|
| 1 | Section I Civil Work |
| 2 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. |
| 3 | Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction. |
| 4 | Construction of Embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. |
| 5 | Construction of sub grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads transporting to site,spreading,grading to required slope and compacted to meet requirement of table No;300-2 |
| 6 | Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.Grading-1 Material |
| 7 | Construction of wet mix macadum by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. |
| 8 | Providing and laying dense graded bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5 per centby weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects.GRADING-1 MATERIAL |
| 9 | Providing and applying primer coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.60 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. |
| 10 | Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. |
| 11 | Providing and laying bituminousconcrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.2 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 507 complete in all respects with VG-30 Bulk Bitumen. |
| 12 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. |
| 13 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing |
| 14 | Road Markers/Road Stud with plastic body of RPM/ASA/HIPS as per clause 804.2.1 of MORTH, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 15 | Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 16 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mmthick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 17 | Earth |
| 18 | Section- IICable Trench (566.12 mtr) |
| 19 | Earthwork in excavation in foundation trenches in ordinary soil(vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 m includingall lifts, levelling , ramming the foundation trenches, removing roots of trees, serbs all complete as per approved design,building specification & direction of E/I. |
| 20 | Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and 1.5M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume) |
| 21 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 22 | Providing designation 75A brick work inC.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 23 | Providing and laying in position reinforced cement concrete of specified grade excluding the cost of centering and shuttering- All work upto plinth level: 1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mmnominal size). |
| 24 | Centering and Shuttering including struting, propping etc. and removal of form forFoundation, footing,bases of column, etc. for mass concrete. |
| 25 | Providing TMT reinforcement of following dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I. |
| 26 | 8 mm dia (40 %of total reinforcement) |
| 27 | 10mm dia(60%of total reinforcement) |
| 28 | Providing 12mm thick cement plaster (1:6)with clean coarse sand of F.M. 1.5 and including cost of screening, curingwith all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I |
| 29 | Providing 1.5 mm. cement punning including curing carrage of water withall leads and lifts as per buildingspecification and d |
| 30 | Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. |
| 31 | 250 mm dia. R.C.C. pipe |
| 32 | Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flats as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, hoisting carriage of grill to work site, hoisting as per building specification and direction of E/I. |
| 33 | Cairage Of Meterial |
| 34 | (A) Coarse sand |
| 35 | (B) Stone Chips |
| 36 | (C) Bricks |
| 37 | (D) Cement |
| 38 | (E)Steel |
| 39 | PERIPHERAL ROAD 2000.00 Mtr length |
| 40 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. |
| 41 | Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal upto 1000 metres. (Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m)Including Royalty etc.@ Rs. 27.48 per cum, cost of watering, rolling & compaction. |
| 42 | Loosening, leveling and Compacting original ground supporting embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction. |
| 43 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 Rolling with Vibratory Roller( Lead 3 Km) |
| 44 | Granular sub base with coarse graded materials (Table:-400-2)(Construction of granular sub base by providing coarse graded material spreading in uniform layers with motro grader on prepared surface mixing by mixing by mix in plae method with rotavator at OMC and ompacting with vibratory roller to achieve the desire density completed as per claue 401)for grading II materials |
| 45 | ProvidingP.C.C.M200 in normal mix of(1:1.5:3) in foundation with approved quality of stonechips 20mm to 6 mm size graded and clean coarse sand to F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 46 | Embankment construction with material obtained from Borrow Pits (Construction of embanlment with approved material obtained from borrow pits with all lifts and leads transporting to site, spreding , grading to required slope and compacting to meet requirement of table 300-2) |
| 47 | ROAD MARKING- |
| 48 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. |
| 49 | Road Markers/Road Stud with plastic body of RPM/ASA/HIPS as per clause 804.2.1 of MORTH, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling hole 30 mm upto a depth of 60 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS 873 part 4:1973) |
| 50 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 51 | Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 52 | Carriage of materials by truck or by any mechenical means loading,unloading & stacking etc. all complete job as per direction of E/I. |
| 53 | Bricks |
| 54 | Coarse Sand |
| 55 | Chips |
| 56 | Cement |
| 57 | Electical installation works |
| 58 | Note:- OF MAKE (1)PVC insuleted copper conductor wire of make:-Havell\"s/Polycab/Anchor (2)PVC conduit of thiknss 1.5mm/2mm for wiring:-Polycab/ANCHOR/AKG(3) GI modular box of make -: Anchor/ Havells/Legrand/ (4)Switches/soket outlet for modular type:- Anchor (roma)/Havells(cabtree)Legrand (5)MCCB,MCB,SFU,CHANGEOVER,RCCB,MCB-DB:-Havell\"s/L&T/C&S(6)XLPE/PVC aramoured cable:-Havell\"s/Polycab/V-guard(7) LED ITTING FIXTURE -: Havells/Bajaj/Crompton (Model/as per E/I )(8) CEALING / WALL / EXHAUST FAN -: Havells / Bajaj / Usha / Crompton (Model/as per E/I )(9) OCTAGONAL POLE-: Bajaj/Philips/Surya (10) CHEMICAL EARTHING OF MAKE - TRUEPOWER EARTHING (11) CENTRALISED AIR CONDITIONING OF MAKE - VOLTAS/MITSHUBISHI/ TOSHIBA/DAIKIN(12)ALL ELECTRICAL WIRING WORK SHOULD BE CONCEALED |
| 59 | S/F \"B\" series. S.P.MCB:-Supplying and fixing 6 amps to 32 amps rating,240 volts, \"B\" series miniature circuit breaker suitable for lighting and others loads of following poles in the exiting MCB DB complite with connections. Testing and commisioning etc as required. |
| 60 | 6/32 amps,single pole, \"B\" SERIES |
| 61 | P/F M.V. danger notice plate:-Providing and fixing M.V danger notice plate of 200mm x150mm made of mild steel, at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red coiour on front side as required. |
| 62 | G.I Earth pipe electrode with salt charcoal :-Earthing with G.I. earth pipe 4.5 mtr long,40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required. with salt charcoal or coke. |
| 63 | Copper Earth plate electrode:-Earthing with copper earth plate 600mmX600mmX3mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required.( with salt charcoal or coke) |
| 64 | S/L 8 SWG copper wire ground :-Supplying and laying 8 SWG copper wire 0.50 metre bellow ground level for conductor earth electrode, including soldring etc. as required. |
| 65 | S/L 6 SWG G.I. wire ground :-Supplying and laying 6 SWG G.I. wire 0.50 metre bellow ground level for conductor earth electrode, including soldring etc. as required. |
| 66 | S/L 25mmX5mm.Copper earth strip in ground :-Supplying and laying 25mmX5mm copper strip in 40 mm dia GI pipe from earth electrode including connection with brass nut, bolt,spring washar excavetion and re-filling etc as required. |
| 67 | Laying of one number PVC insuleted and PVC sheathed/ XLPE power cable of 11 KV grade of size not exceeding 35 sq.mm. direct in ground including excavetion, sand coushioning, protective covering and refilling the trench etc as required. |
| 68 | Laying of one number PVC insuleted and PVC sheathed/ XLPE power cable of 11 KV grade of size exceeding 35 sq.mm.but not exceeding95sq.mm. direct in ground including excavetion, sand coushioning, protective covering and refilling the trench etc as required. |
| 69 | Laying of one number PVC insuleted and PVC sheathed/ XLPE power cable of 11 KV grade of size exceeding 95 sq.mm. but not exceeding 185 sq.mm. direct in ground including excavetion, sand coushioning, protective covering and refilling the trench etc as required. |
| 70 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. |
| 71 | Above 185 sq. mm and upto 400 sq. mm |
| 72 | Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required. |
| 73 | Supply ofPVC XLPE insuletd PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts,(conforms to IS:7098, part-1)g |
| 74 | 10 sq.mm. 4 core FOR BOLLARD |
| 75 | 16 sq.mm. 4 core FOR SINGLE ARM STREET LIGHT |
| 76 | 25 sq.mm. 3.5 core FOR PERIFERIAL FLOOD LIGHT |
| 77 | 35 sq.mm. 3.5 core FOR HIGH MAST |
| 78 | 50 sq.mm. 3.5 core FOR STREET LIGHT SAUB PANEL |
| 79 | 70 sq.mm. 3.5 core FOR 16 LS QTR |
| 80 | 120 sq.mm. 3.5 core FOR PROPOSED HIGH MAST PANEL |
| 81 | 150 sq.mm. 3.5 core FOR EXISTING FEEDER |
| 82 | 300 sq.mm. 3.5 core FOR EXISTING MAIN PANEL PROPOSED PANEL |
| 83 | Supplying and fixing of light class G.I. pipe of 80 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required |
| 84 | Supplying and fixing of light class G.I. pipe of 100 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required |
| 85 | Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. |
| 86 | 40 mm dia |
| 87 | Supplying and making end termination with brass commpression gland and aluminium lugs for following size of PVC insuleted and PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 88 | 4 X 10 sq. mm (25mm) |
| 89 | 4 X 16 sq. mm (28mm) |
| 90 | 3½ X 25 sq. mm (28mm) |
| 91 | 3½ X 35 sq. mm (32mm) |
| 92 | 3½ X 50 sq. mm (35mm) |
| 93 | 3½ X 70 sq. mm (38mm) |
| 94 | 3½ X 120 sq. mm (45mm) |
| 95 | 3½ X 150 sq. mm (50mm) |
| 96 | 3½ X 300 sq. mm (70mm) |
| 97 | Supplying and making straight through joint with cast resin compound including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required |
| 98 | 3½ X 150 sq. mm |
| 99 | 3½ X 300 sq. mm |
| 100 | Supplying and fixing of cable junction box with RYBG Terminal plate and Din bar of make sintex /Hensel |
| 101 | SITC of following rating LED street lighting luminarie with pressure dia cast housingh and toughned glass cover ,IP 66 Protection , LUMINOUSEFFICARY >_110 LM/W with lens in existing pole /pipe for supply voltage 100-270V AC ,50 Hz, luminarie shall be confirm to IS 10322 part -5 /section -3 and shall be complete with all neccssary accessosries as required. |
| 102 | 90 /100 W LED Street light of make bajaj/havells/crompton/C&S /Jaquar |
| 103 | S.I.T.C of following rating LED FLOOD lighting with pressure dia cast housing and toughened glass cover (IP 66 protection)in existing pole/pipe /platform/periferial wallfor supply voltage 100-270v AC,50Hz Luminire shall be confirmto IS-10322 part-5/ section-3 and shall be complete with all neccssary accessories as required.of make bajaj/havells/crompton/C&S |
| 104 | 50/60 W LED FLOOD LIGHT of make bajaj/havells/crompton/C&S /Jaquar |
| 105 | 150/160 W LED FLOOD LIGHT of make bajaj/havells/crompton/C&S /Jaquar |
| 106 | 240 W LED FLOOD LIGHT of make bajaj/havells/crompton/C&S /Jaquar |
| 107 | S.ITC ofFollowing rating approved make LED Bollard fitting with Cylindrical shape of hight 600 to 850mm Power input - 8/9 watt with dia cast aluminium housing opel with PC diffuser IP:65/54 protection , conferming to IS:10322 part -5 etc all complete as required (excluding plinth charge) Of make bajaj/philips/polycab/jaquar |
| 108 | Constructing platform of 400 mm dia 600 mm long with 300 mm depth bellow ground and rest 300 mm exposed over ground to supportBollardlight with all finishing plaster putty & paint and minimum 75mm PCC on TOP all complite asper direction of E/I |
| 109 | Supply /fitting/fixing of 50 mm dia chemical Earthing Electrode 3 mtr length ,Backfill compound chemical 4 bag (per bag 25 kg), Earth cutting removing and installation charge as. required. OF MAKE POWERGRIP EARTHING ELECTRODE. RANCHI/ELECTROGRIP RANCHI |
| 110 | Supply of 7 Mtr height Octagonal Hot Dip Galvenized pole (BOP - 7030) with top dia 70 mm, bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x12mm (L X B X T) including suitable sizes of foundetion bolt all complete as requried. (Without Arm) |
| 111 | Supply of 9 Mtr height Octagonal Hot Dip Galvenized pole (BOP - 9031) with top dia 70 mm, bottom dia 130 mm & made of 3 mm thick sheet base plate dimensions 200x200x16mm (L X B X T) including suitable sizes of foundetion bolt all complete as requried. (Without Arm) |
| 112 | 1.5 Mtr Single Arm suitable for 70 mm TOP |
| 113 | Instalation Testing & Commisioning of 7 Mtr Octagonal Pole & light fitting with the help of tools & plants, wiring of luminaires with all materials and construction of shallow foundetion with M 25 grade concreat considering safe soil bearing capacity of 10T/Mtrs sq |
| 114 | Instalation Testing & Commisioning of 9 Mtr Octagonal Pole & light fitting with the help of tools & plants, wiring of luminaires with all materials and construction of shallow foundetion with M 25 grade concreat considering safe soil bearing capacity of 10T/Mtrs sq |
| 115 | Supply of 12 Mtr. High Mast in one section Construction S355 grade as per BS-EN 10 025 Top Dia 100 mm , botttom dia 360 mm , plate thickness 3 mm, 12 side polygon, galvenisation as per BS-EN ISO 1461, base plate dia 520 mm,base plate thickness 25 mm, GI single spike lightning protection, maximium wind speed 47 m/s as per IS:875 (part III)with 6 Nos foundetion bolts of PCD 445 mm TS 600/24 mm dia /850 mm long. Luminaires carrage : Material for 40 NB ERW Class B,MS Pipe, dia of carriage ring 535 mm (ID)with 6 Arms welded, 2 section having carrying capacity upto 8 luminaires,Trailing cable : 5 core 2.5 sq mm,PVC flexible copper conductor Winch/ power tool : Double drum, SWL 350 KG with 0.75 HP 6 Pole single speed integral motor Rope : Grade AISI 304, 7/19 construction, dia 5 mm, BLC 1450 X 2 having 2 nos of continues rope. Aviation obstruction light : twin dome aviation obstruction light LED type as required. |
| 116 | For 16 Mtr High Mast : ITC of the high mast and light fixture with the help of suitable tools and plants. Wiring of luminaries with all wiring material like PVC insuleted PVC PVC sheathed flexible cable of suitable copper conductor, lugs,MCB and all labour & construction of shallow foundetion with M 25 grade concrete for the high mast considering safe soil bearing capacity of 10 T / Mtrs sq etc as required for 16 Mtr High Mast . |
| 117 | FOR HIGH MAST PANELS/F of Outdoor stand mounted Double door Feeder panel with 63 Amp TPN, MCB incommer,63 amp TPN contactor autometic switching of luminaire, power tool control incomer outgoing terminal , single dial timer, outgoing ,incoming terminals and control circuit for power tool control with 2 nos 9A contactors and rise lower push button, incoming 35 sq mm and outgoing 16 & 2.5 sq mm terminals. IS : 1944 - 5 |
| 118 | FOR STREET LIGHT SUB PANELS/F of Outdoor stand mounted Double door Feeder panel with 63 Amp TPN, MCB incommer,63 amp TPN contactor autometic switching of luminaire, power tool control incomer outgoing terminal , single dial timer, outgoing ,incoming terminals , incoming 50 sq mm and outgoing 16 & 2.5 sq mm terminals. IS : 1944 - 5 |
| 119 | FORSTREET LIGHT AND AUDITORIUM MAIN PANELDesign manufacture, supply installation, testing and commissioning of WEATHER PROOF DOUBLE DOOR with rubber gasket 14 SWG sheet steel fabricated cubical type floor mounting front operated construction, enclosure class - IP 52, finishing with 7 tank process and powder coating of the entire panel including covers in required shade complete with top / bottom ( as called for ) removable gland plates, cable alleys, double compression doors to achieve dust and vermin proof complete with all inter connections small wiring by copper wires, ckt labels etc. The Copper Bus Bar shall be of suitable size for 500 volts, 3 phase 50 Hz TPN, electrolytic copper as per Is 8623 insulated by heat shrinkable sleaves with surround joints. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmeter, selector switches, CT\"s, PT\"s, etc. The panels shall be got fabricated only from panel builders having 7 tank process finishing system and CPRI approved certificate for similar LT Panel. |
| 120 | PANEL(NORMAL SUPPLY) :35 KA) -INCOMING (1- sets) each with following: |
| 121 | (A) INCOMING |
| 122 | 4 Pole MCCB with Adjustable Thermal Seting 800Amp 35 KA |
| 123 | 800A, 415V,Heavy duty three phase with neutral Busbar Chamber |
| 124 | (B) OUTGOING |
| 125 | 4 Pole MCCB with Adjustable Thermal Seting 630Amp 35 KA |
| 126 | 4 Pole MCCB with Adjustable Thermal Seting 25/100 Amp 35 KA |
| 127 | 4 Pole MCCB with Adjustable Thermal Seting 150/160 Amp 16 KA |
| 128 | (C) OTHER ACCESSOSRIES |
| 129 | DIGITAL VOLT METER (0-500V) 3phase class 0.5 |
| 130 | DIGITAL A METER (0-500Amp) 3phase class 0.5 |
| 131 | COPPER WIRE 1.5MM |
| 132 | COPPER WIRE 10MM |
| 133 | COPPER WIRE 16MM |
| 134 | COPPER WIRE 25MM |
| 135 | LED INDICATOR LAMP R/Y/B/G |
| 136 | C.T COIL OF CT ratio 500/5 IS2705 part -3 |
| 137 | S/F WEATHERPROOF CANOPY TYPE double door with rubber gasket Floor mounted cubical panel board , fabricated with 14 gauge iron sheet with Iron angle frame padestal etc suitable for panel mounted switch disconnector, Space for busbar,insulator,switchgears and painting etc.as required .AS PER E/I (but without busbar copper strip /Switchgears/MCB\"s/MCCBsWire and other accessosries) The rate of this itom is sum of A+B+C =Rs.174094.09@ 50% That is Rs.87047.04 |
| 138 | FOR HIGH MAST FEEDERDesign manufacture, supply installation, testing and commissioning of WEATHER PROOF DOUBLE DOOR with rubber gasket 14 SWG sheet steel fabricated cubical type floor mounting front operated construction, enclosure class - IP 52, finishing with 7 tank process and powder coating of the entire panel including covers in required shade complete with top / bottom ( as called for ) removable gland plates, cable alleys, double compression doors to achieve dust and vermin proof complete with all inter connections small wiring by copper wires, ckt labels etc. The Copper Bus Bar shall be of suitable size for 500 volts, 3 phase 50 Hz TPN, electrolytic copper as per Is 8623 insulated by heat shrinkable sleaves with surround joints. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmeter, selector switches, CT\"s, PT\"s, etc. The panels shall be got fabricated only from panel builders having 7 tank process finishing system and CPRI approved certificate for similar LT Panel. |
| 139 | PANEL(NORMAL SUPPLY) :35 KA) -INCOMING (1- sets) each with following: |
| 140 | (A) INCOMING |
| 141 | 4 Pole MCCB with Adjustable Thermal Seting 250Amp 35 KA |
| 142 | 300A, 415V,Heavy duty three phase with neutral Busbar Chamber |
| 143 | 160A 4 pole on - load change over switch open excution type cubical |
| 144 | (B) OUTGOING |
| 145 | 4 Pole MCCB with Adjustable Thermal Seting 25/100 Amp 16 KA |
| 146 | 40 amps ,DP |
| 147 | 50/63 amps, TPN |
| 148 | 40 amps 2 Pole Isoletor |
| 149 | 40 amps 4 Pole Isoletor |
| 150 | (C) OTHER ACCESSOSRIES |
| 151 | DIGITAL VOLT METER (0-500V) 3phase class 0.5 |
| 152 | DIGITAL A METER (0-500Amp) 3phase class 0.5 |
| 153 | COPPER WIRE 1.5MM |
| 154 | COPPER WIRE 10MM |
| 155 | COPPER WIRE 16MM |
| 156 | LED INDICATOR LAMP R/Y/B/G |
| 157 | C.T COIL OF CT ratio 500/5 IS2705 part -3 |
| 158 | S/F WEATHERPROOF CANOPY TYPE double door with rubber gasket Floor mounted cubical panel board , fabricated with 14 gauge iron sheet with Iron angle frame padestal etc suitable for panel mounted switch disconnector, Space for busbar,insulator,switchgears and painting etc.as required .AS PER E/I (but without busbar copper strip /Switchgears/MCB\"s/MCCBsWire and other accessosries) The rate of this itom is sum of A+B+C =Rs.80480.21@ 50% That is Rs. 40240.10 |
| 159 | Construction of Platform for fidder pillar of fix- 1500 mm x 2100 mm with excavation depth of 500 mm and 395 mm protected above OGL. Brickwork of 375 mm below OGL & 250 mm of 300 mm hieght above OGL. Top of platform to be finished with 75 mm PCC with all arround plaster and neat cement punning. All work to be completed as per drawing design and direction of EI. |
| 160 | ABC type Fire Extinguisher |
| 161 | Stored Pressure ABC Type multi-purpose Fire Extinguisher, Fitted with Squeeze Grip Type Valve with Pressure Indication Gauge & Pressure Discharge Hose Complete with All Mounting Brackets Etc.Conforming to IS:15683 (Cap : 6 Kg) |
| 162 | CO2type Fire Extinguisher |
| 163 | (A)HSN CODE -: 8543.20.20Supply and testing of SURGE GENERATOR, MODEL: T-1005(7)Suitable for fault location in low voltage power cables DC High Voltage Testing up to 5 KV Output current more than 200 mA.Surge Testing Range 0-5 kV 750 Joules Energy on 5 Kv(B)HSN CODE -: 8543.70.29Supply and testing of Sensitive acoustic and magnetic sensor to pinpoint fault.Proportional signal on large L.C.D Coincidence figure readout i.e. distance to the fault in milliseconds on LCD.Accurate display of magnetic and acoustic indicationsLight weight receiver.(C)HSN CODE-: 9030.20.00Supply and testing of Reflectometer, Model: T-610Reflectometer for pre-location of cable faults Digital Time Domain Reflectometer.Pulse Echo, Impulse Current & Decay methods. Large and automatic graph storage. 10” touch screen for easy operation.Testing Range up to 160 KM. |
| 164 | (A)HSN CODE -: 8543.20.20 ( 01 Nos)(B)HSN CODE -: 8543.70.29 ( 01 Nos)(C)HSN CODE-: 9030.20.00 ( 01 Nos)Total 3 Itemsof make TECHNO INSTRUMANT INDIA PVT. LTD / GLOBAL TRADING /LOMAS |
| 165 | Add 18% GST |
| 166 | Add 1% Lebour Cess |
