|
| 1 | Dismantling of cast iron or reinforced concrete drain pipes 100mm dia, jointed in cement mortar and taking out of trenches, all as specified and directed. |
| 2 | Dismantling of cast iron or reinforced concrete drain pipes 75mm dia, jointed in cement mortar and taking out of trenches,all as specified and directed. |
| 3 | Dismantling water tanks exc 250 and n exc 500 Ltrs capacity of any type or size complete all as specified and directed. |
| 4 | Dismantling water tanks exc 500 and n exc 1000 Ltrs capacity of any type or size complete all as specified and directed. |
| 5 | Dismantling floor hearth wall tiling including cement mortar bedding (but not backing) includingrubbish off the premises complete all as specified and as directed. |
| 6 | Dismantling of Asbestos cement (corrugated, semicorrugated and Transulent sheet etc) sheets in roof covering incl ridges complete all as specified and directed. |
| 7 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 8 | Demolition of cement concrete (un-reinforced ) Roofs, floors (other than groundfloors), beams, staircases, landing,chajjas and similar suspended work complete all as specified and directed.. |
| 9 | Demolition of RCC of any description and in any position not otherwise specifically provided for complete all as specified and as directed . |
| 10 | Demolition of cement concrete (un-reinforced ) in ground floors and pavings not exceeding 15cm thick(below or above ground level ) . |
| 11 | Demolition of Bricks or stone masonry built in cement mortar complete all as specified. |
| 12 | Demolition of cement concrete (un-reinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed.. |
| 13 | M&L for cutting existing slab for repairing pvc pipe and make the same after fixing the pipe without any leakage and seepage all as specified and directed. |
| 14 | Supply and fix in PVC(SWR) pipe 110 mm dia single socketed in any length with rubber ring joint , laid in trenches or in floor all complete as specified . |
| 15 | Supply and fix PVC(SWR) pipe 75 mm dia single socketed in any length with rubber ring joint , laid in trenches or in floor all complete as specified . |
| 16 | Supply and fix 110 mm bore PVC (SWR) bend , any radius complete all as specified . |
| 17 | Supply and fix 75 mm bore PVC (SWR) bend , any radius complete all as specified . |
| 18 | Supply and fix 75 mm bore PVC (SWR) Vent Cowl complete all as specified . |
| 19 | M&LPVC (SWR) gully trap125/110 mm, setting and jointing wilh solvent cement complete all as specified and directed. |
| 20 | S & F steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls,(concealed) 15mm bore.including taking down old pipe complete all as specified and as directed. |
| 21 | S & F steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20mm bore.including taking down old pipe complete all as specified and as directed. |
| 22 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 750 Llitres including PTMT ball valve high pressure of 20mm completeall as specified and directed. |
| 23 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 Llitres including PTMT ball valve high pressure of 20mm completeall as specified and directed. |
| 24 | S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 Llitres including PTMT ball valve high pressure of 20mm completeall as specified and directed. |
| 25 | S&F in repairs Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore and completeall as specified and directed. |
| 26 | S&F PTMT ball valves 20 mm dia high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes and fixed to iron pipes.complete all as specified and as directed. |
| 27 | Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing andfixing new ones complete all as specified and as directed. |
| 28 | S&F 3mm thick sheet glass ordinary quality fixing with putty in square not exceeding 0.5 Sqm in each pane. complete all as specified and as directed. |
| 29 | S&F 3mm thickfigured glass, pin head type. complete all as specified and as directed. |
| 30 | Taking down cement plaster from brick or stone walls, ceiling etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified anddirected. |
| 31 | M&L for 15 mm thick rendering on fair faces of brick work or cement concrete surfaces in cement mortar 1:4, finished fair and even without using extra cementincl mixing of water proofing compound complete all as specified. (Note: Water Proofing compound shall be measured and paid for separately) |
| 32 | M&L for rendering 5 mm thick in CM 1:3 on ceiling,chajja,roof projection etc finished even and smoothwithout using extra cement.complete all as specified and as directed. |
| 33 | M & L Rendering 15mm thick in CM 1:6 on brick or concrete surfaces including finihsed the surface smooth and even without using extra cement complete all as specified and as directed. |
| 34 | M&L for applying two coats of cement base painton new plastered surfaces of wallincluding preparation of surfaces over a coat of priming paint complete all as specified & directed |
| 35 | M&L for applying one coat of cement based paint for external surfaces including preparation of surfaces including filiing all cracks with approved crack filler complete all as specified and directed. |
| 36 | Use and waste of formwork to sides & sofits of chajja etc for rough finished concrete surfaces complete all as specified and directed. |
| 37 | Material and labour for providing RCC (1:2:4 ) type B1 (using 20 mm graded stone aggregate)as in chajja complete all as specified anddirected. |
| 38 | Material andlabour for mild steel TMT bars 6 to 8mm bar, cut to length, bent to shape required, including cranking, bending,fixed with welding complete all as specified and directed . |
| 39 | M&L for welding in repairs n. exc 2.5 cm in length of metal thickness exc 6 mm and n. exc 9 mm upto 6 mtr from avg ground level complete all as specified and directed . |
| 40 | Material and labour for crack filling with approved crack filler to arrest seepage and running water through masonry / RCC surfaces etc. complete all as specified by Engineer-in-Charge.Make : Dr. Fixit Leak Plug or its equivalent |
| 41 | Material and labour for preparation of plastered surfaces and applying two coats of water proof coating (Dr. Fixit Rain Coat exterior waterproof coating)over a coat of primer (Dr. Fixit Prime seal diluted with potable water by volume in 2:1 ratio, 2parts primer and 01 part water) including filling of cracks upto 5 mm width, with Dr. Fixit Crack-X, or Dr. Fixit unifiller on external surfaces of wall to arrest the seepage/dampness and runnging water in the masonry surfaces complete all as specified and directed.Make : Dr Fixit or its equivalent. |
| 42 | M&L forplain cement concrete 1:5:10 type E-2 (using 40 mm graded aggregates) as in floor filling complete all as specified and as directed. |
| 43 | Rendering 15mm thick in CM 1:3 using water proofing compound as per manufacture instruction, finished even and smooth with out using extra cement as in sunken floor complete all as specified and as directed. (Note: WPC will be measured and paid separately) |
| 44 | M&L for priming on plastered surfaces with bituminous primer and applying heavy treatment for severe conditions using glass fibre base bitumen felt, grade 2in 100 mm overlaps both longitudinally and transverselyby torchbondingas in sunken floor ( bottom and vertical surfaces ) complete all asspecified and directed |
| 45 | Supply only water proofing compound complete all as specified and as directed. |
| 46 | M&L for Glazed ceramic coloured tiles of size 450x300x6 to 7 mm thick wall tiles set and jointed in neat cement slurry and pointed in white/coloured cement to match with the colour of tile over 10 mm thickplaster in CM 1:4as in skirting / dados etc,complete all as specified and directed. |
| 47 | M&L for Non - skid Ceramic jointfree tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 48 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 49 | S&F in repairsVitreous china wash hand basin white flat back size 550x400mm including brackets, CP pillar cock (fancy type )of 15mm bore, CP waste fittings 32mm, incl waste pipe complete all as specified and directed. |
| 50 | S&F in repairsVitreous china orrisa pan squatting pattern 580 X 440mm with integral foot rests including P or S trap, PVC low level flushing cistern 10 ltrs capacity complete all as specified and directed. |
| 51 | S&F in repairs PVC low level flushing cistern 10 ltrs capacity white , with inlet ball valve , float and handle including brackets , Flush pipe of polythylene of low or high density or PVC 32 mm dia , PVC connection 15mmsize with PTMT nuts of length 450mm complete all as specified and directed. |
| 52 | M&L for 75mm thick plain cement concrete in (1:3:6) type C2 (using 40 mm graded aggregate) as in plinth protection finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed. |
| 53 | M&L for Hardcore broken stone boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true su |
| 54 | M&L for75 mm thick PCC 1:3:6 type C-2 using 40mm graded aggregate as in sub base of floor etc complete all as specified and as directed. |
| 55 | M&L for sand cushionlaying and fixing for interlocking tiles. |
| 56 | M&L machine pressed precast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 80 mm thickness M-40 grade with grey cement and no pigment. complete all as specified and directed. |
| 57 | M&L for chequered cement concrete tile 300 mm x 300 mm x 25 mm thick setjointed andpointed in neat cement slurry in floor with grey cement and pigment and including 20 mm thick screed bed cement mortar 1:4 all as specified and directed. |
| 58 | M&L for cement concrete 1:2:4 type B1 (20 mm graded stone aggregate) as in coping, kerbs and similar work etc including necessay form work complete all as specified. |
| 59 | M & L for brick work with sub class \"B\" bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as incomplete all as specified and as directed. |
| 60 | Material and labour for brick work withbricks class designation 75, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed. |
| 61 | M & L for brick work with sub class \"B\" bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:3)complete all as specified and as directed. |
| 62 | Supply and fix in repair 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement completeall as specified and as directed. |
| 63 | Supply and fix in repair 75 mm dia PVC (SWR) floor Nahani trap, plain with grating including jointing with solvent cement completeall as specified and as directed. |
| 64 | Taking down rolling shutters size n exc 8 Sqm, replacing worn out/unserviceable parts with new ones, overhauling applying grease refixing in position and making functional complete all as directed. |
| 65 | M & L for Overhauling of rolling shutter sizes n exc 8 Sqm, (without taking down from position but by opening hood cover), applying grease for trouble free operation refixing the hood cover in position and making functional complete all as directed. |
| 66 | Taking down existing water proofing treatment with tarfelt including cement plasterfrom roof including parapets etc, and removing the debris to a distance not exceeding 250m complete all as specified and directed. |
| 67 | M&L for 40mm thick plain cement concrete (1:2:4) type B1 (using 20 mm graded stone aggregate) as in padding (level course) on roof complete all as specified and as directed. |
| 68 | M&L for 40 mm thickfor PCC (1:2:4) type B1, (20 mm graded stoneaggregate) as in flooring finished even and smooth using extra cement. |
| 69 | M&L for rendering 10 mm thick in CM (1:3) using water proofing compoundas per manufacturer instruction as in roof and chajjascomplete all as specified and as directed. Note : Water proofing compound will be measuredand paid separately. |
| 70 | M&L for priming plastered roof surfaces (Non approachable roof ) with bituminous primer @ 0.3 Kg/Sqm as per IS 3384 and providing water proofing treatment by applying 3.5 Kg/Sqm ATACTIC polypropylene (Advanced APP torch on membrane) having polyster film reinforcement stabilized with fibre glass and two coat aluminium paint over APP membrane of thickness 3mm by torch bonding complete all as specified and as directed. |
| 71 | M&L for water proofing treatment with APP based standard membrane over PCC padding in approachable roof with the following courses of treatment : (a)Apply bituminous primer (IS3384) @ 0.30 Kg/Sqm of the surface area including cleaning the surface complete all as specified .(b)Apply APP plastomeric bitumen based water proofing membrane polyster reinforced (3.50 Kg/Sqm) with 10 cm overlaps and torch bonded at joints including surface preparation before and after application of treatment as per manufacturers instruction complete all as specified. |
| 72 | M&L for M&L for cement concrete tiles 25cm x 25cmx22mm thick machine pressed set jointed and pointed in neat cement slurry in floors and cut polished with grey cement and no pigment over 20 mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 73 | Supply only Polyster Fibre . Make (RECRON 3S or equivalent) complete all as specified and as directed. |
| 74 | M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. |
| 75 | M&L for plain cement concrete type B1, (20 mm graded aggregate) as in roof kerbs, tank stagging and similar works etc complete all as specified and directed. |
| 76 | M&L for complete removal of existing treatment including preparing surfaces of wall and applying two coats of weather proof exterior emulsion paint (APEX ULTIMA of Asian Paints or equivalent of Berger/Nerolac) over exterior weather proof 3mm thick putty over a coat of primer including filiing all cracks with approved crack filler complete all as specified and directed. (Note : Two coats exterior emulsion paint will be done by mechanically spraying gun) |
| 77 | M&L for complete removal of existing treatment including preparing surfaces of ceiling and applying two coats of weather proof exterior emulsion paint (APEX ULTIMA of Asian Paints or equivalent of Berger/Nerolac) over exterior weather proof 3mm thick putty over a coat of primer including filiing all cracks with approved crack filler complete all as specified and directed. (Note : Two coats exterior emulsion paint will be done by mechanically spraying gun) |
| 78 | M&L for preparation of new plastered surfaces and applying two coats of exterior emultion weather proof paint(APEX Ultima) over a coat of primer over 3mm wall care putty complete all as specified. Make :Apex Ultima of Asian Paint or any other equavalent .Note : Mentioned paint should be applied by roller brush only. |
| 79 | M&L for Preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer including applying 3mm thick wall care putty complete all as specified and directed. |
| 80 | M&L for preparation of new plastered or un- plastered surfaces of ceiling and applying three coats of white washcomplete all as specified and directed. |
| 81 | M&L Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of anycolour having tensile strength of 550 Mpa as in roof covering/ cladding towall, fixed with self tapping screws complete all as specified and directed. |
| 82 | S&F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc |
