|
| 1 | Clearing and Grubbing road land including uprootingvegetation, grass, bushes, shrubs, saplings and trees girth up to 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, to all lead and lifts. Including removal and disposal of top organic soil not exceeding 150mm in thickness by mechanical means as per clause no. 201 of MoRD specification Rural roads-2004. |
| 2 | Milling on Bituminous Surface:Dismantling of existing damaged Bitumen surface by cold Milling Machine up to any depth and hauling the milled material up to any leadand stacking at nearest recycling Plant site (HSR 17.43.2)Note- The quantity of milled bituminous mix material shall be a recovery item as mention in BOQ item No. 32 (i). |
| 3 | Excavation for road work in soil by mechanical means including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including breaking of clods and disposal within ROWs as per technical clause 301 of MORT&H specifications.(HSR 17.74) |
| 4 | Earth work in excavation of foundation of structures as per drawing and technical specification,clause 305.1including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter,and disposal with all lead and lift , dressing of side and bottom andbackfilling in trenches with excavated suitable material as per clause no. 305 of MoRD specification Rural roads-2004. |
| 5 | Preparation of berms including filling of Earth work, excavation and cutting of earth in all kind of soils including dressing the bank, side slope to given levels and templates after breaking of clouds, including the cost of rolling and watering all allowances for labour hardness wetness irrespective of all lead and lift and including Compensation for earth taken from private land, fields etc. and compacted to meet requirement of table 300-2 of MoRT&H specification clause No. 30 and to entire satisfaction of the Engineer of the work confirming to PWD specification. As per X-section. This item also includes E/W if required in sub grade for Widening and Shoulder. Earth used for sub grade, shoulder and berms should have minimum CBR 8%. Note:- No earth work will be allowed to be taken from PWD B&R/ROW except for surplus earth after approval from Engineer. |
| 6 | Compaction of & preparation of sub grade including loosening, levelling of earth 225 mm thick top layer, rough dressing of soil, final dressing of earth to give level, camber, watering, rolling with road roller, compacting the bed to achieve minimum dry density as given in the Table 3000-2 as per technical clause 305 of MORT&H specifications (HSR 17.5.3) |
| 7 | Demolishing dry brick on end edging pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within anylead.(HSR 17.75) |
| 8 | Providing and laying Brick on end in soil/edging in required pattern with bricks of class designation (HSR 10.36) |
| 9 | Providing and laying 150mm thick granular sub base consisting of filter layer confirming to Table 400.1 Grading-I of MoRD specification, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared suface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRD specification-2004. Note: - 1.Only crushed stone metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer. |
| 10 | Providing & laying 75 mm thick (Compacted) stone metal (G-II) 63mm to 45mm gauge wearing coat to water bound macadam in layer of 75mm eachusing screening type ‘B’ compacting with three wheeled power rollers of 80-100 kN capacity or tandem or vibratory of 80-100 kN static weigth to achieve the desire density including lighting, guarding barricading and maintenance of diversion etc. as perclause no 405 of MoRD specification for Rural Roads-2004) as per drawing and design directed by the Engineer complete in all respects.(N.S.) Note: - 1.Only crushed stone metal material should be used. No local earth/ natural occurring sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer.approved by engineer. |
| 11 | Providing & laying 150/225 mm thick (Compacted) stone metal (G-III) 53mm to 22.4mm gauge wearing coat to water bound macadam in layer of 75mm eachusing screening type ‘B’ compacting with three wheeled power rollers of 80-100 kN capacity or tandem or vibratory of 80-100 kN static weigth to achieve the desire density including lighting, guarding barricading and maintenance of diversion etc. as perclause no 405 of MoRD specification for Rural Roads-2004) as per drawing and design directed by the Engineer complete in all respects.(N.S.) Note: - 1.Only crushed stone metal material should be used. No local earth/ natural occurring sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Materials to be used and operations of manufacturing shall be approved by engineer. |
| 12 | Providing and applying primer coat with bitumen emulsion (SS-I) on prepared surface of granular base including cleaning of road surface and spraying primer mix including silane at the rate of 0.60 kg/sqm using mechanical means asper Technical specification clause 502of MoRDspecification Rural roads -2004. Instruction issued from timeto time by MoRDregarding emulsion will be followd strictly |
| 13 | Providing and applyingTack coat of VG 10 ( 80/100 grade) bitumen using bitumen @ 0.25 kg per sqm. including clearing and blowing dust off the surface using a compressor and brooms conforming to clause 503 ofMoRD specification-200 .Instruction issued from timeto time by MoRDregarding VG-10 will be followed strictly |
| 14 | Providing laying and rolling of open graded pre mix carpet (PC) of 20mm thickness composed of 13.2 to 5.6 aggregates using bitumen VG-10 @1.36 kg per sqmand processed waste plastic @ 0.10 Kg/Sqm (Waste Plastic 7%) as per IRC SP -98 -2013 to required line , grade and level to serve as wearing course on previously prepared base , including mixing in a suitable plant, transported to site , laying with paver finisher and rolling with three wheeled 80-100 kn static roller capacity or with other approved equipment, finished to required level and grades as per MoRD specification clause 508.NOTE- Before carrying out bituminous work, coating & Stripping of bitumen aggregate mix is to be performed in accordance with IS-6241. If coating and stripping of bitumen aggregate mix is less than 95%, anti-stripping agent will be used by contractor. The anti-stripping agent should conform to the requirement as stipulated in IS 14982:2017. The cost so incurred will be considered as incidental to work and noting extra shall be payable. The type and brand of anti-stripping agent along with procedure shall be approved by SE-in-Charge in writing before start of work. A proper record of results be maintained and same shall be submitted along with bills by the contractor. |
| 15 | Providing and laying ‘B’ type seal coat with VG-10 grade bitumen @ 0.68 kg per sqm of road excluding cost of tack coat, with mixed material brought from Hot mix plant and laying with paver finisher and compacting with road roller to achieve specified/desirable value of compaction as per direction of Engineer including cost of lighting arrangement, sign board and night watch, complete in all respect as per clause 510 of MoRD specification for rural roads 2004. |
| 16 | Providing and Laying 80 mm thick ISI marked Interlocking Paver Blocks conforming to IS 15658:2006/IRC SP 63: 2004 of all shapes and colours in design mix cement M 40 over the bed of 30 mm thick fine sand complete in all respect. (HSR 17.69.2) |
| 17 | Providing and laying of cement concrete blocks of size 0.450 m x0.300 m x 0.15 m of cement concrete (C.C) M30 grade and spreading 25 mm thick sand underneath filling joints with sand on existing W.B.M./G.S.B base as per technical specification clause 1503 (HSR.17.66.1) |
| 18 | Providing & fixing Reinforced cement concrete M-25 grade precast 5th kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.1) |
| 19 | Providing & fixing Reinforced cement concrete M-25 grade precast ordinary kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.2) |
| 20 | Providing & fixing Reinforced cement concrete M-25 grade 200 meter stone of standard design as per IRC:8- 1980, fixing in position including painting and printing etc complete as per technical clause 804 of MORTH Specifications (HSR.34.27.4) |
| 21 | Reinforced cement concrete M 15 grade boundary pillars of standard design as per IRC:25-1967, fixed in position including finishing and lettering but excluding painting. Note: In case of soft ground, a proper foundation may be provided as per approved design. In case foundation is required to be provided, the items of excavation and foundation concrete are required to be measured and paid separately. |
| 22 | Providing and fixing of typical PMGSY informatory sign board with logo as per MoRD specification and drawing.Three MS plates of 1.6mm thick, top and middle plate duly welded with S flat iron 25mmX5mm size on back on edges,25mmX25mmX5mm. The angle iron frame of the lower most plate and flat iron frme of middle plate will be welded to 2 nos,.75mmX75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmX450mmX600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmX47mm of 12 SWG steel plate tube . All MS will be stove enamelded on both sides. Lettering and printing arrows, border etc. will painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.0. |
| 23 | Providing and fixing Logo Board of PMGSY size 600×600mm diamond shape with 1 plate of size 900×250 mm made of 60 gauge sheet over frame of angle iron 25×5×3 as per PMGSY specifications & drawing, painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 24 | Providing and fixing steel plate/ steel tube citizen informatory sign boards as prescribed by NRRDA (with two information plates of 750mm x 980mm size each) & other specifications conforming to the MoRD specification 2004; all inclusive, including excavation, concrete etc. Will supply warranty for sheeting Clause 801.3.11 |
| 25 | Providing and fixing of typical PMGSY Maintenance board with logo as per MoRD specification and drawing.Three MS plates of 1.6mm thick, top and middle plate duly welded with S flat iron 25mmX5mm size on back on edges,25mmX25mmX5mm. The angle iron frame of the lower most plate and flat iron frme of middle plate will be welded to 2 nos,.75mmX75mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mmX450mmX600mm below ground level. The top most diamond plate will be welded to middle plate by 47mmX47mm of 12 SWG steel plate tube . All MS will be stove enamelded on both sides. Lettering and printing arrows, border etc. will painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.0. |
| 26 | Providing & fixing overhead sign board 3050x1525mm cantilever type single sided using retro reflectiveSheetingTypeXI asperASTMD495609 and as per IRC67-2012 with retro reflectiveSheeting asper ASTM D 4956 – 09 and as per IRC 67 – 2012 fixed over 4mm thick Aluminium Composite Material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sidedandfixingthesamewithsuitablesizealuminium alloyrivets@200mmc/ctobacksupportframeof 40x40x6mm angle iron supported on designed single supportsystemofMSpipeandplatesintheformofa cantilevertypetrussmadewith350NBpipe@50kgper metre as vertical support, 50NB pipe @ 4.50kg per metre and 40NB pipe@ 3.61kg per metre for truss including base plates,gussetplates, designed RCC foundation for fixing in ground complete as per clause 802 of MORT&H specifications.Suppliershallprovideawarrantyasper clause 6.9 of IRC 67-2012 for retro reflective sheeting& a certifiedcopyoftestreportsfromanindependenttest laboratory including three year outdoor weathering test report for sheeting tested in India conditionconforming to clause 6.7 of IRC 67-2012. |
| 27 | Providing & fixing cautionary sign boardas per IRC 67- 2012 with using retro reflective Sheeting Class B as per ASTM D 4956 09 and as per IRC 67 2012 fixed over 3 mm to 4mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.75m for vertical post complete as per clause 801 of MORT&H specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting & a certified copy of test reports including three year outdoor weathering test report for sheeting tested in India condition from an independent test laboratory conforming to clause 6.7 of IRC67-2012 (i) 600 mmEQUILATERAL TRIANGLE (HSR.34.5.2) |
| 28 | 600 mm Circular (HSR.34.7.2) |
| 29 | 600 mm x 450 mm rectangular (HSR.34.9.2) |
| 30 | 900 mm HIGH OCTAGON |
| 31 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including Reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.Note:- Before start of work the contractor shall give brand , batch no. , manufacturing date of the material to be used and get approved thbe same from Engineer-In-Charge before use.(HSR 34.26) |
| 32 | Providing and laying in position ready mixed M-15 grade plain cement concrete @ 240 kg/cum with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge.(HSR.6.22.2.2) (Note: - Cement content considered in this item is @ 240 kg/cum. Less cement used as per design mix is recoverable. However no extra payment shall be made if excess cement is used as per design mix). |
| 33 | Brick work with common burnt clay non modular bricks of class designation 10.5 in foundation and plinth in cement Mortar 1:4. (HSR 7.21.1) |
| 34 | 12mm thick Plastering with cement mortar (1:3) on brick work in sub-structure as per Technical Specifications (HSR 11.5.2) |
| 35 | Providing and Laying 600 mm dia Reinforced cement concrete pipe NP3 prestressed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets 600 mm dia, as per clause 2900 of MORT&H specifications (HSR 17.61.1) Note:- Contractor shall supplybill of manufactureof pipes. Pipes should bear name of manufacturer and ISI mark along with bill duly valid ISI certificate of manufacturer should be supply. Without these bills certificate no payment shall be released. |
| 36 | Recovery Items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have beencalculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the pricequoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned (i) Bituminous Material @ Rs.1630 per cum. |
| 37 | Good bricks @ 5.00/- Per each |
| 38 | Bricks bats @ 450.00/- Per CumNote:- All quantities of the above materials have been worked out on the basis of theoritical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual sacrifying is found no lesser side , no claim of agency on this score will be entertained and full recovery on the basis of quoted rates and quantity exhibited in the entertained and full recovery on the basis of quoted rates and quantity exhibited in the BOQ shall be made . The reserve rates are minimum rates to be used as base for quoting purchase rates by the agency . No rates below the reserve price will be entertained and reserve price will be considered for all purpose in case the agency quotes lesser than reserve price.NOTE:- In case of any difference in the unit of nomenclature of any of the HSR/MORD Items depicted in this DNIT and that given HSR, the unit and nomenclature given in HSR /MORD shall be Applicable.OTE- It may kindly be noted that the contractorwould be obligated to carry out 05 years paid maintenance as per the rates fixed in the DNIT. However, the items of 05 yearsmaintenance shall not be part of BOQ to avoid any confusion. |
