|
| 1 | Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials (C) By mechanical means in area of light jungle |
| 2 | Dismentaling the existing structure including removing and stacking the dismentelled materials as and where directed. (A) R.C.C. work |
| 3 | Diversion of water course, providing cofferdam and bund or island as may be necessary for foundation and maintaining the same for the period as may be necessary. |
| 4 | Demarkation of road alingment including marking out road line by providing and fixing wooden pegs or steel rod of required size at every 25 M to 50 M. including excavating trenches ion both sodes of 0.30 m. x 0.30M. including supplying of labours and all materials for every work etc. complete. |
| 5 | Providing flood gauge marks on substructure as per design including painting complete. |
| 6 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification. |
| 7 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification. |
| 8 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification. |
| 9 | Excavation for foundation in sand, gravel, clay soft soils and murrum etc. including shoring, strutting dewatering as necessary and disposing of the excavated stuff as directed.(A) Depth upto 3.0 M. and lead upto 100m for 10 Cum |
| 10 | Excavation for foundation in sand, gravel, clay soft soils and murrum etc. including shoring, strutting dewatering as necessary and disposing of the excavated stuff as directed.(B) Depth from 3.0 to 6.0 M.and lead upto 100m for 10 Cum |
| 11 | Excavation in hard rock by dry-wet blasting and chiselling including dewatering preparing foundation base by proper benching and stepping and disposing of the excavated stuff as directed.(A) General blasting |
| 12 | P.C.C. M 15 ordinary grade (1:2.5:5) levelling course below approach slab complete as per drawing and technical specifications Clauses 800 and 1211 |
| 13 | Providing and fixing mild steel dowel bars of minimum 32mm dia. for anchoring by drilling holes in foundation strata including necessary bending, hooking of dowel bars and grouting the holes complete as per detailed drawing and as directed. |
| 14 | Providing concrete for plain/reinforced concrete in open foundations M 30 complete as per drawings and technical specifications. |
| 15 | Providing and fixing in position Fe 500D TMT as per detailed drawing, including cutting, bending hooking tying and welding complete and including forming the cage and lowering it in position. |
| 16 | Filling annular space around footing in rock as per technical specification. |
| 17 | Plain/reinforced cement concrete M-30 in substructure complete as per drawings and technical specification. (A) Height from 0 to 5m |
| 18 | Plain/reinforced cement concrete M-30 in substructure complete as per drawings and technical specification. (B) Height from 5m to 10m |
| 19 | Providing and casting in situ controlled cement concrete M-300 for R.C.C. work in pier cap,abutment cap and dirt wall including controlled cement concrete M-250 bed blocks or pedstals of required size below bearings as per detailed drawings, centering, shuttering, scaffolding, wherever necessary, laying vibating, curing and finishing complete.(A) 5 TO 10 M. |
| 20 | Providing and fixing in position Fe 500D TMT as per detailed drawing, including cutting, bending hooking tying and welding complete and including forming the cage and lowering it in position. (A)Part A - Substructure |
| 21 | Providing and fixing in position Fe 500D TMT as per detailed drawing, including cutting, bending hooking tying and welding complete and including forming the cage and lowering it in position. (B)Part B- Substructure - ( For cap, dirt wall ) |
| 22 | Providing and Fixing in position Tar paper asbearing as per detailed drawings. |
| 23 | Providing and fixing in position Mild steel dowel bars in pier caps or abutment caps for anchorage in fixed end as per detailed drawings including cutting, bending and welding complete. |
| 24 | Providing and fixing in position Mild steel dowel bars in pier caps or abutment caps for anchorage in free end as per detailed drawings including cutting, bending and welding complete. |
| 25 | Providing and laying reinforced cement concrete M-30 in superstructure as per drawing and technical specifications. |
| 26 | Providing and casting in situ controlled cement concrete M-30 for average 100 mm thick wearing coat laid as directed dincluding einforcement, tamping, vibrating, finishing, curing and filling in joints with bitumen complete |
| 27 | Reinforced Cement Concrete M 30 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications. |
| 28 | Providing and fixing in position Fe 500D TMT as per detailed drawing, including cutting, bending hooking tying and welding complete and including forming the cage and lowering it in position. (A)Part D - Superstructure |
| 29 | Providing and fixing in position Fe 500D TMT as per detailed drawing, including cutting, bending hooking tying and welding complete and including forming the cage and lowering it in position.(B)Part E-Approach slab |
| 30 | Providing and laying a buried expansion joint, covered with 12 mm thick, 200 mm wide galvanised weldable structrual steel plate as per IS:2062, placed symmetrical to centre line of the joint, resting freely over the top surface of the deck concrete, welding of 8 mm dia, 100 mm long galvanised nails spaced 300 mm c/c along the center line of the plate, as per technical specifications clauses 1207.2.3. , Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications, Providing and fillling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight. |
| 31 | Providing and casting in-situ Reinforced Cement Concrete M40 grade controlled cement concrete in crash barrier using 6mm to 20mm machine crushed well graded stone aggregate, sand of approved quality, OPC53 grade cement at any height including centring, shuttering, mixing with batching plant,placing in position, consolidating with mechanical vibrators, curing, deshuttering carefully, making good the damages, fixing embedment, inserts, pockets, wherever necessary as directed with F3 / U3 type exposed concrete finish and form mark as directed by Engineer-in-charge, including all leads and lifts etc. complete as per specification and drawing. |
| 32 | Providing and applying one coat of Epoxy phenolic primer of DFT 50 microns and two coats of Epoxy phenolic coating of DFT 100 microns each for RCC Element or any other equivalent epoxy coating system to all concrete surfaces exposed to atmospherein substructure and superstructure including cost of material labour, transportation,scaffolding and preparing the surface by cleaning, washing, brushing, sand/grit blasting etc complete and as directed by engineer and as per specification. ( Paint shall be approved from Engineer and tested from approved Laboratory) (Total DFT = 50+100+100 = 250 microns) |
| 33 | Drainage spouts complete as per drawing and technical specifications. |
| 34 | Providing Masonry Steps with Cement Pointing on approaches as directed. |
| 35 | Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications |
| 36 | Providing & laying filter material underneath pitching in slope complete aas per drawing and technical specification. |
| 37 | Providing and Casting in situ controlled Cement Concrete M-30 for R.C.C. Raft and cutt-off walls including necessary shuttering laying, vibrating, ramming and curing complete. |
| 38 | Earthwork for embankment including breaking clods, dressing with all lead and lift (excluding watering and consolidation)(E) From Borrow area within 3.0 Km. lead (more than 10 ton) |
| 39 | Earth work for embankment for SUBGRADE with CBR 7 % including breaking clods, dressing with all lead and lift and includingwatering, rolling and consolidation of subgrade in layers at O.M.C. to required dry density, including filling the depressing, which occurs during the process using power roller of 8 tonne to 10 tonne all as per specification. (E)From borrow area 3km lead |
| 40 | Providing and laying Compacted 150mm thick of Specified quarry spall in side shoulder including carring of Material and spreading on prepared base includong compacting as per MOST Specification etc…. Complete |
| 41 | Construction of Granular Sub Base (GSB) by providing coarse graded material of grading-I, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MORTH specification. |
| 42 | Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tripper to site, laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. |
| 43 | Providing and applying PRIMER COAT with bitumen emulsion using emulsion pressure distributor at the rate of 0.60 kg/sqm on prepared surface of granular base including clearing of road surface using mechanical brooms. |
| 44 | Providing and laying Bituminous macadam with hot mix plant using crushed aggregates ofgrading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolledto achieve the desired compaction as per Technical Specification. |
| 45 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification. |
| 46 | Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification. |
| 47 | Road Marking with Hot applied Thermoplastic compound with reflectorising glass beads on bituminous surface. Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 grams per square meter area. Thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC : 35. The finished surface to be level, uniform and free from streaks and holes. |
| 48 | Providing & fixing Cats Eye / Pavement Marker (M.M.C. vial less) made out of acrylic-styrene-acrylonitrile or hi-impact polystyrene fitted with molded of methacrylate (MMC) reflector cube corner reflector design, filled with tightly adhering potting compound as per ASTMD 788 size 8 cmX8 cmX1.5 cm provided with bituminous adhesive in sufficient quantity with each unit for fixing no nail should be allowed for fixing Reflectors on both sides minimum reflective area 12.9 Sq.cm on each face. Compressive strength 13 tonnes at 230 C temperature (B) Double Side lenses. |
| 49 | Hazard Marker Sign :-Providing and fixing sign boards made out of l.5mm aluminium sheet / 3mm ACP (Aluminum composite Panel); size 90x30 cms. rectangular as per design of IRC-67-2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ;reflectorised with Micro Prismatic Grade retro refiective sheeting of Type-11 as per ASTM D 4956 and latest M.O.S.T.Specifications; 1.8mtr long stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with best quality epoxy coatings in black and white bends. The details of symbol for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC block of size 45 x 45 x 60 cms. for each leg.including excavation, curing etc. complete under the supervision of engineer in charge. A warranty for 10 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (A) Class-C Type-11 Retro Reflective sheeting |
| 50 | Facility Informatory Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP (Aluminum composite Panel); size 80 x 60 cms. rectangular as per design of IRC-67-2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint; reflectorised with micro Prismatic Grade retro refiective sheeting of Type-11 as per ASTM D-4956 and latest M.O.S.T. Specifications; 3.6mtr long stand post of 75 x 75 x 6mm / 65 NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with best quality epoxy coatings in black and white bends. The details of symbol for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing etc.complete under the supervision of engineer in charge. A warranty for 10 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (A) Class-C Type-11 Retro Reflective sheeting. |
| 51 | Providing and fixing of a typical design of PMGSY Informatory Sign Board “The board will be a composite unit consisting of three plates of Aluminum Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most plate will be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mm x 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart Centre to Centre. The top of the middle plate will be flushed with the top of 75 mm dia. medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond Shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. ii). the lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 Messages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing.” |
| 52 | Cautionary Warning Sign :-Providing and fixing sign boards made out of 2mm aluminium sheet / 4mm ACP (Aluminum composite Panel); size 90 x 90 x 90 cms. equilateral triangle as per design of IRC-67-2012. Pre treated with phospheting process & acid etching; coated with one coat of epoxy primer and two coats of best quality epoxy paint ; reflectorised with High Intensity Prismatic Grade retro refiectivesheeting of Type-4 as per ASTM D-4956 and latest M.O.S.T.Specifications; 3.6mtr long stand post of Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as required and frame fabricated from suitable size iron angle of 35 x 35 x 3mm; painted with bestquality epoxy coatings in black and white bends. The details of symbol for each board shall be as per the instruction of engineer in charge. The fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for each leg including excavation, curing etc.complete under the supervision of engineer in charge. A warranty for 7 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor exposure test report from third party test lab for the product offered shall be submitted by contractor. (B) Class-B Type-4 Retro Reflective sheeting |
| 53 | Providing and fixing \"W\" type safety barrier using M.S. iron channel 150mm x 75m x 5mm size erected at 2.0 Mt. center to center and providing \"W\" shaped galvanised steel sheet guard rail 3mm thick for crash barrier in single row as per detailed drawing with fabrication and installation charges including providing foundation block of size 0.60 x 0.60 x 0.75 Mt. in C.C. 1:2:4 and oil painting two coats with one coat of red oxide etc complete. |
| 54 | Providing and laying of Extruded 30 KN as per apprival design and specification with accessories like tie strips, nuts & bolts and loops / luge for joining reinforcing elements with the facia , Pannels and overlaps and other protective elements as per detailed specification. |
| 55 | Providing and laying of Extruded 40 KN as per apprival design and specification with accessories like tie strips, nuts & bolts and loops / luge for joining reinforcing elements with the facia , Pannels and overlaps and other protective elements as per detailed specification. |
