Tender For Construction Of Samaj Bhawan At Bed Prakash Sharma Land At Uttar Chenga Within P,Samiti 13, Under Mirik Panchayat Samiti,Mirik Darjeeling,
Tender Value
4.97 Lakhs
Estimated cost
Bid Submission
31 Jan 2024
0 days left
EMD
10000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
chenga → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Samaj Bhawan At Bed Prakash Sharma Land At Uttar Chenga Within P, Samiti 13, Under Mirik Panchayat Samiti, Mirik Darjeeling,
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. .(a) Depth of excavation not exceeding 1.500 mm. |
| 2 | Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics without rolling but including ramming. |
| 3 | Cost of stone boulder 150 mm size delivered ans stacked at site. |
| 4 | Ordinary cement concrete(mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes.(b) River bazree. |
| 5 | Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant codes.(ii) River bazree. |
| 6 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc.initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel.other than SAIL/TATA/RINL/JSW/JSPL/Shyam/SRMB/ISSL/BMASL/Electrosteel |
| 7 | Plum Concrete work with 40 % Cement Concrete with 30 mm down graded stone metal and 60% stone boulder of size 150 mm and above, placed in position as directed excluding shuttering if any.(i) (1:3:6) proportion. |
| 8 | Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). (a) 25 mm. to 30 mm. thick wooden shuttering as per decision & direction of the Engineer-in-charge. . |
| 9 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals).(i) Other Local Wood. |
| 10 | Z-batten shutters of door and window as per design having tongued and groove-half lap jointed as per direction of the Engineer-in - charge including fitting and fixing shutter in position, but excluding the cost of hinges and other fittings in ground floor. (A) Shutter with 25 mm. thick planks, 19 mm thick battens. (iv) Other Local Wood. |
| 11 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 12 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. (ii) With 1:4 cement mortar .(a) 20 mm.thick plaster. |
| 13 | Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 14 | (b) Priming one coat on timber or plasteredsurface with syntheticenamel oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 15 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sandparpering etc. in cluding using of approved putty etc. on the surface , if necessary.(a) On timber or plastered surface:(1) With super gloss (hi-gloss).(ii) Two coats( white in shade ). |
| 16 | Applying interior grade acrylic primer of approved quality and brand on plasteredor concrete surface old or new surface to received distemper /Acrylic emulsion paint including scraping and preparing the surface thoroughly , complete as per manufactured specification and as per directions of the EIC.In ground floor. (b) two coats. (i) water based interior grade Acrylic primer. |
| 17 | Applying exteriorgrade Acrylic primer of approved quality and brand on plaster or concrete surface old or new surface to receive decorative textured (mat finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly complete as per manufacturer\"s specification and as per direction of the EIC. In Ground Floor: (b) two coat. |
| 18 | supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately).(b) 40mm x 6mm, 200mm Length . |
| 19 | Iron butt hinges of approved qualityfitted and fixed with steel screws, with ISI mark.(vi) 100mm x 50 mm x 1.25 mm. |
| 20 | Iron butt hinges of approved qualityfitted and fixed with steel screws, with ISI mark.(iv) 75 mm x 47 mm x 1.70 mm. |
| 21 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:(iv) 150 mm long x 10 mm dia. bolt. |
| 22 | Anodise aluminium Aldrop/Slidingbolts of approvedquality manufactured form extruded section conforming to I.S. specifictation (I.S.2681/66) fitted and fixed complete. (i) 250 mm x 16 mm dia. bolt . |
| 23 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. (iii) 100 mm long x 10 mm dia. bolt. |
| 24 | Add @ 18 % GST on Rs. 405242.332 |
| 25 | Add @1 % Labour Cess on Rs. 478185.95 |
| 26 | Add @ 3 % Contingency of Rs. 478185.95 |
AI Tender Summary
Tender Timeline
Jan 18, 2024
11:30 IST
Tender Published
Tender notice published.
CompletedJan 31, 2024
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 05, 2024
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender