|
| 1 | A. Civil Works:-Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. |
| 2 | Cement concrete 1:8:16 with 40mm gauge stone ballast using concrete mixer volumetric type |
| 3 | First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. |
| 4 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 5 | Reinforced cement concrete M-20 mechanicalymixed using voluemetric type concrete mixer as per IS:1791and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. |
| 6 | First class burnt brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level. |
| 7 | Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. |
| 8 | Reinforced cement concrete M-20 mechanicalymixed using voluemetric type concrete mixer as per IS:1791and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth. |
| 9 | Cold twisted deformed (Ribbed/ Torel Bar) Bars Fe 500 grade as per IS 1786-1985, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete |
| 10 | Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another laver of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of RCC slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing etc. |
| 11 | Cementconcrete1:2:4gola10cmx10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. |
| 12 | Top Khurra 0.6mx0.6m for rain water pipe in 25mm thickcementconcrete1:2:4over50.00 thick cement concrete 1:8:16 |
| 13 | Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3 |
| 14 | Providingandfixing 110mmdia.U.P.V.CRain water pipe of 4kgf./sqmas per IS:4985 includingjointingduringmasonarycompleteas per specificationsand to the entire satisfaction of Engineer-in- charge. |
| 15 | Providingandfixing110mmdia.U.P.V.Cbend forRainwaterpipeasperIS:14735 including jointing completeasperspecificationsandto the entire satisfaction of Engineer- in- charge. |
| 16 | Providing and applying plaster of paris (ISI marked such as JK, Kohinoor, Maharaja etc.) punning 6mm thickness over plastered surface to prepare the surface even and smooth complete in all respect as per the directions of Engineer-in-charge. |
| 17 | 12.5 mm thick cementplaster 1:4 |
| 18 | 20 mm thick cementplaster 1:5 |
| 19 | Base course of floor consisting of 100mm thick cement concrete 1:8:16and 100mm sandfilling (using mechanical mixer for mixing of material) |
| 20 | Providing and laying Vitrified floor tiles 600 x 600mm size premium quality with water absorption less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on either 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand) for new flooring or tile adhesive of approved make (water based) IS : 15477 marked using 5 kg. adhesive per sqm of tile area in average 3mm thickness over existing floor, including grouting the joints with white cement and matching pigments etc.,(Flooring) complete in all respect as per specifcation, drawing andto theentire satisfication of Engineer-In-Charge. |
| 21 | Supplying and fixing of Japani sheet frames (Chowkat) consisting of 18 gauge (1.25mm) thick steel sheet of the specified section (standard design latest), including iron lugs (hold fasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower bolts and finished, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge. |
| 22 | Factory manufactured flush door fixed in positioniron hinges, etc (excluding the cost of any fittingsother than specified above but including labourfor fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 |
| 23 | Cost of aluminmum fittings complete for doors, window, such as tower bolts, handles & screws etc. for these fittings (excluding sliding bolt) complete(i) For single leaf shutter |
| 24 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish |
| 25 | Distempering with Acrylic washable oil bound distemper (of approved manufacture) two coats over one priming coat to give an even shade. |
| 26 | Finishingwallswithacrylic smoothexterior paint of required shade with two or more coats applied@ 1.67litre/10Sqm over and including base coatofwater proofing Cement Paint applied @ 2.20 Kg/10 Sqm |
| 27 | Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fills consisting of white lead, linseed oil Varnish, and Chalk Mitti including finishing the surface to required finishcomplete as per PWD specification 1963 |
| 28 | Painting two coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. With ordinary quality Paint |
| 29 | Providing and laying 60 mm thick cement concrere interlocking paver block of M-35 grade machine maderubber moulded smooth finish by strong vibratory process or with vibro-hydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge for Medium Traffic Areas such as City streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc. |
| 30 | B. Public Health:-(i) Providing Public Health Amenties for Gents and ladies bathroom Excavation manually in trenches for pipe lines with straight or open cuttingin streets and lanes in built up area where width of street / Lane from wall to wall is less than 3 meter including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation, watering , including the cost of dewatering of rain water, diversion for traffic, night signals. Providing & fixing caution boards, watching, fencing, etc. and removal of surplus soil from the site upto 15 meter distance complete in all respects. (a) Earth work upto 1.5 m. Depth(i) All classes of soil except rocky |
| 31 | Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.Type A (a) 160mm o/d SWR UPVC pipe line laid complete |
| 32 | Constructing brick masonry manhole in cement mortar 1:5 ( 1 cement : 5 coarse sand ) R.C.C. top slab 20cm thick using M-20 mix by using mixer and vibrator, TMT Fe500 @ 63.464 kg/per cum, foundation concrete 1:4:8 mix (1 cement: 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making 40mm thick benching in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, Orange coloured PVC steps including RCC cover with frame complete as per standard design complete in all respects. (a) Inside size 75x120 cmwith depth 120 cm between bottom of top slab and invert (with MH cover & frame Medium duty) |
| 33 | Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required.(a) Through wall 11.43 cm thick |
| 34 | (b) Through wall 22.86 cm thick |
| 35 | Cutting holes upto 23cm square for pipes in floor and roofs of cement concrete, reinforced concrete or reinforced brick work andmaking good the same & finishing according to existing finish where required.(c ) Through floor or roof 15.00cm thick |
| 36 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.Single Socket Type A (b) 110mm o/d single socket SWR UPVC pipe lines laid complete |
| 37 | (c ) 75mm o/d single socket SWR UPVC pipe lines laid complete |
| 38 | Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc.as per standard design minimumdepth of water should be 150 mm with a minimum seal 50mm.(b) 100mm internal Diametre H.C.I. gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm |
| 39 | Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, lime concrete with 40 per cent lime mortar 2:3 in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside light duty C.I. inspection chamber cover and frame painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design.(c ) 600mm x 900mm inside with 455mm x 455mm cover and frame medium duty double seal |
| 40 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.D For 75mm o/d pipes(viii) P Trap/Floor Trap 75mm x 75mm |
| 41 | Construction of platform for water storage tank. |
| 42 | Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. (Tripple Layer Tank) |
| 43 | Providing and fixing in position G.I. Tank Nipple of approved make(III) G.I. tank nipple 25mmi/d |
| 44 | Providing and fixing in position automatic brass Ball Cock in tanks.Plastic Ball Cock with rod and Plastic Ball (c ) 20mm i/d |
| 45 | CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacingincluding jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.(b) SDR 11 CPVC pipes & fittings 20mm o/d |
| 46 | (c )SDR 11 CPVC pipes & fittings 25mm o/d |
| 47 | Providing, fixing and jointing Brass Ball valves screwed with SS/BRASS ball & spindle & Teflon seats, on G.I. Pipe lines including all carriages complete.(c ) 25mm i/d Brass Ball valves |
| 48 | Making connection with the existing G.I. branch main up to 40mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing of G.I Tee etc. in the pipe line (including cost of G.I Tee) complete in all respects. |
| 49 | First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth. [4 x 0.6 x 0.11 x 0.7] |
| 50 | Cement Concrete 1:2:4 with stone ballast or shingle. [slabs-0.60 x 3.30 x 0.06] |
| 51 | Base course of floor consisting of 100mm thickcementconcrete 1:8:16and100mm sand filling using mechanical mixer for mixing. [Gents toilet 1.6m x 1.9m & Ladies toilet 1.6m x 1.9m ] |
| 52 | Providing and laying Rectified Porcelin floor tiles 400x400mm or more (thickness to be specified by the manufacturer) of premium quality conforming to IS:15622 of approved make in all colours laid on 20mm thick bed of Cement Mortar 1:4 ( 1 Cement : 4 Fine sand) for new flooring or laid with cement based high polymer modified quick set tile adhesive (water based) of approved make IS 15477 marked using 5 Kg adhesive per Sqm of tile area in average 3mm thickness over existing floor, including pointing the joints withwhite cement and matching pigments etc., complete Gents toilet 1.6m x 1.9m & Ladies toilet 1.6m x 1.9m |
| 53 | Providingandfixing1stqualityceramic glazed wall tiles conforming to IS : 15622 (thicknesstobespecifiedbythe manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 310 x 450 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.Gents toilet2 x 1.6 x 1.5 & 2 x 1.9 x 1.5Ladies Toilet 2 x 1.6 x 1.5 & 2 x 1.9 x 1.5 |
| 54 | Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32 mm dia including cost ofseat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 55 | Providing and fixing jet spray with 2\"-6\" long PVC pipe. (a) With C.P. Brass nut |
| 56 | Providing and fixing partition for different type of urinals Vitreous white Chinaware Partition (i) Small partitionssize 680mm x 300mm |
| 57 | Providing and fixing in position vitreous Chinaware white large flat back or angular lipped front urinal 610 mm highof approved make (to the approval of the Engineer-in-charge)(610 mm x 410 mm x 380mm) consisting of C.P. waste 32 mm dia and C.P. brass spreader, complete. |
| 58 | Providing and fixing PVC waste pipe 32mm complete in all respect. |
| 59 | Providing and fixingin position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge)consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap complete in all respect. (ii) Size 550 mm x 400 mm |
| 60 | Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge)for wash hand basin complete in all respect. |
| 61 | Providing and fixingin positiontowel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.(b) C.P brass towel ring |
| 62 | Providing and fixingin position C.P. brass soap dishof approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect. |
| 63 | Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backingfixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on topcomplete in all respect (as required by the Engineer-in- Charge) (a) Size 600mmx450mm |
| 64 | Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect.(c ) C.P. Brass khunti with 6 pegs |
| 65 | Providing & Fixing in position C.P. Brass extension piece 25mm long to 50mm long of approved make (to the approval of Engineer-in-charge )with various fixtures complete in all respect. |
| 66 | Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect. |
| 67 | Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect.(i) C.P. brass Bib cock long nose/ long body without flange |
| 68 | (ii) C.P. brass Bib cock without flange |
| 69 | Providing & Fixing in position C.P. Brass flange of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. |
| 70 | Making connection of newly laid sewer in walls of existing manhole of fully charge sewer including cost of pluging sewer, desilting, removal of sullage water and making good of khudda(a)Sewer connections upto 300 mm id |
| 71 | Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in |
| 72 | Providing and fixingin position stainless steel sinksof approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect.(a) Double bowl Sink without drain board Overall size 1114 x 490 mm with bowl size 460x385x200mm including waste coupling |
| 73 | Coloured Granite stone tiles 20mm thick in skirting,risersofsteps,dadowallsand pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps. |
| 74 | Providing and fixing in position CP Brass single lever surgical mixer with swinging spout approved make (to the approval of Engineer-in-charge) complete in all respect. |
| 75 | Providing & fixing in position PVC flexible tube connectionof approved make (to the approval of Engineer-in-charge ) complete in all respect.(a) PVC tube connection of size 15 mm x 300 mm with C.P. Brass nut |
| 76 | Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect.(b) C.P.brass 15mm Concealed stop cock with flange. |
| 77 | (c )C.P.brass 15mm Angle valve without flange |
| 78 | Providing & Fixing in postion liquid soap container of approved make (to the approval of Engineer-in-charge ) complete in all respect.(b) Acrylic liquid soap container |
| 79 | Providing and fixing in postion storage type automatic electric water heater pressure type thermostatically controlled, single phase wall mounted of approved make (to the approval of Engineer-in-charge) with thermostats, inner container of stainless steel, Inner glass lining with B-Rating minimum 3 stars complete with 1 Mtr. three core flexible cord with plug, non return valve and pressure release valve complete including fixing and testing complete in all respect.complete in all respect.(ii) 25 litre capacity water heater |
| 80 | (ii) Providing and installing PVC 150mm i/d Tubewell:-Boring with casing pipe for tubewell in all soils except ordinary hard rocks requiring blasting including removing the casing pipe after the tubewell is lowered & tested, equipment as required such as hand boring machine and its accessory, transportation to site and vice versa etc. complete in all respects.(b) Boring with 200 mm i/d Housing pipe. Upto 150 mtr. Depth BGL |
| 81 | Supplying, assembling, lowering and fixing in vertical position in bore well unplastisized PVC medium well casing (CM) pipe of required dia confirming to IS:12818-2010 including require hire and labour charges fitting and accesories all complete for all depth as per direction of Engineer-in-charge.(b) 150mm nominal size dia |
| 82 | Supplying, assembling, lowering and fixing in vertical position in bore well unplastisized PVC medium well screen (RMS) pipe with ribs confirming to IS:12818 including require hire and labour charges fitting and accesories all complete for all depth as per direction of Engineer-in-charge.(b) 150mm nominal size dia |
| 83 | Supplying and fixing MS clamps of size 150mm x 12mm made out of MS flat 1.52 mtr. Long, suitable to fit housing pipe including the cost of nuts & bolts of suitable size complete in all respects. |
| 84 | Supplying at site wooden box of suitable size with lid and locking arrangement for preserving strata sample collectedfrom the bore |
| 85 | Supplying and fixing of PVC Pipe bail plug sutable for 150 mm dia UPVC casing pipe having thicness of sockets as 12mm length 100 mm & base plate of 8 mm thick complete in all respect. |
| 86 | Supplying and fixing MS well cap having thread to fix on housing pipe complete in all respect. (b) 150mm nominal dia meter |
| 87 | Development and stablizing of the Tubewell with Submersible Pump of required capacity as directed by the Engineer-in-charge including the cost of tools, appliances and consumable to the satisfaction of Engineer-in-charge. |
| 88 | Providing, Installing and lowring 1 BHP submercible motor including check valve, steel wire as per guidelines given by Engineer-in-charge complete in all respect. |
| 89 | C. Electrical Works:- RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and CallBell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\" deep for walls and CI 3\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-(ii) Wiring Light Point |
| 90 | (v) Wiring 6 Amp. Plug Control comprising wall socket point. |
| 91 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes(ISI marked) as per IS9537:Part-III &HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-(ii) Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface) |
| 92 | G.I. EARTHING: Earthing with G.I. wire/ rope in G.I. pipe partly recessed and partly on surface complete with 150cm long 50mm dia. G.I. earth pipe (Cutting threads and 36 Nos. holes, 1cm dia. to make a mesh around the GI Pipe) with G.I. reducing socket including erection of the same, 4.50 metre (14.76 feet) below ground level with 20Kg. charcoal & salt mixture etc., up to 8 metre in length (including boring& refilling).(a) Earthing with 8 S.W.G. (4mm dia.) G.I. wire in 15mm dia G.I. pipe with G.I. reducing socket 50mm x 15mm (upto 8Metre in length) |
| 93 | Fixing additional length of earthing with G.I. wire/ rope in G.I. pipe (Flushed in wall and floor) with sockets, elbows and Steel hooks including the cost of cutting and filling up of chases (with finishingthe surface):-(a) Additional length G.I. wire 8 S.W.G. (4mm dia.) in 15mm dia. G.I. pipe (Flushed) |
| 94 | SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.,:-(xxvii) Bakelite Batten Holder (Large size) |
| 95 | MINIATURE CIRCUIT BREAKERS/ RCBO\"s/ RCCB\"s: Supply and erection of Miniature Circuit Breaker MCB\"s for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-(ii) MCB Single Pole 6-32amp. (10kA, Curve-C) |
| 96 | (vi) MCB Double Pole 6-32amp. (10kA, Curve- C) |
| 97 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB\"s/ RCBO\"s/ RCCB\"s: Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO\"s/ RCCB\"s in the distribution board (For SP&N distribution board with provision DP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-(i) SP&N Double Door Distribution Board 4 way each |
| 98 | OVER HEAD DISTRIBUTION ALUMINIUM CABLES, ACSR CONDUCTORS, CLAMPS, JUMPERS & JOINT KITS: Wiring over-head line in PVC insulated & PVC sheathed two single core aluminium conductor cable overall 1100 volts grade binding with G.I. wire 2mm dia. (14 SWG) with brass/ aluminium link clips complete in all respect as approved and desired by the Engineer In-Charge at site.(b) PVC insulated & PVC sheathed aluminium conductor cable Overall Size 6mm² (1/1.40mm) Twin Core |
| 99 | Supply and erection of LED batten 20 watt LED (Including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimum 100 lumen per watt and operating voltage between 140 to 270 volt, THD < 10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per lS/IEC standareds) wattage of each low power LED less than 1watt input AC frequency50 HZ with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site. LED fitting as per specifications approved by Hon. Tech, Advisor to CM Punjab vide letter ION No. AT/2021/GL/1410-1422, Dated 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited laboratoru. |
| 100 | Supply and erection of Heavy Duty Exhaust Fan 300mm, 900RPM with aluminium louver shutter, double ball bearing longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the engineer-in-charge at site. |
