | Earthing Double loop earthing for all electrical equipment from the existing grid as per electricity rules with 5 Nos. earth pipe complete |
| 8 | Pipes and Fittings Providing laying jointing and testing M.S. D/F pipes made of M.S. sheet confirming to IS: 2262 welded as per IS: 816 pipes IS standard, valves and specials required for suction and delivery pipes including testing etc. complete in all respect. |
| 9 | Supply and erection of Hand operated Travelling crane with Trolley and Chain Block complete 3 tonne capacity |
| 10 | Sump Pump Provision for Supply and Erection of Sump Pump, Dewatering pump and vacuum pump complete |
| 11 | Providing and Installation of flow meter suitable to measure discharge 750 cum./hr to 2000 cum/hr |
| 12 | Cost of Fire fighting equipment |
| 13 | Cost of Street light at site |
| 14 | Wiring and CablingComplete wiring and cabling as per detailed specifications i) From LT control panel to motors and others |
| 15 | Earthing Double loop earthing for all electricalequipment from the existing grid as per electricity rules with 4 Nos. earth pipe complete |
| 16 | Pipes and Fittings Providing, laying, jointing and testing C.I. D/F pipes, valves and specials requiredfor suction and delivery pipes including testing etc. complete in all respect |
| 17 | Providing and Installation of flow meter suitable to measure discharge200mm i/d |
| 18 | Providing and Installation of flow meter suitable to measure discharge150mm i/d |
| 19 | Cost of Fire fighting equipment (Detail attach) |
| 20 | Provision for Electro chlorinatory system |
| 21 | Supplying and fixing of Sluice Valves, Kinetic air valves, Zero Velocity valves along with contingent material required for their fixing with pipes and specials complete in all respect as per specification and direction of the Engineer-in-charge of rating Pn 1.6 (b) Supplying and fixing of 600mm i/d Zero velocity valve rating PN 1.0 fixing on 800mm i/d DI K-9 pipe line including construction of manhole chamber complete in all respect on Engineer-in Charge |
| 22 | Reinforced cement concrete 1:2:4 with stone aggregate 20mm nominal size for thrust block bearing block and pipe and casing under roads including placing in position shuttering etc. complete in all respect. |
| 23 | Supplying, laying ,jointing, fixing and testing G.I pipe linesa) 15mm i/d |
| 24 | SCADA and Networking software Development, Implementation and Testing |
| 25 | Coating of outer surface of casing pipe with P.U coating to dry film thickness 1500 micron for protection against corrosion complete in all respects. |
| 26 | Providing and fixing aluminium glazedwindows in pump house circular wall 230mm thick and Providing and fixing steel glazed doors in pump house circular in all 230mm thick and windows and ventilators in sub station including frames complete in all respect . |
| 27 | Providing and welding non return sand valve in position in the first slotted pipe to be derived in the strata |
| 28 | Fabricating, providing and erection a steel ladder in the well with properly painting. Length 25m |
| 29 | Providing and fixing 25mm dia GI medium class pipe for railing in two rows to be measure in meters, complete with labour and materials |
| 30 | Supply and erection of LT switch gear controlpanel at clear water pumping station includingof main incoming ACB from transformer,individual switch as for pumps motors, startersetc. complete with all instruments required forincoming or outgoing feeders. (Panel board for4 Nos. motor) with Flat and boost chargingbattery charger of 80 AH capacity 30 VDCwith battery, leads complete and otheraccessories for battery and charger with gaugecomplete in all respect as per specification |
| 31 | Supply and erection of complete set of 400mmi/d D/F M.S. pipe, sluice valve, NRV, scourvalve and chambers, pipe should be flangedjointed with nuts and bolts and rubber packingetc. for individual delivery and interconnectionof above pumps in common header completein all respect |
| 32 | Supply and fixing of pressure gauge in thedelivery of each pump and one in commonfeeder with all fittings complete in all respect |
| 33 | Electronic water level indicator digital typecomplete in all respect . |
| 34 | Supply and fixing of armoured power cable,with earthing complete suitable for 4 Nos.pumping plant complete in all respect andcable from the outgoing feeder MCC to.. |
| 35 | Supply and fixing of 5 tons capacity HOTcrane to suit the pump house complete in allrespect including side girder with square baretc. complete in all respect ... |
| 36 | To carry out the foundation work at the DGroom and Providing and fixing of M.S. Tank1000 ltr. Capacity for storage of dieselcomplete in all respect .. |
| 37 | Cost of testing and commissioning of allMechanical and Electrical components forproper functioning of the Ranney Well.. |
| 38 | Providing complete instrumentation telemetryas required for Scada at ranney well withinstrumentation at Public Health EnigneeringDepartment Office.. |
| 39 | Supplying and fixing of Sluice Valves, Kinetic air valves, Zero Velocity valves along with contingent material required for their fixing with pipes and specials complete in all respect as per specification and direction of the Engineer-in-charge of rating Pn 1.6 cc) Supplying and fixing of 150mm diaKinetic Air Valve rating PN 1.6 with all piping for fixing on 800mm i/d DI K-9 pipe and Tee including construction of manhole chamber complete in all respect as per the specification and direction of Engineer-in-charge |
| 40 | SSupplying and installing 200mm i/d scour arrangement on 800mm DI K-9 pipes including cost of 200mm i/d sluice valve of IVC/Kirloskar make and all jointing tests and valves etc. and cost of construction of manhole chamber complete. |
| 41 | Supply and fixing of Sluice Valves IVC / Kirloskarmake 700mm i/d |
| 42 | Supply and fixing of Sluice Valves IVC / Kirloskarmake 600mm i/d) |
| 43 | Supply and fixing of Sluice Valves IVC / Kirloskarmake 400mm i/d) |
| 44 | Supply and fixing of Sluice Valves IVC / Kirloskarmake 300mm i/d |
| 45 | Supplying, laying ,jointing, fixing and testing G.I pipe linesb) 20mm i/d |
| 46 | Supply, fixing ,and jointing G.M valve/gate valve(Heavy pattern)a) 20mm i/d |
| 47 | S and F PVC waste pipe for WHB complete.. |
| 48 | Providing and fixing in position 40mm dia PVC waste pipe up to floor level complete... |
| 49 | Supply and fixing of VCB 24 volts Deiperated as per DHBVN requirement complete... |
| 50 | Providing and Installation of ` casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 7200 Lpm 35 M Head with 95 HP motor.. |
| 51 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14 SWG, CRCA sheet. |
| 52 | Supply and erection of Hand operated Travelling crane with Trolley and Chain Block complete 2 tonne capacity.... |
| 53 | Providing and Installation of ` casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 145 Lps 35 M Head with 115 HP motor.. |
| 54 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14 SWG, CRCA sheet.. |
| 55 | (i) Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect.i) 255 lps with 35 M Head (200 BHP) |
| 56 | Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 195 lps 35 M Head with 155 HP motor.. |
| 57 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14 SWG, CRCA sheet... |
| 58 | Provision for Supply and Erection of Sump Pump, Dewatering pump and vacuum pump complete... |
| 59 | Providing and Installation of ` casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 120 Lps 35 M Head with 95 HP motor.. |
| 60 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14 SWG, CRCA sheet |
| 61 | Supply and erection of Cubical type L.T. Panel board, having independent incoming and outgoing feeder, fabricated from 14 SWG, CRCA sheet.... |
| 62 | Providing and casting of Grade M-30 reinforced cement, concrete as per mix design approved by Engineer-in-charge with minimum cement content 400kg/M3 with shuttering vibrating, curing etc. complete . |
| 63 | Supply and erecting of vertical turbine, wet pit and water lubricated type with under ground discharge elbow clear water pump with suitable coupling complete in all respect having the following capacities. The pump stool to be compatible with the motor. The pump should be providing with ratchet. So that shaft cannot rotate in reverse direction. 2700 LPM 30m head (30 BHP MOTOR) |
| 64 | Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 120 lps with 55 M Head (150 BHP) |
| 65 | Providing and Installation of ` casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 170 Lps 35 M Head with 135 HP motor.. |
| 66 | lying and fixing openable anodized (15 micron) aluminium doors and windows |
| 67 | SRP coating |
| 68 | Supply and erection of street light luminaire minimum IP - 65/66 level protected single piece dia cast almunium / almunium sheet housing with pot optic reflector, heat resistant glass cover or HPSV lamp complete with copper wound blast capacitor complete.(iii) Sodium 250 W Street light luminator |
| 69 | -Providing earth/ sand back fill compacted including laying earth as per specification for compaction in 25cm layers, dressing, watering and rolling the earth laid in 25cm layers as per Specification for compaction complete in all respects.a.for R/wellb.FOR APPROACH PATHC.FOR RASTA |
| 70 | Supply and placing in position coarse Yamuna sand to be filled under road cuts and around thrust block of M.S. specials as per direction/instructions of the Engineer - in -charge. |
| 71 | Supply, erection, testing and commissioning of lighting fixtures and poles for inter lighting and fixing arrangement and recessed conduits cables and recessed. based alongwith piano type switch, plug point etc. complete in all respects including trench with pipe (M.S. pole 11 M height with 100 w led light. |
| 72 | Supply, Erection,testing and commissioning ofPuffin 18W White Round Bright LED Panel LightCeiling Downlight Lamp Kit with LED DriverSurface Mount LED Ceiling Light (Pack of 1)(2Year Warranty Make:-Philips,Bajaj,GE,Wipro,K-lite,cromptongreaves |
| 73 | Supply and erection of complete set of 400mm i/d D/F M.S. pipe, sluice valve, NRV, scour valve and chambers, pipe should be flanged jointed with nuts and bolts and rubber packing etc. for individual delivery and interconnection of above pumps in common header complete in all respect |
| 74 | Supply and fixing of pressure gauge in the delivery of each pump and one in common feeder with all fittings complete in all respect |
| 75 | Electronic water level indicator digital type complete in all respect . |
| 76 | Supplying and fixing of Sluice Valves, Kinetic air valves, Zero Velocity valves along with contingent material required for their fixing with pipes and specials complete in all respect as per specification and direction of the Engineer-in-charge of rating Pn 1.6 (aa) Sluice valve 800mm i/d including cost of chamber etc. complete. (Make IVC/Kirloskar) |
| 77 | Supplying fixing, testing and commissioning IVC make D.I recoil non return type zero valve having body in D.I to IS 1865 Gr. 400/15, Slant seat design, PN-1.6 rating flanges to be drilled as per IS: 1538 complete in all respect to the satisfaction of Engineer-in-charge. |
| 78 | Supplying fixing, testing and commissioning M.S D/F pipe for scouring arrangement complete in all respects to the satisfaction of Engineer-in-charge. 250mm i/d |
| 79 | Providing under reamed cast in situ piles using controlled concrete grade M-30 designed mix, 6.5m deep including boring and getting out the soil and disposal upto a lead of 100 m including cost of steel reinfocement, jointing the tiles with main bar with welding and also all T and P retuined completed in all respect the code followed 400 mm dia under reamed. |
| 80 | Supply and painting 2 coat of shalpoxy CTC (LB) type coalar epoxy to protect steel structure complete to the entire satisfaction of the engineer-in-charge. |
| 81 | Boring/excavation including making thrust pit and receiving pit to the precise dimensions for the launch of the specialized Auger boring machine in normal soil condition but not in Rock/boulders/any underground utility like foundation, water supply line coming in alignment or other under ground obstruction under KGP express way suitable for M.S casing pipe of following sizes including caution and sign board complete in all respects. i) for 724 mm o/d M.S pipe 12 mm thick casing pipe. |
| 82 | Providing and insertion of M.S Casing pipe (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel plates confirming to IS-2062 of following size including cutting, beveling grinding and radio graphically welding of pipes as per IS-1182 complete in all respect including cartage to site of work and testing. i) for 724 mm o/d M.S pipe 12 mm thick casing pipe. |
| 83 | Providing and insertion of water supply pipe 416 mm o/d M.S pipe 8mm thick (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel conforming to IS : 2062, including inner lining by cement concrete mortar which shall be prepared from aggregates/sand and cement mixed in ratio 2:1 by weight with minimum cement content of 450 Kg/M3 having strengh of 25 N/mm2 after 20 days complete as per IS: 1916-1989 with latest revision, providing roller arrangement for smooth insertion and anchoring of pipe through out the length with HDPE spacers at distance of 2 m apart to aviod contract of casing pipe and carrier pipe including cutting, joining, radio graphically welding as per IS: Hydraullic testing complete in all respects. |
| 84 | Cleaning of surface of M.S pipe (casing pipe and carrier pipe) inner surface and outer by sand blasing at site to make the surface ready for P.U. coating/High built epoxy paint/polythene tap system complete in all respects. |
| 85 | coating of outer surface of casing pipe with P.U coating to dry film thickness 1500 micron for protectio against corrosion complete in al respects. |
| 86 | coating of outer surgace of water carrier pipe with polythene tape system for protection against corrosion complete in all respect. |
| 87 | Coating of inner surface of casting pipe with High built epoxy paint to R.D.S.O. specification no MandC/PCN/111/88 to a dry film thickness of 250 micron. |
| 88 | Providing and fixing H.D.P.E spacer at a distance of 2 m apart to avoid contact of casing pipe and carrier pipe complete in all respect.i) for 724 mm o/d M.S Pipe |
| 89 | Providing concrete block 1:11/2 : 3 on both ends to plug the annular space between casing and carrier pipe including coast of 5mm thick M.S. end plate complete in all respect. i) for 724 mm o/d casing pipe |
| 90 | Ground probe radar survey to check any under ground obstruction before finalizing the alignment. |
| 91 | A) for MBS Chandhat and Janacholi:i) 100 amp. TP E/o ACB equipment with 6no plus 6NC auxilary contacts, 240 volts. AC shur release, service position micro shitwch, 240 V Ac motor ACB will be horizontal draw out type.ii) Earth fault and over current relay of `LT-LK/CandS/BCH` 1 No. iii) automatic power factory connector relay of LT-LK VOMECH, 6 stages- 1 No. IV) 96x96 sqm, mm ameter digital type with 3 nos. CTs and selector switch of range 0-1000 Amp.-1NO.V ) 96x96 sqm voltmeter with volymeter selector switch (0-500v) digital type-1 No. vi) power capacitor bank of suitable rating to improve PF to 0.95 (Wheater one of three pumping opetion) 1 lot.vii) RYB LED indication lamp 1 set.viii) incoming and outgoing cable box-1lot.ix) busbar and suitable cross section for 100 AMPS. for phase and neutral on haif of cross area of main buster-1lot. incoming Feedari) 4 pole, 400 amp. MCCB-3 Nos.ii) 96x96 sqm. ameter digital tupe (0-400 amp.) with 3 nos. CTs selector switch -3 nos. iii) RYB indicating lamps (LED) type-8setiv) 16 Amp. MCB for vaccum pump-2 nos.v) 16 Amp. MCB, for dewatering pump. vi) Dol starter-4 nos. vii) ameter (0.20 amp.) digital type - 4 nos.viii) 16 amp. MCB for lighting and auxiliary load-4 nos.x) soft starter for 110 KW motor- 3 nos. |
| 92 | Supply erection, testing and commissioning of 11KV panel complete as per DHBVN specifications as per approved NIT. |
| 93 | Supply and fixing VCB 24 volts as per DHBVN requirment complete in all respects as per approved. NIT. |
| 94 | Supply, erection, testing and commissioning of HT outdoor cable box XPLE 300 sqm complete in all respect in all respect as per DHBVN specification as per approved NIT. |
| 95 | Supply, erection, testing and commissioning of HT indoor cable box XLPE 300 sqm complete in all respect as per DHBVN specifications as per apporved NIT. |
| 96 | Supply, erection testing and commissioning of HT CT 20/5 amp. complete as per DHBVN specifation as per approved NIT. |
| 97 | Supply, erection testing and commissioning of 11 KV. PT complete as per DHBVN specification as per approved NIT. |
| 98 | Providing chemical earthing with cooper plate as per ISI specification as per ISI specification complete as per DHBVN requirement as per DHBVN NIT. |
| 99 | Boring/excavation including making thrust pit and receiving pit to the precise dimensions for the launch of the specialized Auger boring machine in normal soil condition but not in Rock/boulders/any underground utility like foundation, water supply line coming in alignment or other under ground obstruction under KGP express way suitable for M.S casing pipe of following sizes including caution and sign board complete in all respects. i) for 1340 mm dia per insertion of 1300 mm id M.S pipe |
| 100 | Providing and insertion of M.S Casing pipe (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel plates confirming to IS-2062 of following size including cutting, beveling grinding and radio graphically welding of pipes as per IS-1182 complete in all respect including cartage to site of work and testing. i) for 1340 mm i/d M.S casing pipe 20 mm thick. |
| 101 | Providing and insertion of M.S Casing pipe (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel plates confirming to IS-2062 of following size including cutting, beveling grinding and radio graphically welding of pipes as per IS-1182 complete in all respect including cartage to site of work and testing. i) for1240 mm i/d M.S casing pipe 16 mm thick. |
| 102 | Providing and insertion of water supply pipe 416 mm o/d M.S pipe 8mm thick (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel conforming to IS : 2062, including inner lining by cement concrete mortar which shall be prepared from aggregates/sand and cement mixed in ratio 2:1 by weight with minimum cement content of 450 Kg/M3 having strengh of 25 N/mm2 after 20 days complete as per IS: 1916-1989 with latest revision, providing roller arrangement for smooth insertion and anchoring of pipe through out the length with HDPE spacers at distance of 2 m apart to aviod contract of casing pipe and carrier pipe including cutting, joining, radio graphically welding as per IS: Hydraullic testing complete in all respects. |
| 103 | Coating of inner surface of casting pipe with High built epoxy paint to R.D.S.O. specification no MandC/PCN/111/88 to a dry film thickness of 250 micron. |
| 104 | Providing and fixing H.D.P.E spacer at a distance of 2 m apart to avoid contact of casing pipe and carrier pipe complete in all respect. i) for 724 mm o/d M.S Pipe |
| 105 | Providing concrete block 1:11/2 : 3 on both ends to plug the annular space between casing and carrier pipe including coast of 5mm thick M.S. end plate complete in all respect. i) for 1340 mm o/d casing pipe |
| 106 | Ground probe radar survey to check any under ground obstruction before finalizing the alignment.for 1340 mm o/d casing pipe |
| 107 | Boring/excavation including making thrust pit and receiving pit to the precise dimensions for the launch of the specialized Auger boring machine in normal soil condition but not in Rock/boulders/any underground utility like foundation, water supply line coming in alignment or other under ground obstruction under KGP express way suitable for M.S casing pipe of following sizes including caution and sign board complete in all respects. i) for 1124 mm o/d 12 mm thick casing pipe. |
| 108 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 5-10 meter depth |
| 109 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 10-15 meter depth |
| 110 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 15-20 meter depth |
| 111 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 20-25meter depth |
| 112 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 25-30 meter depth |
| 113 | Providing and placing in position cold twisted bars confirming to IS 1786-1989, for reinforcement including cutting, straightening, bending, binding and placing in position complete including cost of binding wire and wastage etc. complete in all respect . |
| 114 | Providing and casting “in situ Grade M30 reinforced cement concrete mix design as per design mix approved by Engineer-in- charge with minimum cement content 400 kg/m3 for collector well curbs including lowering of steel of well curb in pit and assembling the same in one position as required with necessary shuttering, vibrating curing etc. complete...... |
| 115 | Providing and casting in situ reinforced cement, concrete (1:1.5:3) (1 cement, 1.5 coarse sand 3 stone aggregate) 20-25mm nominal size bottom plug complete of concrete for bottom plug with cement concrete (1:1.5:3) with 10 % excess cement to be laid under still water so that it should be completely water tight when water is pumped out of the well after 15 days ...... |
| 116 | Providing and fixing wooden pattern of porthole in the well steining at G.L. as per drawing at the height of 1.0m above curb and 2.5 m height with fixing vertical circular timer 75mm thick at the end at Ground well before fixing C.I. port holes . |
| 117 | Providing, leveling, fixing with grouting 1:2 mix (1 cement, 2 coarse sand) cast iron port holes with rubber lining 20mm thick properly fixed with adhesive 10 as to have complete leak proof system or as per direction of the Engineer-in-charge of work......... |
| 118 | Supplying and fixing of cast steel bullet head with M.S. tapered rods to CI bullet head and welding to slotted pipes, or as per direction/ instruction of the Engineer in-charge ......... |
| 119 | Supplying and fixing of 350mm dia Sluice valves with the consent of Engineer-in charge of the work, at the well end of the port holes including hand wheel connecting rods, with galvanized bolts, nuts, washers and rubber packing etc. complete job.......... |
| 120 | Fixing of dumy plate of size 400mm dia 10mm thick under water with the help of diver after the completion of driving of laterals .......... |
| 121 | Fabricating, providing and setting out steel curt with steel cutting edge of collector well including placing in position................... |
| 122 | Sinking in fine or coarse sand stone C pebbles, kankar, sand stone gravel clay or mixture of them spreading the same around the well with in a bad of 100 meters 0-5 meter depth |
| 123 | Providing fabrication, fixing, welding M.S. section such as joints, channel, angles plates etc. for pump house floor supporting clamps and electrical motor stool i/c two coats of red oxide or approved point.., |
| 124 | Supply, erection testing and commissioning of 11 KV gang operated air break switch conforming to ISS-2544/1963 with latest amendments suitable of 400 amp. HT load and fitted on the `H` pole complete the job in all respects upto the Engineer- in- charge as per approved NIT.,. |
| 125 | Providing and coating synthetic rubber polymer mixed with cement..,, |
| 126 | Supply and fixing Terra cota tile 25mm thick in wall facing (lining) on wall.. |
| 127 | Cost of supply and erection of CFL/Tube light.. |
| 128 | Supply and installation of KV 3.5 CORE LT cable630 sqm. armoured with termination kit complete in allrespects as per approved NIT.... |
| 129 | (i) Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. ii) 390 lps with 30 M Head (260 BHP) |
| 130 | Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. ii) 245 lps with 40 M Head (220 BHP) |
| 131 | Providing and Installation of Horizontal split casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. ii) 260 lps with 30 M Head (175 BHP) or 130 lps with 55 M Head (175 BHP) as per site condition........... |
| 132 | Porv. and fixing of chequered plates 6 mm thick complete including cutting and welding etc. |
| 133 | Porv. and fixing of chequered plates 6 mm thick complete including cutting and welding etc.......... |
| 134 | Providing under reamed cast in situ piles using controlled concrete grade M-30 designed mix, 6.5m deep including boring and getting out the soil and disposal upto a lead of 100 m including cost of steel reinfocement, jointing the tiles with main bar with welding and also all T and P retuined completed in all respect the code followed 400 mm dia under reamed. |
| 135 | Providing and fixing M.S chequered plates 5 mm thick complete including cost of cutting and welding on steel truss bridge agra canal complete in all respect. |
| 136 | Hiring of heavy duty crane for lifting of truss brideges to place on various crossing including cost of labour, fuel TandP etc. complete in all respects taking working period 2 days deploing of 4 nos. heavy duty crane on both end of bank including insurance of stucture to be placed and workmen executing the work o placing of truss bridge in position as a complete job. up to span of 5- 15 mtr............ |
| 137 | Hiring of heavy duty crane for lifting of truss brideges to place on various crossing including cost of labour, fuel TandP etc. complete in all respects taking working period 2 days deploing of 4 nos. heavy duty crane on both end of bank including insurance of stucture to be placed and workmen executing the work o placing of truss bridge in position as a complete job. up to span of 15- 30 mtr........... |
| 138 | Hiring of heavy duty crane for lifting of truss brideges to place on various crossing including cost of labour, fuel TandP etc. complete in all respects taking working period 2 days deploing of 4 nos. heavy duty crane on both end of bank including insurance of stucture to be placed and workmen executing the work o placing of truss bridge in position as a complete job. up to span of 30-50 mtr. |
| 139 | Boring/excavation including making thrust pit and receiving pit to the precise dimensions for the launch of the specialized Auger boring machine in normal soil condition but not in Rock/boulders/any underground utility like foundation, water supply line coming in alignment or other under ground obstruction under KGP express way suitable for M.S casing pipe of following sizes including caution and sign board complete in all respects. i) for 724 mm o/d M.S pipe 12 mm thick casing pipe..... |
| 140 | Providing and insertion of M.S Casing pipe (Fe-330 grade) fabricated as per IS : 3589 of 1991 from steel plates confirming to IS-2062 of following size including cutting, beveling grinding and radio graphically welding of pipes as per IS-1182 complete in all respect including cartage to site of work and testing. i) for 724 mm o/d M.S pipe 12 mm thick casing pipe........... |
| 141 | Supplying of squirrel cage induction motor SPDP vertical hollow shaft suitable to operate on 415 plus 6 % - 15 % of 650 c/s frequency 3 phase acs supply to operate the above pump of following capacities for 2700 LPM at 30 meter to match with the stool provided with the pump (30 BHP )........... |
| 142 | Providing and Installation of ` casing pumps with squirrel cage induction electric motor including testing commissioning etc. complete in all respect. i) 135 Lps 35 M Head with 105 HP motor. |
| 143 | Cost of Supply and fixing Fire fighting equipment |
| 144 | Cost of Fire fighting equipment |
| 145 | Cost of supply and fixing of Electromagnetic type flow meter 400mm size |
| 146 | Driving slotted M.S pipe radially and horizontally in three layers without rising towards the surface through port holes in any strata and length. Welding each pipe of 1.2 m. If no electricity is available the alternate arrangement will be made by the contractor on their own cost complete. (TATA, SAIL and Jindal) |
| 147 | Fabricating most accurately M.S pipe make out of MS V type sheet 300mm i/d, 316mm o/d x 1200mm long with tapered slots of width 33 mm on outer periphery including cost of 2 coats of paints, the pipe shall have an effective opening area of 16 % (min.) strong enough to with stand pressure of 100 tonnes without buckling complete. (TATA, SAIL and Jindal). |
| 148 | Operation and Maintenance of water works for completescope of work mentioned in the DNIT and of wholeexisting water supply scheme in the village Disinfectionmaterial supplied by the PHED as per schedule-IV for aperiod of 5 years after 12 months during defect liabilityperiod and 3 months trial run period. (will be charged tothe A/mtc estimate) complete in all respects as perapproved NIT. 1) Operation and maintenance duringdefect liability period after 3 month trial run period(operation only) |
| 149 | 1st year Operation and maintenance afterdefect liability period |
| 150 | 2nd year Operation and maintenance |
| 151 | 3rd year Operation and maintenance |
| 152 | 4th year Operation and maintenance |
| 153 | 5th year Operation and maintenance |
AI Tender Summary
Tender Timeline
Jan 19, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 02, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 02, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender